Heat Transfer, Combustion Commons^™

Fluid Analysis In Solar Heat Pipes, Ben Krumholz, Michael Agavo, William Dundon

Mechanical Engineering

Evacuated tube solar collectors are efficient systems that use heat pipes to facilitate heat transfer. They use incoming solar radiation to heat water. Professor Mason Medizade tasked the team with choosing a component of the system to research and test its influence on system performance. The team investigated the working fluid that runs through the heat pipes. Distilled water, acetone, and ethanol at a range of fill volumes form 1 mL to 11 mL were tested. The team's goal was to find a volume for each fluid to maximize performance of the system. Performance was defined as average temperature rise …

Me 350 Air Conditioning Experiment, Joshua Baida, Ellie Hallner, Tyler Eschenbach

Mechanical Engineering

In keeping with Cal Poly's focus on physically applying the concepts learned in the classroom, our team of engineering students has compiled a laboratory experiment displaying the basic thermodynamic cycle found in air conditioning systems. This vapor compression cycle is displayed on a visualization board that features all four major components of the system: the compressor, the evaporator, the condenser, and the throttling valve. Students will take measurements of temperature and pressure at each stage in the cycle and also gauge the power draw from the compressor to gain an understanding of how performance and electricity cost come into play …

Micro Debris Generator, Gordan Bradaric, Ross Byers, Stephen Quanci

Mechanical Engineering

This senior project team at Cal Poly consisting of Stephen Quanci, Gordan Bradaric, and Ross Byers has been commissioned by Erik Brown of Lawrence Livermore National Labs to create a way to reliably and consistently entrain microscopic particles into the hot HTTU flow. These particles will be used to compare the loading rates of new HEPA filters by measuring the pressure drop across the filter. The generated particles would simulate typical conditions in which these HEPA filters are expected to operate, namely fine ash. The particles used for loading the filter are intended to simulate the particulate reaching the LLNL …

Efficiency Testing Of An Electronic Speed Controller, Grace Cowell, Matthew Hudson, Marcus Pereira

Mechanical Engineering

This project required the development of a rig that could experimentally determine the efficiency of an Electronic Speed Controller (ESC). The selected design focuses on measuring the losses due to heat from the device and comparing this to its input power. The selected design is a flow rig that utilizes the heat equation q=ṁcpΔT. The rig provides a steady state measurement of the ESC heat output by passing a known mass flow rate of air across the ESC and measuring the temperature difference. It uses a flowmeter to determine ṁ, thermocouples to determine ΔT, and a table lookup to determine …

A Study Of Constant Voltage Anemometry Frequency Response, Alex D. Powers

Master's Theses

The development of the constant voltage anemometer (CVA) for the boundary layer data system (BLDS) has been motivated by a need for the explicit autonomous measurement of velocity fluctuations in the boundary layer. The frequency response of a sensor operated by CVA has been studied analytically and experimentally. The thermal lag of the sensor is quantified by a time constant, M_CVA. When the time constant is decreased, the half-amplitude cut-off frequency, f_CVA, is increased, thereby decreasing the amount of attenuation during measurements. In this thesis, three main approaches have been outlined in theory and tested experimentally …

Continuum Modeling Of The Densification Of W-Ni-Fe During Selective Laser Sintering, Connor M. West

Master's Theses

The purpose of this thesis is to effectively model the time history of the temperature distribution during the selective laser sintering process and use this information to investigate the resulting relative density. The temperature is a critical parameter of the process because it directly effects the overall quality of the part. First, an efficient, affordable, and reliable simulation was developed within the finite element software, Abaqus. Next, the results from the simulations were compared to the experimental results performed by Wang et al. (2016). The FEA model consisted of a 3 layer simulation. Multiple simulations at various laser recipes were …

Final Project Report: Heliostat-Concentrator Solar Cooker, Ian Davison, Devin Mast

Mechanical Engineering

This document is the full report for the senior project of Cal Poly Mechanical Engineering students Ian Davison and Devin Mast. The report encompasses the full project process, including background research, identification of need, design requirements, design development, proposed design, design realization, changes to proposed design, and design verification. We were tasked with the design and manufacture of a “dual mirror” solar cooker to verify a concept for a new type of off-axis parabolic solar cooker conceived by Dr. Pete Schwartz, the sponsor of the senior project and a physics professor at Cal Poly. Previously, off-axis parabolic solar cookers have …

High Temperature Hepa Filter Test Unit Upgrades, Alexander Krippner, Ian Corcorran, Michael Burlando

Mechanical Engineering

No abstract provided.

Axisymmetric Bi-Propellant Air Augmented Rocket Testing With Annular Cavity Mixing Enhancement, Allen A. C. Capatina

Master's Theses

Performance characterization was undertaken for an air augmented rocket mixing duct with annular cavity configurations intended to produce thrust augmentation. Three mixing duct geometries and a fully annular cavity at the exit of the nozzle were tested to enable thrust comparisons. The rocket engine used liquid ethanol and gaseous oxygen, and was instrumented with sensors to output total thrust, mixing duct thrust, combustion chamber pressure, and propellant differential pressures across Venturi flow measurement tubes.

The rocket engine was tested to thrust maximum, with three different mixing ducts, three major combustion pressure sets, and a nozzle exit plane annular cavity (a …

Active Fog Catcher, Michael Giglio, Carson Hand, William Beechinor, Kai Zhang

Mechanical Engineering

The active fog catching senior project team has been asked to develop a device that will harvest water from the atmosphere, namely fog, using active means. The project will be centered on maximizing water collection rate, with efficiency as a secondary concern. The final design utilizes a refrigeration system in which fans pull air across the cold evaporators inside of a duct. Water condenses on the evaporators and drain into a collection container. It was decided to focus on maximizing water collection at the cost of efficiency because the feasibility of actively harvesting fog must be proved before trying to …

Increasing Isentropic Efficiency With Hydrostatic Head And Venturi Ejection In A Rankine Power Cycle, Nathan Daniel Ruiz

Master's Theses

This thesis describes the modifications made to the Cal Poly Thermal Science Laboratory’s steam turbine experiment. While the use of superheating or reheating is commonly used to increase efficiency in a Rankine cycle the methods prove unfeasible in a small scale project. For this reason, a mathematical model and proof of concept design using hydrostatic head generated by elevation and venturi ejection for use by the condenser is developed along with the equations needed to predict the changes to the system. These equations were used to create software to predict efficiency as well as lay down the foundation for future …

Development Of An Autonomous Single-Point Calibration For A Constant Voltage Hot-Wire Anemometer, Ryan Murphy

Master's Theses

Traditionally, the measurement of turbulence has been conducted using hot-wire anemometry. This thesis presents the implementation of a constant voltage hot-wire anemometer for use with the Boundary Layer Data System (BLDS). A hot-wire calibration apparatus has been developed that is capable of operation inside a vacuum chamber and flow speeds up to 50 m/s. Hot-wires operated with a constant-voltage anemometer (CVA) were calibrated at absolute static pressures down to 26 kPa. A thermal/electrical model for a hot-wire and the CVA circuit successfully predicted the measured CVA output voltage trend at reduced pressure environments; however, better results were obtained when the …

Benchmarking, Characterization And Tuning Of Shell Ecomarathon Prototype Powertrain, Eric J. Griess

Master's Theses

With the automotive industry ever striving to push the limits of fuel efficiency, the Shell EcoMarathon offers a glimpse into this energy conserving mindset by challenging engineering students around the world to design and build ultra-efficient vehicles to compete regionally. This requires synchronization of engineering fields to ensure that the vehicle and powertrain system work in parallel to achieve similar goals.

The goal for Cal Poly – San Luis Obispo’s EcoMarathon vehicle for the 2015 competition is to analyze the unique operating mode that the powertrain undergoes during competition and improve their current package to increase fuel efficiency. In this …

Development Of Local Transient Heat Flux Measurements In An Axisymmetric Hybrid Rocket Nozzle, Christopher D'Elia

Master's Theses

A method of performing local transient heat flux measurements in an uncooled axisymmetric hybrid rocket nozzle is presented. Surface temperatures are collected at various axial locations during short duration tests and post processed using finite difference techniques to determine local transient heat fluxes and film coefficients. Comparisons are made between the collected data and the complete Bartz model. Although strong agreement is observed in certain sections of the nozzle, ideal steady state conditions are not observed to entirely validate the Bartz model for hybrid rocket nozzles. An experimental error analysis indicates the experimental heat fluxes are accurate within ±5.2% and …

Mhttu Implementation Final Project Report, Angelica Ramirez, Julian Samayoa, Matt Keeble

Mechanical Engineering

Lawrence Livermore National Laboratory has invested considerable effort in developing fireproof high-efficiency particulate air (HEPA) filters. Due to the nature of LLNL’s research, the air leaving its lab facilities must be filtered before it is released into the atmosphere; thus, each laboratory is equipped with large banks of HEPA filters through which all internal air is exhausted. Over the years, however, fires have erupted in the labs and entire banks of HEPA filters have been destroyed, resulting in repairs and crucial downtime that prove costly.

Engineers and scientists alike have been seeking a permanent solution to this problem, and one …

Temperature Controlled Packaging Container For Biologics And Pharmaceuticals, Melinda Phan, Yufay Chow-Yee, Abraham Ho

Mechanical Engineering

Clinical Supplies Management, Inc. (CSM) provides clinical trial services to biotechnology and pharmaceutical companies by shipping pharmaceuticals to clinics and other patients. In winter 2014, CSM presented a temperature control packaging project to the Cal Poly Senior Project class. As a result, three Cal Poly Mechanical Engineering Students were tasked to design, manufacture, and qualify a shipping container that would maintain ten 10 mL vials between 2-8°C for 96 hours. The final product would have to cost less to ship than the Credo Cube, CSM’s current temperature control packaging product. After considerable research and analysis on possible temperature control technologies, …

Formula Sae Cooling System Design, Lisa Van Den Berg, Brandon Lofaro

Mechanical Engineering

The overall objective of this senior project is to develop, via testing and analysis, a guided process that will aid the Cal Poly Formula SAE team in designing their cooling system. More specifically, a set of designed tests will yield the results necessary in determining a combination of fan and radiator that will achieve appropriate cooling.

A test section that has the capability of interfacing with both the wind tunnel in the Thermal Science Lab and a radiator will be used to facilitate the necessary experiments. The wind tunnel is powered by fan controlled by a variable frequency drive that …

Sodhana Environmental - Final Design Report, Eric Taylor, Corissa Bellis, Cody Perez, Cameron Zeller

Mechanical Engineering

A fully designed cost-effective, sustainable, toilet for the developing world.

Heat Transfer Experiment: Energy Conservation, Ben Ward, Brett Wallace, Ryan Waltman

Mechanical Engineering

This proposal, prepared for the Mechanical Engineering Department by the HTEC design team will redesign and replace the current energy conversion lab that is inaccurate and out of date. The team will evaluate methods of energy conversion, specifically using braking systems, as well as existing labs in order to design an accurate and relatable experiment for this lab. The project team will work with Professor Kim Shollenberger in order to design an experiment that demonstrates energy conversion through the first law of thermodynamics while utilizing a common device that is practical in student’s lives. The final result of this project …

Ramjet Combustion Chamber, Paul Cameron Stone

Aerospace Engineering

A ramjet combustion chamber is designed and some initial assembly fabrication and test completed as a component of a ramjet graduate project for California Polytechnic State University, San Luis Obispo Supersonic Wind Tunnel. The combustor design is driven by a theoretical model created by a Cal Poly graduate student, Harrison Sykes. Temperature, pressure, and fuel flow will be measured.

Lunalight - Bringing Light To The Expanding World, Gabriela M. Igel, Daniel J. Patrick, Kimberley M. Smith

Materials Engineering

The LunaLight, a solar rechargeable light and cell phone charger, addresses the lack of access to electricity faced by 1.4 billion of the world’s population (International Finance Corporation). The LunaTech team has developed a product that is bright, simple, compact, versatile and competitive with existing products. Through a partnership with the non-profit organization One Million Lights, LunaTech has improved a previous team’s design to address user feedback, concerns of durability, and manufacturability.

The LunaLight design includes a 5 component plastic housing held together by 4 screws, a surface mounted PCB, a lithium-ion (Li-Ion) battery, one high-brightness LED, a solar panel, …

Barbeque Grill Temperature Distribution Design Improvement, Peter Gobell, Connor Mcgill, Thomas Willson

Mechanical Engineering

Team License to Grill set out to asses Bull Outdoor Products, Inc.’s barbeques and quantify the apparent uneven temperature distribution or “hot spots” and “cold spots” across the grill. This testing was accomplished with the design and fabrication of a test fixture allowing for accurate and repeatable temperature collection across the barbeque. With results that matched the sponsor’s claims of hot and cold spots, an engineering model was made using heat transfer and thermodynamic equations. Once the model somewhat resembled the experimental data, it was used to suggest different modifications that would allow for better temperature distribution. It was discovered …

High Temperature Filter Test Unit Upgrades, Blair Frandeen, Will Schill, Erick Shewmaker, Joshua Turgeon

Mechanical Engineering

The purpose of this project was to improve the existing High Temperature Filter Test Unit (HTTU) by optimizing performance and adding new features. These features include viewing ports and a camera system for observation of tests, a leak detection system, and a flame impingement system. Additional considerations included improving the current operation of the HTTU by reducing test time and energy loss. The HTTU is designed to test High Efficiency Particulate Air (HEPA) filters at temperatures up to 1300 ˚F, creating conditions which simulate a fire in a chemical processing facility. The HTTU was originally built as a Cal Poly …

Rapid Tool Heating, Jason Chi, Bobby Dodge

Mechanical Engineering

Quatro Composites creates various molded parts for an array of industries. They are seeking to improve their thermoplastic molding process by decreasing the amount of time to heat up the steel tool that molds the thermoplastics. Currently, it takes approximately 1 hour to heat up their 120 pound steel mold from room temperature to approximately 700°F. The goal of this project is to create an optimum heating method that will minimize that heating time to about 20 minutes or less. It is critical for the stakeholders (Quatro Composites) to have a faster heating time in order to increase their production …

Rocket Fuel Pressurization, Sean Green, Joe Marcinkowski, Andrew Nahab

Mechanical Engineering

No abstract provided.

Kase, The Laptop Cooling Case, Jana Morrison, Tyler Ries

Biomedical Engineering

This report describes the final design and analysis of a laptop cooling case as a marketable product for a group of entrepreneurial marketing student based out of California Polytechnic State University San Luis Obispo. Background market research and empirical measurements were taken in order to confirm that this would be a marketable product worth designing. Then previous solutions were researched in order to identity weaknesses and strengths. After rigorous research, it was determined that a passive cooling system, in which channels directed airflow to the computer fan would be the best system in terms of functionality, performance, and cost. A …

Design And Simulation Of Passive Thermal Management System For Lithium-Ion Battery Packs On An Unmanned Ground Vehicle, Kevin Kenneth Parsons

Master's Theses

The transient thermal response of a 15-cell, 48 volt, lithium-ion battery pack for an unmanned ground vehicle was simulated with ANSYS Fluent. Heat generation rates and specific heat capacity of a single cell were experimentally measured and used as input to the thermal model. A heat generation load was applied to each battery and natural convection film boundary conditions were applied to the exterior of the enclosure. The buoyancy-driven natural convection inside the enclosure was modeled along with the radiation heat transfer between internal components. The maximum temperature of the batteries reached 65.6 °C after 630 seconds of usage …

Silicon Wafer Temperature Distribution, Daniel Gonzalez, Nathan Jones, Dylan Justice

Mechanical Engineering

Applied Materials is a global company that designs equipment for use in the semiconductor manufacturing industry. The scope of this project covers process chambers used for depositing thin chemical films onto silicon wafers. These processes must take place in particularly specific environments– including extremely low pressures and high temperatures. One challenge engineers face when designing these processes is carefully controlling the thermal behavior of silicon wafers. Typically, behavior is predicted using time consuming and computationally expensive CFD simulations. We have been asked to address this issue with a simpler, faster model which will allow engineers to reduce the total number …

Hepa Filter Evaluation Furnace Control Unit, Matt Gainer, Marc Goupil, Andrew Woolrich

Mechanical Engineering

No abstract provided.

Thermal Vacuum Integration For Cal Poly's Space Environments Laboratory, Chelsea Barackman, Steven Jackowski

Aerospace Engineering

The purpose of the senior project is to construct a thermal vacuum by utilizing a preexisting vacuum chamber in the Space Environments Lab, and a donated Advanced Thermal Sciences (ATS) chiller. While a thermal vacuum is already available on campus, building one for the Space Environments Lab would grant undergraduates access to the equipment, allowing a much better understanding of testing methods and procedures in use by the aerospace industry. This paper explains the design and analysis of the thermal vacuum (T-VAC) project as well as the operation and procedures required for the ATS chiller and fill/drain tank. The thermal …