Energy Systems Commons^™

Synthetic Inertia Provision For Load Frequency Control In Networks With High Penetration Of Renewable Energy Sources, Paulina Mkoi

Tanzania Journal of Engineering and Technology (TJET)

The integration of renewable energy sources (RESs) such as solar photovoltaic (PV) and wind energy has become a promising solution as the world shifts toward clean energy. Solar PV and wind resources are increasingly replacing conventional synchronous generators, leading to reduced system inertia and increased vulnerability to frequency instability during disturbances. To address this challenge, this study proposes a novel synthetic inertia provision strategy using a battery energy storage system (BESS) integrated alongside solar PV. The proposed method dynamically compensates for the loss of inertia by considering the variability of solar PV output due to changes in irradiance and temperature. …

Long-Range Inertia Prediction Considering Contemporary Evolution Of Power Grid Networks, Peter M. Makolo

Tanzania Journal of Engineering and Technology (TJET)

Reduced network inertia due to high penetration levels of non-synchronous generators in modern power systems is becoming a pressing issue. As a result, very quick inertial responses are observed after contingency events in networks. Due to quick inertial responses, there is a practically very limited time interval for control actions in real-time. Thus, system operators need to understand the prior inertia values to plan, control, and operate the network securely. Long-range forecasting of the network's inertia values, in contrast to short-range forecasting techniques, can pinpoint when the network is most likely to be vulnerable in a reasonable time ahead. Thus, …

Heavy Metals Pollution In Roadside Ecosystems, Lilian Matafu

Tanzania Journal of Engineering and Technology (TJET)

Heavy metals refer to metallic elements that are characterized by having a relatively high density and they are toxic or poisonous even at low concentration. They are environmental pollutant owing to toxicity and longevity in atmosphere and ability to accumulate in living things via bioaccumulation. They tend to enter in different system such as food chain. Analyses of water, soil sediment and the surrounding growing plants (Cynodon dactylon and Cyperus species) for selected heavy metals (Cd, Pb, Zn and Cu) were conducted on a roadside pond located at Boko MSB, Dar es Salaam. Pond water, soil sediments and plant samples …

A Bibliometric Analysis Of Pat-Seig Evolution As An Alternative Energy Generation Method, Emanuel J. Nyirenda

Tanzania Journal of Engineering and Technology (TJET)

Pumps as Turbines (PATs) coupled with Self-Excited Induction Generators (SEIGs) as an alternative energy generation method have been the subject of significant research in recent years. This paper presents a bibliometric analysis of the evolution of PAT-SEIG technology as an alternative energy generation source. An analysis of a comprehensive dataset of peer-reviewed journal articles, conference proceedings, and patents related to PAT-SEIG systems, using advanced bibliometric techniques and PRISMA to identify key research themes, influential authors, the growth of the field and patterns of collaboration, and changes in research focus over time. Over a publication period of 32 years, a total …

Assessment Of Wind Speed Characteristics And Available Wind Power Potential For Electricity Generation In Tanzania, Mwingereza John Kumwenda

Tanzania Journal of Engineering and Technology (TJET)

The energy demand and its associated crises are attracting significant attention due to population increase and economic growth especially in developing countries. Fossil fuel-based energy source stand as a prominent anthropogenic resource but they are accompanied with increased carbon emissions and heightened environmental concerns. Renewable energy sources such as wind energy can offers a lot of potential for sustainable growth in the energy sector of developing nations like Tanzania. Thus, this work investigated wind speed characteristics and available wind power potential in six selected regions in Tanzania with different topographical features for future electricity generation. The data of the wind …

Efficient Operation Of Direct Coupled Solar Home Pv System: A Case Of Solar Home Pv System Installed In Dodoma, Tanzania, Sarah P. Ayeng'o

Tanzania Journal of Engineering and Technology (TJET)

Direct coupled Photovoltaic (PV) system is a common topology among most of the off-grid communities in the world. This topology has less components hence resulting in low investment costs. However, it suffers much losses when battery operating voltage is far from maximum power point voltage of PV modules. This scenario can be attributed by different factors such as; variation in solar radiation, load profile and temperature. Efficient operation of these systems is required in order to reduce losses. Usually in direct coupled system, PV modules are connected in parallel with batteries through a charge controller hence making PV output to …

Multiphysics Modeling Of Solid Oxide Fuel Cells For Gradient Minimization And Inductive Loop Analysis In Impedance Spectroscopy Using Machine Learning-Based Microstructural Property Estimation, Muhammad Usman Khan

College of Graduate Studies: Theses & Dissertations

Solid oxide fuel cells have significant advantages in renewable energy utilization due to their high efficiency, fuel flexibility, and low emissions. However, despite the numerous efforts of technology, thermal and current density gradients and impedance behavior fluctuations are still causing performance degradation. A combined computational framework that integrates machine learning and three-dimensional Multiphysics modeling is needed to investigate and optimize the performance of solid oxide fuel cells. A machine learning model, trained on synthetic microstructure data by percolation analysis, is used to predict important microstructural parameters like triple phase boundary density and geometric tortuosity. These are then employed in a …

3d Printed Microfluidic Fabrication Methodology, Characterization, Mechanical Design, And Applications In Electrostatic Artificial Muscles And Benthic Microbial Fuel Cells, Terak B. Hornik

Master's Theses

The fabrication of microfluidic devices often requires specialized methods. The development of these methods requires careful characterization and understanding of the processes involved. Using primarily PolyJet 3D printing technology, microfluidics offers a wide scope of applications such as microfluidic benthic microbial fuel cells (MBMFCs) and electrostatic artificial muscles. MBMFCs benefit from the confinement of the microbes resulting in close proximity between the electrode and the organisms. Using a modular design called the Sponge, assembly and upscaling is possible. Electrostatic artificial muscles benefit from a microfluidic approach due to the non-linearity of electrostatic attraction creating disproportionate benefits when miniaturized. When designed …

Thermal Management For Optimal Performance Of Unitized Regenerative Fuel Cells, Mythy T. Tran

Mechanical & Aerospace Engineering Theses & Dissertations

As the race to net zero energy intensifies around the world, hydrogen production and fuel cell technologies are attracting more attention, and the technologies are growing rapidly. Together, hydrogen production and fuel cell technologies hold potential for a reliable, green, and sustainable energy system. Hydrogen is an excellent energy carrier and can be produced from various sources, especially green and renewable sources. Fuel cells generate electricity and water from hydrogen and oxygen. In reverse mode, fuel cells operate as electrolyzers to produce hydrogen and oxygen from electricity and water. However, the major drawback that keeps hydrogen and fuel cells from …

Necessity Of Education For Efficient And Sustainable Production And Consumption Of Energy In Tanzania, George Kahangwa

Tanzania Journal of Engineering and Technology (TJET)

This paper reports the findings of a study that was conducted in Tanzania to grasp how the policies, plans and curricula at different levels of education accommodate knowledge gathered on energy to support the fostering of energy education. The study interrogated what necessitates the inclusion of energy education into the curricula in Tanzania. Subscribing to a qualitative approach, the study employed a desk research method to review curricula and other documents guiding secondary and university level education in the country. The study found out that heightening people’s consumption of energy for domestic and industrial purposes constituted the main issue that …

A Country-Level Primary-Final-Useful (Cl-Pfu) Energy And Exergy Database: Overview Of Its Construction And 1971–2020 World-Level Efficiency Results, Paul E. Brockway, Matthew Kuperus Heun, Zeke Marshall, Emmanuel Aramendia, Paul Steenwyk, Thomas Relph, Michelle Widjanarko, Jeonghoo (James) Kim, Anjana Sainju, Julian Irtube

University Faculty Publications and Creative Works

Societal exergy analysis examines the flows of energy and exergy through societies, from primary (e.g. oil) to final (e.g. gasoline) to useful (e.g. propulsion) energy stages. By extending the study of energy to the useful stage, new insights into the under-represented role of energy in economic growth have been made. However, currently (a) country coverage is patchy and incomplete, (b) available data are based on varying methods and assumptions including efficiencies based on economic rather than engineering data, and (c) datasets are constructed using piecemeal computational approaches. To address these gaps, we construct a country-level primary-final-useful (CL-PFU) energy and exergy …

2024 Marine Energy Collegiate Competition, Nora Riedinger, Miles Mikkelsen, Brendan Stratford, Derek Tom, Zach Kwast, Harmon Yanikian-Sutton, Kennedy Urcelay, Tori Thomas, Brady Caron

Mechanical Engineering

PolyWave Energy is the second team from California Polytechnic University at San Luis Obispo to compete in the Marine Energy Collegiate Competition. PolyWave Energy consists of Mechanical Engineering, Electrical Engineering, and Business Administration students who have worked together from September 2023 to May 2024 on designing, building, and testing a marine power device to serve a selected market.

In response to the escalating concerns surrounding carbon emissions, climate change, and the depletion of fossil fuels, California Polytechnic State University’s Polywave Energy team has developed a sustainable and reliable energy source for Autonomous Underwater Vehicle (AUV) charging. Through extensive research of …

Estimation Of Useful-Stage Energy Returns On Investment For Fossil Fuels And Implications For Renewable Energy Systems, Emmanuel Aramendia, Paul E. Brockway, Peter G. Taylor, Jonathan B. Norman, Matthew K. Heun, Zeke Marshal;

University Faculty Publications and Creative Works

The net energy implications of the energy transition have so far been analysed at best at the final energy stage. Here we argue that expanding the analysis to the useful stage is crucial. We estimate fossil fuelsʼ useful-stage energy returns on investment (EROIs) over the period 1971–2020, globally and nationally, and disaggregate EROIs by end use. We find that fossil fuelsʼ useful-stage EROIs (~3.5:1) are considerably lower than at the final stage (~8.5:1), due to low final-to-useful efficiencies. Further, we estimate the final-stage EROI for which electricity-yielding renewable energy would deliver the same net useful energy as fossil fuels (EROI …

An Integrated Resource Planning Proposal For Tucson Electric Power, Valeria Bernal

Master's Projects and Capstones

An integrated resource plan (IRP) is crucial for utilities to determine the most cost-efficient energy resources while considering system reliability, environmental impact, and regulatory requirements. VitalsparK developed an IRP for Tucson Electric Power (TEP) to transition its current 70% thermal and 30% renewable energy portfolio, emitting 740 grams of CO2 per kWh, toward carbon neutrality by 2050. The proposed plan involves retiring existing infrastructure, adding 8 GW of renewable and storage capacity, and incorporating 2.5 GW of net-zero natural gas power plants. VitalsparK presented two scenarios: the Reference (REF) Case, which focuses on the least-cost portfolio to meet demand through …

Optimization Pump As Turbine Coupled To A Self-Excited Induction Generator Using Multi-Objective Genetic Algorithm, Emanuel J. Nyirenda

Tanzania Journal of Engineering and Technology (TJET)

As a way of accelerating the deployment of affordable and clean renewable energy generation technologies, applying a pump working as a turbine coupled to a self-excited induction generator is gaining popularity in various areas including energy recovery and micro hydro systems. However, it is currently challenging to predict the performance of the PAT-SEIG system and there is no agreed-upon rule on the selection of the appropriate system to be installed at a particular site. This paper has presented multi-objective optimization to select the best operating point of the PAT-SEIG system. The results show that the peak efficiencies for the PAT …

Optimal Load Shedding During Service Restoration In Electrical Secondary Distribution Network Based On Reinforcement Learning, Rukia J. Mwifunyi

Tanzania Journal of Engineering and Technology (TJET)

Increased stress in traditional power systems results in blackouts due to voltage instability attributed to a mismatch between available capacity and load demand, especially in distribution networks. Service restoration schemes are designed to return power supply to the affected parts of the networks. The availability of insufficient supply is a complex problem that requires operational experience or an automatic system. The stochastic nature of load demand significantly impacts service restoration as it results in increased restored demand in case a fault occurs during off-peak hours and helps reduce overload if the fault occurs during peak hours. The study adopts an …

An Optimization Tool For A Standalone Photovoltaic System, Johanes Kasilima

Tanzania Journal of Engineering and Technology (TJET)

Stand-alone photovoltaic systems (SAPV) are often used in remote areas where access to grid electricity is limited. This system depends on solar energy. However, Photovoltaic (PV) systems need a greater initial investment than conventional sources of energy, and their effectiveness is reliant on a number of environmental conditions such as the unpredictable solar radiation. One step in reducing the investment cost of a PV system is determining the optimal size of solar PV components that minimize costs. This paper presents a Particle Swarm based optimization tool for sizing Stand-alone PV systems. The optimization tool selects the optimal Levelized Cost of …

Quantum-Powered Battery Scheduling In Modern Distribution Grids, Diba Ehsani

Electronic Theses and Dissertations

The rising need for exploiting a novel and evolved computation is an increasing concern in the power distribution system to address the exponential growth of distribution-connected devices. Scheduling numerous battery energy storage systems in an optimal way is one of the emerging challenges that will be more noticeable as the number of batteries, including residential, community, and vehicle batteries, increases in the grid. This thesis focuses on this topic and offers a necessary component in building the quantum-compatible distribution system of the future. Using a constrained quadratic model (CQM) on D-Wave’s hybrid solver as well as a binary quadratic model …

Schaeffler Icvd Coating Machine, Louis Mcgrath

Williams Honors College, Honors Research Projects

Chemical Vapor Deposition (CVD) is mutual technology used to deposit thin film through a gaseous phase by vaporizing the solid materials. This conventional process usually requires high thermal stability of the materials, which is not applicable for most of the polymeric materials. Therefore, a novel process, initiated Chemical Vapor Deposition (iCVD) is developed by introducing the gaseous monument and initiator to form the thin film in-situ. By adjusting the free-radical polymerization in the vapor phase, a variety of thin and uniform polymer films can be achieved. Depending on the chemistry, iCVD has many categories. This report explains the design …

Employment Of Intelligent Predictive Maintenance On Thermal Power Plant Component Parts Taking Condenser Vacuum As A Case Study, Titus Ajewole

Tanzania Journal of Engineering and Technology (TJET)

This work proposes deployment of machine learning in the maintenance of individual constituent parts of steam power plant assemblages. With the condenser vacuum of a steam turbine (in a six-turbine plant assemblage) taken as a case study, information on the past operating parameters of the selected plant component was used to forecast its future working condition. Based on Exponential Gaussian Process of Regression, a model was developed, trained using the diachronic operational data, and employed in determining the future. A quantitative evaluation was employed to provide the distribution of the test values of the data about the lines of regression, …

Designing A Model Of Solar Photovoltaic Water Pumping System For Off-Grid Localities In Tanzania, Imani Mruma

Tanzania Journal of Engineering and Technology (TJET)

Modeling of photovoltaic (PV) water pumping system for rural water localities is vital especially in these modern days, in Tanzania. This is due to the rise of high number of solar-powered rural water projects constructed lacking appropriate design. The fate result into poor and substandard projects delivering below expectations. Kikombo Solar Water Project situated in Dodoma; Tanzania is one among poorly designed solar project chosen as a case study to validate proposed model. The main problem of Kikombo project is unsatisfactory amount of water from domestic points to satisfy population demand. This matter has been raised by pumping-station attendants and …

Renewable Energy Potential Assessment For Improving Electric Power Availability In Urban Area: A Case Of Msigani Ward In Ubungo Municipal, Tanzania, Respicius Kiiza

Tanzania Journal of Engineering and Technology (TJET)

The demand for electricity in urban areas of the developing countries like Tanzania is increasing rapidly due to factors such as increasing population, expansion of economic activities and industrialization. Msigani ward is one of the fourteen (14) administrative urban wards in Ubungo Municipal, Dar es Salaam, located at latitude 6.8031 oS and longitude 39.1188 oE. Recently, there has been observed increase in power demand in this ward. This in turn has caused a supply deficit that sometimes led to large number of interruptions caused by frequent power outage and load shedding. The total capacity of the national grid is limited …

Mppt Dc-Dc Buck-Boost Converter For Off Grid Hybrid Solar-Wind Battery System In Ikuza Island, Tanzania, Aviti Thadei Mushi

Tanzania Journal of Engineering and Technology (TJET)

Ikuza Island in Kagera-Tanzania faces lack of electricity due to cost challenges of extending the grid by marine cables and other transmission facilities. These makes such endeavour not appealing to the supply authority due to those higher charges. Therefore, this paper undertakes to design hybrid renewable energy sources for the island by specifically focusing on the buck-boost converter for the energy conversion from these renewable resources. The design of the bidirectional buck-boost converter for maximum power point tracking in off-grid hybrid renewable energy systems is multifaceted due to the inhomogeneity nature of the renewable energy sources. The bidirectional buck-boost converter, …

Aquaculture In Hydropower Reservoirs, Racheal Macharia

Tanzania Journal of Engineering and Technology (TJET)

There is an undoubtedly existing relationship between water, energy, and food and their interaction with the natural environment and mankind. Climate change is the talk of the day in global development discussions as it intensifies water shortages, energy, poverty, food shortages, and environmental degradation. Currently, most of the hydropower dams constructed in Africa are majorly built to store water for agricultural purposes, control flooding, and generate electricity. Notable projects include the seven forks hydropower stations located on the Tana River in Kenya; Aswan high dam in Egypt; Grand Renaissance dam in Ethiopia; Kariba dam in Zimbabwe and Akosombo in Ghana. …

Smart Grid In Tanzania: Research Opportunities, Aviti Thadei Mushi

Tanzania Journal of Engineering and Technology (TJET)

reinvigorated its power generation capacity significantly to ensure smooth execution of its industrialization agenda and cope with the fourth industrial revolution. To ensure reliable availability of power to sustain its growing economy, Tanzania embarked on a deliberated measure to forge an energy mix. This deliberate measure encompasses the use of renewable energy technologies such as wind, solar, biomass, wastes, and micro hydro; natural gas; and other energy sources which are locally available including coal and geothermal. To effectively and efficiently manage such a growing power system and make electricity accessible to all for higher levels of industrial investment and services, …

Isolation And Performance Test Of Green Low Dosage Hydrate Inhibitors From Local Materials For Improving Flow Assurance In Oil And Gas Industry, Makungu Madirisha

Tanzania Journal of Engineering and Technology (TJET)

The formation of gas hydrates in oil and gas industry can be minimized or prevented by the use of inhibitors. This paper reports on hemicellulose and modified lignin as low dosage gas hydrate inhibitors (LDGHIs). LDGHIs were isolated from sugarcane bagasse (SCB), plant gum exudates (PGE) of Acacia trees, and coconut coir, and further characterized by Attenuated Total Reflectance - Fourier Transform Infrared (ATR-FTIR) spectrometer, porosimeter and thermogravimetric analyzer (TGA). The PGE and SCB yielded 77.75% and 12.38% of hemicellulose, respectively, while coconut coir yielded 35.59% of lignin which was modified to sodium lignosulfonate (SLS) to improve its solubility in …

Experimental Investigation On Recovery Of Micro Hydropower Dump Load Through Oil Heating System, Joseph H. Kihedu Dr.

Tanzania Journal of Engineering and Technology (TJET)

Micro hydropower power generates electrical energy to meet connected electrical demand, that normally fluctuates causing imbalances. Electronic load controller is then used to balance power system by diverting surplus generated power to the dump load commonly resistive load such as bulk water heater. This study investigated use of oil heating system as a replacement for conventional resistive dump load. In comparison to water, oil has high thermal retention therefore can serve as good thermal media. Dump load range ranged between 17 kW to 78 kW. A 6-kW electrical heater was used for laboratory oil heating system from which heated oil …

The Modernization Of Large Power Transformer Tanks, Babajide O. Williams

Electronic Theses and Dissertations

Due to the current demands placed on the power grid in terms of climate change, increasing urbanization, and terrorist attacks, the U.S. government in response to these demands, mandated that all the grid components be modernized in order to increase their reliability. As a critical component of the grid, Large Power Transformers (LPTs) play a key role in ensuring sustainable power generation and distribution. A literature search performed in this work and the analysis of data retrieved from the search showed that the tanks of these LPTs are critical to their durability, longevity, and reliability. Therefore, the reliability of LPTs …

Power Thyristor Controller For Speed Control Of Dc Motor, Alejandra Zapata, Morgan Erich Boehme, Abdullah Mohammed Awidah, Payton Robert Chalstrom

Electrical Engineering

In this work, a Power Thyristor Controller for Speed Control of DC Motor has been developed with the purpose of replacing an existing simulation experiment, aiming to effectively implement the principle of learning by doing. The primary objective of the experiment setup is to illustrate the fundamental principles and operational mechanisms underlying the firing angle and controlled bridge rectifier. The new experiment is taking advantage of the existing FCRO4100 Single Phase Firing Board that was donated to the University by ENERPRO. The pre-programmed microcontroller is connected to the thyristor bridge rectifier that’s powered by 24VAC. Additionally, a DC motor will …

Design Of International Airport Hybrid Renewable Energy System, Aviti Thadei Mushi

Tanzania Journal of Engineering and Technology (TJET)

This paper presents the design and simulation of a hybrid renewable energy system utilizing solar and wind energy sources with a backup generator. The demand for reliable electric energy in support of investments in large social and economic development activities such as airport operations has been an agenda worldwide. In Tanzania, Mwanza International Airport (MIA) expects to consume about 18 MVA of electric power annually to support its operations for the next 25 years. About 78-80% of the world's commercial energy comes from fossil fuels. Non-renewable fuels and other negative effects contribute to global warming through greenhouse gas emissions and …