Energy Systems Commons^™

Fermentability Of Concentrated Sulfuric Acid Hydrolyzates From Aspenwood And Pinewood, Kando Janga

Tanzania Journal of Engineering and Technology (TJET)

The fermentability of hydrolyzates derived from two-stage concentrated sulfuric acid hydrolysis of Trembling aspen (Populus tremula) and Scots pine (Pinus sylvestris) were investigated. Three types of hydrolyzates were produced at mild, moderate and high decrystallization severity conditions. Portions of each of the original hydrolyzates were concentrated by vacuum evaporation to increase the sugar fraction to simulate industrial applications. Both sets of hydrolyzates were fermented anaerobically using Saccharomyces cerevisiae ATCC 96581. After 23 hours of fermentation, complete glucose consumption was observed for all the original hydrolyzates, with no signs of inhibition. The ethanol yields from these hydrolyzates ranged from 68% to …

Analysis Of Performance Characteristics Predicted From Several Experimental Data And Conversion Methods For Pumps As Turbine Application Using Statistical Techniques, Ombeni J. Mdee

Tanzania Journal of Engineering and Technology (TJET)

Different performance characteristics have been indicated when running centrifugal pumps in the reverse direction. The water flows from the discharge side of the pump to the suction side to run in the reverse direction and generate the mechanical rotational energy for the micro-hydropower plant. The current study evaluates the extent of variation of performance characteristics predicted by several experimental data from different pump-specific speeds and conversion methods. The performance characteristics discussed include the head, flow rate, efficiency and specific speed. The flow rate and head of a pump operating in pump mode divided with the characteristic of the pump operating …

Solar Photovoltaic Performance Monitoring: A Bibliometric Review, Research Gaps And Opportunities, Javed Sayyad, Paresh Nasikkar

Library Philosophy and Practice (e-journal)

Electrical power generation has been revolutionized by growing demand and use of Renewable Energy (RE) sources such as Solar Photovoltaic (SPV) as the main electricity source in modern times. The main objective of this bibliometric analysis is to understand the scope of the literature available for SPV performance characterization. This detailed reviewed was performed on the documents related to SPV research considering all the subject categories from Scopus and Web of Science (WoS) databases. The patterns for the particular set of keywords were broke down with the recuperated outcomes from Scopus database in the language, publication type, year of publication, …

Field Testing The Effects Of Low Reynolds Number On The Power Performance Of The Cal Poly Wind Power Research Center Small Wind Turbine, John B. Cunningham

Master's Theses

This thesis report investigates the effects of low Reynolds number on the power performance of a 3.74 m diameter horizontal axis wind turbine. The small wind turbine was field tested at the Cal Poly Wind Power Research Center to acquire its coefficient of performance, C­_p, vs. tip speed ratio, λ, characteristics. A description of both the wind turbine and test setup are provided. Data filtration and processing techniques were developed to ensure a valid method to analyze and characterize wind power measurements taken in a highly variable environment. The test results demonstrated a significant drop in the …

Experimental Investigation Of The Wind Energy Harvesting Potential Of A Stand-Alone Piezoelectric Strip, Phillip Christopher Scott

Mechanical Engineering ETDs

The purpose of the study was to investigate the feasibility of harvesting wind energy on a small scale in residential areas. The method investigated was the initiation of movement-induced excitation (MIE), a type of aeroelastic flutter, within samples of polyvinylidine fluoride (PVDF), a piezoelectric polymer. Single samples of PVDF were secured in a wind tunnel and sample voltage was measured over a broad range of wind speeds. Power was calculated then via the addition of ohmic resistance matched to the magnitude of the capacitive impedances of the samples. The geometry of the PVDF samples studied was maintained as a simple …

What Difference Does A Catalyst Make?, Tammy Guthrie, Mike Jackson, Holly Haney

High School Lesson Plans

Students will use different catalysts for the decomposition of Hydrogen Peroxide, to determine if different catalysts affect the energy that is generated during the reaction.

Performance Analysis Of Renewable Energy Resources In Rural Areas: A Case Study Of Solar Energy, Jackson Justo

Tanzania Journal of Engineering and Technology (TJET)

This paper presents an overview of the recent development trends of solar photovoltaic (PV) systems and the performance in the Tanzanian context. The two types of solar power generation that are considered in this paper are: i) solar PV systems and ii) concentrated solar power (CSP). The two are compared in terms of cost of energy and energy storage mechanism. Moreover, the effect of ambient temperature on the solar PV module is analyzed. In addition, a detailed analysis on using solar axis tracking to increase the power generation is also presented. The extent to which the cell surface temperature and …

Modeling And Control Of Solar Pv With Battery Energy Storage For Rural Electrification, Irene Masenge

Tanzania Journal of Engineering and Technology (TJET)

In rural areas where electric power grid network is rarely available, power generation from renewable energy resource such as solar photovoltaic (PV) is mostly accomplished in standalone mode. The standalone solar PV system requires energy storage device to achieve reliable power supply to the end users. This paper presents modelling and coordination control of solar PV with battery energy storage system (BESS) for rural-electrification applications. The proposed control is accomplished via a bidirectional buck-boost converter with the objective of maintaining voltage at the DC bus constant. Simulation results based-on MATLAB/Simulink platform confirms good performance of the proposed system

Performance Analysis For Single-Stage And Multi-Stage Coreless Axial Flux Permanent Magnet Generator With Different Rotor Structures, Habib Asiful

Student Works (2020-2029)

Axial flux permanent magnet (AFPM) generator is a good candidate for both low and high-speed applications. Compared to radial flux machines, AFPM generators can be easily cascaded for enhanced power/torque while maintaining a fixed machine diameter. To improve power density and reduce cogging torque, some researchers have proposed the removal of iron core in the stator of AFPM machine, giving rise to the concept of coreless AFPM machine. Nevertheless, most of these coreless machines still require back iron on the rotor and/stator to reduce leakage flux. In this project, different rotor structures for single-stage coreless AFPM generators were considered, using …

An Integrated Resource Plan For Arizona Public Service Electric (Aps), Irene Boghdadi, Randy Chiu

Master's Projects and Capstones

Our Masters Capstone Project is an Integrated Resource Plan (IRP) for Arizona’s largest electric utility, Arizona Public Service Electric (APS).

An IRP is developed by utilities to identify the optimal combination of demand- and supply-side resources needed to reliably meet forecasted demand for energy and capacity, including a planning reserve margin, over a future period.

In addition to APS’s obligation to serve the growing load in Arizona while minimizing costs, it is required by the state to adhere to the Renewable Energy Standard (RES) policy of 15 percent retail sales from renewable energy resources by 2025.

The analysis described in …

Dartmouth Formula Racing: Full Electric Battery System Design, Matt Gardner, Jacob Hagler, Ruthie Nordhoff, Otto Salmi

ENGS 89/90 Reports

Dartmouth Formula Racing (DFR) lacked an electrical energy storage system that was Formula Hybrid rules-compliant, optimized for FH events, safe, reliable, and integrated with the rest of their vehicle. Additionally, the team lacked the academic and professional resources required to bring a thorough, analytical approach to the design, testing, and documentation of the new storage system. Our team designed and built a Lithium-Ion battery pack (accumulator) containing energy storage, active cooling, battery management and temperature monitoring systems, and control circuitry compatible with DFR’s vehicle. Collaboration throughout design, fabrication, assembly and testing processes ensured effective knowledge transfer to the DFR team.

Residential Thermal Storage And Cooling, Joao Marcelo Rocha Belmonte, Jacob Anderson, Andrew Clarke, Daphne Forester, Bianca Hardtke, Josh Hartman, Marc D. Compere

Sustainability Conference

No abstract provided.

Dual-Axis Solar Tracker, Bryan Kennedy

All Undergraduate Projects

Renewable energies, and fuels that are not fossil fuel-based, are one of the prolific topics of debate in modern society. With climate change now becoming a primary focus for scientists and innovators of today, one of the areas for the largest amount of potential and growth is that of the capturing and utilization of Solar Energy. This method involves using a mechanical system to track the progression of the sun as it traverses the sky throughout the day. A dual-axis solar tracker such as the one designed and built for this project, can follow the sun both azimuthally and in …

An Examination To Pathways Powering Car Using Clean Energy, Marina Miranda

Graduate Theses, Dissertations, and Problem Reports (ETD)

Traditional vehicles powered by internal combustion engines contribute significantly to increasing emissions of greenhouses gasses (GHG). There has been increasing interest in powering vehicles using green energy include using electricity produced by wind turbine and solar panel. The green electricity can be used to directly charge the Battery Electric Vehicles (BEV), or producing hydrogen as fuel for Fuel Cell Electric Vehicles (FCEV) by converting electrical energy to hydrogen (H₂) through water electrolysis. The low energy density H₂ produced can be stored on board as either compressed H₂ or liquefied H₂.

This research examines the …

Carbon-Based Interlayers In Perovskite Solar Cells, Aleksandr P. Litvin, Xiaoyu Zhang, Kevin Berwick, Anatoly V. Fedorov, Weitao Zheng, Alexander V. Baranov

Articles

Perovskites are solution-processed, high-performance semiconductors of interest in low-cost photovoltaics. The interfaces between the perovskite photoactive layers and the top and bottom contacts are crucial for efficient charge transport and minimizing trapping. Control of the collection of charge carriers at these interfaces is decisive to device performance. Here, we review recent progress in the realization of efficient perovskite solar cells using cheap, easily processed, stable, carbon-based interlayers. Interface materials including graphene, carbon nanotubes, fullerenes, graphene quantum dots and carbon dots are introduced and their influence on device performance is discussed.

The Potentials Of Faecal Sludge Treatment Using Local Conditioners In Tanzania: A Review, Doglas Benjamin1

Tanzania Journal of Engineering and Technology (TJET)

Worldwide, every day human beings generate millions of tons of Faecal Sludge (FS), which is rich in water, nutrients, energy, and organic compounds. Yet FS is not being managed in a way that permits us to derive value from its reuse, while at the same time, millions of farmers struggle with depleted soils and lack of water. In most of the developing countries, energy for cooking is mainly derived from cutting of trees, either as wood or charcoal. Resource recovery and reuse from FS can create livelihoods, enhance food security, support green economies, reduce waste and contribute to cost recovery …

Designing An Accessible Wave Energy Conversion Device For Powering Ocean Sensors, Sophie Coppieters ‘T Wallant

Independent Study Project (ISP) Collection

Currently, less than 5% of our oceans are comprehensively monitored and much more ocean data is needed to facilitate understanding of ocean physics, carbon cycling, and ocean ecosystems. Today, most autonomous ocean sensors are powered by primary battery, which have both limited capacity and lifetime. The goal of this research is to design a small, accessible renewable wave energy device to power autonomous free-floating ocean sensors. By designing a cheap, accessible, and simple wave energy converter, this work hopes to make ocean sensor deployment easier and cheaper for researchers, increase the lifetime of autonomous ocean sensors, and reduce the reliance …

Understanding Of The Ship Design Energy Efficiency And Its Implications In Practice, Haichao Yuan

Maritime Safety & Environment Management Dissertations (Dalian)

No abstract provided.

Design, Development And Implementation Of An Electrical Controller For A Solar-Electrical Collector, Sahar Mahboob, Razieh Pourdarbani, Bahman Behfar, Hossein Behfar

Emirates Journal for Engineering Research

Todays, maintaining atmospheric health is one of the most important prerequisites for sustainable global economic development, and the international community has no choice but to switch to renewable energies, including solar energy. The goal of the study was to provide a temperature of 60 ° C for drying summer fruits such as apricots therefore we investigated the effect of temperature control systems on the solar-electrical collector performance. Three LM35 temperature sensors were placed at 3 points of the collector (before the air inlet to the collector, after the air outlet from the collector and after heating elements) that were linked …

Swarm Behavior To Mitigate Rebound In Air Conditioning Demand Response Events, Jason Yasuto Kuwada

Boise State University Theses and Dissertations

Thermostatically Controlled Loads (TCLs) have shown great potential for Demand Response (DR) events. However, it has been commonly seen that DR events using TCLs may cause demand rebound, especially in homogeneous populations. To further explore the potential for DR events, as well as the negative effects, a stability and resilience analysis were performed on multiple populations and verified with agent based modeling simulations.

At the core of this study is an added thermostat criterion created from the combination of a proportional gain and the average compressor operating state of neighboring TCLs. Where DR events in TCLs are commonly controlled by …

Energy Transformation And Conservation Investigation, Mike Jackson, Holly Haney

High School Lesson Plans

Students will use a thermoelectric generator module to analyze the relationship between thermal and electrical energies. Using data collection sensors and analysis software, students will investigate the relationship between the temperature gradient across a thermoelectric generator module and the resulting electrical potential. Students will then use their data and analysis to solve problems relating to waste thermal energy in electrical systems and communicate their work to their peers and teacher.

The Comparative Analysis Of The Performances Of Four And Six Pole Pairs Permanent Magnet Synchronous Generator, Ra Msuya

Tanzania Journal of Engineering and Technology (TJET)

Wind power applications using multi-poles permanent magnet generators have become very attractive especially in small ratings. Low-speed multi-pole PM generators are maintenance-free and may be used in different climate conditions. Most of the low speed wind turbine generators presented is permanent magnet machines, which have advantages of high efficiency and reliability since there is no need of external excitation and conductor losses are removed from the rotor. From the study two types of PM AC generator are designed with 6 pole pairs and the other one with 4 pole pairs. These generators were designed and analysed using Maxwell software. The …

Heat: Hydraulic And Electric Animation Team, Tyler J. Couvrette, Michael J. Cain, Sara T. Novell, Dexter K. Yanagisawa

Mechanical Engineering

Each New Years’ Day, the Cal Poly Rose Float presents a flower-covered float to the world at the Tournament of Roses parade. This floral display, paired with moving mechanical animations, shows off Cal Poly to the world. This project strove to keep Cal Poly on the cutting edge of technology both in parade floats, and in engineering, by creating a completely electric-powered animation system.

To accomplish this, a group of students set out to make the fully electric animation system that can power both the hydraulic and electric mechanisms on the Float. This was accomplished through months of planning and …

Exploring The Electrical Properties Of Twisted Bilayer Graphene, William Shannon

Senior Theses

Two-dimensional materials exhibit properties unlike anything else seen in conventional substances. Electrons in these materials are confined to move only in the plane. In order to explore the effects of these materials, we have built apparatus and refined procedures with which to create two-dimensional structures. Two-dimensional devices have been made using exfoliated graphene and placed on gold contacts. Their topography has been observed using Atomic Force Microscopy (AFM) confirming samples with monolayer, bilayer, and twisted bilayer structure. Relative work functions of each have been measured using Kelvin Probe Force Microscopy (KPFM) showing that twisted bilayer graphene has a surface potential …

Surface And Interface Properties In Thin-Film Solar Cells: Using Soft X-Rays And Electrons To Unravel The Electronic And Chemical Structure, Lothar Weinhardt, Dirk Hauschild, Clemens Heske

Chemistry and Biochemistry Faculty Research

Thin‐film solar cells have great potential to overtake the currently dominant silicon‐based solar cell technologies in a strongly growing market. Such thin‐film devices consist of a multilayer structure, for which charge‐carrier transport across interfaces plays a crucial role in minimizing the associated recombination losses and achieving high solar conversion efficiencies. Further development can strongly profit from a high‐level characterization that gives a local, electronic, and chemical picture of the interface properties, which allows for an insight‐driven optimization. Herein, the authors' recent progress of applying a “toolbox” of high‐level laboratory‐ and synchrotron‐based electron and soft X‐ray spectroscopies to characterize the chemical …

Energy Efficiency Evaluation Of Blower Heater Non-Purge Compressed Air Dryers, Alexandra M. Botts

Graduate Theses, Dissertations, and Problem Reports (ETD)

There are several compressed air dryers available for industrial use including, refrigerant, desiccant, and membrane. This research focuses on twin tower regenerative closed loop desiccant dryers, specifically: blower heater non-purge (BHNP) with and without cooling water pumps, Compressed-air Heater Purge (CHP), Blower Heater Purge (BHP), and Pressure Swing Heaterless (PSH). These styles of dryers are used mainly in industries that require extremely dry air such as, food manufacturing, medical air, or sensitive technology manufacturers. The research was conducted by collecting and analyzing real time current draw data on air compressors and associated dryers at eight different facilities (13 compressor systems) …

Networked Microgrid Optimization And Energy Management, Robert S. Jane

Dissertations, Master's Theses and Master's Reports

Military vehicles possess attributes consistent with a microgrid, containing electrical energy generation, storage, government furnished equipment (GFE), and the ability to share these capabilities via interconnection. Many military vehicles have significant energy storage capacity to satisfy silent watch requirements, making them particularly well-suited to share their energy storage capabilities with stationary microgrids for more efficient energy management. Further, the energy generation capacity and the fuel consumption rate of the vehicles are comparable to standard diesel generators, for certain scenarios, the use of the vehicles could result in more efficient operation. Energy management of a microgrid is an open area of …

Intelligent Application Of Flexible Ac Transmission System Components In An Evolving Power Grid, Robert Wall

Graduate Theses and Dissertations

The world revolves around energy and the energy sector is continually transforming and evolving. The status quo has been set by governing agencies in the United States for completely reliable power. The demand for energy efficiency continually rises for multiple reasons. Technology has improved for all sectors of the power grid, including renewable energy sources, fault protection, and SMART grid technology. The addition of new energy sources has led to the decommissioning of inefficient energy sources. The implementation of new technologies and power load on a large scale, coupled with the removal of grid stabilizers has posed different challenges that …

Electrochemical Hydrogenation Of Acetone To Produce Isopropanol Using A Polymer Electrolyte Membrane Reactor, Chen Li, Ashanti M. Sallee, Xiaoyu Zhang, Sandeep Kumar

Civil & Environmental Engineering Faculty Publications

Electrochemical hydrogenation (ECH) of acetone is a relatively new method to produce isopropanol. It provides an alternative way of upgrading bio-fuels with less energy consumption and chemical waste as compared to conventional methods. In this paper, Polymer Electrolyte Membrane Fuel Cell (PEMFC) hardware was used as an electrochemical reactor to hydrogenate acetone to produce isopropanol and diisopropyl ether as a byproduct. High current efficiency (59.7%) and selectivity (>90%) were achieved, while ECH was carried out in mild conditions (65 degrees C and atmospheric pressure). Various operating parameters were evaluated to determine their effects on the yield of acetone and …

What Can I Do As A Student To Make A Positive Impact On The Environment?, Tammy Guthrie, Greg Herzig, Kathy Prophet, Cassie Kautzer

Middle School Lesson Plans

Students discover ways they can make a positive impact on the environment.