Computer-Aided Engineering and Design Commons^™

H.F. Hauff Outrigger: Vertical Arm, Juan Tovar

All Undergraduate Projects

H.F. Hauff is a company based out of Yakima which specializes in farming equipment. One of their products is a trailer which has a wind machine attached to it. In order to keep the fan’s thrust from tipping the trailer over, the trailer needs outriggers to extend out. The outriggers also serve as a way to level out the trailer in uneven surfaces. The outriggers are what needed to be designed. This portion of the project was the vertical arm which extends from the horizontal arm, and goes towards the ground to raise the trailer. The project consisted of three …

Chocolate Bar Wrapping Machine, Austin M. Hoff, Daniel R. Trepke, Caleb B. Krichbuam

Williams Honors College, Honors Research Projects

Gilbert Chocolates has proposed to manufacture a machine to wrap chocolate bars. This machine is intended to replace two people wrapping the chocolate bars by hand, which is a time consuming method. This is especially apparent between October and January when the workers are working long hours in preparation for the Christmas rush of customers. Currently wrapping a bar takes about a minute and Gilbert Chocolates wants this time reduced down to 20-30 seconds. The budget for this project is set at $1000, and is being funded by the company. This machine needs to fit in a cubic foot of …

Selective Resistive Sintering: A Novel Additive Manufacturing Process, Austin Bryan Van Horn

Graduate Theses and Dissertations

Selective laser sintering (SLS) is one of the most popular 3D printing methods that uses a laser to pattern energy and selectively sinter powder particles to build 3D geometries. However, this printing method is plagued by slow printing speeds, high power consumption, difficulty to scale, and high overhead expense. In this research, a new 3D printing method is proposed to overcome these limitations of SLS. Instead of using a laser to pattern energy, this new method, termed selective resistive sintering (SRS), uses an array of microheaters to pattern heat for selectively sintering materials. Using microheaters offers significant power savings, significantly …

Solar Car Suspension System, Alex Power, Adam O'Camb

Mechanical Engineering

No abstract provided.

Novel Closed-Loop Control Strategy For Inkjet-Based Additive Manufacturing System, Yunong Shi, Chunsheng Ye

The 8th International Conference on Physical and Numerical Simulation of Materials Processing

No abstract provided.

Simulation Of Superplastic Forming Of Circular Edge-Welded Envelopes, Olga Tulupova

The 8th International Conference on Physical and Numerical Simulation of Materials Processing

No abstract provided.

Simulation Investigation Of Temperature Distribution In Large Aluminium Panel During Autoclave Age Forming Process, Yongqian Xu

The 8th International Conference on Physical and Numerical Simulation of Materials Processing

No abstract provided.

Simulation Of Two Kinds Of Hot Stamping Processes Of Ultra High-Strength Steel, Hao Zhao, Zhongwen Xing, Hongliang Yang

The 8th International Conference on Physical and Numerical Simulation of Materials Processing

No abstract provided.

Fatigue Analysis Of The Welded Region In The Automotive Torsion Beam Rear Suspension System, Nan Zhan, Xiaochuan Zhang

The 8th International Conference on Physical and Numerical Simulation of Materials Processing

No abstract provided.

Process Optimization Of Water Chamber Based On Numerical Simulation, Yang Jian Ning, Yang Yi, Yang Gang

The 8th International Conference on Physical and Numerical Simulation of Materials Processing

No abstract provided.

Temperature Filed Numerical Simulation Of Laser Welding For Ta15 Titanium Alloy By Coupling Thermal And Phase Transformation, Wenmin Ou, Yanhong Wei, Xiaohong Zhan, Gaoyang Mi

The 8th International Conference on Physical and Numerical Simulation of Materials Processing

No abstract provided.

Numerical Simulation Of Material Flow During Fsw To Predict Defect Generation Based On Non-Uniform Tool–Material Contact Condition, Yu-Can Zhu, Gao-Qiang Chen, Shuai Zhang, Qi-Long Cheng, Qi-Long Cheng, Gong Zhang, Qing-Yu Shi

The 8th International Conference on Physical and Numerical Simulation of Materials Processing

No abstract provided.

Modeling And Simulation Of Dendrite And Porosity Evolution During Solidification In The Molten Pool Of Al–Cu Alloys, Cheng Gu, Yanhong Wei, Xiaohong Zhan

The 8th International Conference on Physical and Numerical Simulation of Materials Processing

No abstract provided.

Design And Validation Of Parametric Modelling Platform Based On Abaqus, Weiwei Wang, Binbin Jia, Nan Zheng, Chen Zhao

The 8th International Conference on Physical and Numerical Simulation of Materials Processing

No abstract provided.

Calphad-Based Materials Genome And Its Applications To Additive Manufacturing, Wei Xiong

The 8th International Conference on Physical and Numerical Simulation of Materials Processing

No abstract provided.

Fine Element Simulation Of A Modified Fine-Blanking Process To Eliminate The Die-Roll Size, Lin Hua, Bo Tang, Yanxiong Liu, Huajie Mao

The 8th International Conference on Physical and Numerical Simulation of Materials Processing

No abstract provided.

Determining The Print Accuracy Of Four Three-Dimensional Printers, Kshiteej Dalal

Master of Technology Management Plan II Graduate Projects

Rapid prototyping [RP] or 3D printing [3DP] have existed for some time now. One of the major deficiencies of 3DP is the accuracy of the printed three dimensional parts. Even beyond that is the lack of studies that have been designed to measure the 3DP components. Measuring, verifying and determining the accuracy of 3DP parts is the focus of this study. As the accuracy is measured and approaches those of CNC machined parts, it will drive the development of additional additive manufacturing [AM] machinery. In this project a component is created in a solid modeling package. A solid model of …

El Capitán: Cal Poly Rose Float Digital Drive System, Gregory Raffi Baghdikian

Computer Engineering

In today’s world of smartphones, self-driving cars, and internet-connected coffee makers, it seems as if computers are contained in everything around us. These “embedded systems” have become critical components of our lives, improving everything about the things they control, from cost, to speed, to simplicity. One area that embedded systems has hardly gained a foothold is in the world of floatbuilding. Most of the floats in the Tournament of Roses Parade, including the one built jointly by Cal Poly San Luis Obispo and Cal Poly Pomona, are technologically very simple, using mostly analog components and rudimentary discrete digital logic to …

Universal Weight Machine, Oscar Andrade, Bibiana Koch, Robert Molloy, Haley Rentfro, Emily Woods

Mechanical Engineering

The purpose of this project is to design and build an inexpensive, universally accessible multi-station exercise machine for the physical and mental well-being of athletes of the Special Olympics and Pathpoint Life Education & Advancement Program. The machine has three sides tiered to higher resistance: the first station offers a minimal resistance aerobic exercise focused on moving the arms with an ergometer, the second station provides numerous locations to latch on resistance bands that will build strength in the athlete’s arms and chest, and the final station has a donated weight machine that offers lat pulldowns and flys with maximum …

Automated Bearing Press, David Baker, David Brock, Engelbert Diec

Mechanical Engineering

Our group was presented with a challenge to design an automated machine to replace Micro-Vu’s current manual pressing operation. We moved, planned, and scheduled our tasks for the three quarters we will be working on this project by using a Gantt chart. In designing the machine, we generated concepts and used analysis and prototyping to select the most promising ones. Our final design uses a pneumatic press to press the parts, and it includes magazines to hold the parts before pressing, pneumatic actuators to move the parts to and from the pressing location, and a lever to separate the defective …

4th And 5th Axis Rotary Table, Dakota Bass, Ricky Riedl, Nicole Slagle, Irene Yee

Mechanical Engineering

No abstract provided.

Metals Am Design For Manufacturing, Maren Cosens, Ben Wong, Kevin Hale

Mechanical Engineering

We are looking to improve upon the current post processing techniques for metal additive manufacturing (AM). This project, sponsored by Lawrence Livermore National Laboratory (LLNL), will investigate ways to improve the design of stainless steel 316 parts made by AM, and how these designs will help with post processing techniques. We hope that the findings regarding stainless steel will apply to to improve the AM and post processing handshake in general. In particular, the project will focus on including different features in different basic part design shapes to aid in fixturing and post-processing of the part made by AM. This …

Design And Testing Of A Top Mask Projection Ceramic Stereolithography System For Ceramic Part Manufacturing, Dylan Robert De Caussin

Master's Theses

Ceramic manufacturing is an expensive process with long lead times between

the initial design and final manufactured part. This limits the use of ceramic as a viable material unless there is a large project budget or high production volume associated with the part. Ceramic stereolithography is an alternative to producing low cost parts through the mixing of a photo curable resin and ceramic particles. This is an additive manufacturing process in which each layer is built upon the previous to produce a green body that can be sintered for a fully dense ceramic part.

This thesis introduces a new approach …

Grant County Public Utilities District - Rotor Pole Lifting Device, Baylie Johnson

All Undergraduate Projects

Grant County Public Utilities District is planning a rehabilitation of all turbine and generator units at Priest Rapids Dam beginning in August 2016. After the generator rotor is removed from the unit, the rotor poles must be removed from the rotor. They are oriented vertically in the rotor and horizontally on the floor and in shipping containers. The objective of this project is to design, manufacture and test a lifting and a turning device for Priest Rapids Dam’s generator rotor poles. The lifting device was designed to attach a 3500 pound rotor pole to a crane and lift it. The …

Multiple Apple Box Lift 1/10th Scale Model, Kyle J. Burlingame

All Undergraduate Projects

Title and Author: 1/10th Scale Multiple Apple Box Lift by Kyle Burlingame (Engineering Technologies, Safety, and Construction) Abstract/Artist statement: A 1/10th scale Multiple Apple Box Lift was designed and built as a proof of concept for a full scale device. The Multiple Apple Box Lift was designed to meet a customer’s requirements and to be presented at SOURCE. This device lifts the top half of the stacked apple boxes on a pallet in order to allow access to the boxes in the middle of the stack. The device can be manually operated by two people while in-between narrow rows of …

The Pneumatic Leg Extension, David G. Sedano

All Undergraduate Projects

In recent years, reaching altitudes that are higher than your normal-height has evolved from pure amusement to an “in-demand” necessity out in the field. Means of achieving greater than normal height range from wooden poles to aluminum stilts. The era of ladders and other extension methods are slowly fading away. There are many designs in the market that focus on different factors to make a stilt. As other designs focus on one or two enhancements, the pneumatic leg extension’s objective is to improve all aspects of the stilt. This radical new design differs greatly from traditional stilt designs. The pneumatic …

Conversion Casting: Adapter Hub, Joseph M. Coup

All Undergraduate Projects

The concept of conversion casting makes manufacturing major components much more efficient with regards to time and cost. The conversion cast of the adapter hub used in the Victair Mistifier is a major component that requires 8 hours to machine. The existing hub starts from steel stock and then that block of steel is placed into a CNC machine and coded in to create the adapter hub. The manufacturing method changes to a casting for the adapter hub will create a replicated part that requires 1.5 hours of post machining. The intricate design makes a conversion to casting more effective …

Asme Mini Rc Baja: Drivetrain, Jason M. Moore

All Undergraduate Projects

Title and author: ASME mini RC Baja Drivetrain by Jason Moore; partner Mike Cox. (Engineering Technologies, Safety, and Construction)

Abstract/Artists Statement: The issue that this project is concerned with is how to design and build a drivetrain, steering and suspension systems for an RC car. The systems must be simple and functional. Furthermore, these systems will be designed to fit on a small chassis and not interfere with each other. They also need to be strong and durable enough to propel the car forward and maneuver through various obstacles and be built in a way that is easy to take …

Shellfish Bag Maker, Trevor R. Reher

All Undergraduate Projects

When commercially harvesting shellfish specifically clams and oyster, plastic mesh bags are commonly used to place shellfish in after harvesting on beaches. The issues is taking the raw bag material used for harvest and cutting it to a specified length. The material comes on a 2000 ft. spool and needs to be cut to a length of 54 in. Using an existing but out dated machine, a bench mark was made that the new design must be 10% more efficient for the customer to invest money into building the machine. Using mechanical machine design and computer designing software the machine …

Flag Raising Device, Josh Quintero

All Undergraduate Projects

The motivation for this project stems from a lifetime of boating with father Richard Jones. One problem that many people encounter, including Richard, was when towing someone behind a boat, is the difficulty with handling the warning flag. This flag is used to show other surrounding boats that someone has fallen into the water behind their boat. This warns other boats to stay far away from that area to keep safe from running over the swimmer. Although, when holding the flag in the boat, it can be hard to see at times. The boat driver, or other people standing in …