Electro-Mechanical Systems Commons^™

Techno-Economic Analysis Of The Utilization Of Waste-To-Energy In Jakarta Industrial Estate Pulogadung, Wahyu Punjung Pesonagrata, Mohammad Akita Indianto

Journal of Materials Exploration and Findings

Indonesia has a serious waste problem, which ranking second in marine pollution. Due to significant environmental impacts, a solution to overcome the complexity of waste problems is needed. This study took sample on waste management in Jakarta Industrial Estate Pulogadung (JIEP). JIEP is an Industrial area which covers 443 hectares of land in East Jakarta. This study aims to address Indonesia's serious waste problem by exploring the potential utilization of waste in the Jakarta Industrial Estate Pulogadung (JIEP) as Refuse-Derived Fuel (RDF) for a waste-to-energy (WtE) power plant. The proposed method used a steam power plant with RDF as fuel …

Me3329 Modular Phonograph Gearbox, Garrett Andrik Leighton, Preston Robert Hupe, Gavin Carter Ebner, Andrew Renato Reyes

Mechanical Engineering

The Mechanical Engineering Department at California Polytechnic State University, San Luis Obispo (Cal Poly), seeks to develop a laboratory tool allowing students to reinforce concepts of gears for Mechanical Systems Design (ME329). Some current laboratories do not provide students with hands-on interaction, and the department lacks equipment and documentation to support a standardized lab. With ME329 expanding from ten to fifteen weeks, there is an opportunity to create a physical gearbox design lab allowing students to reinforce lecture material in engaging ways, while standardizing student learning. This senior project is presented and sponsored by Professor Alan Zhang. It will be …

Effects Of Cutting Conditions On Tool Temperature And Material Removal Rate In Turning Operations, Simon I. Marandu

Tanzania Journal of Engineering and Technology (TJET)

Cutting conditions in manufacturing processes have effects on tool temperature and material removal rate. The objective of this study was to investigate the effects of cutting conditions namely spindle speed, feed rate, depth of cut and tool nose radius on tool temperature and material removal rate in turning operations. A total of 81 experiments were conducted to measure tool temperature and material removal rate in order to determine the effects of cutting conditions on tool temperature and material removal rate using ANOVA and regression analysis. The results show that tool nose radius, depth of cut, and spindle speed are significant …

Cellulose Recovery From Waste Denim Fabrics Through Indigo Vat Dye Reduction And Spandex Dissolution, Tito N. Venance

Tanzania Journal of Engineering and Technology (TJET)

This study addresses environmental conservation by tackling end-of-life management for post-consumer denim garments through the recycling of cotton fibres from waste denim. The purification process involved dithionite reduction of vat dyes in the presence of an alkali followed by selective dissolution of spandex using N,N-dimethylformamide (DMF). Optimal conditions for dye removal were determined at 90°C for 120 minutes with sodium hydroxide at 25 g/L, sodium dithionite at 6 g/L and PVP at 4.5 g/L, while spandex extraction was achieved using a 5% DMF solution at 70°C for 4 hours. Ultraviolet (UV)-vis spectrophotometric analysis indicated a significant increase in whiteness (DL*). …

Application Of Artificial Neural Network Models For Predicting Diesel And Petrol Prices In The Geographically Sparsed Regions In Tanzania, John M. Kafuku

Tanzania Journal of Engineering and Technology (TJET)

Fuel consumption in Tanzania, mainly diesel and petrol, accounts for 82 percent of the energy consumption in the country, with significant price volatility affecting market stability, availability of fuel, and investment decisions. This study uses an artificial neural network (ANN) with a backpropagating algorithm to predict fuel prices in four regions of Tanzania. Key input parameters include the currency inflation rate (CIR), the petrol fuel inventory (PFI), the diesel fuel inventory (DFI), and the fuel transport costs (FTC). The study selected the 6-10-10-2 ANN structures for Sumbawanga-Rukwa, Mpanda-Katavi, and Mbeya-Mbeya as well as 6-10-9-2 for the Songea-Ruvuma region. The results …

Factors Affecting Adoption Of Industry 4.0 Predictive Maintenance By Manufacturing Industries: Tanzania Food And Beverage Manufacturing Industries, Fred E. Peter

Tanzania Journal of Engineering and Technology (TJET)

Industry 4.0 has increasingly become a focal point of scholarly inquiry. Nonetheless, there remains a noticeable lack of comprehensive research on the diverse and systematic factors that influence the adoption of Industry 4.0 Predictive Maintenance (PdM 4.0) in manufacturing sectors within developing regions, particularly in East Africa. This study seeks to bridge this research gap by investigating the key determinants affecting the actual implementation of PdM 4.0 in Tanzania’s food and beverage manufacturing industries. To achieve this objective, a mixed-methods research design was adopted, combining both qualitative and quantitative approaches. Qualitative data were obtained through in-depth interviews with ten industry …

3d Printed Microfluidic Fabrication Methodology, Characterization, Mechanical Design, And Applications In Electrostatic Artificial Muscles And Benthic Microbial Fuel Cells, Terak B. Hornik

Master's Theses

The fabrication of microfluidic devices often requires specialized methods. The development of these methods requires careful characterization and understanding of the processes involved. Using primarily PolyJet 3D printing technology, microfluidics offers a wide scope of applications such as microfluidic benthic microbial fuel cells (MBMFCs) and electrostatic artificial muscles. MBMFCs benefit from the confinement of the microbes resulting in close proximity between the electrode and the organisms. Using a modular design called the Sponge, assembly and upscaling is possible. Electrostatic artificial muscles benefit from a microfluidic approach due to the non-linearity of electrostatic attraction creating disproportionate benefits when miniaturized. When designed …

Capacitive Sensors With Ultra-Small Capacitance For Smart Measurement And Control Systems, Rustam Baratov, Farrux Jabbor O'G'Li Ko'charov

Chemical Technology, Control and Management

This article discusses methods of low capacitance measurement of capacitive sensors. The results of the study of the amplitude-frequency (AF) and phase-frequency (PF) response of measurement circuits of capacitive sensors for low capacitances measurement, consisting of RC - differentiating elements are presented. The input and output parameters of the differentiating circuit and the complex transfer function are analyzed. The research results show that low capacitances measurement by measuring the rectangular pulses duration is the most effective measurement method.

Towing Tank Trials Of Hydrokinetic Turbine Scale Model To Support Marine Energy System Verification, Shahab Rouhi

LSU New Orleans Theses and Dissertations

In response to the escalating demand for sustainable energy solutions and the critical reevaluation of conventional fossil fuels due to environmental concerns, this dissertation embarks on a comprehensive exploration of hydrokinetic energy as a promising alternative. The study delves into the underexplored domain of hydrokinetic energy, leveraging innovative methodologies for effective utilization and harnessing, particularly through the development and investigation of hydrokinetic turbines.

In the realm of hydrokinetic energy conversion, our research has exclusively concentrated on horizontal-axis turbines, distinct from other turbine configurations. Noteworthy is the adaptation of a conventional horizontal-axis wind turbine for water currents, revealing enhanced performance through …

Cal Poly Fluid Power Vehicle Challenge 2024, J. Mason Gray, Ryan D'Amour, Alberto Acho Lopez, Christian Ferrandino, Johnathan Dietz

Mechanical Engineering

In this Final Design Review, the Cal Poly Fluid Power Vehicle Team competed in Norgren’s 2024 Fluid Power Vehicle Challenge. The design need of the competition was for college teams to compete with human-powered, hydraulic-driven vehicles in an endurance race, a sprint race, an efficiency race, and a regenerative power race. The competition need was to design a vehicle to win in as many races as possible, achieving the highest overall score and winning the competition. With a design emphasis on the endurance and sprint race, the Cal Poly team designed a fluid power system that fastened to a purchased …

Balsa Bridge, Caleb T. Lovett

All Undergraduate Projects

The problem presented throughout this report was to create a small-scale bridge made entirely out of balsa wood and glue, that could withstand substantial force, as well as perform a lifting/lowering cycle. Other requirements associated with the bridge were properties of weight, deflection, size, and shape. This problem presented a challenge that tested the mathematical side of engineering, being strongly reliant on statics, mechanics of materials, and mechanical design analyses.

To approach this problem, the first step was to complete in depth calculations of the chosen design. With this done, manufacturing and assembly was able to be completed. With a …

Impact Of Silicon Ion Irradiation On Aluminum Nitride-Transduced Microelectromechanical Resonators, David D. Lynes, Joshua Young, Eric Lang, Hengky Chandrahalim

Faculty Publications

Microelectromechanical systems (MEMS) resonators use is widespread, from electronic filters and oscillators to physical sensors such as accelerometers and gyroscopes. These devices' ubiquity, small size, and low power consumption make them ideal for use in systems such as CubeSats, micro aerial vehicles, autonomous underwater vehicles, and micro-robots operating in radiation environments. Radiation's interaction with materials manifests as atomic displacement and ionization, resulting in mechanical and electronic property changes, photocurrents, and charge buildup. This study examines silicon (Si) ion irradiation's interaction with piezoelectrically transduced MEMS resonators. Furthermore, the effect of adding a dielectric silicon oxide (SiO₂) thin film is …

An Application Of Optimized Bistable Laminates As A Low Velocity, Low Impact Mechanical Deterrent, Graham Lancaster

All Theses

This research considers the problem of using bistable laminates as a mechanical deterrent to the impending impact of a particle. The structure will be controlled through an algorithm that will utilize piezoelectric devices to activate them in unison with the bistable laminate to successfully deter. A novel experimental setup will be constructed to ensure that the bistable laminate stays fixed when acting as a mechanical deterrent. Piezoelectricity is the main driving force of the bistable laminate to morph and this study will use a Macro Fiber Composite (MFC) actuator that contains piezoelectric ceramic rods in a patch to transfer electrical …

Assessment Of Energy Efficiency In Beverage Industry, Mahamudu H. Mtebwa

Tanzania Journal of Engineering and Technology (TJET)

The brewery industry has a significant contribution to the national income. However, it is also associated with energy intensive processes and pollution. In this work, the energy efficiency assessment of the largest brewery in Tanzania i.e., Tanzania Breweries Limited has been conducted. Energy consumption analysis was conducted according to IEEE SA 739 1995. Important parameters used to assess brewery energy efficiency were boiler efficiency and losses, equipment energy productivity as well as load factor. It was found that the main energy consumers are packaging (54.63%), brewing (29.30%) and utilities (15.17%). More importantly, it was found that about 68% of the …

A Model For Sustainable Adoption Of Solar Photovoltaic Technology In Tanzania, Joseph Kihedu

Tanzania Journal of Engineering and Technology (TJET)

The aim of the study was to develop a sustainable model for enhancement of the solar PV technology adoption in Tanzania. The model was developed based on the identified barriers that hinder the adoption of solar PV technology and adopted the best strategies from successful projects. Further, the drivers and activities were developed based on selected best strategies from successful projects. The identified barriers to the adoption of solar PV technology, which are grouped into five associated categories and their significances, are lack of access to finance (32%), non-enforcement of policy and regulation (31%), technical (18%), lack of awareness (9%) …

Electromechanical Fatigue Properties Of Dielectric Elastomer Stretch Sensors Under Orthopaedic Loading Conditions, Andrea Karen Persons

Theses and Dissertations

Fatigue testing of stretch sensors often focuses on high amplitude, low-cycle fatigue (LCF) behavior; however, when used for orthopaedic, athletic, or ergonomic assessments, stretch sensors are subjected to low amplitude, high-cycle fatigue (HCF) conditions. As an added layer of complexity, the fatigue testing of stretch sensors is not only focused on the life of the material comprising the sensor, but also on the reliability of the signal produced during the extension and relaxation of the sensor. Research into the development of a smart sock that can be used to measure the range of motion (ROM) of the ankle joint during …

Schaeffler E-Motor, Jenne Harasin, Zachary Zatta, Christopher Tvaroch

Williams Honors College, Honors Research Projects

This project will be focusing on the work accomplished at Schaeffler to convert an existing internal combustion engine, Ford F-250 truck, into a battery electric vehicle. This report focuses on the vehicle's integration with an emphasis on the bearing design, e-Axle housing's method for mounting, bus bar design, resolver design, differential options, wiring for low and high voltage, and oil pump and cooling system for e-Beam. The bearings for the differential as well as the power transmission system from the electric motor to the e-Axle will need to be specified. By late summer 2022, Schaeffler will have a working prototype …

Performance Of Calcium Chloride- Ammonia Adsorption Refrigeration System, Michael John

Tanzania Journal of Engineering and Technology (TJET)

An experimental study on the performance of calcium chloride-ammonia adsorption system is described. A single bed water cooled condenser adsorption refrigerator prototype, which utilises calcium chloride-ammonia pair has been developed and tested in the laboratory. Experiments have been conducted for desorption temperatures of 100 °C with desorption time varying from 1 to 4 hours. An electric tape heater and a timer were used to perform the experiments. The adsorption temperature profile, adsorption rate and prototype performance have been analysed and discussed. The tested heating and desorption temperature of 100 °C and heating and desorption time of 1 to 4 hours …

Assessment Of The Impacts Of Climate Variability On Hydropower Generation: A Case Study Of The New Pangani Falls, Tanzania, Dativa Byarufu

Tanzania Journal of Engineering and Technology (TJET)

Climate change poses potential impacts on hydropower generation either positively by increasing or negatively by decreasing river flow. This study assessed the impacts of climate variability on hydropower with a focus on the New Pangani Falls in Tanzania. Rainfall and temperature time series data from 1980-2014 were analyzed in relation to river discharge and associated impacts to hydropower generation. The Man-Kendall test was used to detect trend in both annual and seasonal time series. The results showed a negative trend in annual rainfall with Z= -2.41 at α = 0.05 and the slope Q = -0.964. Seasonal trend analysis showed …

Development Of Novel Battery Materials For Lithium-Ion Batteries And Beyond, Jiyu Cai

Graduate Theses and Dissertations

As fossil fuels are depleting and causing environmental issues, it becomes imperative to widely implement renewable energies (e.g., solar and wind power). In this context, electrical energy storage (EES) systems are essential to accommodate the intermittent supply and uneven distribution of renewable energies. To this end, high-energy-density EES devices are highly demanded, such as rechargeable batteries. This dissertation presents my efforts in developing novel battery materials for lithium-ion batteries (LIBs), sodium-ion batteries (SIBs), and solidstate lithium batteries (SSLBs). These efforts include electrochemical evaluations of battery materials, surface modifications of electrodes via atomic layer deposition (ALD), and advanced characterizations of batteries …

Mini Rc Baja Car, Jason Schindler

All Undergraduate Projects

Incorporating each aspect of engineering incorporated into a senior project is difficult. That is why an RC Baja car is a great senior project for Mechanical Engineering students. The approach that students must take to design, construct, and test the car is to set parameters, and to make overall goals that can be easily measured. These goals include, but not limited to things like a $700 budget and the ability to withstand a 1-foot drop to a flat surface on all four wheels simultaneously. First, the design must meet the specifications and rules that are set previously. This ensures that …

Stability Analysis, Dynamic Modeling, And Kinematic Analysis Of Hydraulically Amplified Dielectric Elastomer Actuators And Robot Manipulators, Amir Hosein Zamanian

Mechanical Engineering Research Theses and Dissertations

In this dissertation, we have proposed a new dielectric elastomer actuator design and model that couples electrostatics, fluid mechanics, linear and nonlinear elastic deformations. The internal hydraulic pressure can amplify the structural deformation generated by induced electrostatic forces (Maxwell pressure), given the name of this class of actuators, hydraulically amplified dielectric elastomer actuators (HADEAs).

First, we developed novel lumped-parameter models (LPMs) using linear and hyper-elastic material models and second compared the LPM results with finite element analysis in quasi-static simulations. We analytically expressed the conditions for the snap-through instability in the HADEA, which appears after exceeding a certain voltage applied …

Dual-Axis Solar Tracker, Bryan Kennedy

All Undergraduate Projects

Renewable energies, and fuels that are not fossil fuel-based, are one of the prolific topics of debate in modern society. With climate change now becoming a primary focus for scientists and innovators of today, one of the areas for the largest amount of potential and growth is that of the capturing and utilization of Solar Energy. This method involves using a mechanical system to track the progression of the sun as it traverses the sky throughout the day. A dual-axis solar tracker such as the one designed and built for this project, can follow the sun both azimuthally and in …

Automated Runout Measurement Tool, Ethan Tisch

Williams Honors College, Honors Research Projects

A new measurement process and tool is to be developed to improve the existing method for measuring runout on the commutators of brushed DC product.

After an armature is manufactured, the commutator is inspected by placing the completed rotor assembly in one of several non-standard measurement fixtures. An indicator is then positioned on the commutator. A trained operator proceeds to rotate the armature while taking runout and bar-to-bar measurement at various positions along the length of the commutator.

This existing process is slow, costly, and unreliable. For these reasons, there is substantial economic pressure to develop a superior method for …

The Potentials Of Faecal Sludge Treatment Using Local Conditioners In Tanzania: A Review, Doglas Benjamin1

Tanzania Journal of Engineering and Technology (TJET)

Worldwide, every day human beings generate millions of tons of Faecal Sludge (FS), which is rich in water, nutrients, energy, and organic compounds. Yet FS is not being managed in a way that permits us to derive value from its reuse, while at the same time, millions of farmers struggle with depleted soils and lack of water. In most of the developing countries, energy for cooking is mainly derived from cutting of trees, either as wood or charcoal. Resource recovery and reuse from FS can create livelihoods, enhance food security, support green economies, reduce waste and contribute to cost recovery …

Comparative Study Of Power Semiconductor Devices In A Multilevel Cascaded H-Bridge Inverter, Kenneth Mordi

Graduate Theses and Dissertations

This thesis compares the performance of a nine-level transformerless cascaded H-bridge (CHB) inverter with integrated battery energy storage system (BESS) using SiC power MOSFETs and Si IGBTs. Two crucial performance drivers for inverter applications are power loss and efficiency. Both of these are investigated in this thesis. Power devices with similar voltage and current ratings are used in the same inverter topology, and the performance of each device is analyzed with respect to switching frequency and operating temperature. The loss measurements and characteristics within the inverter are discussed. The Saber® simulation software was used for the comparisons. The power MOSFET …

Formation Of Mound-Like Multiscale Surface Structures On Titanium By Femtosecond Laser Processing, Edwin Peng, Alfred Tsubaki, Craig A. Zuhlke, Ryan Bell, Meiyu Wang, Dennis R. Alexander, George Gogos, Jeffrey E. Shield

Department of Mechanical and Materials Engineering: Dissertations, Theses, and Student Research

Surface Functionalization Technique • Femtosecond Laser Surface Processing (FLSP) • Utilize high power, femtosecond (10-15 s) laser pulses • Produce self-organized, multiscale surface micro/nanostructures • Diverse range of applicable substrates: semiconductors, metals, polymers, & composites

Why? • What are the different types of FLSP structures on Ti? • Physical evidence needed for FLSP formation models • Optimize FLSP of Ti for biomedical & other applications

How? • Obtain evidence of mound growth processes by examining underlying microstructure • Utilize dual beam Scanning Electron Microscope-Focused Ion Beam instrument to cross section surface structures & fabricate transmission electron microscopy samples

Electromechanics Of An Ocean Current Turbine, Vasileios Tzelepis

LSU New Orleans Theses and Dissertations

The development of a numeric simulation for predicting the performance of an Ocean Current Energy Conversion System is presented in this thesis along with a control system development using a PID controller for the achievement of specified rotational velocity set-points. In the beginning, this numeric model is implemented in MATLAB/Simulink® and it is used to predict the performance of a three phase squirrel single-cage type induction motor/generator in two different cases. The first case is a small 3 meter rotor diameter, 20 kW ocean current turbine with fixed pitch blades, and the second case a 20 …

Vibration-Based Health Monitoring Of Multiple-Stage Gear Train And Differential Planetary Transmission Involving Teeth Damage And Backlash Nonlinearity, Andrew Patrick Sommer

Master's Theses

The objective of this thesis is to develop vibration-based fault detection strategies for on-line condition monitoring of gear transmission systems. The study divides the thesis into three sections. First of all, the local stresses created by a root fatigue crack on a pinion spur gear are analyzed using a quasi-static finite element model and non-linear contact mechanics simulation. Backlash between gear teeth which is essential to provide better lubrication on tooth surfaces and to eliminate interference is included as a defect and a necessary part of transmission design. The second section is dedicated to fixed axis power trains. Torsional vibration …

Socio-Economic Impacts Of Computer Viruses In Tanzania, M Victor

Tanzania Journal of Engineering and Technology (TJET)

This paper reports on a research project conducted with an objective of identifying and assessing various approaches used by different computer users (Management, System Administrators and end users) in Tanzania to combat computer viruses (CVs), and to assess users' awareness level on CVs. Specifically, the study aimed at assessing the awareness level on CVs to the Tanzanian business community; analyze the socio -economic impact caused by CVs in Tanzania and; assess existing methods, capacity and limitations on controlling CVs in Tanzania. Data was collected using both questionnaires and interview from financial institutions such as NBC and BOT, and telecommunications sector …