Manufacturing Commons^™

Processing, Characterization And Performance Of Ceramic Liners For Hydrogen Gas Turbine Engines, Fahim Faysal

Graduate Studies Theses and Dissertations 2026

Advanced ceramics and ceramic matrix composites (CMCs) are known for their endurance at high temperatures. This study investigated the fabrication and testing of two material systems: silicon carbide nitride (SiCN) reinforced with yttria-stabilized zirconia (YSZ) fiber manufactured through polymer infiltration and pyrolysis (PIP), and 3D-printed alumina (Al₂O₃) ceramics. The CMC thermal stability at high temperatures was explored through a hydrogen torch test. The CMC surface could withstand a temperature of 1,400°C for 10 minutes during the torch test. Furthermore, the internal surface of a hydrogen combustion chamber was coated with CMC to assess its applicability as a protective barrier against …

Influence Of Build Plate Location On Tensile Properties And Residual Stresses In Lpbf-Fabricated Stainless Steel 316 Components, Yareli Zelaya Pavón

Honors Program Theses and Research Projects

Additive manufacturing (AM), particularly Laser Powder Bed Fusion (LPBF), enables rapid production of complex metal components with minimal waste. Stainless Steel 316 (SS316) is widely used in engineering applications due to its corrosion resistance and mechanical reliability. This study investigates the influence of build plate location on tensile properties and residual stresses in LPBF-fabricated SS316. Twelve tensile specimens and nine unsupported bridge structures were fabricated at different build plate positions using a “machine model.” Tensile testing provided stress-strain data to evaluate peak stress, elastic modulus, and strain at break, while bridge curvature measurements quantified residual stress through warping. Results indicate …

Hydrogen Embrittlement In Shot-Peened Steel, Jia-Huei Tien, David R. Johnson, David Bahr

15th International Conference on Shot Peening

This work investigates the role of shot peening on hydrogen embrittlement resistance in quenched and tempered 1070 steel. Thermal desorption spectroscopy results revealed that shot-peened specimens contained nearly twice the hydrogen (H) content of unpeened samples when charged under the same electrochemical conditions, suggesting the introduction of additional trapping sites occur during peening. The mechanism underlying this behavior can be associated with increased dislocation density and is more consistent with the HELP mechanism. Residual stress measurements show a significant relaxation of compressive stresses in shot-peened specimen after H charging, indicating H enhanced dislocation rearrangement. Both unpeened and peened specimens exhibited …

Anisotropic Residual Stress Measurements In Additively Manufactured 316 Stainless Steel Parts, Rajeshree Varma, Donovan Stumpf, Paul R. Mort

15th International Conference on Shot Peening

Additive manufacturing (AM) using laser powder bed fusion (L-PBF) is increasingly used to produce complex parts for industries like aerospace and medical devices. The intrinsic characteristics of AM – layer-wise deposition and rapid thermal cycling – generate significant, anisotropic, residual stresses that can compromise part quality and performance. Recent studies highlight how these stresses are strongly influenced by process parameters and build orientation. X-ray diffraction (XRD) techniques, including sin²ψ and advanced two-dimensional approaches, have become the preferred methods for non-destructive, directionally resolved measurement of residual stress in AM metals. This review surveys advancements in XRD residual stress methods with a …

From Strain To Stress: Stress Map Testing Of Almen Strips, Donovan Stumpf, Rajeshree Varma, Paul R. Mort

15th International Conference on Shot Peening

Almen strips have long been used to evaluate shot peening intensity, with arc height serving as a proxy for compressive residual stress. Stress mapping tests (SMT) in this work involve the controlled flattening of an Almen test strip onto a spatial pressure sensor, acting as an inferential measurement for the net bending moment caused by the relaxation of the peened strip. This work explores how stress mapping tests add insight into the stress state of Almen strips, potentially offering a fast and practical alternative to residual stress depth profiling. SMT data analysis provides a framework for relating Almen gauge height …

Fourier Analyses Of Optical Profilometry As An Inferential Measurement For Impact Coverage., Langdon Feltner, Paul Mort

15th International Conference on Shot Peening

A critical consideration in peening process design is achieving sufficient impact coverage. Conventional methods for assessing coverage rely on manual inspection, which is time-consuming and poorly suited for automated control. In this work, we investigate the use of frequency-domain analysis to quantify surface modification in peened samples using optical profilometry (OP) data. Three-dimensional surface maps of Almen strips were acquired using a high-resolution OP system and analyzed via fast Fourier transform (FFT) to compute spatial power spectral densities (PSDs). PSD maps and radially averaged profiles reveal consistent amplification of harmonic components similar to the nominal particle size, with increasing intensity …

Comparison Of Peening Effect Between Additive Manufacutred And Drawing Titanium Alloy, Hitoshi Soyama

15th International Conference on Shot Peening

Although additively manufactured (AM) metals are attractive materials, their remarkable weak fatigue properties are an obstacle to their practical application. Thus, post-processing to improve their fatigue properties is required. In the present study, powder bed fusion using laser sintering titanium alloy, i.e., PBF-LS/Ti6Al4V was treated by shot peening (SP), submerged laser peening (SLP), cavitation peening (CP), and fine particle bombarding (FPB), then the fatigue properties were investigated by a torsional fatigue test, comparing with drawing Ti6Al4V. It was revealed that the fatigue strength at 10⁷ was 446 ± 5 MPa for PBF-LS/Ti6Al4V treated by FPB+CP, 359 ± 9 MPa …

Reduced Order Approach For Peening Stress Field Variability, Langdon Feltner, Paul Mort

15th International Conference on Shot Peening

A common goal in shot peening research is to connect operational parameters to resultant residual stress fields, providing a means to control and optimize the effectiveness of surface treatment. In practice, experimental measurements of residual stresses are often averaged values over regions that are large in comparison to an impact dimple. In fact, the stochastic nature of impact locations leads to residual stress fields that are distributed. Finite element peening simulations confirm this observation. The goal of this report is to connect operational parameters to localized fluctuations in residual stress through probabilistic reasoning (Figure 1). In particular, the development of …

Investigations On The Fatigue Strength Of Threads Produced By Different Fabrication Techniques, Philippe Du Maire, Jürgen Hoffmeister, Andreas Öchsner, Michael Johlitz

15th International Conference on Shot Peening

The increasing importance of sustainability in engineering demands the development of long-lasting, high-performance components that reduce material and energy consumption over time. This study investigates how different thread manufacturing processes, i.e., cutting, rolling, and deep rolling, affect the fatigue strength of bolts made from 42CrMo4+QT steel. Cylindrical specimens with M12 threads were subjected to cyclic tensile loading with constant mean stress. Fatigue strength was evaluated using the staircase method, and supporting analyses included X-ray diffraction for residual stress, and full width half maximum examination and Vickers microhardness measurements. Results show that thread rolling significantly improves fatigue strength, achieving 113.8 MPa …

Effect Of Fine Particle Peening Induced Material Transfer On The Initial Deposition Behavior Of Nickel Electroplating On Aluminum Substrate, Kazuki Iijima, Yutaka Kameyama, Hideaki Sato, Shuhei Kodama

15th International Conference on Shot Peening

Plating on aluminum requires a complex zincate pretreatment. Fine Particle Peening (FPP), using particles ≤200 µm, has gained attention as an alternative due to its ability to transfer particle components onto the surface, potentially improving deposition and adhesion. Previous studies showed enhanced plating on aluminum treated with steel particles. This study investigates the effectiveness of FPP as a pretreatment for nickel electroplating by examining initial deposition behavior. A1050-H24 aluminum was treated using FPP with either steel or glass particles, compared to an untreated specimen. Steel particle FPP created a lamellar microstructure with alternating iron and aluminum phases. EBSD revealed that …

The Effect Of Surface Treatment On The Fatigue Strength Of Sus316l Additive Manufactured Products, Hitoshi Nishijima, Yuji Kobayashi, Toshiya Tsuji, Kiyotaka Masaki

15th International Conference on Shot Peening

Rotating bending fatigue tests were conducted to investigate the effect of shot peening and barrel finishing on fatigue properties of SUS316L made by laser PBF which was one of additive manufacturing processes. Surface roughness, residual stress, and fatigue strength were investigated for each specimen. As a result, the fatigue strength of the barrel finished specimens was almost same or better than that of the shot peened specimens. Barrel finished specimens increased 4.1 times higher fatigue strength than as-built specimens. The surface roughness of the specimens after barrel finishing was reduced by up to 96% compared to the as-built specimens. On …

Effects Of Laser Peening On Fatigue Properties Of Welded Aluminum Thin Plates, Kiyotaka Masaki, Yoshio Mizuta, Satoshi Tamaki, Yuji Sano

15th International Conference on Shot Peening

To improve the fatigue properties of welded aluminum alloy thin plates used in transportation machinery, handheld laser peening (HH-LP) was applied to 2 mm-thick A5083-O specimens prepared by bead-on TIG welding. Conventional laser peening often causes warping in thin plates, but the HH-LP treatment using low-energy laser pulses avoids this problem. The HH-LP treatment introduced compressive residual stresses of over 200 MPa on the heat-affected zone (HAZ) of the welded specimens. Fatigue tests under plane bending conditions revealed that the HH-LP treatment significantly improved the fatigue strength of the welded specimens, achieving a level comparable to that of the base …

Microstructural Changes And Residual Stress Generation On The Periodically Patterned Surface Texture Fabricated By Angled Fine Particle Peening, Yutaka Kameyama, Hideaki Sato, Ryokichi Shimpo

15th International Conference on Shot Peening

Focusing on the potential of peening technology as a surface texturing technique, angled fine particle peening (angled-FPP) has been proposed to fabricate a specific periodical surface structure, which possibly provides various surface functions. It is necessary to further characterize the textured surface to earn more advantages from angled-FPP. Thus, in this paper, texture formation phenomena, residual stress, and microstructural changes were investigated on the angled-FPP specimens.

Improving Fatigue Strength And Life Of Single Crystal Cmsx-4, Jochen Peter Fuhr, Lloyd Hackel, Nicolau I. Morar, Noah Holtham, Keivan Davami, Montu Sharma, Rajkumar Roy

15th International Conference on Shot Peening

The deep penetration of laser peening (LP) and retention of residual stress at high temperature by LP is significant in improving fatigue life and strength of superalloys exposed to high temperature and corrosion. Single crystal CMSX-4, was evaluated for stress relaxation and both fatigue life and fatigue strength of material that was LP-treated compared to non-LP and shot-peened (SP) specimens. LP was done with multiple layers using a 20 J/pulse laser where the laser high energy enabled using a 5 mm spot size on the metal surface. Stress measurements by the slitting technique showed the plastic penetration depth exceeded SP …

Recent Progress And Scientific Challenges In Wire-Arc Additive Manufacturing Of Metallic Multi-Material Structures, Sainand M. Jadhav, Sambhaji Kusekar, Akash Belure, Satyavan Digole, Abhijeet Mali, Muralimohan Cheepu, Manoj Mugale, Suhas Alkunte, Duckbong Kim

Faculty Articles

Metallic multi-material structures are heterogeneous structures characterized by changing composition, microstructures, and site-specific characteristics, advantageous for numerous applications where multifunctionality is desired. Metallic multi-material structures are known as bimetallic structures (BSs), which are functionally graded materials (FGMs). In recent years, wire-arc additive manufacturing (WAAM) advanced as a promising additive manufacturing process to realize the fabrication of these structures due to its high deposition rate, cost-effectiveness, and material utilization efficiency. This review presents a comprehensive overview of the recent progress, processing strategies, and scientific challenges in WAAM of multi-material structures. The paper begins with an introduction to multi-material structures, followed by …

Material Extrusion 3d Printing Of Metal Alloy: Material, Methods And Application., Sihan Zhang

Electronic Theses and Dissertations

Material extrusion (MEX) additive manufacturing presents a promising pathway for producing metal components with complex geometries while avoiding the safety hazards associated with loose powder handling in conventional metal additive manufacturing processes. This dissertation investigates the development and optimization of MEX processes for aluminum alloys, addressing critical challenges in feedstock formulation, printing parameter optimization, and post-processing strategies. Three distinct approaches were explored to advance the capabilities of aluminum MEX: filament-based processing of 6061 aluminum, paste-based extrusion of 6061 aluminum, and development of a novel aluminum-magnesium-tin alloy system for space manufacturing applications. The filament-based approach successfully demonstrated the production of 6061 …

In-Situ Defect Detection In Selective Laser Melting Using Convolutional Neural Networks, Ethan Gaigalas

Master's Theses

This thesis develops and trains a convolutional neural network (CNN) to classify defects in metal parts produced by selective laser melting (SLM) using acoustic emission (AE) data. The model successfully identified porosity and standard build layers with high accuracy but consistently struggled to classify lack of fusion (LOF) defects, regardless of input type, normalization, or class count. These results suggest that while AE signals contain distinguishable features for certain defect types, LOF signals may be too subtle or inconsistent for reliable detection. The study addresses the ongoing challenge of in-situ quality monitoring in metal additive manufacturing, where defects like cracks, …

3d Printed Fixed Wing Aircraft Competition, Sidney E. Long, Mitchell Heise, Jack Bride, Daniel Salinas

Mechanical Engineering

Cal State LA and Arlington University, Texas are hosting the same 3D printed, fixed wing aircraft competition for 2025. Cal Poly requires a competitive plane that can adhere to each rule and be piloted remotely to achieve the longest time in the air. The plane must utilize solely 3D printing technology for the wings, body, and all other structures. The only off-the-shelf components can be the motor and electronics, as well as mechanical devices such as hinges.

Design Principles For Robotic-Controlled 3d Printing Of Soft Tissue-Mimicking Materials, Karina Mealey

Master's Theses

Geometrically and physically accurate 3D models are emerging as essential tools for surgeons in pre-operative planning and training, but current methods of producing these models are not sufficient. Existing solutions have downsides such as high costs, long and tedious production times, high complexity resulting in a lack of scalability, or an inability to meet material requirements for accurately simulating human tissue.

The objective of this work is to develop principles for a low-cost, easy-to-use 3D printing system capable of prototyping with soft tissue-mimicking materials. To pursue this goal, a MyCobot280 robot arm was used as the mechanism to explore the …

Comparative Study Of Experimental And Fea Strain Data For Cnt-Coated Fiberglass Sensors, Extensometers, And Metal Foil Strain Gauges, Omar Dwidar

Master's Theses

Material testing is essential across industries such as aerospace, automotive, and construction, playing a critical role in verifying material selection, diagnosing failures, and understanding the development of flaws in structures. These insights are key to designing successful, reliable systems. Conventional metal foil strain gauges are low cost and reliable but provide limited sensitivity with a typical gauge factor around 2. Extensometers provide highly sensitive strain measurements with the disadvantage of a bulky form factor. With advanced materials such as carbon nanotubes, it is possible to manufacture a sensor with the sensitivity closer to that of an extensometer with the small …

Effect Of Manufacturing And Machining Process On Recycled Composite Connecting Rods Under Tension And Compression, Walter W. Oppelt

Master's Theses

Carbon fiber reinforced polymer (CFRP) is an engineering material renowned for its high-strength and low-density material properties. Such properties make CFRPs especially useful for applications across many industries, including aerospace, automotive, marine, sporting goods, oil and gas, and more. However, with such favorable material properties comes the cost of high energy usage required to produce raw carbon fiber. Recycled carbon fiber (rCF) has emerged as a promising alternative, offering a significant reduction in energy usage. This research explores the viability of applying recycled CFRPs to internal combustion engines to both reduce energy costs during manufacturing and while in use. Mechanical …

Using Predictive Analytics To Reduce Small Business Cost Estimation Error, Diana Solt

Journal of Applied Packaging Research

Small and medium packaging companies generally employ the use of custom-developed quoting programs to bid goods and services. Custom bid programs (e.g. Excel) are used to capture the company-specific costs of production. The inputs of variable costs, such as machine rate and scrap rate, are critical to get correct; however, companies often rely on educated guesses and industry expertise to quote packaging products to end-users. Due to the guesswork involved there can be a financial difference between the quoted costs and actual costs. This variance is often the cause of significant lost dollars. Price, if not determined correctly, could negatively …

Thermal Characterization Of 3d Printing Materials For Increasing Insulation Potential And Practicality, Jackson H. Minnick

Mechanical Engineering Undergraduate Honors Theses

This study served as an exploration into the possible existence of a correlation between the infill lattice structure of a 3D printed wall section and the thermal performance of that sample as characterized by thermal conductivity measured in units of Watts per meter Kelvin. With the continual increase in the practicality, fidelity, and applicable fields of additive manufacturing, namely FDM 3D printing, research on specific print characteristics and their effects on the material and thermal characteristics of the part in question is steadily becoming more commonplace. Although the thermal conductivity of 3D printed wall sections as a function of infill …

Ultrafast Laser Surface Structuring For Wettability Control On Copper, Akshay Arvind Nagvenkar

All Theses

Wettability is a crucial surface property influencing various phenomena, including heat transfer, cell adhesion, and corrosion. Engineering devices can achieve superior performance by precisely manipulating surface wettability. As a result, extensive research has focused on developing surfaces that exhibit either extreme water attraction (superhydrophilic) or strong water repellency (superhydrophobic). Tailoring surface wettability paves the way for numerous applications, such as drag reduction in marine vessels, controlled drug delivery, efficient water collection, advanced liquid transport systems, oil-water separation, anti-corrosion coatings, friction reduction, and self-cleaning materials. Ultrafast laser surface structuring is a promising approach for engineering multifunctional surfaces, effectively modifying material properties …

Exploring Metal Additive Manufacturing In Martian Atmospheric Environments, Zane Mebruer

Mechanical Engineering Undergraduate Honors Theses

On-surface manufacturing is key to the success of a planetary colonization, especially that of Mars. However, traditional subtractive manufacturing processes are equipment, energy, and material intensive, meaning novel additive manufacturing (AM) processes must be pursued for this end. Selective laser melting, one of the most effective and versatile AM methods, would be incredibly beneficial to a Martian mission but requires an artificial argon atmosphere to create effective parts. The purpose of this study was to examine if carbon dioxide, the gas that makes up over 95% of Mars’ surface atmosphere, would be a sufficient substitute for argon in SLM fabrication. …

Adjustable Dynamometer Motor Mount, Garrett Carson Ng, Elijah Siegel Reuven, Ethan Fong, Daniel Larimer

Mechanical Engineering

The Cal Poly Electrical Engineering Department and sponsor Dr. Dolan needs a manufacturable motor fixture that securely aligns motors of various sizes with dynamometers. Previous lab motor fixtures could not accommodate motors of different sizes, making precise alignment between motors and dynamometers time-consuming and unreliable. Our team developed a modular, manufacturable fixture capable of aligning various motor sizes quickly, accurately, and securely, enhancing lab consistency and usability.

Manipulating Martensitic Transformation And Residual Stress Development In Stress Superposed Incremental Forming Of Ss304, Elizabeth M. Mamros, Fabian Maaß, Thomas Gnaupel-Herold, A. Erman Tekkaya, Brad L. Kinsey, Jinjin Ha

Faculty Journal Articles

Stress superposition is one of the strategies used in metal deformation processes to increase the material formability, decrease the required forming forces, and create highly customized components. To investigate the effects of tensile and compressive stresses superposed to the single point incremental forming (SPIF) process, experiments and numerical simulations were conducted for a stainless steel 304 (SS304) truncated square pyramid geometry. Tensile stresses were superposed in-plane on the specimen blank by a custom hydraulic frame, and compressive stresses were incorporated via a polyurethane die. Identified parameters for a martensitic transformation kinetics model for SS304 were used in a two-step finite …

Advanced Manufacturing Of Multifunctional Shape Memory Polymer Composites And Self-Healing Systems, John B. Konlan

LSU Doctoral Dissertations

The need for multifunctional light weight structures for engineering applications is on the rise. Multifunctional composites are desired because of their ability to combine multiple functionalities into one structure. The advantages of a high strength-to-weight ratio of multifunctional composites make them desirable and suitable for use in energy-efficient applications. Shape-memory polymers (SMPs) have attracted interest over the past several decades because of their multifunctional nature. They have found use in many applications such as aerospace, satellites, automobiles, textiles, and biomedical devices, where lightweight and multifunctionality are key. The self-healing nature of most SMPs makes them suitable for use in lightweight …

Fabrication Of Ultra High-Temperature Compact Heat Exchanger By Extrusion-Based Ceramic Additive Manufacturing, Abid Hasan Rafi, David W. Lipke, Jeremy Lee Watts, Greg Hilmas, Ming-Chuan Leu

Miners Solving for Tomorrow Research Conference

No abstract provided.

Additive Manufacturing Of Thermoplastic Composites, Matik Heskin, K. Chandrashekhara, Richard Billo, Ming-Chuan Leu, Thomas P. Schuman

Miners Solving for Tomorrow Research Conference

No abstract provided.