Heat Transfer, Combustion Commons^™

Relationship Between Thermal Conductivity And Free Electrons In Metal, Yansong Liu

Senior Theses

An experiment was designed and conducted to explore the relationship between thermal conductivity with free electrons in metal. In the experiment, copper, iron, aluminum, and titanium rods with close diameters were used to carry out the experiment. Each rod was heated up by a heat unit at one end while cooled on the other end with a heat sink to maintain a steady state. DC current was applied to rods in the direction along, as well as against, the heat flow. Thermal conductivities were measured in these two situations for each rod. Results showed electrons do dominate thermal flow inside …

Thermal Control Development Of A Proton Exchange Membrane Fuel Cell System, Ola Mohammed Taha Al-Shalash

Mechanical Engineering Theses

A fuel cell is an electrochemical energy conversion device that uses fuel to generate electricity. It basically converts the chemical energy of reactants directly into electricity without combustion. In a Proton Exchange Membrane Fuel Cell (PEMFC), the reactants, hydrogen and oxygen, are fed into the two electrodes, anode and cathode, respectively. A reaction takes place at each electrode and produces electricity, as well as water, and heat as the by-products. In order to maximize performance of a fuel cell, many factors can be considered for tuning and control. Temperature management is one of these factors.

A thermal-fluid model of a …

Cfd Modelling Of Multiphase Flow In Static Mixer, Silverrajan Viknesvaran

Student Works (2020-2029)

Modelling of Multiphase flow through a Kenics static mixer were presented in this paper. Multiphase mixing is a challenging process in industries such as pharmaceutical, food and petroleum since two-different phases can be immiscible towards each other. Stirred tank mixing is the most common method used in industries. However, this type of method costs a lot in terms of energy and manpower specially when mixing immiscible liquids. Hence, The Kenics Static Mixer could be a good solution for multiphase mixing when its correctly configured and studied. Two phases used in this paper were aqueous solution: refined CMC as continuous phase …

Study Of Heat Transfer And Friction Loss Of Nanofluid Suspension Flow In Square Pipe Heat Exchanger, Krishnan Jayprasanth

Student Works (2020-2029)

An experimentational analysis was done to evaluate heat transfer features of graphene oxide (GO) nanofluid inside the cross section of square cross tube that was exposed to a uniform constant heat flux of the test segments. Lately huge figures of researches have been are proceeded out to examine the outcome of nanofluid in augmentation of the heat transfer rate in numerous heat exchangers particularly using hummer method to attain GO. In this case, advanced hummer method was used to obtain GO and further analyses the effect of the nanofluids. The viscosity and thermal conductivity for the (GO) nanofluids at the …

Investigations Of Air-Water Multiphase Flow In Tubes: Computational Fluid Dynamics, Wei Hong Goo

Student Works (2020-2029)

Mixing is a very crucial process in many industries, such as food processing industry, minerals processing industry, petrochemicals and refining industry, pulp and paper industry, polymer industry, pharmaceuticals industry and many more. There are different types of mixing, such as liquid-gas mixing, liquid-liquid mixing, solid-liquid mixing and many more. The definition of multiphase flow is the simultaneous flow of materials with multiple thermodynamic phases. A lot of process industries require multiphase flows during operation. Bubbly flow is defined as the flow of liquids that contains dispersed gas bubbles. One of the main applications of multiphases flows and bubbly flows is …

Study Of Heat Transfer And Friction Loss Of Nanofluid Suspension Flow In Circular Pipe Heat Exchanger, Ramadas Sandru

Student Works (2020-2029)

This stated experiment focused on the study of convective heat transfer and friction loss in a circular flow passage for Graphene oxide-based nanofluids which are consist of Graphene Oxide/Distilled water with their different wt. % concentrations. These GO/DW based nanofluids where been prepared by using a facile two-step method, while the GO particles were synthesized by a modified hummer method. Four different (0.025, 0.05, 0.075, and 0.1 wt. %) were produced by dispersing graphene particles in distilled water under high probe sonication. The GO/DW based nanofluids flowing in a horizontal shell and tube heat exchanger counter flow under turbulent flow …

What Difference Does A Catalyst Make?, Tammy Guthrie, Mike Jackson, Holly Haney

High School Lesson Plans

Students will use different catalysts for the decomposition of Hydrogen Peroxide, to determine if different catalysts affect the energy that is generated during the reaction.

Study Of Heat And Momentum Transfer To Colloidal Suspensions In Annular Closed Conduit Flow, Sadik Shoaib

Student Works (2020-2029)

With the advancement of science and the rapid growth of industries and the improved lifestyles of people, energy consumption has been increasing. Whereas the exploration of energy remained at a slower pace and the energy reservoirs are extinguishing at a faster rate. High energy consumption is also encouraging environmental pollution and global warming. Considering all these issues, scientists and engineers are desperately exploring highly efficient heat exchangers for the conservation of energy and minimize its losses. The present research has focused on obtaining highly efficient heat exchangers. Lots of research have performed on the improvement of heat exchanger materials, alteration …

Synthesis Of Eco-Friendly Nanofluids For Enhancement Of Heat Transfer And Application In Different Flow Configuration Passages, Khan Asif

Student Works (2020-2029)

Since the invention of the heat exchangers, the working fluids such as water, ethyl glycol, oil and many others were used, however, they reveal relatively low thermal conductivity. Eco-friendly nanofluids and the cost-effective annular heat exchangers were introduced in this research to overcome the problem. In the present work, heat transfer coefficient and friction loss analyses of (TiO2 and GNP) water-based nanofluids were compared with DI-water flowing in annular conduit under turbulent flow regime. The nanoparticle weight concentrations of 0.1, 0.075, 0.05 and 0.025 wt.% were prepared by using a simple two-step method. The DI-water simulations were conducted by using …

Energy Conservation And Heat Transfer Enhancement For Mixed Convection On The Vertical Galvanizing Furnace, Dan Mei, Yuzheng Zhu, Xuemei Xu, Futang Xing

Mechanical & Aerospace Engineering Faculty Publications

The alloying temperature is an important parameter that affects the properties of galvanized products. The objective of this study is to explore the mechanism of conjugate mixed convection in the vertical galvanizing furnace and propose a novel energy conservation method to improve the soaking zone temperature based on the flow pattern and heat transfer characteristics. Herein, the present study applied the k-ε two-equation turbulence model to enclose the Navier-Stokes fluid dynamic and energy conservation equations, and the temperature distributions of the steel plate and air-flow field in the furnace were obtained for six Richardson numbers between 1.91 ⋅ 10^{5 …}

Electrification Of Domestic Hot Water To Aid The Integration Of Renewable Energy In The California Grid, Alejandro Cervantes

Cal Poly Humboldt theses and projects

Water heating in residential buildings, also known as domestic hot water (DHW), is the third largest use of energy after appliances and space conditioning. About 90% of the residential buildings in the state use natural gas fueled water heaters, 6% use electricity, and a small percent use liquefied petroleum gas (LPG) or solar water heaters. The current energy use associated with residential water heating is small relative to the total amount of energy consumption in the residential building sector, but it is still a contributor of greenhouse gas (GHG) emissions. Improving hot water systems can be beneficial for bill customer …

Zips Precious Plastics: Plastic Extruder, Patrick Cole

Williams Honors College, Honors Research Projects

This project's goal was to design and build an affordable desktop filament extruder that can precisely and consistently extrude filament to a certain tolerance acceptable for 3D printers using wasted printing material. The group is partnering with an on campus organization focusing on engineering applications for sustainable futures. Zips Precious Plastics is a student run design group that intends to bring an innovation space on campus to help educate students about the importance of a closed looped system within plastic manufacturing.

Energy Transformation And Conservation Investigation, Mike Jackson, Holly Haney

High School Lesson Plans

Students will use a thermoelectric generator module to analyze the relationship between thermal and electrical energies. Using data collection sensors and analysis software, students will investigate the relationship between the temperature gradient across a thermoelectric generator module and the resulting electrical potential. Students will then use their data and analysis to solve problems relating to waste thermal energy in electrical systems and communicate their work to their peers and teacher.

Biomethane Production From Distillery Wastewater, Zachary Christman

Department of Agronomy and Horticulture: Dissertations, Theses, and Student Research

Distillery wastewater treatment is a great ecological problem, for example, India produces 2.7 billion liters of alcohol that results in 40 billion liters of wastewater. However, this material can be seen as a resource since 11 million cubic meters of biogas at 60% methane could be produced in addition to cleaning the water. The distillery has two options of what to do with the biogas. The first is to use the biogas to fuel the distillery making the production plant more energy efficient and removing some of the need to buy natural gas. The other is to upgrade the biogas …

Experimental Investigation Of The Manufacture Of Tunable Graphene Oxide Filter Membranes Using Intense Pulse Light, Joshua H Kotter

Electronic Theses and Dissertations

Reduced graphene oxide is a thin, strong, and inexpensive material with a channel and pore structure that make it a promising candidate for a filtration material. Reduced graphene oxide has been produced and tested in the laboratory, but a lack of scalable manufacturing techniques have limited its commercial use.

This thesis has shown that graphene oxide can be rapidly manufactured with an industrially scalable flash reduction process. The flash reduction process uses 0.58 millisecond pulses from a xenon lamp to reduce the graphene oxide film in less than a minute. Results for partially reduced graphene oxide membranes tuned by the …

Examination Of Flow Dynamics And Passive Cooling In An Ultra Compact Combustor, Tylor C. Rathsack

Theses and Dissertations

The Ultra Compact Combustor (UCC) promises to greatly reduce the size of a gas turbine engine’s combustor by altering the manner in which fuel is burnt. Differing from the common axial flow combustor, the UCC utilizes a rotating flow, coaxial to the engine’s primary axis, in an outboard circumferential cavity as the primary combustion zone. The present study investigates two key UCC facets required to further this combustor design. The first area of investigation is cooling of the Hybrid Guide Vane (HGV). This UCC specific hardware acts as a combustor center body that alters the exit flow angle and acts …

Exergetic Relationship Between The Thermal Properties Of Direct Contact Membrane Distillation, D. Perdue, L. Chen, L. Schaefer

Publications

Direct contact membrane distillation (DCMD) is a process that has shown promise within the field of desalination due to its less energy intensive methods and widespread applications. DCMD is a thermally driven microfiltration separation process that operates on the principle of vapor–liquid equilibrium conditions where heat and mass transfer occur simultaneously. Fundamentally, DCMD is based on a porous hydrophobic membrane separating the hot solution (feed) from the cold solution (permeate) where desalinated water condenses. The membrane interfacial temperatures determine the vapor pressure difference across the membrane. In this work, a direct simulation Monte Carlo analysis is employed to investigate how …

Improving The Delivered Specific Impulse Of Composite Rocket Propellant Through Alteration Of Chemical Composition: Methodology And Parameters For Characterization Of Propellant And Validation Of Simulation Software Common To The Amateur Rocketry Community, Isaac O'Brien, Austin Ryan

Williams Honors College, Honors Research Projects

In this study, two solid composite rocket propellants were designed utilizing ProPEP, a rocket propellant formulation software common in the amateur and hobby rocketry communities. The two propellants were designed to optimize specific impulse relative to a literature propellant designed by 1020 Research Labs. The literature propellant was also tested in order to validate the design of experiment as well as the mixing and testing procedures. All three propellants, which includes the literature propellant RCS-P, and the two novel propellants AKR-P1 and AKR-P2 were characterized with static tests. The results of the static tests provide data on propellant performance and …

Literature Survey Of Wet-Waste And Hydrothermal Carbonization System: A Comparative Evaluation, Ramat Olaide Yusuf

Dissertations and Theses

This thesis describes the process of Hydrothermal carbonization and a comparative assessment on recent work done on the process using different feedstocks such as Raw Apple (RA), Apple chip pomace (ACP), apple juice pomace (AJP), grape pomace (GP), macadamia nut-shell (MNS), Sewage Sludge (SS), Poultry Litter (PL) and Grape Marc (GM). The data obtained from the literature survey was compared with the data obtained by the CCL team on the SWPS gasifier (HTC of poultry litter) to obtain how carbon conversion efficiency, syngas composition, thermal efficiency, char production rate, gas production rate and energy utilization vary with carbonization process conditions, …

Reduction Of Nox Emissions In A Single Cylinder Diesel Engine Using Sncr With In-Cylinder Injection Of Aqueous Urea, Anthony Timpanaro

UNF Graduate Theses and Dissertations

The subject of this study is the effect of in-cylinder selective non-catalytic reduction (SNCR) of NO_x emissions in diesel exhaust gas by means of direct injection of aqueous urea ((NH₂)₂CO) into the combustion chamber. A single cylinder diesel test engine was modified to accept an electronically controlled secondary common rail injection system to deliver the aqueous urea directly into the cylinder during engine operation.

Direct in-cylinder injection was chosen in order to ensure precise delivery of the reducing agent without the risk of any premature reactions taking place. Unlike direct in-cylinder injection of neat water, …

Effect Of Aerogel On The Thermal Performance Of Corrugated Composite Sandwich Structures, Jacob Dillon Chess

Master's Theses

Current insulation solutions across multiple industries, especially the commercial sector, can be bulky and ineffective when considering their volume. Aerogels are excellent insulators, exhibiting low thermal conductivities and low densities with a porosity of around 95%. Such characteristics make aerogels effective in decreasing conductive heat transfer within a solid. These requirements are crucial for aerospace and spaceflight applications, where sensitive components exist among extreme temperature environments. When implemented into insulation applications, aerogel can perform better than existing technology while using less material, which limits the amount of volume allocated for insulation. The application of these materials into composites can result …

Low Temperature Desiccants In Atmospheric Water Generation., Sunil Gupta

Electronic Theses and Dissertations

Surging global water demand as well as changes to weather patterns and over exploitation of natural water sources, such as ground water, has made potable water a critical resource in many parts of the World already – one rapidly heading towards a crisis situation. Desalination has been adopted as a solution – this is however energy intensive and impractical for most of the developing countries - those most in need of water. A renewable source of energy is solar thermal and solar photovoltaic. A plentiful source of water is the humidity in the atmosphere. This research is to push the …

Thermophotovoltaic Devices: Combustion Chamber Optimization And Modelling To Maximize Fuel Efficiency, Arnold Chris Toppo, Ernesto Marinero, Zhaxylyk Kudyshev

The Summer Undergraduate Research Fellowship (SURF) Symposium

Currently, 110 billion cubic meters of natural gas (primarily methane), a potent greenhouse gas, are flared off for environmental and safety reasons. This process results in enough fuel to provide the combined natural gas consumption of Germany and France. The research team developed a thermophotovoltaic device to convert thermal energy to electricity at a high efficiency using proprietary emitters and combustion system. With the current focus being fuel efficiency and the combustion process, the assembly was simulated using ANSYS Fluent modelling software and the following parameters were optimized: air/fuel ratios, flow rates, and inlet sizes. Simultaneously the heat transfer across …

What Can I Do As A Student To Make A Positive Impact On The Environment?, Tammy Guthrie, Greg Herzig, Kathy Prophet, Cassie Kautzer

Middle School Lesson Plans

Students discover ways they can make a positive impact on the environment.

Thermal Removal Of Carbon Dioxide From The Atmosphere: Energy Requirements And Scaling Issues, Ted Von Hippel

Publications

I conduct a systems-level study of direct air capture of CO2 using techniques from thermal physics. This system relies on a combination of an efficient heat exchanger, radiative cooling, and refrigeration, all at industrial scale and operated in environments at low ambient temperatures. While technological developments will be required for such a system to operate efficiently, those developments rest on a long history of refrigeration expertise and technology, and they can be developed and tested at modest scale. I estimate that the energy required to remove CO2 via this approach is comparable to direct air capture by other techniques. The …

NoX Formation In Light-Hydrocarbon, Premixed Flames, Robert T. Hughes

Theses and Dissertations--Mechanical and Aerospace Engineering

This study explores the reactions and related species of NO_x pollutants in methane flames in order to understand their production and consumption during the combustion process. To do this, several analytical simulations were run to explore the behavior of nitrogen species in the pre-flame, post- flame, and reaction layer regions. The results were then analyzed in order to identify all "steady-state" species in the flame as well as the determine all the unnecessary reactions and species that are not required to meet a defined accuracy. The reductions were then applied and proven to be viable.

Investigation On The Potential Of A Co2 Capture System, Downstream Of The Aftertreatment System For A Heavy-Duty Engine Application, Murchana Pathak

Dissertations, Master's Theses and Master's Reports

The transportation sector accounts for the second largest source of CO₂ emissions after power generation. New Corporate Average Fuel Economy (CAFE) regulations are focusing on improving energy through reduced fuel consumption and greenhouse gas emissions. This work investigates the potential of a CO₂ capture system downstream of an aftertreatment system for a heavy-duty engine application. Amine absorption has been described as one of the most effective ways to capture CO₂ from the exhaust for point sources. Therefore, using thermal-swing absorption process with potassium carbonate (K₂CO₃) as the absorbent liquid, a process was analyzed …

Investigation Of Combustion Characteristics Of A Heavy-Duty Diesel Engine Retrofitted To Natural Gas Spark Ignition Operation, Jinlong Liu

Graduate Theses, Dissertations, and Problem Reports (ETD)

The conversion of existing diesel engines to natural-gas spark ignition operation by adding a gas injector in the intake manifold for fuel delivery and replacing the diesel fuel injector with a spark plug to initiate and control the combustion process can reduce U.S. dependence on petroleum imports and curtail engine-out emissions. As the conventional diesel combustion chamber (i.e., flat head and bowl-in-piston) creates high turbulence, the engine can operate leaner, which would increase its efficiency and reduce emissions. However, natural gas combustion in such retrofitted engines presents differences compared to that in conventional spark ignited engines. Subsequently, the main goal …

Reduced Exhaust Emissions Through Blending N-Butanol With Ultra Low Sulfur Diesel And Synthetic Paraffinic Kerosene In Reactivity Controlled Compression Ignition Combustion, Remi Gaubert

College of Graduate Studies: Theses & Dissertations

Increasing restrictions on the emitted exhaust emissions in diesel engines are becoming a more challenging task than in previous years. An electronic common rail fuel injection system and a port fuel injection (PFI) system were developed for an experimental engine to research dual fuel combustion. The experimental research was conducted at 1500 rpm and 4, 5, and 6 bar indicated mean effective pressure (IMEP). n-Butanol was port fuel injected at a 60% by mass fraction coupled with direct injection (DI) of three fuels, including ultra-low sulfur diesel (ULSD RCCI), a 50-50 wt-% blend of ULSD and butanol (ULSD-Bu RCCI), and …

Modal Phonon Transport Across Interfaces By Non-Equilibrium Molecular Dynamics Simulation, Yang Zhong, Tianli Feng, Xiulin Ruan

The Summer Undergraduate Research Fellowship (SURF) Symposium

Phonons represent the quantization of lattice vibration, responsible for heat transfer in semiconductors and dielectrics. Phonon heat conduction across interfaces is crucially important for the thermal management of real-life devices such as smartphones, electric vehicles, and satellites. Although recent studies have broadly investigated spectral phonon contribution to lattice thermal conductivity, the mechanism of phonon modal transport across interfaces is still not well-understood. Previous models, including the acoustic mismatch model (AMM) and diffuse mismatch model (DMM), only consider elastic process while neglecting inelastic phonon contributions. Herein, we employ spectral Non-Equilibrium Molecular Dynamics Simulation (NEMD) to probe the temperature and heat flux …