Biomechanical Engineering Commons^™

How Infant Positioning Impacts Hip Motion And The Associated Implications For Babies With Hip Dysplasia, Lauren Buchele

Biomedical Engineering Undergraduate Honors Theses

Developmental dysplasia of the hip (DDH) refers to a group of disorders, ranging from slight instability (Grades 1-3) to a severe dislocation (Grade 4) of the femoral head from the acetabulum [1]. In order to treat DDH in infants, a reduction procedure and the use of a lower body harness to secure the hip joint as the bones and ligaments re-form properly is typically prescribed. The Pavlik Harness is currently the “gold-standard” orthopedic device used to place hips in proper positioning. However, little research has been reported on the biomechanical affects during use of these device types.

Although the Pavlik …

Analyzing Moment Arm Profiles In A Full-Muscle Rat Hindlimb Model, Fletcher Young, Christian Rode, Alexander Hunt, Roger Quinn

Mechanical and Materials Engineering Faculty Publications and Presentations

Understanding the kinematics of a hindlimb model is a fundamental aspect of modeling coordinated locomotion. This work describes the development process of a rat hindlimb model that contains a complete muscular system and incorporates physiological walking data to examine realistic muscle movements during a step cycle. Moment arm profiles for selected muscles are analyzed and presented as the first steps to calculating torque generation at hindlimb joints. A technique for calculating muscle moment arms from muscle attachment points in a three-dimensional (3D) space has been established. This model accounts for the configuration of adjacent joints, a critical aspect of biarticular …

Hip And Knee Biomechanics For Transtibial Amputees In Gait, Cycling, And Elliptical Training, Greg Orekhov

Master's Theses

Transtibial amputees are at increased risk of contralateral hip and knee joint osteoarthritis, likely due to abnormal biomechanics. Biomechanical challenges exist for transtibial amputees in gait and cycling; particularly, asymmetry in ground/pedal reaction forces and joint kinetics is well documented and state-of-the-art passive and powered prostheses do not fully restore natural biomechanics. Elliptical training has not been studied as a potential exercise for rehabilitation, nor have any studies been published that compare joint kinematics and kinetics and ground/pedal reaction forces for the same group of transtibial amputees in gait, cycling, and elliptical training. The hypothesis was that hip and knee …

Subject-Specific Finite Element Predictions Of Knee Cartilage Pressure And Investigation Of Cartilage Material Models, Michael G. Rumery

Master's Theses

An estimated 27 million Americans suffer from osteoarthritis (OA). Symptomatic OA is often treated with total knee replacement, a procedure which is expected to increase in number by 673% from 2005 to 2030, and costs to perform total knee replacement surgeries exceeded $11 billion in 2005. Subject-specific modeling and finite element (FE) predictions are state-of-the-art computational methods for anatomically accurate predictions of joint tissue loads in surgical-planning and rehabilitation. Knee joint FE models have been used to predict in-vivo joint kinematics, loads, stresses and strains, and joint contact area and pressure. Abnormal cartilage contact pressure is considered a risk factor …

Knee Angles And Axes Crosstalk Correction In Gait, Cycling, And Elliptical Training Exercises, Jordan M. Skaro

Master's Theses

When conducting motion analysis using 3-dimensional motion capture technology, errors in marker placement on the knee results in a widely observed phenomenon known as “crosstalk” [1-18] in calculated knee joint angles (i.e., flexion-extension (FE), adduction-abduction (AA), internal-external rotation (IE)). Principal Component Analysis (PCA) has recently been proposed as a post hoc method to reduce crosstalk errors and operates by minimizing the correlation between the knee angles [1, 2]. However, recent studies that have used PCA have neither considered exercises, such as cycling (C) and elliptical training (E), other than gait (G) nor estimated the corrected knee axes following PCA correction. …

Design And Analysis Of A 3d-Printed, Thermoplastic Elastomer (Tpe) Spring Element For Use In Corrective Hand Orthotics, Kevin Thomas Richardson

Theses and Dissertations--Mechanical and Aerospace Engineering

This thesis proposes an algorithm that determine the geometry of 3D-printed, custom-designed spring element bands made of thermoplastic elastomer (TPE) for use in a wearable orthotic device to aid in the physical therapy of a human hand exhibiting spasticity after stroke. Each finger of the hand is modeled as a mechanical system consisting of a triple-rod pendulum with nonlinear stiffness at each joint and forces applied at the attachment point of each flexor muscle. The system is assumed quasi-static, which leads to a torque balance between the flexor tendons in the hand, joint stiffness and the design force applied to …

Biomechanical Testing Of An Exercise For Strengthening The Proximal Femur., Alyssa Osbourne

Electronic Theses and Dissertations

Based on the principles of cutting edge bone remodeling research, a unique therapeutic exercise device was designed specifically to improve bone quality at the most critical location of the proximal femur prone to fracture: the superior-lateral femoral neck where the fracture first initiates during a fall. The exercise/device is intended to work by inducing enough strain in the bone to stimulate the body’s natural bone remodeling mechanisms to increase bone density in the proximal femur and consequently prevent a fracture from arising if a fall to the side does occur.

In order to test the proposed exercise, experiments simulating the …

Kinematics Of The Lower Extremities During Fundamental Martial Arts Tricking Techniques, Kevin P. Grassie

Honors Scholar Theses

Martial Arts Tricking (MAT) is a relatively new sport that combines martial arts, gymnastics, acrobatics, and breakdancing for the purposes of creating aesthetic and impressive combinations of kicks, flips and twists. It has been growing exponentially through social media and the overall athletic and entertainment communities. The sport is very unique in that the movements, with their blended influences, provide novel ways for athletes to generate and utilize their momentum in a creative way. The results often include off-axis flips and twists, single-leg landings, and complicated yet fluid techniques that easily chain together.

Due to the sport only being a …

Piv Analysis Of Wake Structure Of Real Elephant Seal Whiskers, Joseph Antun Bunjevac

ETD Archive

Seals are able to accurately detect minute disturbances in the ambient flow
environment using their whiskers, which is attributed to the exceptional capability of
their whiskers to suppress vortex-induced vibrations in the wake. To explore potential applications for designing smart flow devices, such as high-sensitivity underwater
flow sensors and drag reduction components, researchers have studied how the role
of some key parameters of whisker-like morphology affect the wake structure. Due to
the naturally presented variation in size and curvature along the length of whiskers,
it is not well understood how a real whisker changes the surrounding flow and the
vortex …

Design And Control Of A Powered Rowing Machine With Programmable Impedance, Jose Humberto De La Casas Zolezzi

ETD Archive

Due to the rise of obesity, diabetes and cardiovascular disease, research in human performance and physical activity has received increased attention. Rowing machines are used for performance improvements through concentric exercises, however a combination of concentric and eccentric actions is known to improve the effectiveness of training. In this work, a conventional rowing machine was modified to include an electric motor and a robust impedance control system, enabling programmable impedance with concentric and eccentric capabilities. Eccentric exercises are known to contribute significantly to the efficacy of training and to diminish the detrimental effects of humans operating in microgravity for long …

The Effects Of Obesity On Resultant Knee Joint Loads For Gait And Cycling, Juan Gutierrez-Franco

Master's Theses

Osteoarthritis (OA) is a degenerative disease of cartilage and bone tissue and the most common form of arthritis, accounting for US$ 10.5 billion in hospital charges in 2006. Obesity (OB) has been linked to increased risk of developing knee OA due to increased knee joint loads and varus-valgus misalignment. Walking is recommended as a weight-loss activity but it may increase risk of knee OA as OB gait increases knee loads. Cycling has been proposed as an alternative weight-loss measure, however, lack of studies comparing normal weight (NW) and OB subjects in cycling and gait hinder identification of exercises that may …

Walking Simulator Mechanism, Titus Lungu, Igor Tachynskyy, Omri Tayyara

The Downtown Review: An Interdisciplinary Journal Written and Peer-Reviewed by Mandel Honors College Students at Cleveland State University

This paper presents the design, simulation, and kinematic evaluation of a mechanism aimed at simulating both the motion and ground reaction forces produced by a human foot while walking. Such a mechanism can be used to test the durability of shoes through life cycle analysis. In attempting to mimic the physical motion of the human foot as closely as possible, the forces experienced by the human foot were also accurately replicated through the incorporation of a non-stationary testing platform. As is shown in the paper, this testing environment allows for simple adjustments to be made in order to simulate different …

Biomechanical Investigation Of Elite Place-Kicking, Chase M. Pfeifer

Department of Mechanical and Materials Engineering: Dissertations, Theses, and Student Research

Many studies aim to understand the fundamentals of kicking commonly displayed by soccer players [4,6,10,16,17,18,24,25,28,29,30,34,36,38,40]. Of those studies, most are limited to a two-dimensional (2D) analysis using high-speed cameras for position tracking or utilizing electromyography to observe the activity of select muscles [4,6,18,25,29,36]. The few studies that investigate kicking using a three-dimensional (3D) model are limited in their position tracking capabilities and focus mainly on joint flexion potentials and foot speed.

This dissertation is a comprehensive biomechanical analysis (kinematic and EMG) of the field-goal place-kicking techniques of four elite kickers in American football. Data were compared and contrasted with ball …

Cell-Matrix Interactions During En Masse Cell Migration, Meng Zhuang, Altug Ozcelikkale, Bumsoo Han

The Summer Undergraduate Research Fellowship (SURF) Symposium

Extended wound care, including prolonged treatment of burn injuries, acute and chronic wounds, is a significant source of patient discomfort and financial burden to public healthcare programs. Both accelerated healing and prevention of scar formation are highly desired but remain to be challenging to achieve. This is primary due to limited understanding of interactions between cells and the surrounding extracellular matrix (ECM) during wound healing. Particularly, collective migration of fibroblasts through provisional matrix, so called en masse migration, is one of these interactions that play a critical role in later stages of granulation tissue formation and wound closure. In addition …

Implementation Of Analytical Fatigue Models Into Opensim To Predict The Effects Of Fatigue On Anterior Cruciate Ligament Loading, Michael A. Samann

Mechanical & Aerospace Engineering Theses & Dissertations

The anterior cruciate ligament (ACL) provides stability to the knee joint while performing activities such as a side step cut. Neuromuscular fatigue, a reduction in muscle force producing capabilities, alters lower extremity mechanics while performing a side step cut and may increase the risk of ACL injury, particularly in females. Musculoskeletal modeling allows for the measurement of muscle forces, which are difficult to measure in-vivo. Therefore, musculoskeletal modeling, may improve our understanding of the effects of neuromuscular fatigue on muscle force production and loading of the ACL. Therefore, the purpose of this study was to develop a musculoskeletal model which …

Analysis And Modeling Of The Roles Of Actin-Myosin Interactions In Bladder Smooth Muscle Biomechanics, Seyed Omid Komariza

Theses and Dissertations

Muscle mechanical behavior potentially plays an important role in some of the most common bladder disorders. These include overactive bladder, which can involve involuntary contractions during bladder filling, and impaired contractility or underactive bladder, which may involve weak or incomplete contractions during voiding. Actin-myosin cross-bridges in detrusor smooth muscle (DSM) are responsible for contracting and emptying the bladder. The total tension produced by muscle is the sum of its preload and active tensions. Studies suggest that actin-myosin cross-links are involved in adjustable preload stiffness (APS), which is characterized by a preload tension curve that can be shifted along the length …

Development And Validation Of A Human Knee Joint Finite Element Model For Tissue Stress And Strain Predictions During Exercise, Spencer D. Wangerin

Master's Theses

Osteoarthritis (OA) is a degenerative condition of cartilage and is the leading cost of disability in the United States. Motion analysis experiments in combination with knee-joint finite element (FE) analysis may be used to identify exercises that maintain knee-joint osteochondral (OC) loading at safe levels for patients at high-risk for knee OA, individuals with modest OC defects, or patients rehabilitating after surgical interventions. Therefore, a detailed total knee-joint FE model was developed by modifying open-source knee-joint geometries in order to predict OC tissue stress and strain during the stance phase of gait. The model was partially validated for predicting the …

Research And Development Of An Extremely Affordable Prosthetic Knee, Victor H. Duenas, Noe Vargas-Hernandez

COURI Symposium Abstracts, Summer 2012

The objective of this research and development work is to apply the design process in a prosthetic knee mechanism. The importance of human knee is founded in the provided mobility, body positioning and support of the body weight. But for amputees, limitations for everyday tasks imply a real challenge. The project scope a cycle involving the social need, the development and the supply of the solution layout. The motivation is to improve life quality through voluntary and independent human movement by providing a low cost knee design.

The design process requires the conceptual, embodiment, detail and evaluation phases to complete …

Implicit Methods For Efficient Musculoskeletal Simulation And Optimal Control, Antonie J. Van Den Bogert, Dimitra Blana, Dieter Heinrich

Mechanical Engineering Faculty Publications

The ordinary differential equations for musculoskeletal dynamics are often numerically stiff and highly nonlinear. Consequently, simulations require small time steps, and optimal control problems are slow to solve and have poor convergence. In this paper, we present an implicit formulation of musculoskeletal dynamics, which leads to new numerical methods for simulation and optimal control, with the expectation that we can mitigate some of these problems. A first order Rosenbrock method was developed for solving forward dynamic problems using the implicit formulation. It was used to perform real-time dynamic simulation of a complex shoulder arm system with extreme dynamic stiffness. Simulations …

A Biomechanical Comparison Of Polymethylmethacrylate-Reinforced And Expansive Pedicle Screws In Pedicle-Screw Revisions, Bora Bostan, Irfan Esenkaya, Taner Gunes, Mehmet Erdem, Murat Asci, Mehmet Halidun Kelestemur, Cengiz Sen

Faculty Publications - Mechanical Engineering

Objectives: Different techniques and choices exist for revision of pedicle screws, two of which are pedicle screw combined with cement augmentation and expansive pedicle screw fixation. This biomechanical study was designed to compare the pullout strengths of two different revision techniques. Methods: Fourteen lumbar vertebrae obtained from four calves (mean age 15 months) were divided into two groups equal in number. Monoaxial 6.0-mm pedicle screws were inserted into the right pedicles, and axial pullout testing was performed at a rate of 10 mm/min and failure strengths were recorded. Revision was performed with the same-sized pedicle screws reinforced with polymethyl-methacrylate in …

A Real-Time, 3-D Musculoskeletal Model For Dynamic Simulation Of Arm Movements, Edward K. Chadwick, Dimitra Blana, Antonie J. Van Den Bogert, Robert F. Kirsch

Mechanical Engineering Faculty Publications

Neuroprostheses can be used to restore movement of the upper limb in individuals with high-level spinal cord injury. Development and evaluation of command and control schemes for such devices typically require real-time, ldquopatient-in-the-looprdquo experimentation. A real-time, 3-D, musculoskeletal model of the upper limb has been developed for use in a simulation environment to allow such testing to be carried out noninvasively. The model provides real-time feedback of human arm dynamics that can be displayed to the user in a virtual reality environment. The model has a 3-DOF glenohumeral joint as well as elbow flexion/extension and pronation/supination and contains 22 muscles …

Comparison Of The Pull-Out Strengths Of Three Different Screws In Pedicular Screw Revisions: A Biomechanical Study, Irfan Esenkaya, Yurdaer Denizhan, Mehmet Akif Kaygusuz, Mehmet Yetmez, Mehmet Halidun Keleştemur

Faculty Publications - Mechanical Engineering

OBJECTIVES: We investigated the possible effects of three pedicular screws on axial pull-out strength in pedicular revision surgery. METHODS: Two study groups were formed from calf lumbar vertebrae. Initially, Alici pedicular screws with an outer diameter of 6.5 mm were applied (with or without tapping) to all the pedicles. All the pedicles were subjected to axial pull-out testing to induce pedicular insufficiency. Then, Alici pedicular screws with an outer diameter of 7 mm were applied to the left pedicles. The right pedicles in the two study groups were assigned to receive two different types of pedicular screws with an expandable …

Optimization Of The Seating Position In A Human-Powered Vehicle, Y. Lei, Mohamed Trabia, D. Too

Mechanical Engineering Faculty Research

Until recently, most of the human-powered vehicles (HPV) were designed focusing solely on its aerodynamics characteristic. In many of these HPV designs, the rider seating position was arbitrarily chosen without consideration of its effect on the rider's comfort and cycling effectiveness. Also, there is no guarantee that the seating position is related to maximum power output. Too (1991) used an experimental approach to determine that the rider will produce the maximum anaerobic power when the seat tube angle of a bicycle is at 75° whereas Hull and Gonzalez (1990) used an engineering approach to optimize the cycling biomechanics. However several …