Biomechanical Engineering Commons^™

Microfluidic Technology And Application In Urinal Analysis, Jiwen Xiang

LSU Doctoral Dissertations

Microfluidic technology offers numerous advantages in minimizing and integrating the traditional assays. However, the lack of efficient control components of the microfluidic systems has been hindering the widely commercialization of the technology. The research work in this dissertation focused on the development of effective control components for microfluidic applications.

A linear peristaltic pump was firstly designed, fabricated, and tested for conventional microfluidics by synchronously compressing the microfluidic channel with a miniature cam-follower system in Chapter 2. The miniature cam-follower system and microfluidic chip was prototyped using three-dimensional (3D) printing technology and soft lithography technology. Results from experimental test showed that …

Opty: Software For Trajectory Optimization And Parameter Identification Using Direct Collocation, Jason K. Moore, Antonie J. Van Den Bogert

Mechanical Engineering Faculty Publications

opty is a tool for describing and solving trajectory optimization and parameter identification problems based on symbolic descriptions of ordinary differential equations and differential algebraic equations that describe a dynamical system. The motivation for its development resides in the need to solve optimal control problems of biomechanical systems. The target audience is engineers and scientists interested in solving nonlinear optimal control and parameter identification problems with minimal computational overhead.

The Study Of An Impinging Unsteady Jet - Fluid Mechanics And Heat Transfer Analysis, Andrea Osorio

Electronic Theses and Dissertations

The high heat transfer capabilities of impinging jets have led to their widespread use in industrial applications, such as gas turbine cooling. These impinging jets are usually manufactured on the walls of super-alloy metals and are influenced by being positioned with a confined setting. Studies have been shown to enhance the heat transfer of impinging jets by fluctuating the flow which will be analyzed in this project with two designs. The first design is a self-sustaining stationary fluidic oscillator that causes a sweeping motion jet to impinge on the surface. This is investigated using Particle Image Velocimetry (PIV) to study …

Lcd 3d Printing Of A Photocurable Elastomer For Tissue Engineering, Beatriz Luiza De Souza

Electronic Theses and Dissertations

Three-dimensional scaffolding is an emerging research area in biomedical and tissue engineering. Scaffolds provide the possibility of growing tissues in a controlled environment, with desired characteristics and properties towards a specific application. A new method to 3D print biodegradable and biocompatible material called Polyglycerol Sebacate Acrylate (PGSA) is demonstrated. PGSA is essentially an acrylated form of PGS using photoinitiator to become a photocurable resin suitable for liquid crystal display (LCD) 3D printing. PGSA was selected because its rheological and crosslinking behavior (and hence its mechanical properties) can be controlled by changes in curing time, temperature, and pressure. This material has …

Tortuosity Calculations, Blood Flow Simulations, And Mechanical Testing Of Mouse Aortae, Shawn Pavey, Jessica Wagenseil

Undergraduate Research Symposium Posters

Aortic aneurysms can lead to wall rupture or dissection, which are both deadly occurrences. The risk of developing problematic aneurysms increases with age, making them a growing concern in the USA’s aging population. Thoracic Aortic Aneurysm (TAA) treatment is highly effective if the TAA is diagnosed in time, however current surgical guidelines catch less than half of fatal TAA cases. Tortuosity (related to vessel length divided by the straight distance between two points of interest) has been proposed as a supplement to diameter based diagnosis of severity of TAA progression. This study aimed to confirm the validity of that proposal …

Mimicking Blood Rheology For More Accurate Modeling In Benchtop Research, Lindsey Webb

Honors Undergraduate Theses

To confirm computer simulations and Computational Fluid Dynamics (CFD) analysis, benchtop experiments are needed with a fluid that mimics blood and its viscoelastic properties. Blood is challenging to use as a working fluid in a laboratory setting because of health and safety concerns. Therefore, a blood analogue is necessary to perform benchtop experiments. Viscosity is an important property of fluids for modeling and experiments. Blood is a shear thinning fluid, so it has a decreasing viscosity with higher shear rates. This project seeks to create a blood mimicking fluid for benchtop laboratory use. Numerous fluids with different combinations of water, …

Lower Back Biomechanics At Non-Chronic Stage Of Low Back Pain, Iman Shojaei

Theses and Dissertations--Biomedical Engineering

Prior studies have reported differences in lower back biomechanics during activities of daily living between individuals with and without chronic low back pain (LBP). Nevertheless, the literature on lower back biomechanics of patients with non-chronic LBP is scant. Therefore, the objective of this study, as the first step towards future prospective studies, was to investigate the lower back biomechanics in patients with non-chronic LBP. Case-control studies were conducted wherein measures of lumbo-pelvic coordination during bending and return tasks as well as measures of mechanical demand on the lower back during lifting tasks in the sagittal plane were investigated between patients …

Design And Analysis Of A 3d-Printed, Thermoplastic Elastomer (Tpe) Spring Element For Use In Corrective Hand Orthotics, Kevin Thomas Richardson

Theses and Dissertations--Mechanical and Aerospace Engineering

This thesis proposes an algorithm that determine the geometry of 3D-printed, custom-designed spring element bands made of thermoplastic elastomer (TPE) for use in a wearable orthotic device to aid in the physical therapy of a human hand exhibiting spasticity after stroke. Each finger of the hand is modeled as a mechanical system consisting of a triple-rod pendulum with nonlinear stiffness at each joint and forces applied at the attachment point of each flexor muscle. The system is assumed quasi-static, which leads to a torque balance between the flexor tendons in the hand, joint stiffness and the design force applied to …

Investigation Of A Self-Powered Fontan Concept Using A Multiscale Computational Fluid-Structure Interaction Model, Kyle Beggs

Electronic Theses and Dissertations

Congenital Heart Disease (CHD) occurs in about 1\% (40,000) of newborn babies each year in the United States alone. About 10.9\% (960) of whom suffer from Hypoplastic Left Heart Syndrome (HLHS) - a subset of CHD where children are born with a single-ventricle (SV). A series of three surgeries are carried out to correct HLHS culminating in the Fontan procedure where venous flow returns passively to the lungs. The current configuration for the Fontan results in elevated Central Venous Pressure (CVP), inadequate ventricular preload, and elevated Pulmonary Vascular Resistance (PVR) leading to a barrage of disease. To alleviate these complications, …

Developing A 3d In Vitro Model By Microfluidics, Hung-Ta Chien

Dissertations and Theses

In vitro tissue models play an important role in providing a platform that mimics the realistic tissue microenvironment for stimulating and characterizing the cellular behavior. In particular, the hydrogel-based 3D in vitro models allow the cells to grow and interact with their surroundings in all directions, thus better mimicking in vivo than their 2D counterparts. The objective of this thesis is to establish a 3D in vitro model that mimics the anatomical and functional complexity of the realistic cancer microenvironment for conveniently studying the transport coupling in porous tissue structures. We pack uniform-sized PEGDA-GelMA microgels in a microfluidic chip to …

Biomechanical Characterization Of Video-Recorded Short-Distance Falls Involving Children Equipped With A Biometric Device: A Pilot Study., Bret A Hilt

Electronic Theses and Dissertations

Falls are commonly used as a false history by caregivers to conceal child abuse. Determining biomechanical compatibility is a key aspect in differentiating abuse from accident. Current forensic approaches are limited in assessing biomechanical compatibility of short-distance falls involving children due to a lack of reliable witnessed falls with known injury outcomes. The goals of this pilot study were to characterize biomechanical measures and to examine differences in biomechanical measures based on child and fall characteristics in reliable witnessed video-recorded falls involving children. The results of this study will serve as preliminary data for an on-going larger study with the …

Radial And Longitudinal Motion Of The Arterial Wall: Their Relation To Pulsatile Pressure And Flow In The Artery, Dan Wang, Linda Vahala, Zhili Hao

Mechanical & Aerospace Engineering Faculty Publications

The aim of this paper is to analyze the radial and longitudinal motion of the arterial wall in the context of pulsatile pressure and flow, and to understand their physiological implications for the cardiovascular system. A reexamination of the well-established one-dimensional governing equations for axial blood flow in the artery and the constitutive equation for the radial dilation of the arterial wall shows that two waves—a pulsatile pressure wave in the artery and a radial displacement wave in the arterial wall—propagate simultaneously along the arterial tree with the same propagation velocity, explaining why this velocity combines the physical properties and …