Electro-Mechanical Systems Commons^™

The Design, Fabrication, And Pressure Testing Of A Low-Temperature Co-Fired Ceramic Electric Propulsion Thruster, Derek J. Reis

Boise State University Theses and Dissertations

Electric thrusters have been used for many years for orbital station-keeping and propulsion. As technology advances, smaller satellites are possible that require less thrust. The resulting miniature electric thrusters need low-weight and compact designs. This thesis specifies the design, fabrication, and testing of a thruster and its fluid delivery system designed for use with a micro-satellite weighing less than fifty kilograms.

The advent of Micro-Electro-Mechanical Systems (MEMS) has sparked a new market with incredibly small scale designs. Using this technology with Low-Temperature Co-fired Ceramic (LTCC) materials has spawned the new distinction of Ceramic Micro-Electro-Mechanical Systems (C-MEMS). The thruster body is …

Development Of A Pdms Based Micro Total Analysis System For Rapid Biomolecule Detection, Balaji Srinivasan Venkatesh

Graduate Theses and Dissertations

The emerging field of micro total analysis system powered by microfluidics is expected to revolutionize miniaturization and automation for point-of-care-testing systems which require quick, efficient and reproducible results. In the present study, a PDMS based micro total analysis system has been developed for rapid, multi-purpose, impedance based detection of biomolecules. The major components of the micro total analysis system include a micropump, micromixer, magnetic separator and interdigitated electrodes for impedance detection. Three designs of pneumatically actuated PDMS based micropumps were fabricated and tested. Based on the performance test results, one of the micropumps was selected for integration. The experimental results …

Micro Grids Fabricated For Miniature Ion Thruster, Deborah French, Jesse Taff

College of Engineering Poster Presentations

Part of the research at Boise State is a miniaturized plasma propulsion thruster. The purpose of the thruster is to provide the necessary location realignments for small satellites in space. The grid creates an electrostatic field, which extracts plasma ions from an Inductively Coupled Plasma (ICP) source. The ions are propelled toward a collector plate being a second identical grid, which in turn creates the desired thrust. The size and density of the openings in the grid are essential to optimizing the thrust produced. The grid geometry contributes to the ion departure angle (focusing) and the ion transparency. The Stainless …

Universal Scaling And Intrinsic Classification Of Electro-Mechanical Actuators, Sambit Palit, Ankit Jain, Muhammad A. Alam

Birck and NCN Publications

Actuation characteristics of electromechanical (EM) actuators have traditionally been studied for a few specific regular electrode geometries and support (anchor) configurations. The ability to predict actuation characteristics of electrodes of arbitrary geometries and complex support configurations relevant for broad range of applications in switching, displays, and varactors, however, remains an open problem. In this article, we provide four universal scaling relationships for EM actuation characteristics that depend only on the mechanical support configuration and the corresponding electrode geometries, but are independent of the specific geometrical dimensions and material properties of these actuators. These scaling relationships offer an intrinsic classification for …

Digitally Programmable Rf Mems Filters With Mechanically Coupled Resonators, Hengky Chandrahalim, Sunil Ashok Bhave

AFIT Patents

A digitally-tunable RF MEMS filter includes a substrate and a plurality of mechanically coupled resonators, wherein a first and a last resonator of the plurality of mechanically coupled resonators are configured to be electrostatically transduced. One or more of the plurality of mechanically coupled resonators are configured to be biased relative to the substrate such that the one or more biased resonators may be brought substantially in contact with the substrate. In a method of digitally tuning an RF MEMS filter having a mechanically coupled resonator array, a DC bias voltage is applied to at least a first resonator and …

Trajectory Generation For Stair Ascent Walking Using Rayleigh Oscillator, T. Afzal, Andrew B. Wright, Kamran Iqbal

Journal of the Arkansas Academy of Science

This paper describes a trajectory generation technique for stair-ascent walking. The knee, hip and ankle joint trajectory during stair ascent are generated using mutually coupled, nonlinear oscillators. The parameters of the oscillators are tuned using the harmonic balance method, which converts the nonlinear differential equations to a set of algebraic equations. Fourier analysis of data generated by stair-ascent walking is performed to extract the amplitude and the phase of the dominant frequency components for each joint trajectory. The solution for the oscillator is assumed to be a sinusoidal wave and then by harmonic balance method the parameters of the oscillator …

The Effect Of Isostatic Pressing On The Dielectric Properties Of Screen Printed Ba0.5Sr0.5Tio3 Thick Films, Siwei Wang, Lingling Zhang, Jiwei Zhai, Fanglin Chen

Faculty Publications

Ba_0.5Sr_0.5TiO₃ thick films with B₂O₃–Li₂O glass sintering aid were prepared by the screen printing method on Al₂O₃ substrates. A 200 MPa isostatic pressure was applied to the films before sintering. After being sintered at 950^∘C, lower porosity and denser microstructure was obtained compared with the films without isostatic pressing. The dielectric constant and dielectric loss were 238 and 0.0028, respectively. A tunability of 61.7% was obtained for the isostatic pressed films, a 27.8% enhancement compared to unpressurized films. These results suggest that isostatic pressing …

Experimental Investigation To Inform Optimal Configurations For Dynamic Near-Field Passive Uhf Rfid Systems, Donnie E. Proffitt Ii

Theses and Dissertations--Mechanical and Aerospace Engineering

RFID has been characterized as a “disruptive technology” that has the potential to revolutionize numerous key sectors. A key advantage of passive RFID applications is the ability to wirelessly transmit automatic identification and related information using very little power. This paper presents an experimental investigation to inform the optimal configuration for programming passive ultra-high frequency (UHF) RFID media in dynamic applications. Dynamic programming solutions must be designed around the tag’s functionality, the physical programming configuration and environment. In this investigation, we present a methodology to determine an optimal configuration to maximize the systems programming efficiency for dynamic applications.

Mode And Implementation Of A Hybrid Control System For A 2-Mode Hybrid Electric Vehicle, Zhenhua Zhu

Graduate Theses, Dissertations, and Problem Reports (ETD)

Automotive transportation consumes more than 71% of the world's total petroleum energy. The vehicle will have to use less because it will take less than 30 years to consume the rest of the proven conventional oil reservoir if the fuel consumption keeps the current trend. One of the methods to improve the vehicle efficiency is to develop Hybrid Electric Vehicle (HEV). An HEV combines an internal combustion engine (ICE) and electric motor(s) powered by batteries or capacitors to achieve better fuel economy. Among the HEVs, 2-Mode HEV combines an ICE and two electric motors with two planetary gear sets and …

Project Haiti 2012: Providing An Experiential Learning Experience Through The Design And Delivery Of A Water Purifier In Haiti, Yung Wong, Johnathon Camp, Shavin Pinto, Kyle Fennesy, Marc Compere, Yan Tang

Publications

In this paper, we share our experiences and lessons learned from Project Haiti 2012, a project to design and install a water purification system serving 20,000 people per day in the largest tent city in Haiti. Project Haiti 2012 was the third and largest system we have built for Haitians and represents a huge success for all participants and stakeholders. This paper discusses the unique experiential learning opportunity involved in the design and delivery of the water purifier in a foreign developing country. Multiple positive educational, social, and economic outcomes were achieved including students applying knowledge gained from coursework towards …