Energy Systems Commons^™

Significance Of Parameters Affecting The Performance Of A Passive Down-Draft Evaporative Cooling (Pdec) Tower With A Spray System, Daeho Kang, Richard K. Strand

Publications and Research

PDEC towers with spray systems are known to achieve substantial energy savings. Various parameters such as the wet-bulb depression, the tower height, and the wind speed have been known to be key factors affecting the performance of the system. To date, the significance of these parameters and other important factors have not been adequately treated in the literature. There also has been a lack of models that can successfully investigate potential benefits of the system under various conditions where this particular system could be applicable. To address these critical issues, this study performed a parametric analysis by using a FLUENT …

Fluid Analysis In Solar Heat Pipes, Ben Krumholz, Michael Agavo, William Dundon

Mechanical Engineering

Evacuated tube solar collectors are efficient systems that use heat pipes to facilitate heat transfer. They use incoming solar radiation to heat water. Professor Mason Medizade tasked the team with choosing a component of the system to research and test its influence on system performance. The team investigated the working fluid that runs through the heat pipes. Distilled water, acetone, and ethanol at a range of fill volumes form 1 mL to 11 mL were tested. The team's goal was to find a volume for each fluid to maximize performance of the system. Performance was defined as average temperature rise …

Disc Brake Energy Conversion, D. Coleman Badgley, Jeffrey W. Powell

Mechanical Engineering

The original goal of this project was to complete the design and building of a disc brake energy conversion project started by a former senior project team, and then spend a majority of the year performing testing in order to see if the device could be used to accurately calculate the Joule's constant. However, due to unforeseen complications and obstacles, the design and manufacturing portion of the project ended up taking much longer than anticipated. A majority of this time was spent designing the hydraulic plumbing system that would actuate the brakes. The previous team purchased some hydraulic parts and …

Me 350 Air Conditioning Experiment, Joshua Baida, Ellie Hallner, Tyler Eschenbach

Mechanical Engineering

In keeping with Cal Poly's focus on physically applying the concepts learned in the classroom, our team of engineering students has compiled a laboratory experiment displaying the basic thermodynamic cycle found in air conditioning systems. This vapor compression cycle is displayed on a visualization board that features all four major components of the system: the compressor, the evaporator, the condenser, and the throttling valve. Students will take measurements of temperature and pressure at each stage in the cycle and also gauge the power draw from the compressor to gain an understanding of how performance and electricity cost come into play …

Prosthetic Socket Cooling System, Benjamin K. Kraw, Kathy Ha, Derek Piastrelli, Cuong Lai

Mechanical Engineering

A team of four senior-level undergraduate students in the Interdisciplinary Senior Project Design course in the Engineering Department of California Polytechnic State University: San Luis Obispo have worked to develop a prosthetic socket cooling system, namely for veteran Taylor Morris and exclusively for a transfemoral prosthetic socket, under the Quality of Life+ Laboratory. This cooling system will utilize the thermoelectric effect known as the Peltier effect to transmit heat generated from the residual limb to the surrounding environment by means of forced convection over small aluminum heat sinks. Two measurement devices have also been developed to, one, measure the heat …

Multi-Stage Axial Compressor With Counter-Rotation Using Accessory Drive, Vinod Gehlot, Magdy S. Attia

Publications

A multi-stage axial compressor for counter rotation. A first series of rotor blade assemblies are mounted on and rotate with the driveshaft, each rotor blade assembly of the first series comprising a rotating stage of the multi-stage axial compressor. A second series of rotor blade assemblies provide a counter-rotating stage of the multi-stage axial compressor. An accessory drive links the second series of rotor blade assemblies to the driveshaft and causes counter-rotation of the second series of rotor blade assemblies.

How Can Occupancy Modeling And Occupancy Sensors Reduce Energy Usage In Academic Buildings: An Application Approach To University Of San Francisco, Paloma R. Duong

Master's Projects and Capstones

Buildings are amongst the highest energy consumers relative to industry and transportation. They account for 40% of the world’s energy consumption, due to the need for lighting, equipment, heating, cooling and ventilation. Academic buildings are multi-purpose buildings that create a challenge on energy reduction. Most are old and have fixed occupancy schedules, resulting in high energy consumption because these buildings experience significant occupancy variation throughout the day. Five academic buildings were analyzed; their building information, energy consumption data and methods to project energy savings have been analyzed. The case studies presented different strategies on predicting energy savings, but these have …

Energy Models Of The Txaire Houses, Tajudeen Amadu Annafi

Mechanical Engineering Theses

Model calibration is important as its functions improve building models. A calibrated model of the TxAIRE Houses #1 and #2 have been developed using the OpenStudio software. The model was developed and calibrated with data of the year 2014 but can be used predict electricity consumption of any year.

An actual meteorological year (AMY) weather file was also created for the houses which was used for calibration. The data used to develop this weather file were measured on-site which improved the accuracy of the model. It was found that an error difference of -1.0 % and -4.2 % occurred between …

Evaluating The Economic Impacts Of The Legislatively Delayed Provisions Of The 5th Edition (2014) Florida Building Code (Final Report), Florida Solar Energy Center, Robin Vieira

FSEC Energy Research Center®

This research provides an assessment of the potential economic impacts of implementing three legislatively delayed requirements of the Florida Building Code, 5th Edition (2014): 1) residential air leakage testing, 2) residential whole-house mechanical ventilation, and 3) two fire service access elevators for applicable buildings.

Least Cost Analysis For Solar Photovoltaic Maintenance Of The Wmu Miller Auditorium Array, Kelsey Pitschel

Honors Theses

The solar photovoltaic array at Miller Auditorium is a 50 kW DC system that has relied on five seasonal angle adjustments and no cleaning measures to reach an average of 64.7 MWh annual energy generation since 2012 1 . This amount of energy generation yields $7,046 in annual energy savings based on current market pricing for end use electricity of $0.1089/kWh 2 . The current adjustment schedule based on seasonal tilts accounts for an annual costs between $760 and $848, but actual adjustments have historically not taken place according to the existing schedule. The analysis focuses on optimizing net energy …

Human-Assisted Fluid Power Vehicle, Aaron Huntoon

Honors Theses

The rising cost of energy has prompted industrial and technology companies to research and implement renewable or green energy sources in every aspect of their business. This green technology can consist of sources such as: solar, wind, fluid, or others to create energy from renewable sources. The use of these various sources reduces the pollution associated with standard methods of energy development, and it will ultimately drive costs down to benefit the general population. One of the largest benefactors to the use of renewable energy sources is the transportation industry. Billions of people rely on various modes of transportation every …

Designing An Accessible Hall Effect Thruster, Matthew Baird

Honors Theses

A group of three Mechanical Engineering students have selected to design a 200 W Hall Effect Thruster to fulfill the Mechanical and Aeronautical Engineering senior design project. Preliminary studies were performed on the theory behind electric propulsion and plasma physics. The group designed the Western Hall Thruster and used COMSOL Multiphysics® simulation software to refine the magnetic circuit. The group then fabricated and performed magnetic testing of their thruster in Western Michigan University’s Aerospace Laboratory for Plasma Experiments. This testing will seek to prove that a standard research HET can be built by universities without substantial financial resources.

Automated, Autonomous And Connected Vehicle Technology Assessment, Florida Solar Energy Center, David L. Block

FSEC Energy Research Center®

The U.S. Department of Transportation (USDOT) and almost every state DOT are showing extreme interest in the application of automated and connected vehicles (ACV). This combined application can significantly reduce crashes, energy consumption, pollution and the costs of congestion which in turn will offer a fundamental change to the U.S. transportation network and system. The objective of this technology assessment project is to evaluate the vehicle technologies, actions, laws and policies that are now in place and to assess their future usage. The assessment also evaluates the highest level of automated vehicles called autonomous or self-driving vehicles. In fact, autonomous …

Development Of Distributed Off-Grid Renewable Energy System For Rural African Communities, Mateo Sebastian Guerrero, Menghong Feng

Engagement & Service-Learning Summit

Our Hybrid Energy System team is committed to develop low-cost renewable energy solutions to rural African communities where access to electricity from government grid is not available. According to a World Bank’s report, only 24% of sub-Saharan countries have access to electricity. Our team has been working with local partners to build renewable energy systems since 2008. From 2015 the team has been working on micro hydropower turbine and vertical-axis wind turbine with solar energy system combined. Our current efforts include a prototype design of a wind-solar system, using a new concept of vertical axis wind turbine to harvest wind …

A Techno-Economic Analysis Of Wind Generation In Conjunction With Compressed Air Energy In The Integrated Single Electricity Market., Brendan Cleary

Doctoral

The Integrated Single Electricity Market (I-SEM) is the proposed wholesale electricity market for Ireland and it is intended to replace the current Single Electricity Market (SEM) by 2018. Subsequently, substantial modifications will be required to the SEM and this has led to significant uncertainty for stakeholders. The SEM currently features no forecast risk for renewables such as wind and there is no concept of balance responsibility. Under the I-SEM, wind generation will be exposed to forecast risk and the requirement to be balance responsible. The use of Compressed Air Energy Storage (CAES) could represent a better system configuration which would …

Development Of A Model And Optimal Control Strategy For The Cal Poly Central Plant And Thermal Energy Storage System, Daniel Douglas Castro

Master's Theses

This thesis develops a calibrated model of the Cal Poly Central Chilled Water Plant with Thermal Energy Storage for use in determining an optimal operating control strategy. The model was developed using a transient systems simulation program (TRNSYS) that includes plant performance and manufacturer data for the primary system components, which are comprised of pumps, chillers, cooling towers, and a thermal energy storage tank. The model is calibrated to the actual measured performance of the plant using the current control strategy as a baseline. By observing and quantifying areas for potential improvement in plant performance under conditions of high campus …

Comprehensive Modeling Of Optimal Paths To Reach Nearly Zero Energy Buildings (Nzebs) For New Constructions In Europe, Florida Solar Energy Center, Delia D'Agostino

FSEC Energy Research Center®

As established by the recast of the European Union (EU) Directive on Energy Performance of Buildings (EPBD), all new buildings have to be nearly zero energy buildings (nZEBs) by the end of 2020. However, reaching this result considering cost-optimality is still an open challenge. Balancing renewable power generation with energy efficiency to reach the nZEB target is a key goal of all EU Member States. We describe results obtained from the modeling of nZEBs for new constructions in Europe using the energy performance software EnergyPlus. The model performs hourly sequential simulations showing how to best achieve nearly zero energy home …

Phased Retrofits In Existing Homes In Florida Phase I: Shallow And Deep Retrofits (February 2016), Florida Solar Energy Center, Danny Parker

FSEC Energy Research Center®

The U.S. Department of Energy's Building America research team Building America Partnership for Improved Residential Construction is collaborating with Florida Power & Light (FPL) to conduct a phased residential energy-efficiency retrofit program. This research seeks to establish impacts on annual energy and peak energy reductions from the technologies applied at two levels of retrofit--shallow and deep--with savings levels that approach the Building America program goal of reducing whole-house energy use by 40%.

Relationship Between The Home Energy Score (Hes) And The Home Energy Rating System (Hers), Florida Solar Energy Center, Philip W. Fairey

FSEC Energy Research Center®

A significant cohort of approximately 2,900 registered home energy ratings using the REM/Rate HERS software tool, as reported to RESNET, are subjected to statistical analysis by the Dillon Group, Inc. The statistical analysis determines the distribution of HES results as a function of home energy efficiency as measured by the minimum standards of the 2009 IECC and by EPA’s ENERGY STAR program.

In addition, a parametric simulation analysis is conducted by the Florida Solar Energy Center using EnergyGauge® USA version 5.0, a RESNET-accredited HERS software tool, to determine the relationship between HES scores and the HERS Index. The parametric analysis …

Nebraska Summary: S1059a Massey Ferguson 7715s, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Nebraska Summary: S1073 New Holland T7.175, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Nebraska Summary: S1098 New Holland T6.145, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Test 2171: John Deere 9520rx, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Nebraska Summary: S1075 New Holland T7.210, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Nebraska Summary: S1122 Massey Ferguson 6715s, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Nebraska Summary: S1063 Massey Ferguson 7718, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Nebraska Summary: S1102 New Holland T6.180, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Nebraska Summary: S1095 Case-Ih Maxxum 135, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Nebraska Summary: S1083 Case-Ih Puma 200, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Hybrid Metal Oxide Cycle Water Splitting, Richard B. Diver Jr, Robert D. Palumbo, Nathan P. Siegel, James E. Miller

Other Faculty Research and Publications

Hybrid thermochemical water splitting cycles are provided in which thermally reduced metal oxides particles are used to displace some but not all of the electrical requirements in a water splitting electrolytic cell. In these hybrid cycles, the thermal reduction temperature is significantly reduced compared to two-step metal-oxide thermochemical cycles in which only thermal energy is required to produce hydrogen from water. Also, unlike the conventional higher temperature cycles where the reduction step must be carried out under reduced oxygen pressure, the reduction step in the proposed hybrid cycles can be carried out in air, allowing for thermal input by a …