Electro-Mechanical Systems Commons^™

Techno-Economic Analysis Of The Utilization Of Waste-To-Energy In Jakarta Industrial Estate Pulogadung, Wahyu Punjung Pesonagrata, Mohammad Akita Indianto

Journal of Materials Exploration and Findings

Indonesia has a serious waste problem, which ranking second in marine pollution. Due to significant environmental impacts, a solution to overcome the complexity of waste problems is needed. This study took sample on waste management in Jakarta Industrial Estate Pulogadung (JIEP). JIEP is an Industrial area which covers 443 hectares of land in East Jakarta. This study aims to address Indonesia's serious waste problem by exploring the potential utilization of waste in the Jakarta Industrial Estate Pulogadung (JIEP) as Refuse-Derived Fuel (RDF) for a waste-to-energy (WtE) power plant. The proposed method used a steam power plant with RDF as fuel …

Me3329 Modular Phonograph Gearbox, Garrett Andrik Leighton, Preston Robert Hupe, Gavin Carter Ebner, Andrew Renato Reyes

Mechanical Engineering

The Mechanical Engineering Department at California Polytechnic State University, San Luis Obispo (Cal Poly), seeks to develop a laboratory tool allowing students to reinforce concepts of gears for Mechanical Systems Design (ME329). Some current laboratories do not provide students with hands-on interaction, and the department lacks equipment and documentation to support a standardized lab. With ME329 expanding from ten to fifteen weeks, there is an opportunity to create a physical gearbox design lab allowing students to reinforce lecture material in engaging ways, while standardizing student learning. This senior project is presented and sponsored by Professor Alan Zhang. It will be …

Automation And Habitat Development For A Space Based Marine Life Environment, Logan Trimmer, Alexander Hang

Harrisburg University Other Works

This project was a cross-collaboration between the Environmental Sciences and Advanced Manufacturing and Robotics programs for the company Monolith Space.

The goal of this project was to design an autonomous system to be able to track qualities of water in an aquaculture system designed to be sent to space.

Calibration Of Measurement Tools In The Experimental Test Rig For Hydropower Performance Evaluation, Ombeni J. Mdee

Tanzania Journal of Engineering and Technology (TJET)

The demonstration of a typical hydropower plant requires the development of a test rig with the installation of tools to measure the performance parameters. The measurement tools require a calibration process to improve the quality of recorded data. This study involved the calibration of traditional and automated measurement tools connected to the hydropower test rig through an Arduino microprocessor. The automated measurement tools included a pressure transducer, flow meter, digital tachometer, and torque transducer, while traditional measurement tools, including a pressure gauge, concrete water tank, contact tachometer, and force lever arm balance, were connected in the same test rig during …

Towards Metrology 4.0 In Developing Countries’ Manufacturing Industries, Jailos Nzumile

Tanzania Journal of Engineering and Technology (TJET)

A systematic literature review was conducted to unveil the status of the digital transformation of metrology in developing countries, as they are lagging in utilising fourth industrial revolution (IR4.0) technologies to transform manufacturing industries. A PRISMA technique was employed using various keywords to identify, screen, and select the relevant literature. Forty publications were selected for the review, mainly discussing IR 4.0 technologies in metrological operations. The results indicate that the digital transformation of metrology has yet to be initiated in developing countries. However, the employment of IR4.0 technologies in advancing metrological operations in manufacturing industries is mostly discussed in the …

Effects Of Cutting Conditions On Tool Temperature And Material Removal Rate In Turning Operations, Simon I. Marandu

Tanzania Journal of Engineering and Technology (TJET)

Cutting conditions in manufacturing processes have effects on tool temperature and material removal rate. The objective of this study was to investigate the effects of cutting conditions namely spindle speed, feed rate, depth of cut and tool nose radius on tool temperature and material removal rate in turning operations. A total of 81 experiments were conducted to measure tool temperature and material removal rate in order to determine the effects of cutting conditions on tool temperature and material removal rate using ANOVA and regression analysis. The results show that tool nose radius, depth of cut, and spindle speed are significant …

Potential Use Of Pump As Turbine Coupled To Self-Excited Induction Generator For Micro-Hydro Cooking And Cooling Applications, Emanuel J. Nyirenda

Tanzania Journal of Engineering and Technology (TJET)

Clean cooking and efficient cooling in developing countries have recently become areas of great focus. Further, the environmental impact of flooding in high-capacity hydroelectric plants has become a major concern. As a result, there is growing emphasis on developing sustainable and decentralized energy solutions, focusing on the potential of micro-hydro systems, especially in rural and remote areas. Although there are several alternative energy generation methods, their application is not straightforward. One of the latest technologies under research is using pumps as turbines coupled to an induction generator. This paper explores through a rigorous experimental approach the possibility of using a …

Cellulose Recovery From Waste Denim Fabrics Through Indigo Vat Dye Reduction And Spandex Dissolution, Tito N. Venance

Tanzania Journal of Engineering and Technology (TJET)

This study addresses environmental conservation by tackling end-of-life management for post-consumer denim garments through the recycling of cotton fibres from waste denim. The purification process involved dithionite reduction of vat dyes in the presence of an alkali followed by selective dissolution of spandex using N,N-dimethylformamide (DMF). Optimal conditions for dye removal were determined at 90°C for 120 minutes with sodium hydroxide at 25 g/L, sodium dithionite at 6 g/L and PVP at 4.5 g/L, while spandex extraction was achieved using a 5% DMF solution at 70°C for 4 hours. Ultraviolet (UV)-vis spectrophotometric analysis indicated a significant increase in whiteness (DL*). …

Application Of Artificial Neural Network Models For Predicting Diesel And Petrol Prices In The Geographically Sparsed Regions In Tanzania, John M. Kafuku

Tanzania Journal of Engineering and Technology (TJET)

Fuel consumption in Tanzania, mainly diesel and petrol, accounts for 82 percent of the energy consumption in the country, with significant price volatility affecting market stability, availability of fuel, and investment decisions. This study uses an artificial neural network (ANN) with a backpropagating algorithm to predict fuel prices in four regions of Tanzania. Key input parameters include the currency inflation rate (CIR), the petrol fuel inventory (PFI), the diesel fuel inventory (DFI), and the fuel transport costs (FTC). The study selected the 6-10-10-2 ANN structures for Sumbawanga-Rukwa, Mpanda-Katavi, and Mbeya-Mbeya as well as 6-10-9-2 for the Songea-Ruvuma region. The results …

Factors Affecting Adoption Of Industry 4.0 Predictive Maintenance By Manufacturing Industries: Tanzania Food And Beverage Manufacturing Industries, Fred E. Peter

Tanzania Journal of Engineering and Technology (TJET)

Industry 4.0 has increasingly become a focal point of scholarly inquiry. Nonetheless, there remains a noticeable lack of comprehensive research on the diverse and systematic factors that influence the adoption of Industry 4.0 Predictive Maintenance (PdM 4.0) in manufacturing sectors within developing regions, particularly in East Africa. This study seeks to bridge this research gap by investigating the key determinants affecting the actual implementation of PdM 4.0 in Tanzania’s food and beverage manufacturing industries. To achieve this objective, a mixed-methods research design was adopted, combining both qualitative and quantitative approaches. Qualitative data were obtained through in-depth interviews with ten industry …

Heavy Metals Pollution In Roadside Ecosystems, Lilian Matafu

Tanzania Journal of Engineering and Technology (TJET)

Heavy metals refer to metallic elements that are characterized by having a relatively high density and they are toxic or poisonous even at low concentration. They are environmental pollutant owing to toxicity and longevity in atmosphere and ability to accumulate in living things via bioaccumulation. They tend to enter in different system such as food chain. Analyses of water, soil sediment and the surrounding growing plants (Cynodon dactylon and Cyperus species) for selected heavy metals (Cd, Pb, Zn and Cu) were conducted on a roadside pond located at Boko MSB, Dar es Salaam. Pond water, soil sediments and plant samples …

3d Printed Microfluidic Fabrication Methodology, Characterization, Mechanical Design, And Applications In Electrostatic Artificial Muscles And Benthic Microbial Fuel Cells, Terak B. Hornik

Master's Theses

The fabrication of microfluidic devices often requires specialized methods. The development of these methods requires careful characterization and understanding of the processes involved. Using primarily PolyJet 3D printing technology, microfluidics offers a wide scope of applications such as microfluidic benthic microbial fuel cells (MBMFCs) and electrostatic artificial muscles. MBMFCs benefit from the confinement of the microbes resulting in close proximity between the electrode and the organisms. Using a modular design called the Sponge, assembly and upscaling is possible. Electrostatic artificial muscles benefit from a microfluidic approach due to the non-linearity of electrostatic attraction creating disproportionate benefits when miniaturized. When designed …

Capacitive Sensors With Ultra-Small Capacitance For Smart Measurement And Control Systems, Rustam Baratov, Farrux Jabbor O'G'Li Ko'charov

Chemical Technology, Control and Management

This article discusses methods of low capacitance measurement of capacitive sensors. The results of the study of the amplitude-frequency (AF) and phase-frequency (PF) response of measurement circuits of capacitive sensors for low capacitances measurement, consisting of RC - differentiating elements are presented. The input and output parameters of the differentiating circuit and the complex transfer function are analyzed. The research results show that low capacitances measurement by measuring the rectangular pulses duration is the most effective measurement method.

Towing Tank Trials Of Hydrokinetic Turbine Scale Model To Support Marine Energy System Verification, Shahab Rouhi

LSU New Orleans Theses and Dissertations

In response to the escalating demand for sustainable energy solutions and the critical reevaluation of conventional fossil fuels due to environmental concerns, this dissertation embarks on a comprehensive exploration of hydrokinetic energy as a promising alternative. The study delves into the underexplored domain of hydrokinetic energy, leveraging innovative methodologies for effective utilization and harnessing, particularly through the development and investigation of hydrokinetic turbines.

In the realm of hydrokinetic energy conversion, our research has exclusively concentrated on horizontal-axis turbines, distinct from other turbine configurations. Noteworthy is the adaptation of a conventional horizontal-axis wind turbine for water currents, revealing enhanced performance through …

Cal Poly Fluid Power Vehicle Challenge 2024, J. Mason Gray, Ryan D'Amour, Alberto Acho Lopez, Christian Ferrandino, Johnathan Dietz

Mechanical Engineering

In this Final Design Review, the Cal Poly Fluid Power Vehicle Team competed in Norgren’s 2024 Fluid Power Vehicle Challenge. The design need of the competition was for college teams to compete with human-powered, hydraulic-driven vehicles in an endurance race, a sprint race, an efficiency race, and a regenerative power race. The competition need was to design a vehicle to win in as many races as possible, achieving the highest overall score and winning the competition. With a design emphasis on the endurance and sprint race, the Cal Poly team designed a fluid power system that fastened to a purchased …

Optimization Pump As Turbine Coupled To A Self-Excited Induction Generator Using Multi-Objective Genetic Algorithm, Emanuel J. Nyirenda

Tanzania Journal of Engineering and Technology (TJET)

As a way of accelerating the deployment of affordable and clean renewable energy generation technologies, applying a pump working as a turbine coupled to a self-excited induction generator is gaining popularity in various areas including energy recovery and micro hydro systems. However, it is currently challenging to predict the performance of the PAT-SEIG system and there is no agreed-upon rule on the selection of the appropriate system to be installed at a particular site. This paper has presented multi-objective optimization to select the best operating point of the PAT-SEIG system. The results show that the peak efficiencies for the PAT …

Assessment Of Risk Factors Related To Body Pain Complaints In Tanzania Construction Industry, Fatma K. Mohamed

Tanzania Journal of Engineering and Technology (TJET)

The construction industry is associated with risks that can result in musculoskeletal diseases. Although young male workers who are presumed to be healthy dominate the industry in Tanzania, body pain complaints have been widely reported. The aim of this study is to assess the prevalence and causes of body pains in workers. A cross-sectional study involving 396 workers was conducted. A chi square test was used for testing association of independent categorical variables and binary logistic regression analysis was used to determine predictors for body pain complaints. The results show that all study participants complained of at least one form …

Balsa Bridge, Caleb T. Lovett

All Undergraduate Projects

The problem presented throughout this report was to create a small-scale bridge made entirely out of balsa wood and glue, that could withstand substantial force, as well as perform a lifting/lowering cycle. Other requirements associated with the bridge were properties of weight, deflection, size, and shape. This problem presented a challenge that tested the mathematical side of engineering, being strongly reliant on statics, mechanics of materials, and mechanical design analyses.

To approach this problem, the first step was to complete in depth calculations of the chosen design. With this done, manufacturing and assembly was able to be completed. With a …

Functional Verification Of Additively Manufactured Metallopolymer Structures For Structural Electronics Design, Nathan D. Singhal

Honors Undergraduate Theses

As an attempt to improve the overall cost-effectiveness and ease of structural electronics manufacturing, this study characterizes the mechanical and electrical responses of structures which are fabricated from a novel metallopolymer composite material by fused deposition modeling as they are subjected to quasi-static, uniaxial mechanical tension. Baseline values of tensile properties and electrical resistivity were first obtained via ASTM D638-22 standard testing procedures and linear sweep voltammetry (LSV), respectively. A hybrid procedure to measure in-situ mechanically dependent electrical behavior was subsequently developed and implemented. The mechanical and electromechanical testing was followed by the derivation of stochastic values for several mechanical …

Impact Of Silicon Ion Irradiation On Aluminum Nitride-Transduced Microelectromechanical Resonators, David D. Lynes, Joshua Young, Eric Lang, Hengky Chandrahalim

Faculty Publications

Microelectromechanical systems (MEMS) resonators use is widespread, from electronic filters and oscillators to physical sensors such as accelerometers and gyroscopes. These devices' ubiquity, small size, and low power consumption make them ideal for use in systems such as CubeSats, micro aerial vehicles, autonomous underwater vehicles, and micro-robots operating in radiation environments. Radiation's interaction with materials manifests as atomic displacement and ionization, resulting in mechanical and electronic property changes, photocurrents, and charge buildup. This study examines silicon (Si) ion irradiation's interaction with piezoelectrically transduced MEMS resonators. Furthermore, the effect of adding a dielectric silicon oxide (SiO₂) thin film is …

Mechanical Design Of A Microwave Imaging Device For Breast Cancer Detection In Mri Scanners, Grace M. Player

Dartmouth College Master’s Theses

This project seeks to develop an updated version of a microwave imaging device for use in conjunction with breast MRI, improving upon existing technology and developing novel concepts for the device. It posits three primary redesign targets for updating the previous system: resizing the system height, making the device more iteration- friendly, and improving the overall manufacturability of the device by replacing custom components with commercially available alternatives. All three of these redesign targets are met in the new design, V2.0. The height is reduced by reducing antenna travel and height, embedding some components, and shortening the tank wall, resulting …

An Application Of Optimized Bistable Laminates As A Low Velocity, Low Impact Mechanical Deterrent, Graham Lancaster

All Theses

This research considers the problem of using bistable laminates as a mechanical deterrent to the impending impact of a particle. The structure will be controlled through an algorithm that will utilize piezoelectric devices to activate them in unison with the bistable laminate to successfully deter. A novel experimental setup will be constructed to ensure that the bistable laminate stays fixed when acting as a mechanical deterrent. Piezoelectricity is the main driving force of the bistable laminate to morph and this study will use a Macro Fiber Composite (MFC) actuator that contains piezoelectric ceramic rods in a patch to transfer electrical …

The Design And Manufacturing Of An Environmental Chamber To Test Microelectronic Devices, William Graber, Aniket Roy Chowdhury

The Journal of Purdue Undergraduate Research

No abstract provided.

Machine Learning Approach For Classifying Power Outage In Secondary Electric Distribution Network, Stephan Mgaya, Hellen Maziku

Tanzania Journal of Engineering and Technology (TJET)

Power outage is the problem that hinders social and economic development especially for developing countries like Tanzania. Frequent power outages damage electric equipment, and negatively affect the industrial production process. Power outages cannot be completely eradicated due to uncontrolled cause like natural calamities but technical challenges can be managed and hence reducing power outages. The existing manual methods used to locate power outage like customer calls is inefficient and time consuming. On the other hand, modern method like the Advanced Metering Infrastructure (AMI) still faces a challenge in effectively classifying power line outage due to the nature of imbalanced datasets. …

An Iot Based Worker Safety Helmet Using Cloud Computing Technology, Yuthriya Iddi Khamis, Mahmoud Alawi, Waheed Muhammad Sanya

Tanzania Journal of Engineering and Technology (TJET)

Miner safety and security is a major challenge around the world due to the exposure to toxic gases that are frequently released in underground mines. Miners' health is adversely affected primarily by toxic gases, which endanger the workers' lives. Furthermore, human sensory abilities do not detect these dangerous gases. As a result, this paper proposes a safety monitoring system that includes a temperature sensor, humidity sensor, and gas sensors to detect harmful gases and alert miners to those harmful gases using the smart helmet they wear. These gases are transmitted to the control station via the cloud using Internet of …

Group-Based Data Offloading Techniques Assisted By D2d Communication In 5g Mobile Network, Juma S Ally

Tanzania Journal of Engineering and Technology (TJET)

Machine type communication devices proposed as one of the substantial data collections in the 5G of wireless networks. However, the existing mobile communication network is not designed to handle massive access from the MTC devices instead of human type communication. In this context, we propose the device-to-device communication assisted a mobile terminal (smartphone) on data computing, focusing on data generated from a correlated source of machine type communication devices. We consider the scenario that the MTC devices after collecting the data will transmit to a smartphone for computing. With the limitation of computing resources at the smartphone, some data are …

Assessment Of Energy Efficiency In Beverage Industry, Mahamudu H. Mtebwa

Tanzania Journal of Engineering and Technology (TJET)

The brewery industry has a significant contribution to the national income. However, it is also associated with energy intensive processes and pollution. In this work, the energy efficiency assessment of the largest brewery in Tanzania i.e., Tanzania Breweries Limited has been conducted. Energy consumption analysis was conducted according to IEEE SA 739 1995. Important parameters used to assess brewery energy efficiency were boiler efficiency and losses, equipment energy productivity as well as load factor. It was found that the main energy consumers are packaging (54.63%), brewing (29.30%) and utilities (15.17%). More importantly, it was found that about 68% of the …

A Model For Sustainable Adoption Of Solar Photovoltaic Technology In Tanzania, Joseph Kihedu

Tanzania Journal of Engineering and Technology (TJET)

The aim of the study was to develop a sustainable model for enhancement of the solar PV technology adoption in Tanzania. The model was developed based on the identified barriers that hinder the adoption of solar PV technology and adopted the best strategies from successful projects. Further, the drivers and activities were developed based on selected best strategies from successful projects. The identified barriers to the adoption of solar PV technology, which are grouped into five associated categories and their significances, are lack of access to finance (32%), non-enforcement of policy and regulation (31%), technical (18%), lack of awareness (9%) …

Challenges And Signal Processing Of High Strain Rate Mechanical Testing, Barae Lamdini

Theses and Dissertations

Dynamic testing provides valuable insight into the behavior of materials undergoing fast deformation. During Split-Hopkinson Pressure Bar testing, stress waves are measured using strain gauges as voltage variations that are usually very small. Therefore, an amplifier is required to amplify the data and analyze it. One of the few available amplifiers designed for this purpose is provided by Vishay Micro-Measurements which limits the user’s options when it comes to research or industry. Among the challenges of implementing the Hopkinson technology in the industry are the size and cost of the amplifier. In this work, we propose a novel design of …

Electromechanical Fatigue Properties Of Dielectric Elastomer Stretch Sensors Under Orthopaedic Loading Conditions, Andrea Karen Persons

Theses and Dissertations

Fatigue testing of stretch sensors often focuses on high amplitude, low-cycle fatigue (LCF) behavior; however, when used for orthopaedic, athletic, or ergonomic assessments, stretch sensors are subjected to low amplitude, high-cycle fatigue (HCF) conditions. As an added layer of complexity, the fatigue testing of stretch sensors is not only focused on the life of the material comprising the sensor, but also on the reliability of the signal produced during the extension and relaxation of the sensor. Research into the development of a smart sock that can be used to measure the range of motion (ROM) of the ankle joint during …