Heat Transfer, Combustion Commons^™

Design Of An Experimental Solid Rocket Motor, Johnathan Bettes, Andrew Fuller

Williams Honors College, Honors Research Projects

This project utilizes mechanical and chemical principles to characterize propellant grains and to manufacture a custom nozzle to create experimental Solid Rocket Motors (SRMs) with a propellant called Angry Listerine. For the propellant grains, one major non-chemical factor that determines its thrust performance is the grain geometry, or the core of the grains for which hot gases flow through the propellant and out of the nozzle to further react with exposed chemical surfaces. The two kinds of grain geometries analyzed and tested in this report are called MoonBurner, an offset circular core, and Finocyl, a gear-shaped core. The nozzle for …

Propulsion Heat Analysis Nuclear Trajectory Optimization (Phantom), Ana Clecia Alves Almeida, Jonathan Davis, Ryan Dippolito

Williams Honors College, Honors Research Projects

Interplanetary Travel requirements necessitate the use of increasingly complex propulsion systems. Nuclear Thermal Propulsion (NTP) is a cutting-edge concept that holds immense potential for the future of space exploration. By utilizing nuclear fission to heat a propellant and generate thrust, NTP offers the potential for unprecedented efficiency, enabling faster interplanetary travel and extended mission capabilities. A nuclear thermal rocket engine is a type of propulsion system that utilizes the heat generated by a nuclear reactor to heat and expel a propellant, typically hydrogen, at high velocities to produce thrust. The engine consists of three main subsystems: the nuclear reactor, the …

Analysis Of Variations In Flow-Independent Liquid Jet-In-Crossflow Injections, Michael Scott

Honors Undergraduate Theses

Liquid fuel injection is a critical mechanism for the deliverance of liquid fuel in contemporary aircraft propulsion combustion systems due to its outsized influence in providing optimal combustion conditions and improving overall aircraft efficiency and performance. Despite this, these liquid jet in crossflow (LJIC) systems are highly variable due to conditions in the jet and the surrounding airflow, leading to variability in performance behavior and inconsistency in fuel mixing and combustion efficiency. This has prompted the introduction of solid pintile obstructions of novel designs to provide a more flow-independent fuel injection scheme and decrease variability of the jet properties against …

Investigations Of Performance And Emissions Of A Fischer-Tropsch Gtl Sustainable Aerospace Fuel With Lubricity Improver In A Compression Ignition Engine With Butanol Port Fuel Injection, James B. Willis

College of Graduate Studies: Theses & Dissertations

As there is increasing concern over emissions of traditional fossil fuels, as well as the future of continued reliance on this dwindling resource, it is becoming increasingly evident that alternative fuels are a necessity. This research investigates the use of a Fischer-Tropsch fuel from natural gas feedstocks, S8, in an internal combustion research engine with a common rail fuel injection system. This synthetic kerosene fuel has a high DCN of 62, indicating high affinity to autoignition compared to conventional pump diesel (ULSD) at 48 DCN. However, due to the process by which it is produced, this fuel lacks the necessary …

Fluid Flow And Thermal Performance Investigation Of Twisted Elliptical Tubes For Use In High Prandtl Number Systems, Connor F. Donlan

Theses and Dissertations

The development of clean energy systems is paramount to reducing mankind's climate impact. These clean energy systems include solar, wind, and nuclear power where nuclear power shows a reduced lifetime carbon dioxide footprint per kilowatt hour compared to other sources [102]. Advanced nuclear reactors, fusion energy systems, and concentrated solar power designers are looking at using molten salt heat transfer fluids and improved heat exchanger design to increase power production and efficiency of clean energy systems. The improving heat transfer within the main heat transfer components within advanced nuclear reactors will enable increased efficiencies and power production.

Heat transfer improvements …

Depressurization Characteristics Of Steam-Based Reciprocating Vacuum Pump, Hongling Deng

Dissertations

This dissertation introduces a novel vacuum technology that leverages low-pressure saturated steam and cooling-controlled condensation, offering an efficient way to utilize low-grade thermal energy sources like waste heat, steam, or solar energy. At the heart of this technology is a unique duo-chamber vacuum pump system, featuring a reciprocating piston and a heat-conductive wall, designed to generate a vacuum through steam-condensation and cooling processes.

The core of this research lies in developing and validating mechanistic models for the steam-condensation depressurization process, a complex phenomenon involving phase change and transport mechanisms. Prior to this work, these mechanisms were not sufficiently modeled or …

Gpu Based Monte Carlo Estimation Of Eddy Current Losses In Electromagnetic Coil-Core System, Adwaith Ravichandran

Theses and Dissertations

A novel parallelizable probabilistic approach to model eddy currents in AC electromagnets is presented in this research. Consequently, power loss associated with the formation of these eddy currents is estimated and validated using experimental data. Furthermore, predicting the effect of ferromagnetic alternating field enhancement on power loss in the source excitation winding has been an active area of research. Unlike a stationary field, an alternating sinusoidal field diffuses partially into the ferromagnetic material leading to a predictably sub-optimal field enhancement. To model these physics, finite element techniques employ nonlinear iterative solvers which are time consuming. A novel method is developed …

Steady And Transient Study Of Conjugate Heat Transfer In Regenerative Cooled Nozzle, Khaled Bensayah, Khadidja Kamri

Emirates Journal for Engineering Research

The Heat transfer is one of the most serious challenges that exist in a supersonic nozzle flow. The combustion chamber wall and the nozzle are exposed to high-temperature gases during combustion and gas expansion, which can eventually lead to structural failure. This paper reports a computational study of steady and transient conjugate heat transfer in regenerative water cooled nozzle. Numerical computation solved Reynolds-averaged equations based on RSM-Omega turbulence model coupling with solid-phase heat conduction equation and with coolant-phase. The effect of four inlet cooled approach length 0 inch, 6 inch, 12 inch and 18 inch are studied and validated against …

Development, Implementation, And Evaluation Of Swirl-Combustion Strategies For Optimal Performance Of Ammonia As A Fuel For Gas Turbine Engines, Varun Nanjunda Rao Viswamithra

LSU Doctoral Dissertations

In an effort to reduce harmful effects of greenhouse gas emissions, ammonia is being pursued as a fuel for power generation as it is a carbon-free energy source. However, the use of ammonia-air mixtures in premixed swirl combustors poses challenges due to low flame speed and reactivity resulting in combustor stability issues in addition to high Nitrous Oxide (NOx) emissions due to the presence of fuel-bound Nitrogen. The first part of this study attempts to overcome lean blowout limits of methane-ammonia-air mixtures using a novel, multi-point () injection strategy, whereby micron-sized holes on the swirler vanes generate a co-flowing stream …

Performance And Emissions Study Of N+3 And N+4 Engine Models With Several Fuel Types Using Npss, Abel Solomon

McKelvey School of Engineering Graduate Student Theses & Dissertations

The aviation industry is known to be one of the major contributors to greenhouse gases accounting for 4.9% of the global greenhouse emissions. With the ever-increasing threat of climate change to the overall survival of the planet, the exploration of new technologies and alternative energy sources that minimize greenhouse gas emissions are of paramount importance. In this regard, the development of propulsion systems well suited for the performance and emissions requirements of future commercial aircraft plays a crucial role. This thesis investigates N+3 and N+4 technology-level propulsion systems that are proposed by NASA as possible propulsion systems for advanced single-aisle …

The Influence Of Mixing Duct Length And Phase Of Flight On Wall Temperatures Of A Rocket Based Combined Cycle Engine In Ejector And Air-Augmented Modes, Jonathan Grow

Doctoral Dissertations and Master's Theses

Rocket Based Combined Cycle (RBCC) engines have been theorized as a possible means of powering launch vehicles and high-speed atmospheric vehicles. By incorporating aspects of both air-breathing and rocket propulsion, RBCC engines promise up to a 230 % increase in specific impulse over traditional chemical rocket propulsion by entraining a secondary flow of atmospheric air and mixing it with the exhaust of a rocket motor. Students within the Embry-Riddle Future Space Explorers and Developers Society (ERFSEDS) identified a
problem of excessive heating and structural failure of the mixing duct during launch and transonic flight of a student-built flight test vehicle. …

Cooled Liquid Rocket Thrust Chamber, Benjamin Gibson, Kealan Frederick Harris, Ryan Frank Schackel, Bjorn Thorsen

Mechanical Engineering

Cooling may affect the thrust output of a small-scale rocket. Little research is published about small-scale rocket performance. We hypothesize the thrust produced varies as the amount of cooling varies. To facilitate assessing this hypothesis, we have designed and built a liquid rocket engine rated for at approximately 25 lb_f of thrust. Our objective was to build in parallel with Cal Poly Space Systems, who built a rocket engine with similar specifications except without cooling. Our challenge is to integrate film cooling, so that the effects of cooling may be compared to Cal Poly Space System’s engine which has …

A Systematic Study Into The Design And Utilization Of Burn Wire As A Means Of Tensioning And Releasing Spacecraft Mechanisms Through Applied Joule Heating, Chandler Dye

Mechanical Engineering Undergraduate Honors Theses

The joule heating characteristics of Nichrome burn wires, often used as a thermal cutting device in mechanisms designed to fasten and release CubeSat deployables, are examined in the following thesis. Wires ranging from 0.125 inches to 2 inches long, and diameters of 30 Ga and 40 Ga, are investigated through analytical calculations and thermal simulations based on heat transfer due to joule heating, and through physical circuitry-based experiments. The temperature data is used to generate heating curves to predict the time it takes for Nichrome wires to fail under varying testing parameters. This research aims to catalog a series of …

Classification Of Electrical Current Used In Electroplastic Forming, Tyler Grimm

All Dissertations

Electrically assisted manufacturing (EAM) is the direct application of an electric current to a workpiece during manufacturing. This advanced manufacturing process has been shown to produce anomalous effects which extend beyond the current state of modeling of thermal influences. These purported non-thermal effects have collectively been termed electroplastic effects (EPEs).

While there is a distinct difference in results between steady-state (ideal DC) testing and pulsed current testing, the very definition of these two EAM methods has not been well established. A "long" pulse may be considered DC current; a "short" pulse may produce electroplastic effects; and even "steady-state" current shapes …

Detonation Confinement In A Second-Generation Radial Rotating Engine, John T. Ursino

Theses and Dissertations

In recent years, Rotating Detonation Engines (RDEs) have been coupled with turbomachinery to harness the benefits of detonative combustion. A novel type of RDE, referred to as the disk or Radial RDE (RRDE), has been developed in pursuit of length and weight savings compared to a traditional annular flow RDE. This design includes a disk-shaped device within which reactants flow from the outer radius, detonate, and exit the inner radius. In this paper several modifications have been made to a previously tested RRDE to address issues that arose with the original design. The combustion chamber diameter has been increased to …

A Computational Fluid Dynamic Analysis Of Oxyacetylene Combustion Flow For Use In Material Response Boundary Conditions, Craig Meade

Theses and Dissertations--Mechanical and Aerospace Engineering

Oxyacetylene torches are used in the aerospace industry and research to test thermal protection system materials (TPS) due to their high flame temperatures and high heat flux capabilities. The purpose of this work is to determine a combustion model to accurately simulate the high temperature flow of an oxyacetylene torch. The flow conditions around a sample material can then be used as boundary conditions when modeling TPS material response. Two separate combustion models with equilibrium chemistry were investigated using ANSYS Fluent™; the Eddy-Dissipation Model, and the Partially Premixed model.The results of this study are compared to existing experiments for validation.

Impact Of Spallation And Internal Radiation On Fibrous Ablative Materials, Raghava Sai Chaitanya Davuluri

Theses and Dissertations--Mechanical and Aerospace Engineering

Space vehicles are equipped with Thermal Protection Systems (TPS) that encounter high heat rates and protect the payload while entering a planetary atmosphere. For most missions that interest NASA, ablative materials are used as TPS. These materials undergo several mass and energy transfer mechanisms to absorb intense heat. The size and construction of the TPS are based on the composition of the planetary atmosphere and the impact of various ablative mechanisms on the flow field and the material. Therefore, it is essential to quantify the rates of different ablative phenomena to model TPS accurately. In this work, the impact of …

Investigations Of A Surrogate Fuel Based On Fischer-Tropsch Gtl And Ctl In Cvcc, Idi And Di Compression Ignition Engines, Amanda C. Weaver

College of Graduate Studies: Theses & Dissertations

With the increase in availability, feedstocks, and properties of alternative fuels, compatibility issues emerge between current engine platforms often requiring a limit on the blend percentage of alternative fuel in conventional fuel or alteration to the engine platform. Two key metrics were identified, autoignition quality and lubrication characteristics, as vital for the proper function of a compression ignition engine, and if the blend of alternative fuels matches these two criteria for the diesel standard, then the resulting blend percentage can be considered as a viable alternative for complete replacement of conventional petroleum ULSD. Autoignition quality was matched using blends S-8, …

Application Of Direct Feedback Tunable Diode Laser Absorption Spectroscopy Within A Hybrid Rocket Combustor, Connor Becnel

LSU Master's Theses

With interest in space travel and space-related science increasing in recent years, significant efforts to reduce the cost and increase the safety of rocket motors have become commonplace. Liquid rockets are currently the most commonly used system, but there is interest in the reduced complexity of hybrid rockets. For these hybrid rocket motors to become the norm, extensive research on their complex boundary layer combustion needs to be performed. Modeling these hybrid systems is of much interest to companies developing rocket motors; ultimately, small-scale experiments will help validate their behavior. This paper covers the application of a near-infrared tunable diode …

Turbine Cooling System With Energy Separation, James L. Rutledge, Matthew Fuqua, Carol M. Bryant

AFIT Patents

A method and system for cooling an engine and/or vehicle using energy separation is disclosed herein. An energy separation device is operable for separating a compressed gaseous coolant stream into a first relatively cooler coolant flow stream and a second relatively hotter coolant flow stream. The relative cooler coolant flow stream is directed to a first region requiring increased cooling and the relative hotter coolant flow stream is directed to a second region requiring lower cooling than the first region in the engine or vehicle.

Comprehensive Review Of Heat Transfer Correlations Of Supercritical Co2 In Straight Tubes Near The Critical Point: A Historical Perspective, Nicholas C. Lopes, Yang Chao, Vinusha Dasarla, Neil P. Sullivan, Mark Ricklick, Sandra Boetcher

Publications

An exhaustive review was undertaken to assemble all available correlations for supercritical CO2 in straight, round tubes of any orientation with special attention paid to how the wildly varying fluid properties near the critical point are handled. The assemblage of correlations, and subsequent discussion, is presented from a historical perspective, starting from pioneering work on the topic in the 1950s to the modern day. Despite the growing sophistication of sCO2 heat transfer correlations, modern correlations are still only generally applicable over a relatively small range of operating conditions, and there has not been a substantial increase in predictive capabilities. Recently, …

Disk Engine With Circumferential Swirl Radial Combustor, Brian Bohan, Marc Polanka, Bennett Staton

AFIT Patents

A disk engine and system configured to provide high power at a reduced axial length is disclosed herein. The disk engine includes a radial compressor, a compressor discharge manifold positioned circumferentially about compressor, a combustion chamber positioned within the discharge manifold and a radial turbine positioned radially inward of the combustion chamber.

Preliminary Study Of Shape-Memory Alloy Torsional Tubes As Thermal Management Actuators Under Non-Ideal Conditions, Paula Sanjuan Espejo, Samuel Desloover, Devon Hardy, Mark Ricklick, Frederick Calkin, David Foutch

Publications

Shape-memory alloys (SMAs) have been used in many engineering applications because of their shape-memory effect and pseudoelasticity. SMA behavior is well understood under steady and constant temperature and loading conditions, whereas transient and non-ideal conditions effects should be further investigated. In this research, SMA torque tubes are studied for use in thermal management applications as self-regulated actuators responding to a process fluid with changes in temperature, with the goal of improved system efficiency by keeping components at an optimal temperature. When utilized in a thermal management configuration, it is likely that the SMA’s thermal environment will be different than that …

Structural Sizing Of Post-Buckled Thermally Stressed Stiffened Panels, Walid Arsalane

Theses and Dissertations

Design of thermoelastic structures can be highly counterintuitive due to design-dependent loading and impact of geometric nonlinearity on the structural response. Thermal loading generates in-plane stresses in a restrained panel, but the presence of geometric nonlinearity creates an extension-bending coupling that results in considerable transverse displacement and variation in stiffness characteristics, and these affects are enhanced in post-bucking regimes. Herein a methodology for structural sizing of thermally stressed post-buckled stiffened panels is proposed and applied for optimization of the blade and hat stiffeners using a gradient-based optimizer. The stiffened panels are subjected to uniform thermal loading and optimized for minimum …

Novel Thermal Coating For High-Speed Airplanes, Abinash Satapathy, Lakshay Battu, Liam Watson, Nazanin Rajabi

Symposium of Student Scholars

In comparison to various other materials, Carbon Fiber, specifically Carbon Fiber Reinforced Polymers (CFRP), is pre-eminent amongst other materials for use on aeronautical systems. Due to its high specific strength (strength-to-weight ratio), CFRP is prominent for carrying heavy loads while maintaining a lightweight build. However, when influenced by heat resulting from air resistance, CFRP is known to undergo serious degradation that would significantly decrease the effectiveness of the polymers. To prevent this degradation and maintain the strength of the CFRP, thermal protective layers (TPLs) are designed to shield the CFRP from heat exposure. This research is focused on the examination …

Investigation Of The Low-Temperature Combustion Phenomena Of A Fischer-Tropsch Synthetic Aerospace Fuel In A Constant Volume Combustion Chamber For Greenhouse Gas Reduction, Lily H. Parker

Honors College Theses

Greenhouse gases (GHG) have a harmful effect on our environment as they trap heat in the atmosphere accelerating climate change. As such, the Federal Aviation Administration’s 2025 strategic plan to reduce GHG emissions from air transportation. This call to action for a more environmentally friendly option highlights the importance of synthetic fuels as they are more sustainable compared to traditional fossil fuels. An investigation was conducted into the thermal-physical properties of Synthetic Fischer-Tropsch (F-T) Sustainable Aviation Fuels (SAF) and the Low Temperature Combustion (LTC). LTC is composed of the Low Temperature Heat Release (LTHR) and Negative Temperature Coefficient (NTC) region, …

Jcati Carbon Fiber Recycler: Oven Enclosure, Margarita Romero

All Undergraduate Projects

Central Washington University partners with Boeing and is funded by the Joint Center of Aerospace Technology Innovation (JCATI) to develop a mechanism that takes carbon fiber wing trimmings from Boeing that are resin coated and recycles carbon fiber. This is done by crushing the wing trimmings and then putting it into a 500°C oven to melt off the resin. This project focuses on the enclosure for the oven and making sure precautions are met such as having the outside surface be less than 45c through heat transfer analysis, argon fills enclosure in 13 minutes through fluid dynamics analysis, and 99% …

A Decoupled Engineering Methodology For Accurate Prediction Of Ablative Surface Boundary Conditions In Thermal Protection Systems, Justin Cooper

Theses and Dissertations--Mechanical and Aerospace Engineering

The main objective of the present work is to demonstrate a method for prediction of aerothermal environments in the engineering design of hypersonic vehicles as an alternative to the current heritage method. Flat plate and stagnation point boundary layer theory require multiple assumptions to establish the current engineering paradigm. Chief among these assumptions is the similarity between mass and heat transfer. Origins of these assumptions are demonstrated and their relationship to conservative engineering design is analyzed, as well as conditions where they possibly break down. An alternative approach for assessing aerothermal environments from the fluid domain is presented, which permits …

Concept Evaluation And Development Of A Novel Approach For Integration Of Turbogeneration, Electrification And Supercharging On Heavy Duty Engines, Satyum Joshi

Dissertations, Master's Theses and Master's Reports

While many technologies such as electrically assisted turbocharging, exhaust energy recovery and mild hybridization have already proven to significantly increase heavy-duty engine efficiency, the key challenge to their widespread adoption has been their cost effectiveness and packaging. This research specifically addresses these challenges through evaluation and development of a novel technology concept termed as the Integrated Turbogeneration, Electrification and Supercharging (ITES) system. The concept integrates a secondary compressor, a turbocompound/expander turbine and an electric motor through a planetary gearset into the engine cranktrain. The approach enables a reduced system cost and space-claim, while maximizing the efficiency benefits of independent technologies. …

Investigations Of The Low Temperature Combustion Regions And Emissions Characteristics Of Aerospace F24 In A Constant Volume Combustion Chamber And A Common Rail Direct Injection Ci Engine, Richard C. Smith Iii

College of Graduate Studies: Theses & Dissertations

A study was conducted to investigate the low temperature combustion (LTC) regions of aerospace F24 and ULSD in the static setting of a CVCC and the dynamic setting of a CRDI research engine. This research is conducted to reduce in-cylinder emissions by understanding and implementing a technique to achieve an extended LTC. Emissions data for this study were collected during the operation of the CRDI research engine with a MKS 2030 FTIR and an AVL Microsoot 483. The parameters researched within the static setting of the CVCC included the determinations of the cool flames and NTC regions within the LTHR …