Electro-Mechanical Systems Commons^™

Assessment Of The Impacts Of Climate Variability On Hydropower Generation: A Case Study Of The New Pangani Falls, Tanzania, Dativa Byarufu

Tanzania Journal of Engineering and Technology (TJET)

Climate change poses potential impacts on hydropower generation either positively by increasing or negatively by decreasing river flow. This study assessed the impacts of climate variability on hydropower with a focus on the New Pangani Falls in Tanzania. Rainfall and temperature time series data from 1980-2014 were analyzed in relation to river discharge and associated impacts to hydropower generation. The Man-Kendall test was used to detect trend in both annual and seasonal time series. The results showed a negative trend in annual rainfall with Z= -2.41 at α = 0.05 and the slope Q = -0.964. Seasonal trend analysis showed …

Resistive Switching In Fto/Cuo-Cu2o/Au Memory Devices, Amir Shariffar, Haider Salman, Tanveer A. Siddique, Wafaa Gebril, M. Omar Manasreh

Electrical Engineering Faculty Publications and Presentations

Memristors are considered to be next-generation non-volatile memory devices owing to their fast switching and low power consumption. Metal oxide memristors have been extensively investigated and reported to be promising devices, although they still suffer from poor stability and laborious fabrication process. Herein, we report a stable and power-efficient memristor with novel heterogenous electrodes structure and facile fabrication based on CuO-Cu2O complex thin films. The proposed structure of the memristor contains an active complex layer of cupric oxide (CuO) and cuprous oxide (Cu2O) sandwiched between fluorine-doped tin oxide (FTO) and gold (Au) electrodes. The fabricated memristors demonstrate bipolar resistive switching …

Experimental Investigation Of The Wind Energy Harvesting Potential Of A Stand-Alone Piezoelectric Strip, Phillip Christopher Scott

Mechanical Engineering ETDs

The purpose of the study was to investigate the feasibility of harvesting wind energy on a small scale in residential areas. The method investigated was the initiation of movement-induced excitation (MIE), a type of aeroelastic flutter, within samples of polyvinylidine fluoride (PVDF), a piezoelectric polymer. Single samples of PVDF were secured in a wind tunnel and sample voltage was measured over a broad range of wind speeds. Power was calculated then via the addition of ohmic resistance matched to the magnitude of the capacitive impedances of the samples. The geometry of the PVDF samples studied was maintained as a simple …

Performance Analysis Of Renewable Energy Resources In Rural Areas: A Case Study Of Solar Energy, Jackson Justo

Tanzania Journal of Engineering and Technology (TJET)

This paper presents an overview of the recent development trends of solar photovoltaic (PV) systems and the performance in the Tanzanian context. The two types of solar power generation that are considered in this paper are: i) solar PV systems and ii) concentrated solar power (CSP). The two are compared in terms of cost of energy and energy storage mechanism. Moreover, the effect of ambient temperature on the solar PV module is analyzed. In addition, a detailed analysis on using solar axis tracking to increase the power generation is also presented. The extent to which the cell surface temperature and …

Dartmouth Formula Racing: Full Electric Battery System Design, Matt Gardner, Jacob Hagler, Ruthie Nordhoff, Otto Salmi

ENGS 89/90 Reports

Dartmouth Formula Racing (DFR) lacked an electrical energy storage system that was Formula Hybrid rules-compliant, optimized for FH events, safe, reliable, and integrated with the rest of their vehicle. Additionally, the team lacked the academic and professional resources required to bring a thorough, analytical approach to the design, testing, and documentation of the new storage system. Our team designed and built a Lithium-Ion battery pack (accumulator) containing energy storage, active cooling, battery management and temperature monitoring systems, and control circuitry compatible with DFR’s vehicle. Collaboration throughout design, fabrication, assembly and testing processes ensured effective knowledge transfer to the DFR team.

Dual-Axis Solar Tracker, Bryan Kennedy

All Undergraduate Projects

Renewable energies, and fuels that are not fossil fuel-based, are one of the prolific topics of debate in modern society. With climate change now becoming a primary focus for scientists and innovators of today, one of the areas for the largest amount of potential and growth is that of the capturing and utilization of Solar Energy. This method involves using a mechanical system to track the progression of the sun as it traverses the sky throughout the day. A dual-axis solar tracker such as the one designed and built for this project, can follow the sun both azimuthally and in …

The Potentials Of Faecal Sludge Treatment Using Local Conditioners In Tanzania: A Review, Doglas Benjamin1

Tanzania Journal of Engineering and Technology (TJET)

Worldwide, every day human beings generate millions of tons of Faecal Sludge (FS), which is rich in water, nutrients, energy, and organic compounds. Yet FS is not being managed in a way that permits us to derive value from its reuse, while at the same time, millions of farmers struggle with depleted soils and lack of water. In most of the developing countries, energy for cooking is mainly derived from cutting of trees, either as wood or charcoal. Resource recovery and reuse from FS can create livelihoods, enhance food security, support green economies, reduce waste and contribute to cost recovery …

Heat: Hydraulic And Electric Animation Team, Tyler J. Couvrette, Michael J. Cain, Sara T. Novell, Dexter K. Yanagisawa

Mechanical Engineering

Each New Years’ Day, the Cal Poly Rose Float presents a flower-covered float to the world at the Tournament of Roses parade. This floral display, paired with moving mechanical animations, shows off Cal Poly to the world. This project strove to keep Cal Poly on the cutting edge of technology both in parade floats, and in engineering, by creating a completely electric-powered animation system.

To accomplish this, a group of students set out to make the fully electric animation system that can power both the hydraulic and electric mechanisms on the Float. This was accomplished through months of planning and …

Optimal Power Flow Control Of Networked Dc Microgrids, Eddy H. Trinklein

Dissertations, Master's Theses and Master's Reports

The US military is moving toward the electrification of many weapon systems and platforms. Advanced weapon systems such as high energy radar, electro-magnetic kinetic weapons and directed energy pose significant integration challenges due to their pulsed power electrical load profile. Additionally, the weapons platforms, including ships, aircraft, and vehicles can be studied as a mobile microgrids with multiple generation sources, loads, and energy storage. There is also a desire to extend the mission profile and capabilities of these systems. Common goals are to increase fuel efficiency, maintaining system stability, and reduce energy storage size as typically required to enable pulsed …

Networked Microgrid Optimization And Energy Management, Robert S. Jane

Dissertations, Master's Theses and Master's Reports

Military vehicles possess attributes consistent with a microgrid, containing electrical energy generation, storage, government furnished equipment (GFE), and the ability to share these capabilities via interconnection. Many military vehicles have significant energy storage capacity to satisfy silent watch requirements, making them particularly well-suited to share their energy storage capabilities with stationary microgrids for more efficient energy management. Further, the energy generation capacity and the fuel consumption rate of the vehicles are comparable to standard diesel generators, for certain scenarios, the use of the vehicles could result in more efficient operation. Energy management of a microgrid is an open area of …

Development Of A Rapid Fatigue Life Testing Method For Reliability Assessment Of Flip-Chip Solder Interconnects, Cody Jackson Marbut

Graduate Theses and Dissertations

The underlying physics of failure are critical in assessing the long term reliability of power packages in their intended field applications, yet traditional reliability determination methods are largely inadequate when considering thermomechanical failures. With current reliability determination methods, long test durations, high costs, and a conglomerate of concurrent reliability degrading threat factors make effective understanding of device reliability difficult and expensive. In this work, an alternative reliability testing apparatus and associated protocol was developed to address these concerns; targeting rapid testing times with minimal cost while preserving fatigue life prediction accuracy. Two test stands were fabricated to evaluate device reliability …

Comparative Study Of Power Semiconductor Devices In A Multilevel Cascaded H-Bridge Inverter, Kenneth Mordi

Graduate Theses and Dissertations

This thesis compares the performance of a nine-level transformerless cascaded H-bridge (CHB) inverter with integrated battery energy storage system (BESS) using SiC power MOSFETs and Si IGBTs. Two crucial performance drivers for inverter applications are power loss and efficiency. Both of these are investigated in this thesis. Power devices with similar voltage and current ratings are used in the same inverter topology, and the performance of each device is analyzed with respect to switching frequency and operating temperature. The loss measurements and characteristics within the inverter are discussed. The Saber® simulation software was used for the comparisons. The power MOSFET …

Hosting Capacity Optimization In Modern Distribution Grids, Mansoor T. Alturki

Electronic Theses and Dissertations

The availability of distributed renewable energy resources and the anticipated increase in new types of loads are changing the way electricity is being produced and supplied to consumers. This shift is moving away from a network delivering power solely from centralized power plants towards a decentralized network which supplements its power production by incorporating local distributed generators (DGs). However, the increased integration of DGs into existing distribution networks is impacting their behavior in terms of voltage profile, reliability, and power quality. To determine the maximum amount of DG that distribution grids can accommodate the concept of hosting capacity is introduced. …

Electrowetting Using A Microfluidic Kelvin Water Dropper, Elias Yazdanshenas, Qiang Tang, Xiaoyu Zhang

Mechanical & Aerospace Engineering Faculty Publications

The Kelvin water dropper is an electrostatic generator that can generate high voltage electricity through water dripping. A conventional Kelvin water dropper converts the gravitational potential energy of water into electricity. Due to its low current output, Kelvin water droppers can only be used in limited cases that demand high voltage. In the present study, microfluidic Kelvin water droppers (MKWDs) were built in house to demonstrate a low-cost but accurately controlled miniature device for high voltage generation. The performance of the MKWDs was characterized using different channel diameters and flow rates. The best performed MKWD was then used to conduct …

Ball Oscillating Bouncer, Eric Blok, Daniel Altemese, Ryan Nowacki, Maram Qurban

Williams Honors College, Honors Research Projects

The purpose of this report is to document the need, objectives, marketing and engineering requirements, as well as validate the design of an autonomous control device capable of continuously bouncing a table tennis ball on a paddle. This includes the design of a self correcting system using lightweight materials, and as few sensors and components as possible to achieve a compact, portable design. To accomplish this, the system is designed to react to a ball falling from as short a distance as 10 centimeters above the paddle, meaning all sensor processing, control processing, and motor drives should be able to …

Flexible Custom Electric Skateboard, Caleb Adam Kelsay

Electrical Engineering

At Cal Poly traveling long distances only accessible by foot such as across campus or from the car park to class can be tiring and time-consuming. While not physically demanding, the trek consumes time in our tight college life schedule. To improve our time efficiency this project provides a relatively lightweight, powered solution to quickly and effectively travel long distances while maintaining full control and safety even on hills, a current limitation of traditional skateboards.

This electric skateboard includes the battery capacity to travel all around campus on a single charge with a compact and flexible skateboard design that provides …

Marine Gastrobot Final Design Report, Wesley B. Williams, Eric Kane Dreischerf, Tommy Nicholas Yath

Mechanical Engineering

The Marine Gastrobot sponsored by Dr. Christopher Kitts of the Cal Poly Center for Applications in Biotechnology was a research and development effort intended to explore the use of microbial fuel cell technology as a power source for underwater robots. Our team Ocean Locomotion succeeded in developing a first iteration of an underwater robotic platform suitable for microbial fuel cell integration. The primary feature of the design is its sinusoidal fin propulsion intended for benthic exploration with limited risk of entanglement. During the course of development, Ocean Locomotion explored the use of low power actuation methods and determined their limited …

System-Layout-Dependent Thermally Induced Solder Stress & Reliability Implications, Ange C. Iradukunda

Mechanical Engineering Undergraduate Honors Theses

Electronic flip chip assemblies consist of dissimilar component materials, which exhibit different CTE. Under thermal cyclic operating conditions, this CTE mismatch produces interfacial and interconnect stresses, which are highly dependent on system layout. In this paper, sensitivity analyses are performed using ANSYS FEA to establish how the proximity and arrangement of neighboring devices affect interconnect stress. Flip chip alignment modes ranging from edge-to-edge to corner-to-corner are studied. Results of these FEA studies, demonstrated that closely packing devices together has the effect of making them act as one. This results in a significant increase in the thermomechanical stresses induced on peripheral …

Hybrid Diesel-Electric Drivetrain For Small Agricultural Field Machines, Joseph Jackson, Joseph S. Dvorak

Biosystems and Agricultural Engineering Faculty Publications

In this project, a series electric drivetrain sized for small agricultural machinery was developed and tested. Electric drives have noted benefits in simplicity, controllability, integration with other electronics such as those that provide autonomous action, and in efficiency over a wide operating range. Their biggest drawback for agricultural use is the limited capacity of electrical energy storage. A series hybrid drivetrain provides a method to overcome these capacity constraints through the use of chemical energy storage. The series hybrid drivetrain in this research was designed using well-established components. It consisted of a diesel-electric generator, a lead acid battery pack, a …

Electromechanics Of An Ocean Current Turbine, Vasileios Tzelepis

LSU New Orleans Theses and Dissertations

The development of a numeric simulation for predicting the performance of an Ocean Current Energy Conversion System is presented in this thesis along with a control system development using a PID controller for the achievement of specified rotational velocity set-points. In the beginning, this numeric model is implemented in MATLAB/Simulink® and it is used to predict the performance of a three phase squirrel single-cage type induction motor/generator in two different cases. The first case is a small 3 meter rotor diameter, 20 kW ocean current turbine with fixed pitch blades, and the second case a 20 …

Modeling And Test Of The Efficiency Of Electronic Speed Controllers For Brushless Dc Motors, Clayton R. Green

Master's Theses

Small electric uninhabited aerial vehicles (UAV) represent a rapidly expanding market requiring optimization in both efficiency and weight; efficiency is critical during cruise or loiter where the vehicle operates at part power for up to 99% of the mission time. Of the four components (battery, motor, propeller, and electronic speed controller (ESC)) of the electric propulsion system used in small UAVs, the ESC has no accepted performance model and almost no published performance data. To collect performance data, instrumentation was developed to measure electrical power in and out of the ESC using the two wattmeter method and current sense resistors; …

Veloelectric: Creating A Device That Harvests Energy From Bicycles, Austin Hall, Daniel Stohr, Tj Fox

Mechanical Engineering

Long distance mountain bikers, bike-packers, and many bikers in developing countries rely on electrical devices for safety and communication. These specific groups of people operate in areas with little to no electricity, and often times have no power to sustain their devices. The purpose of this Cal Poly senior project, VeloElectric, was to design, build, and test a kinetic energy harvester for bicycles that can be used to charge common mobile devices via USB. This senior project team created a device that attaches directly to a bicycle and uses vibrations to generate energy, which in turn powers a variety of …

A Platinum Nanowire Network As A Highly Effective Current Collector For Intermediate Temperature Solid Oxide Fuel Cells, Hanping Ding, Xingjian Xue

Faculty Publications

We report the fabrication and evaluation of a platinum nanowire network as a highly efficient current collector for solid oxide fuel cells (SOFCs). The ink of carbon-black supported platinum nanoparticles was sprayed onto the cathode. After firing, the carbon black was oxidized and disappeared as carbon dioxide gas while the platinum nanoparticles connect with one another, forming a tree-branch-like nanowire network. The diameters of the nanowires range from 100 nm to 400 nm. Compared to a conventional platinum paste current collector, the polarization resistance of the PrBaCo₂O_5+δ (PBCO) cathode with a nanowire current collector was reduced …

Modeling Of Chemical-Mechanical Couplings In Anode-Supported Solid Oxide Fuel Cells And Reliability Analysis, Xinfang Jin, Xingjian Xue

Faculty Publications

Oxygen ionic transport in conducting ceramics is an important mechanism enabling solid oxide fuel cell (SOFC) technology. The multi-physicochemical processes lead to the fact that the distribution of oxygen vacancy site fraction is not uniform in a positive-electrode electrolyte negative-electrode (PEN) assembly. Different oxygen vacancy concentrations induce different volumetric expansion of ceramics, resulting in complicated chemical–mechanical coupling phenomena and chemical stress in SOFCs. In this research, a mathematical model is developed to study oxygen ionic transport induced chemical stress in an SOFC. The model is validated using experimental polarization curves. Comprehensive simulations are performed to investigate chemical stress distribution in …

Low Speed Alternator Design, Scott Merrick

Electrical Engineering

No abstract provided.

Micro Hydropower System, Christpher Neally, Ian Verstuyft

Electrical Engineering

The micro hydropower project strives to meet the needs of a specific village in northern Thailand in partnership with Engineers Without Borders. Specifically, the electrical side of the system must be designed to convert the mechanical power of a flowing river that is turning a turbine into sustainable and dependable power. Currently available hydropower systems will be considered, analyzed, and tailored to suit the specific needs of the community in need. The system to be designed will be flexible enough to demonstrate proof-of-concept with the limited maximum generable power in lab while having the ability to be easily scaled for …

Wind And Hydroelectric Power Simulation For The Dc House Project, Randy Lormand, Christopher Goloskie

Electrical Engineering

This project details the design and integration of a wind and hydroelectric power simulation system in correlation with the DC House Project. The simulator uses variable speed drives to rotate a DC motor which then drives a generator to produce output. This output is then regulated using a DC to DC converter which holds the voltage level constant making it easier to interface with other power sources for the house. The test results indicate that the simulator will be able to produce two separate power outputs that will provide at least 70 Watts of power in the acceptable speed range …

Swing Human Powered Generator: For The Dc House Project, Juan Vicente Avelar, Juan Jose Galindo, Juan Pramyr Ramos

Electrical Engineering

The Play Park Human Powered Generator project addresses various ways of generating power. More specifically, this project entails the design and construction of the Swing Power Generator to provide electrical power from mechanical energy. The swing generator will eventually be used as part of the human-powered generators utilized in the DC House project.

A swing generator prototype was built for this project, which demonstrates the feasibility of its use for electrical power source. Detailed design and construction of the swing generator is presented in this report along with results from hardware testing.

Design, Fabrication, And Testing Of An Emr Based Orbital Debris Impact Testing Platform, Jeffrey J. Maniglia Jr.

Master's Theses

This paper describes the changes made from Cal Poly’s initial railgun system, the Mk. 1 railgun, to the Mk. 1.1 system, as well as the design, fabrication, and testing of a newer and larger Mk. 2 railgun system. The Mk. 1.1 system is developed as a more efficient alteration of the original Mk. 1 system, but is found to be defective due to hardware deficiencies and failure, as well as unforeseen efficiency losses. A Mk. 2 system is developed and built around donated hardware from the Naval Postgraduate School. The Mk. 2 system strove to implement an efficient, augmented, electromagnetic …

Micro Modeling Study Of Cathode/Electrolyte Interfacial Stresses For Solid Oxide Fuel Cells, Xinfang Jin, Xingjian Xue

Faculty Publications

Delamination of the cathode/electrolyte interface is an important degradation phenomenon in solid oxide fuel cells (SOFCs). While the thermal stress has been widely recognized as one of the major reasons for such delamination failures, the role of chemical stress does not receive too much attention. In this paper, a micro-model is developed to study the cathode/electrolyte interfacial stresses, coupling oxygen ion transport process with structural mechanics. Results indicate that the distributions of chemical stress are very complicated at the cathode/electrolyte interface and show different patterns from those of thermal stress. The maximum principal stresses take place at the cathode/electrolyte interface …