Energy Systems Commons^™

Florida Rural Small Business Energy Assistance Collaborative Cumulative Report Ending December 31, 2016, Florida Solar Energy Center, Janet Mcilvaine

FSEC Energy Research Center®

The U.S. Department of Agriculture's (USDA) Rural Development initiative reaches out to communities across America with many programs (http://www.rd.usda.gov/programs-services/all-programs). USDA's Rural Energy for America Program (REAP) offers grants and loan guarantees for energy efficiency improvements and renewable energy systems to agriculture operations and qualifying rural small businesses. USDA has awarded the University of Central Florida a grant to provide a limited number of subsidized Energy Audits to eligible businesses in Florida in support of USDA Rural Development (USDA-RD) Grant and Loan programs for rural small businesses. The ultimate goal of the energy audits is to increase participation in REAP. Audits …

Phased Retrofits In Existing Homes In Florida Phase Ii: Shallow Plus Retrofits [Revised], Florida Solar Energy Center, Karen Sutherland

FSEC Energy Research Center®

The U.S. Department of Energy Building America team Partnership for Improved Residential Construction is collaborating with Florida Power & Light Company (FPL) to conduct a phased residential energy-efficiency retrofit program. This research seeks to determine the impacts on annual energy reductions from the installation of advanced residential technologies. Earlier project work involving the application of two levels of retrofit, shallow and deep, found average savings of 9% and 38%, respectively. Whole-house demand reduction among the deep retrofit homes averaged 39% during FPL's peak summer hour. These savings levels approach the Building America program goals of reducing whole-house energy use of …

Energy-Efficient Management Of Mechanical Ventilation And Relative Humidity In Hot-Humid Climates, Florida Solar Energy Center, Charles Withers, Jr.

FSEC Energy Research Center®

The U.S. Department of Energy's Building America research team Building America Partnership for Improved Residential Construction conducted this research project to gain data and insight into these issues. The project focused on energy-efficient management of mechanical ventilation and RH during the cooling season. It consisted of eight test configurations. A particular focus evaluated how well a ductless seasonal energy-efficiency ratio (SEER) 21.5 mini-split heat pump (MSHP) could perform as the primary cooling system without a dehumidifier for supplemental dehumidification in a continuously mechanically ventilated house.

Photovoltaic Cooking In The Developing World, Tyler Watkins, Christopher O'Day, Omar Arriaga

Mechanical Engineering

The challenge of clean cooking is faced by hundreds of millions of people worldwide. We present a cooking technology consisting of a solar panel directly connected to an electric heater in a well-insulated chamber. Assuming continued decrease in solar panel prices, we anticipate that in a few decades Solar Electric Cooking technologies will be the most common cooking technology for the poor. Appropriate use of insulation reduces the power demand making low-power Insulated Solar Electric Cooking systems already cost competitive.

Thermal Transport In Lithium Ion Batteries: An Experimental Investigation Of Interfaces And Granular Materials, Aalok Jaisheela Uday Gaitonde

Open Access Theses

Increasing usage and recent accidents due to lithium-ion (Li-ion) batteries exploding or catching on fire has inspired research on the characterization and thermal management of these batteries. In cylindrical 18650 cells, heat generated during the battery's charge/discharge cycle is poorly dissipated to the surrounding through its metallic case due to the poor thermal conductivity of the jelly roll, which is spirally wound with many interfaces between electrodes and the polymeric separator. This work presents a technique to measure the thermal conduction across the metallic case-plastic separator interface, which ultimately limits heat transfer out of the jelly roll.

The polymeric separator …

Effect Of Ducted Hpwh On Space-Conditioning And Water Heating Energy Use - Central Florida Lab Home, Florida Solar Energy Center, Carlos Colon

FSEC Energy Research Center®

The purpose of this research is to investigate the impact of ducted heat pump water heaters (HPWHs) on space-conditioning and water heating energy use in residential applications. Two identical HPWHs, each with a capacity of 60 gal, were tested side by side at the Flexible Residential Test Facility (FRTF) laboratories on the Florida Solar Energy Center (FSEC) campus in Cocoa, Florida. The FRTF's residential buildings feature the same square footage (1,535 ft2 ), orientation, and envelope characteristics; currently, the only difference between them is the finished floor material. The east FRTF building is furnished with standard carpet flooring, whereas the …

Ev Workplace Charging Energy Use And Cost Case Study, Florida Solar Energy Center, Richard Raustad

FSEC Energy Research Center®

Efforts to increase the availability of plug-in electric vehicle (PEV) charging stations have focused on expanding public charging stations, promoting charging at the workplace and using charging stations as a shopping incentive for retail stores. This report examines the costs and energy uses to provide the charging service. Rapidly charging a PEV requires expensive electric equipment and can lead to high operating costs due to electrical demand charges. This project presents results from a detailed case study for 5 PEV chargers where the charger electricity costs are a part of a facilities electric bill. Also presented are options for minimizing …

Comparison Of The Modes And Mechanisms Of Degradation Of Experimental C-Si Pv Modules With Various Encapsulants, October 2016, Florida Solar Energy Center, Neelkanth Dhere

FSEC Energy Research Center®

Seven modules with different encapsulants, provided by the National Renewable Energy Laboratory (NREL), were installed at the Florida Solar Energy Center (FSEC) outdoor test facility for long-term durability testing in the hot and humid climate of Florida. Along with the modules, NREL also provided corresponding load resistors, junction boxes, and module connections. The modules were installed at latitude tilt, on a south facing rack on March 20, 2014.During project different types of tests such as visual inspection in environmental conditions and infrared imaging and I-V characterization were carried out on the seven module

Behaviour Of A Spd Switchable Glazing In An Outdoor Test Cell With Heat Removal Under Varying Weather Conditions, Aritra Ghosh, Brian Norton, Aidan Duffy

Articles

Suspended particle device (SPD) switchable glazing has potential to control transmission of solar radiation in the visible range by changing its transparency from 55% to 5%. Outdoor test cell characterisation of a SPD switchable glazing offered the dynamic solar heat gain coefficient (SHGC) which varied between 0.05 (when opaque) and 0.38 (when transparent). Reduction of maximum temperature rise of 11% and 15% was possible using SPD “transparent” and “opaque” state compared to same area double-glazing. Insulated test cell with water flow heat exchanger was employed to measure the cooling load reduction potential of SPD glazing while its transmission changed from …

Modeling Pyrolysis Of Large Coal Particles With Many Species, Jianqing Li

Master's Theses (2009 -)

Coal currently supplies 40% of the world’s electricity needs, and is one of the most important energy sources. As the initial stage of coal combustion, pyrolysis is a thermal decomposition process which converts coal into light gases and tars, which are subsequently consumed in combustion reactions, as well as solid char. Recently there has been interest in using slow pyrolysis as a stand-alone process for the production of chemicals and fuels from large (mm-scale) coal particles. Simulations can be used to efficiently study the impact of pyrolysis conditions on gas, tar and char yields, as well as gas and tar …

Preface-Jes Focus Issue On Electrolysis For Increased Renewable Energy Penetration, B. Pivovar, M. Carmo, K. Ayers, X. Zhang, J. O'Brien

Mechanical & Aerospace Engineering Faculty Publications

(First paragraph) Today represents a particularly exciting time, as our planet’s energy system is undergoing major changes due to dramatically decreasing renewable energy prices and increasing societal concerns over greenhouse gas emissions, criteria pollutants (arsenic, mercury, NOx, particulate matter), and climate change. These factors are pushing society toward deep decarbonization of our energy system, perhaps the most challenging issue facing the planet today. Unfortunately, wind and solar energy, while both promising generation sources, come with intermittency challenges and have limitations in their abilities to impact industrial and transportation sector demands where fossil fuel energy carriers based on chemical bonds have …

Cost Analysis Of Workplace Charging For Electric Vehicles, Florida Solar Energy Center, Richard Raustad

FSEC Energy Research Center®

This report examines the life-cycle costs associated with the operation of electric vehicle supply equipment (EVSE) and the impact that plug-in electric vehicle (PEV) charging may have on commercial building electricity cost. This study assumed that a utility electric meter was attached to each charging station and that 10 kWh of energy was required to replenish the energy consumed during a typical 35-mile daily work commute. Through a life-cycle assessment of typical EVSE equipment, including first cost and maintenance and operating costs, it was found that AC Level 1 or 2 workplace charging can be similar to or lower in …

Lennar Ventures Power Purchase Agreement Analysis, Florida Solar Energy Center, Philip W. Fairey

FSEC Energy Research Center®

An analysis was performed to determine the cost-effectiveness of photovoltaic (PV) system Power Purchase Agreements for prototype homes in 13 United States climate locations. EnergyGauge® USA v.5.1 software was used to simulate the energy use of one-story, three-bedroom, 2000 ft² , single-family, frame prototype homes in thirteen representative U.S. climates comprising six IECC climate zones. The same software was used to simulate the power production of PV systems designed to provide approximately 75% of the annual electric energy required by the prototype homes. The net present value (NPV) of the photovoltaic PPA was then calculated as the difference in …

Evaluation Of The Impact Of Slab Foundation Heat Transfer On Heating And Cooling In Florida, Florida Solar Energy Center, Danny Parker

FSEC Energy Research Center®

The U.S. Department of Energy's Building America Partnership for Improved Residential Construction (BA-PIRC) performed experiments in the Florida Solar Energy Center's Flexible Residential Test Facility intended to assess for the first time (1) how slab-on-grade construction influences interior cooling in a cooling-dominated climate and (2) how the difference in a carpeted versus uncarpeted building might influence heating and cooling energy use.

Final Report: Cooling Seasonal Energy And Peak Demand Impacts Of Improved Duct Insulation On Fixed-Capacity (Seer 13) And Variable-Capacity (Seer 22) Heat Pumps, Florida Solar Energy Center, Charles Withers, Jr.

FSEC Energy Research Center®

Previous phase 1, 2, and 3 research identified that duct conductive losses to an attic environment imposed greater relative energy losses for the variable-capacity systems compared to the fixed-capacity systems (Cummings and Withers 2011) because of the longer dwell time of conditioned air in the ducts. The purpose of the Phase 4 experiments reported here was to see if duct R-value enhancement would benefit the overall operating efficiency of the variable-capacity system relatively more than the fixed-capacity system. The current Phase 4 experiments (the primary focus of this report) found that this was a secondary effect.

Flexible Residential Test Facility: Impact Of Infiltration And Ventilation On Measured Cooling Season Energy And Moisture Levels (2016), Florida Solar Energy Center, Danny Parker

FSEC Energy Research Center®

Originally published in January 2014, this revision of the report clarifies and corrects references to Standard 62.2 as the 2013 version (62.2-2013), and it corrects the total CFM requirement for the subject buildings under the standard. Further, two plots have been updated to distinguish between the mechanical CFM and the total CFM required for the subject buildings under Standard 62.2-2013.

The Feasibility Of Utilising Compressed Natural Gas As Part Of A Systematic Approach To Establishing The Necessary Groundwork For The Hydrogen Based Transport Economy, James Brunton, John Howlett, David Kennedy

Conference Papers

One key objective for vehicle manufacturers is to develop technology and infrastructure to facilitate the progression from combustion to conversion by the year 2050. In the short to medium term however, the combustion of fossil fuels such as petrol and diesel, coupled with advanced transmission innovations and emission control technology that are governed by strict Euro VI regulations appears to be the main path forward for the transport sector and the environment. This paper presents the feasibility of utilising the developing compressed natural gas network capabilities as part of a systematic approach to establishing the necessary groundwork for a hydrogen …

Dynamic Modeling And Validation Of Micro-Chp Systems, Apurva Badithela, Neera Jain, Austin Nash

The Summer Undergraduate Research Fellowship (SURF) Symposium

Micro-Combined Heat and Power (micro-CHP) units locally generate electricity to simultaneously provide power and heat for residential buildings. Apart from the potential benefits of reducing carbon emissions and increasing robustness to brownouts and blackouts, micro-CHP systems can be controlled to meet energy demands. Micro-CHP systems consist of a prime mover that generates electricity, such as a fuel cell, an internal combustion engine, or a Stirling engine, and a waste heat recovery system that enables utilization of heat generated as a byproduct of electricity generation. Often, a thermal energy storage system is integrated with micro-CHP systems, thereby decoupling, in time, the …

Dynamic Modeling Of Contact-Mode Triboelectric Generators By Lagrange’S Equations, Sean M. Gauntt, James Gibert

The Summer Undergraduate Research Fellowship (SURF) Symposium

Electret based energy scavenging devices utilize electrostatic induction to convert mechanical energy into electrical energy. Uses for these devices include harvesting ambient energy in the environment and acting as sensors for a range of applications. These types of devices have been used in MEMS applications for over a decade. However, recently there is an interest in Triboelectric generators/harvesters, i.e., electret based harvesters that relies on triboelectrification as well as electrostatic induction. The literature is filled with a variety of designs for the latter devices, constructed from materials ranging from paper and thin films; rendering the generators lightweight, flexible and inexpensive. …

A Fast Model For The Simulation Of External Gear Pumps, Zechao Lu, Xinran Zhao, Andrea Vacca

The Summer Undergraduate Research Fellowship (SURF) Symposium

External gear pump is an important category of positive displacement fluid machines used to perform the mechanical–hydraulic energy conversions in many fluid power applications. An efficient numerical simulation program is needed to simulate the system in order to provide a direction for design purpose. The model consists of a lumped parameter fluid dynamic model and a model that simulates the radial micro-motions of the gear’s axes of rotation. The system consists of a set of ordinary differential equations related to the conservation on mass of the internal control volumes of the pump, which are given by the tooth space volumes …

Dynamic Behavior Of A Clamped-Clamped Bi-Stable Laminate For Energy Harvesting, Ajay V. Kumar, Andres F. Arrieta Ph.D., Myungwon Hwang

The Summer Undergraduate Research Fellowship (SURF) Symposium

Multi-stable laminates have many applications in morphing structures, energy harvesting devices, and metamaterials due to the specific characteristics attributed to the exhibited stable states. Changes between stable states allow for large deflections, on-demand variation of the stiffness of compliant structures embedded within these elements, and control of effective dynamic properties in periodic lattices. These changes in state can be accessed via a snap-through instability triggered by introducing a well-defined activation energy. The resulting oscillations could enable broadband energy harvesting via piezoelectric transduction and resistive circuits. In this paper, a clamped-clamped bi-stable laminate is studied to understand the behavior of the …

A System Of Solar Devices In Public Places For Helping Meet Energy Demand, John Salmon

BYU Research Development Office Research Networking Conference

The BYU Engineering and System Design Lab has an alternative energy research group exploring how to embed solar devices throughout our community and campus

Parametric And Design Analysis On Thermoelectric Generators, Shouyuan Huang

Open Access Theses

In facing the limited energy source reserves and environmental problems, thermoelectric generators (TEGs) are one of the promising waste heat recovery systems. The modern TEGs for exhaust stream (e.g. from automobiles) can improve the fuel economy by around 5%, taking advantage of the recent developed thermoelectric (TE) materials.

In this work, we aimed at designing a TEG as an add-on module for a gas-phase heat exchanger with maximized power output, and without negative impact (e.g. maintaining a minimum heat dissipation rate from the hot side). We first developed a parametric optimization algorithm using response surface method (RSM) and genetic algorithm …

Thermoelectric Material Property Measurement For Flexible Films, Courtney Hollar

Boise State University Theses and Dissertations

The market for wearable electronics and implantable medical devices continues to grow. Within the next several years, the wearable electronic and implantable medical devices market will reach $31.2 billion and $73.9 billion, respectively. Currently, the most commonly used power source is the rigid lithium ion battery. In order to further optimize the devices, flexible autonomous power sources, such as thermoelectric generators, can replace traditional battery systems.

Flexible thermoelectric films were created using a wet deposition approach and synthesized into ink suitable for either spin coating or screen printing. This study focuses on Seebeck coefficient, electrical conductivity, and thermal conductivity measurements. …

Florida Rural Small Business Energy Assistance Collaborative Cumulative Report Ending July 31, 2016, Florida Solar Energy Center, Janet Mcilvaine

FSEC Energy Research Center®

The U.S. Department of Agriculture's (USDA) Rural Development initiative reaches out to communities across America with many programs (http://www.rd.usda.gov/programs-services/all-programs). USDA's Rural Energy for America Program (REAP) offers grants and loan guarantees for energy efficiency improvements and renewable energy systems to agriculture operations and qualifying rural small businesses. USDA has awarded the University of Central Florida a grant to provide a limited number of subsidized Energy Audits to eligible businesses in Florida in support of USDA Rural Development (USDA-RD) Grant and Loan programs for rural small businesses. The ultimate goal of the energy audits is to increase participation in …

Cost Effectiveness Of Energy Efficiency And On-Site Photovoltaic Power For 2015 Iecc Energy Rating Index (Eri) Compliance (Draft), Florida Solar Energy Center, Philip W. Fairey

FSEC Energy Research Center®

EnergyGauge® USA v.5.1 is used to simulate the energy use of one-story, three-bedroom, 2000 ft² , single-family, frame homes in sixteen representative U.S. climates comprising all eight IECC climate zones. The energy use of the Section R406.2 minimum efficiency home (the Baseline Home) is compared against the energy use of homes complying with the prescriptive requirements of Section R402 of the 2015 IECC and against homes complying with the Section R406 Energy Rating Index (ERI) Compliance Alternative. The improvement cost and energy savings of the improved homes relative to the Baseline Home are then used to determine the cost …

Wake Character In The Wind Turbine Array: (Dis-)Organization, Spatial And Dynamic Evolution And Low-Dimensional Modeling, Nicholas Michael Hamilton

Dissertations and Theses

To maximize the effectiveness of the rapidly increasing capacity of installed wind energy resources, new models must be developed that are capable of more nuanced control of each wind turbine so that each device is more responsive to inflow events. Models used to plan wind turbine arrays and control behavior of devices within the farm currently make questionable estimates of the incoming atmospheric flow and update turbine configurations infrequently. As a result, wind turbines often operate at diminished capacities, especially in arrays where wind turbine wakes interact and inflow conditions are far from ideal. New turbine control and wake prediction …

Go With The Flow –Thermoelectric Energy, Shawn Bell

Middle School Lesson Plans

In this unit, students will learn how thermal energy be transferred and transformed. They will carry out investigations to gather evidence to support an explanation about direct conversion of heat into electrical energy. They will develop a model that shows the components of the system and changes in the system being investigated, and they will use evidence from the investigation to construct an explanation for how the energy flows.

Advanced Technologies For Sustainable Systems, Hesham Safwat

Mechanical Engineering

No abstract provided.

2015 Electric Vehicle Market Summary And Barriers, Florida Solar Energy Center, David L. Block

FSEC Energy Research Center®

The object of this research report is to present the current market status of plug-in-electric vehicles (PEVs) and to predict their future penetration within the world and U.S. markets. The sales values for 2015 show that China leads in yearly sales at 214,283 (triple increase for 2014) followed by Western Europe at 184,500 vehicles sold. The U.S. is third at 115,262 followed by Japan at 46,339 vehicles. These four countries comprise 95% of the global sales market. The world total of EV sales for 2015 is estimated to be 565,668 up from 315,519 in 2014. This data also shows that …