Heat Transfer, Combustion Commons^™

Analysis Of Bio-Alcohols With Mie-Scattering And Ltc For Lowered Emissions In Pcci, Cesar E. Carapia

College of Graduate Studies: Theses & Dissertations

An investigation was conducted on the optimal engine parameters for facilitating lower NOX and soot emissions of PCCI combustion with either ethanol or n-butanol. The PFI fuels selected were tested at loads of 3, 4, and 5 Bar IMEP for a total of 28 total combustion tests with variations made to the EGR% and boost pressure for each test in order to find the optimal emissions strategy. A Mie-scattering spray fuel analysis was also conducted on the three fuels to gain insight on their influence on combustion/emissions characteristics. It was found that ethanol had a greater average Sauter Mean Diameter …

Hybridization From Guest-Host Interactions Reduces The Thermal Conductivity Of Metal-Organic Frameworks, Mallory E. Decoster, Hasan Babaei, Sangeun S. Jung, Zeinab M. Hassan, John T. Gaskins, Ashutosh Giri, Emma M. Tiernan, John A. Tomko, Helmut Baumgart, Pamela M. Norris, Alan J.H. Mcgaughey, Christopher E. Wilmer, Engelbert Redel, Gaurav Giri, Patrick E. Hopkins

Electrical & Computer Engineering Faculty Publications

We experimentally and theoretically investigate the thermal conductivity and mechanical properties of polycrystalline HKUST-1 metal–organic frameworks (MOFs) infiltrated with three guest molecules: tetracyanoquinodimethane (TCNQ), 2,3,5,6-tetrafluoro-7,7,8,8-tetracyanoquinodimethane (F4-TCNQ), and (cyclohexane-1,4-diylidene)dimalononitrile (H4-TCNQ). This allows for modification of the interaction strength between the guest and host, presenting an opportunity to study the fundamental atomic scale mechanisms of how guest molecules impact the thermal conductivity of large unit cell porous crystals. The thermal conductivities of the guest@MOF systems decrease significantly, by on average a factor of 4, for all infiltrated samples as compared to the uninfiltrated, pristine HKUST-1. This reduction in thermal conductivity goes in …

Numerical Investigation On The Effect Of Spectral Radiative Heat Transfer Within An Ablative Material, Raghava S. C. Davuluri, Rui Fu, Kaveh A. Tagavi, Alexandre Martin

Mechanical Engineering Faculty Publications

The spectral radiative heat flux could impact the material response. In order to evaluate it, a coupling scheme between KATS - MR and P1 approximation model of radiation transfer equation (RTE) is constructed and used. A Band model is developed that divides the spectral domain into small bands of unequal widths. Two verification studies are conducted: one by comparing the simulation computed by the Band model with pure conduction results and the other by comparing with similar models of RTE. The comparative results from the verification studies indicate that the Band model is computationally efficient and can be used to …

Droplet-Based Fuel Property Measurements, Wanjun Dang

LSU Doctoral Dissertations

Ongoing work to find renewable biofuels to function as drop-in replacements or blending components with gasoline has identified a large number of fuel candidates. Given the vast number of potential biomass-derived fuel molecules and limited sample sizes, screening tools are required to down-select candidate fuels having desired physical properties to ensure good engine performance. This work investigates approaches for rapid screening of candidate fuels using micro-liter sample sizes targeting four properties -- surface tension, viscosity, heat of vaporization (HOV), and vapor pressure. Measurement techniques for fuel properties are developed based on unit phenomena for liquid fuel droplets including droplet oscillation …

Deep Learning Strategies For Pool Boiling Heat Flux Prediction Using Image Sequences, Connor Heo

Graduate Theses and Dissertations

The understanding of bubble dynamics during boiling is critical to the design of advanced heater surfaces to improve the boiling heat transfer. The stochastic bubble nucleation, growth, and coalescence processes have made it challenging to obtain mechanistic models that can predict boiling heat flux based on the bubble dynamics. Traditional boiling image analysis relies on the extraction of the dominant physical quantities from the images and is thus limited to the existing knowledge of these quantities. Recently, machine-learning-aided analysis has shown success in boiling crisis detection, heat flux prediction, real-time image analysis, etc., whereas most of the existing studies are …

Global 3d Radiation Hydrodynamic Simulations Of Proto-Jupiter’S Convective Envelope, Zhaohuan Zhu, Yan-Fei Jiang, Hans Baehr, Andrew N. Youdin, Philip J. Armitage, Rebecca G. Martin

Physics & Astronomy Faculty Research

The core accretion model of giant planet formation has been challenged by the discovery of recycling flows between the planetary envelope and the disc that can slow or stall envelope accretion. We carry out 3D radiation hydrodynamic simulations with an updated opacity compilation to model the proto-Jupiter’s envelope. To isolate the 3D effects of convection and recycling, we simulate both isolated spherical envelopes and envelopes embedded in discs. The envelopes are heated at given rates to achieve steady states, enabling comparisons with 1D models. We vary envelope properties to obtain both radiative and convective solutions. Using a passive scalar, we …

Creation Of A Cip Method For The Heat Exchangers At Rolls-Royce, Melanie Howe, Austin Williams, Caroline Dempsey, Bethany Fralick

Journal of the South Carolina Academy of Science

Rolls-Royce produces various engines which must be tested prior to their distribution to ensure a high-quality product. The manufacturing plant contains four test cells where the engines can be subjected to high levels of torque and extreme temperatures. A heat exchanger is necessary in this testing system and over time, unwanted waste accumulates on the system’s plates. The team is tasked with developing and implementing a system mounted on a mobile cart which can provide data to determine whether the plates need to be cleaned. For this cleaning system to work, it must fully saturate the heat exchanger in cleaning …

Fully Coupled Internal Radiative Heat Transfer For The 3d Material Response Of Heat Shield, Raghava S. C. Davuluri, Rui Fu, Kaveh A. Tagavi, Alexandre Martin

Mechanical Engineering Faculty Publications

The radiative transfer equation (RTE) is strongly coupled to the material response code KATS. A P-1 approximation model of RTE is used to account for radiation heat transfer within the material. First, the verification of the RTE model is performed by comparing the numerical and analytical solutions. Next, the coupling scheme is validated by comparing the temperature profiles of pure conduction and conduction coupled with radiative emission. The validation study is conducted on Marschall et al. cases (radiant heating, arc-jet heating, and space shuttle entry), 3D Block, 2D IsoQ sample, and Stardust Return Capsule. The validation results agree well for …

Investigation Of Two-Phase Flow Phenomena In Rotating Paper Dryer To Achieve Effective Heat Transfer With Low Energy Consumption, Hamed Abdul Majeed

LSU New Orleans Theses and Dissertations

The paper industry provides important consumer products comprised of paper, tissue, paper board, and pulping. The papermaking process requires a lot of energy, in the form of steam, to dry the paper web in rotating dryers. As steam condenses inside the dryers by releasing heat to the dryer walls, the condensate is removed using either stationary or rotary siphons. Since the condensate is usually at a saturated state, part of the condensate flashes into vapor during the extraction process and becomes difficult to extract. Thus, additional blow-through steam is used to push the condensate out. Since this blow-through steam is …

An Investigation Of The Effects Of Variable Magnetic Field Gradients On Soot And Co Emissions From Non-Premixed Hydrocarbon Flames, Edison Ekperechukwu Chukwuemeka

LSU Doctoral Dissertations

The interaction of the paramagnetic species in a combustion process with the mag- netic field placed in the vicinity of non-premixed flames affects the characteristics of the non-premixed flames - flame height and flame lift-off height. However, the effect of this magnetic interaction on the pollutants generated by the flame is unknown.

In general, pollutant formation is promoted in most combustion systems due to in- complete combustion of the hydrocarbon due to improper mixing. Since paramagnetic combustion species such as O2, O, OH, etc interacts with magnetic fields and possess a preferential motion direction, imposing magnetic field on non-premixed flames …

Relationship Between Thermal Conductivity And Free Electrons In Metal, Yansong Liu

Senior Theses

An experiment was designed and conducted to explore the relationship between thermal conductivity with free electrons in metal. In the experiment, copper, iron, aluminum, and titanium rods with close diameters were used to carry out the experiment. Each rod was heated up by a heat unit at one end while cooled on the other end with a heat sink to maintain a steady state. DC current was applied to rods in the direction along, as well as against, the heat flow. Thermal conductivities were measured in these two situations for each rod. Results showed electrons do dominate thermal flow inside …

Numerical Reconstruction Of Spalled Particle Trajectories In An Arc-Jet Environment, Raghava S. C. Davuluri, Sean C. C. Bailey, Kaveh A. Tagavi, Alexandre Martin

Mechanical Engineering Faculty Publications

To evaluate the effects of spallation on ablative material, it is necessary to evaluate the mass loss. To do so, a Lagrangian particle trajectory code is used to reconstruct trajectories that match the experimental data for all kinematic parameters. The results from spallation experiments conducted at the NASA HYMETS facility over a wedge sample were used. A data-driven adaptive methodology was used to adapts the ejection parameters until the numerical trajectory matches the experimental data. The preliminary reconstruction results show that the size of the particles seemed to be correlated with the location of the ejection event. The size of …

Multiscale Investigation Of Dropwise Condensation On A Smooth Hydrophilic Surface, Shahab Bayani Ahangar

Dissertations, Master's Theses and Master's Reports

The objective of this work is to identify the fundamental mechanism of dropwise condensation on a smooth solid surface by probing the solid-vapor interface during phase-change to evaluate the existence and structure of the thin film and the initial nucleus that develop during condensation. In this work, an automated Surface Plasmon Resonance imaging (SPRi) instrument with the ability to perform imaging in intensity modulation and angular modulation is developed. The SPRi instrument is used to probe (in three dimensions) the adsorbed film that forms on the substrate during dropwise condensation. SPRi with a lateral resolution of ~ 4-10 μm, thickness …

Effect Of Heat Treatment On Microstructure And Hardness Of A Worn Rail Repaired Using Laser Powder Deposition, Ershad Mortazavian, Zhiyong Wang, Hualiang Teng

Mechanical Engineering Faculty Research

The frequent replacement of worn rails on tracks brings an immense economic burden on the railroad industry, and also causes significant interruptions to railroad operation. Restoration of worn rails via laser powder deposition (LPD) can considerably reduce the associated maintenance costs. This study was focused on the use of LPD to repair the worn profile of a standard U.S. rail. The microstructure of the 304L stainless steel deposits with a minimum hardness of 85 HRB was composed of austenite, δ-ferrite, and sigma. Micropores were dispersed throughout the deposit, and microcracks were found at the rail-deposition interface. The pearlitic rail substrate …

Thermo-Fluid Characterizations Of The Powder-Bed Fusion Additive Manufacturing Processes Using Laser And Electron Beam, M Shafiqur Rahman

LSU New Orleans Theses and Dissertations

The powder-bed fusion (PBF) process is a subdivision of Additive Manufacturing (AM) technology where a heat source at a controlled speed selectively fuses regions of a powder-bed material to form three-dimensional (3-D) parts. Two of the most effective PBF processes are selective laser melting (SLM) and electron beam additive manufacturing (EBAM), which can fabricate full-density metallic parts in a layer-by-layer fashion. In this study, thermal behavior and melt-pool dynamics in the PBF process are investigated by developing 3-D multiphysics-based thermo-fluid models for both SLM and EBAM, containing Ti-6Al-4V alloy as a powder-bed material. The laser and electron beams are modeled …

Potential Energy Generation From Agricultural Residue In Indonesia, Adrian Rizqi Irhamna

International Programs

Indonesia has great potential of biomass sources from their agricultural residue, which can potentially be used for alternative energy generation. This preliminary research explores the most suitable technology for energy generation from agricultural residue and its challenge for application in Indonesia. The study showed that biomass utilization via the direct combustion process is recommended for energy generation. It is also reported that the pretreatment process of drying and washing, are required to increase the fuel quality and plant efficiency.

Cooking Systems Using Aluminum Foam, Ryan Tetsuo Mizukami

Physics

In developing countries, the use of wood burning fires for cooking is cause for illness and death. With this in mind, research was conducted to develop a solar cooking device capable of cooking of soup within 15 mins in order to reduce the negative impacts of cooking with wood. Current methods of solar-based cooking, such as solar concentrators and solar tube ovens, are impractical. A small solar panel is a cost-effective way to produce energy but will not produce enough power to cook within a reasonable amount of time. Even if it is assumed that all of the energy produced …

Study Of Heat And Momentum Transfer To Colloidal Suspensions In Annular Closed Conduit Flow, Sadik Shoaib

Student Works (2020-2029)

With the advancement of science and the rapid growth of industries and the improved lifestyles of people, energy consumption has been increasing. Whereas the exploration of energy remained at a slower pace and the energy reservoirs are extinguishing at a faster rate. High energy consumption is also encouraging environmental pollution and global warming. Considering all these issues, scientists and engineers are desperately exploring highly efficient heat exchangers for the conservation of energy and minimize its losses. The present research has focused on obtaining highly efficient heat exchangers. Lots of research have performed on the improvement of heat exchanger materials, alteration …

Synthesis Of Eco-Friendly Nanofluids For Enhancement Of Heat Transfer And Application In Different Flow Configuration Passages, Khan Asif

Student Works (2020-2029)

Since the invention of the heat exchangers, the working fluids such as water, ethyl glycol, oil and many others were used, however, they reveal relatively low thermal conductivity. Eco-friendly nanofluids and the cost-effective annular heat exchangers were introduced in this research to overcome the problem. In the present work, heat transfer coefficient and friction loss analyses of (TiO2 and GNP) water-based nanofluids were compared with DI-water flowing in annular conduit under turbulent flow regime. The nanoparticle weight concentrations of 0.1, 0.075, 0.05 and 0.025 wt.% were prepared by using a simple two-step method. The DI-water simulations were conducted by using …

Enhancement Of Phase Change Material Sorbitol By Nanoparticle Inclusion For Improving Thermal Energy Storage Capabilities, Joshua Kasitz

Mechanical Engineering Undergraduate Honors Theses

Thermal management of electronic devices has become an increasingly vital field of study with the rapid miniaturization of many key electrical components. With the significant improvement of semiconductor manufacturing and intensified focus on interconnects, electronic devices have decreased in size at an incredible rate. Decreasing spatial requirements is essential to improving device capabilities as the electronic system is able to incorporate more components. Currently, electronic systems are drastically limited by the capabilities of their cooling mechanisms. Smaller devices lead to large increases in the energy density of the system and require more powerful cooling systems to maintain proper component operating …

Computational Analysis Of A New Planar Mixing Layer Flame Configuration To Study Soot Inception, Carmen Ciardiello

Honors Scholar Theses

The production of soot is omnipresent in society today. Soot is the product of many of the combustion processes that provide the bulk of the usable energy throughout the world. Furthermore, soot particulate poses a great danger to both the environment and all forms of life on Earth. It has proven to pollute ecosystems, foster health problems for human beings, and degrade air quality [1].

These dangers make studying and understanding soot particulate paramount for improving the quality of life. Thus, this study introduces a new flame configuration for studying soot inception. Presently, various common flame configurations have been found …

Thermodynamic Model Of Co2 Deposition In Cold Climates, Sandra K. S. Boetcher, Ted Von Hippel, Matthew J. Traum

Publications

A thermodynamic model, borrowing ideas from psychrometric principles, of a cryogenic direct-air CO2-capture system utilizing a precooler is used to estimate the optimal CO2 removal fraction to minimize energy input per tonne of CO2. Energy costs to operate the system scale almost linearly with the temperature drop between the ingested air and the cryogenic desublimation temperature of CO2, driving siting to the coldest accessible locations. System performance in three Arctic/Antarctic regions where the proposed system can potentially be located is analyzed. Colder ambient temperatures provide colder system input air temperature yielding lower CO2 removal energy requirements. A case is also …

Computational Studies Of Thermal Properties And Desalination Performance Of Low-Dimensional Materials, Yang Hong

Department of Chemistry: Dissertations, Theses, and Student Research

During the last 30 years, microelectronic devices have been continuously designed and developed with smaller size and yet more functionalities. Today, hundreds of millions of transistors and complementary metal-oxide-semiconductor cells can be designed and integrated on a single microchip through 3D packaging and chip stacking technology. A large amount of heat will be generated in a limited space during the operation of microchips. Moreover, there is a high possibility of hot spots due to non-uniform integrated circuit design patterns as some core parts of a microchip work harder than other memory parts. This issue becomes acute as stacked microchips get …

Energy Transformation And Conservation Investigation, Mike Jackson, Holly Haney

High School Lesson Plans

Students will use a thermoelectric generator module to analyze the relationship between thermal and electrical energies. Using data collection sensors and analysis software, students will investigate the relationship between the temperature gradient across a thermoelectric generator module and the resulting electrical potential. Students will then use their data and analysis to solve problems relating to waste thermal energy in electrical systems and communicate their work to their peers and teacher.

Examination Of Flow Dynamics And Passive Cooling In An Ultra Compact Combustor, Tylor C. Rathsack

Theses and Dissertations

The Ultra Compact Combustor (UCC) promises to greatly reduce the size of a gas turbine engine’s combustor by altering the manner in which fuel is burnt. Differing from the common axial flow combustor, the UCC utilizes a rotating flow, coaxial to the engine’s primary axis, in an outboard circumferential cavity as the primary combustion zone. The present study investigates two key UCC facets required to further this combustor design. The first area of investigation is cooling of the Hybrid Guide Vane (HGV). This UCC specific hardware acts as a combustor center body that alters the exit flow angle and acts …

Numerical Investigation Of Inclination On The Thermal Performance Of Porous Fin Heatsink Using Pseudospectral Collocation Method, George Oguntala, Gbeminiyi Sobamowo, Raed Abd-Alhameed, James Noras

Karbala International Journal of Modern Science

Numerical investigation of inclination effect on the thermal performance of a porous fin heat sink is presented. The developed thermal model is solved using pseudo-spectral collocation method (PSCM). Parametric studies are carried out using PSCM, and the thermal characterization of heat sink with the inclined porous fin of rectangular geometry is presented. Results show that heat sink of inclined porous fin exhibits higher thermal performance than heat sink of vertical porous fin operating under the same thermal conditions with the same geometrical configurations. Performance of inclined or tilted fin increases with decrease in length-thickness aspect ratio. However, increase in the …

What Can I Do As A Student To Make A Positive Impact On The Environment?, Tammy Guthrie, Greg Herzig, Kathy Prophet, Cassie Kautzer

Middle School Lesson Plans

Students discover ways they can make a positive impact on the environment.

Thermal Removal Of Carbon Dioxide From The Atmosphere: Energy Requirements And Scaling Issues, Ted Von Hippel

Publications

I conduct a systems-level study of direct air capture of CO2 using techniques from thermal physics. This system relies on a combination of an efficient heat exchanger, radiative cooling, and refrigeration, all at industrial scale and operated in environments at low ambient temperatures. While technological developments will be required for such a system to operate efficiently, those developments rest on a long history of refrigeration expertise and technology, and they can be developed and tested at modest scale. I estimate that the energy required to remove CO2 via this approach is comparable to direct air capture by other techniques. The …

Evaluation And Enhancement Of Clean Energy Systems: Analytical, Computational And Experimental Study Of Solar And Nuclear Cycles, Nima Fathi

Mechanical Engineering ETDs

Clean (and specifically renewable) energy is steadily improving its global share. However, finite availability of fossil fuels and the growing effects of climate change make it an urgent priority to convince the industry and governments to incentivize investment in the renewable energy field and to make it more attractive by decreasing the capital cost. Until recently, uncertainties in funding limited renewable energy development, especially in the US. That limitation has been one of the barriers to progress. Another limitation of many renewable energy systems is the variability in their output, which makes them unsuitable for baseline power production. Therefore, fossil …

Solvent Degradation And Emissions From A 0.7mwe Pilot Co2 Capture System With Two-Stage Stripping, Jesse Thompson, Heather Nikolic, Megan Combs, Saloni Bhatnagar, Jonathan Pelgen, Keemia Abad, Kunlei Liu

Center for Applied Energy Research Faculty and Staff Publications

The UKy-CAER team successfully tested an advanced 0.7 MWe post-combustion CO₂ capture system on a coal-fired power plant using a heat integration process combined with two-stage stripping to enhance the CO₂ absorber performance. One of the unique feature of the UKy-CAER integrated process is a two-stage stripping unit for solvent regeneration. The secondary stripper is empowered by the heat rejection from a conventional steam-heated (primary) stripper. The secondary stripper outlet stream at the commercial scale can be used as boiler secondary combustion air, consequently enriching the flue gas with CO₂, resulting in less energy penalty required …