Biomechanical Engineering Commons^™

Effects On Initial Fixation Of Cementless Tibial Trays In Total Knee Arthroplasty, Brooke Fritts Thompson

Electronic Theses and Dissertations

Bone mineral density (BMD), among other factors, largely effect the initial stability of the cementless tibial tray component in a total knee replacement (TKR), where increased motion at the tray-bone interface hinders bony ingrowth. With a lack of bony ingrowth, the cementless implant will not experience long-term success. Understanding which factors influence initial stability yields insight into surgical technique considerations and help inform a surgeon’s implant choice. The objective of this study was to evaluate factors influencing the initial stability of cementless tibial trays using a 6-degree of freedom (6-DOF) robotic joint simulator, the AMTI VIVO, and combined loading scenarios …

Development And Characterization Of A Biopolymer Direct-Write Process For 3d Microvascular Structures Formation., Xiaoming Fan

Electronic Theses and Dissertations

Engineering of bulk tissues has been limited by the lack of nutrient and waste exchange in these tissues without an adjacent capillary network. To produce microvasculature, a scaffold must be produced that provides temporary mechanical support and stimulate endothelial cell adhesion, growth, and morphogenesis into a vessel. However, current well-established techniques for producing microvasculature, such as electrospinning, are limited since they lack both the precision to control fiber placement in three-dimensional space and the ability to create fiber networks with predefined diameters to replicate the physiological microvascular progression from arteriole to capillary to venule. Our group has developed a “Direct-write” …

Computational Fluid Dynamics Investigation Of A Novel Hybrid Comprehensive Stage Ii Operation For Single Ventricle Palliation, Marwan Hameed

Electronic Theses and Dissertations

Hypoplastic left heart syndrome (HLHS) is a type of heart defect where the left ventricle is underdeveloped or not developed, resulting in only a single functioning right ventricle. Approximately 7.5% of patients with congenital heart disease are born with a single ventricle (SV) which is accompanied by a spectrum of other malformations such as atrophied ascending aorta, atrial septal defects, and ventricular septal defects (VSD). The existing three-hybrid staged surgical approach serving as a palliative treatment for this anomaly entails multiple complications and achieves a survival rate of only 50%. To reduce the trauma associated with the second stage of …

Probing The Influence Of Cx43 And Glucose On Endothelial Biomechanics, Md Mydul Islam

Electronic Theses and Dissertations

Endothelial cells (ECs) form the innermost layer of all vasculature and constantly receive both biochemical and biomechanical signals, yielding a plethora of biomechanical responses. In response to various biochemical or biomechanical cues, ECs have been documented to generate biomechanical responses such as tractions and intercellular stresses between the cell and substrate and between adjacent cells in a confluent monolayer, respectively. Thus far, the ability of endothelial tight junctions and adherens junctions to transmit intercellular stresses has been actively investigated, but the role of gap junctions is currently unknown. In addition, there is no report of the independent influence of hyperglycemia …

3d Printed Bioreactor With Optimized Stimulations For Ex-Vivo Bone Tissue Culture, Anirban Chakraborty

Electronic Theses and Dissertations

Motivation: Long term tissue survivability ex-vivo can greatly facilitate research on the influence of external stimulus (loading, radiation, microgravity) on the tissue, including mechanisms of disease transmission and subsequent drug discoveries. Bioreactors (used to culture living tissue ex-vivo) can be a valuable tool to study cell activity during physiological processes by mimicking their in-vivo native 3D environment.
Objective Statement: We have developed a compact, 3D printed bioreactor equipped with both continuous flow-perfusion and dynamic mechanical-loading stimulations, capable of maintaining ex-vivo viability of swine cancellous bone cores over a long period. Qualitative study of the cultured cores (in terms of …

Side-To-Side Comparison Of Total Shoulder Arthroplasty And Intact Function In Individuals, Sarah Rose Walden

Electronic Theses and Dissertations

Total Shoulder Arthroplasty (TSA) is a surgery which replaces the shoulder joint, or the interface between the humerus and the scapula glenoid. To test TSA success, most prior research compares patients with TSA to healthy controls. However, the shoulder anthropometry, motion, and musculature of individuals varies widely across the population making it important to assess TSA performance in individuals. The overall goal of this study is to determine if patients with one of two TSA implant designs on one side achieve the same range of motion as their intact side, and if so to find if they compensate using increased …

Materials Design With Polylactic Acid-Polyethylene Glycol Blends Using 3d Printing And For Medical Applications., Jeremiah R. Bauer

Electronic Theses and Dissertations

This thesis is an examination of two material systems derived from polylactic acid (PLA) and polyethylene glycol (PEG). PLA is a polymer commonly sourced from renewable sources such as starches and sugars. It is a relatively strong, biodegradable polymer, making it ideal for use in the body. Even though it has a relative high strength, PLA is also brittle leading to the use of plasticizers to increase flexibility. One such plasticizer is PEG, which is a material that can exist at room temperature as either a thin liquid, or a hard waxy solid depending on the molecular weight. The first …

The Study Of An Impinging Unsteady Jet - Fluid Mechanics And Heat Transfer Analysis, Andrea Osorio

Electronic Theses and Dissertations

The high heat transfer capabilities of impinging jets have led to their widespread use in industrial applications, such as gas turbine cooling. These impinging jets are usually manufactured on the walls of super-alloy metals and are influenced by being positioned with a confined setting. Studies have been shown to enhance the heat transfer of impinging jets by fluctuating the flow which will be analyzed in this project with two designs. The first design is a self-sustaining stationary fluidic oscillator that causes a sweeping motion jet to impinge on the surface. This is investigated using Particle Image Velocimetry (PIV) to study …

Lcd 3d Printing Of A Photocurable Elastomer For Tissue Engineering, Beatriz Luiza De Souza

Electronic Theses and Dissertations

Three-dimensional scaffolding is an emerging research area in biomedical and tissue engineering. Scaffolds provide the possibility of growing tissues in a controlled environment, with desired characteristics and properties towards a specific application. A new method to 3D print biodegradable and biocompatible material called Polyglycerol Sebacate Acrylate (PGSA) is demonstrated. PGSA is essentially an acrylated form of PGS using photoinitiator to become a photocurable resin suitable for liquid crystal display (LCD) 3D printing. PGSA was selected because its rheological and crosslinking behavior (and hence its mechanical properties) can be controlled by changes in curing time, temperature, and pressure. This material has …

Investigation Of A Self-Powered Fontan Concept Using A Multiscale Computational Fluid-Structure Interaction Model, Kyle Beggs

Electronic Theses and Dissertations

Congenital Heart Disease (CHD) occurs in about 1\% (40,000) of newborn babies each year in the United States alone. About 10.9\% (960) of whom suffer from Hypoplastic Left Heart Syndrome (HLHS) - a subset of CHD where children are born with a single-ventricle (SV). A series of three surgeries are carried out to correct HLHS culminating in the Fontan procedure where venous flow returns passively to the lungs. The current configuration for the Fontan results in elevated Central Venous Pressure (CVP), inadequate ventricular preload, and elevated Pulmonary Vascular Resistance (PVR) leading to a barrage of disease. To alleviate these complications, …

Biomechanical Characterization Of Video-Recorded Short-Distance Falls Involving Children Equipped With A Biometric Device: A Pilot Study., Bret A Hilt

Electronic Theses and Dissertations

Falls are commonly used as a false history by caregivers to conceal child abuse. Determining biomechanical compatibility is a key aspect in differentiating abuse from accident. Current forensic approaches are limited in assessing biomechanical compatibility of short-distance falls involving children due to a lack of reliable witnessed falls with known injury outcomes. The goals of this pilot study were to characterize biomechanical measures and to examine differences in biomechanical measures based on child and fall characteristics in reliable witnessed video-recorded falls involving children. The results of this study will serve as preliminary data for an on-going larger study with the …

Material Properties Design Using Simulations And Experiments For Powder Injection Molding Of Lead Zirconate Titanate (Pzt)., Bhushan Pramod Bandiwadekar

Electronic Theses and Dissertations

Powder injection molding (PIM) process simulations can be performed to minimize the number of injection molding experiments by estimating material properties necessary for PIM simulations. In current work, lead zirconate titanate (PZT) powder-polymer binder feedstock was compounded for 45 vol. % and 52 vol. % solids loading. PIM experiments on designed micro-pillar array geometry were performed using 52 vol. % PZT. Using PIM experiments results as basis, PIM simulations were performed on designed micro-pillar array geometries to understand the effectiveness of PIM simulations with the use of estimated feedstock properties in predicting molding behavior that have micro-features. Additionally, PIM simulations …

Biomechanical Testing Of An Exercise For Strengthening The Proximal Femur., Alyssa Osbourne

Electronic Theses and Dissertations

Based on the principles of cutting edge bone remodeling research, a unique therapeutic exercise device was designed specifically to improve bone quality at the most critical location of the proximal femur prone to fracture: the superior-lateral femoral neck where the fracture first initiates during a fall. The exercise/device is intended to work by inducing enough strain in the bone to stimulate the body’s natural bone remodeling mechanisms to increase bone density in the proximal femur and consequently prevent a fracture from arising if a fall to the side does occur.

In order to test the proposed exercise, experiments simulating the …

Development And Evaluation Of A Biocompatible Electroactive Sensor For Continuous Blood Pressure Measurement., Scott D. Cambron

Electronic Theses and Dissertations

Piezo-active composites have been implemented for sensing and transduction for decades. The 0-3 ceramic/polymer composite is one of the most common composite types used for sensing applications, owing to their tailorable properties of the two-phase composition, consisting of a three-dimensionally connected polymer/rubber matrix (inactive phase) with a dispersion of isolated piezo-ceramic particles (active phase). This thesis describes a method to develop novel biocompatible perivascular band comprised of a two-phase piezo-active composite to be fabricated using simple manufacturing processes. Biomaterials such as tissue scaffolds comprised of silk fibroin (SF) and chitosan (CS), and biocompatible soft rubbers will be implemented as the …

Bio Inspired Lightweight Composite Material Design For 3d Printing, Kaushik Thiyagarajan

Electronic Theses and Dissertations

Lightweight material design is an indispensable subject in product design. The lightweight material design has high strength to weight ratio which becomes a huge attraction and an area of exploration for the researchers as its application is wide and increasing even in every day-to-day product. Lightweight composite material design is achieved by selection of the cellular structure and its optimization. Cellular structure is used as it has wide multifunctional properties in addition to the lightweight characteristics. Applications of light weight cellular structures are wide and is witnessed in all industries from aerospace to automotive, construction to product design. In this …

Microfluidic Platform For Impedance Characterization Of Endothelial Cells Under Fluid Shear Stress., Vanessa Velasco

Electronic Theses and Dissertations

Endothelium dysfunction has been associated with many pathophysiological processes leading to cardiovascular diseases. Studying endothelium behavior is vital to understand the onset, prevention, and treatment of such diseases. Electrical impedance spectroscopy has been shown to provide a real-time in vitro evaluation of cell behavior including cell monolayer permeability. However, the majority of published work has been primarily with static cell culture models or macro-scale models that do not properly represent the physiological sizes, structures, and environmental conditions of human blood vessels. Within this dissertation, the design, fabrication, characterization, and application of a microfluidic impedance platform is presented for the in …

Finite Element And Probabilistic Analysis Of Soft Tissue Structures Of The Human Lumbar Spine, Dana Joseph Coombs

Electronic Theses and Dissertations

Human lumbar spine mechanics are influenced by soft tissue structures. Understanding and properly modeling these structures can help determine pathology, treatment, and implant design and performance. Finite element models of the L4-L5 level of the lumbar spine are often used, which include a representation of the intervertebral disc and spinal ligaments. Validation of these models are typically based on torque rotation data from a single subject or the models use average properties reported in literature. However, experimental testing reports variation up to 40% in ligament stiffness and even greater variability for annulus fibrosis properties. Probabilistic approaches enable consideration of the …

Statistical Modeling To Investigate Anatomy And Function Of The Knee, Lowell Matthew Smoger

Electronic Theses and Dissertations

The natural knee is a hinge joint with significant functional requirements during activities of daily living; as a result, acute and chronic injuries can occur. Pathologies are influenced by joint anatomy and may include patellar maltracking, cartilage degeneration (e.g. osteoarthritis), or acute injuries such as meniscal or ligamentous tears. Population variability makes broadly applicable conclusions about etiology of these conditions from small-scale investigations challenging. The work presented in this dissertation is a demonstration of statistical modeling approaches to evaluate population variability in anatomy of the knee and function of its tibiofemoral (TF) and patellofemoral (PF) joints. Three-dimensional (3D) computational models …

Inverse-Consistent Determination Of Young's Modulus Of Human Lung, Behnaz Seyfi Noferest

Electronic Theses and Dissertations

Human lung undergoes respiration-induced deformation due to sequential inhalation and exhalation. Accurate determination of lung deformation is crucial for tumor localization and targeted radiotherapy in patients with lung cancer. Numerical modeling of human lung dynamics based on underlying physics and physiology enables simulation and virtual visualization of lung deformation. Dynamical modeling is numerically complicated by the lack of information on lung elastic behavior, structural heterogeneity as well as boundary constrains. This study integrates physics-based modeling and image-based data acquisition to develop the patient-specific biomechanical model and consequently establish the first consistent Young's modulus (YM) of human lung. This dissertation has …

Probabilistic Musculoskeletal Simulation Methods To Address Intersegmental Dependencies Of The Knee, Hip, And Spine, Casey A. Myers

Electronic Theses and Dissertations

Orthropaedic clinical practice in the area of the knee, hip, and spine has benefited from the concept of regional interdependence, where interventions applied to one region can influence the outcome and function of other regions of the body that may be seemingly unrelated to the applied intervention. An understanding of the biomechanical mechanisms that describe clinical practice involving knee, hip, and spine regional interdependence can improve treatment of a wide range of pathological conditions. Improvement in this area can be particularly impactful on the outcomes of patients with total joint replacement, where pathology and compensatory strategies develop during multi-joint interactions. …

Evaluation Of Novel High-Density Emg Feedback Parameters On The Spatial Distribution Of Trapezius Muscle Activity, Brecca M. Gaffney

Electronic Theses and Dissertations

Each year, 17.9% of adults working in a computer-dominated work environment develop an episode of chronic neck and shoulder pain. An effective treatment method for chronic pain is postural correction through therapist. The understanding of the relation between cervicoscapular posture and trapezius muscle activity is not fully understood because the anatomy of the scapula is not accessible for direct observation. Until recently, the spatial distribution of trapezius muscle activity could not be measured due to the limitation in size of detection zone in traditional bipolar electrodes. The primary goal of postural correction when treating cases of chronic neck and shoulder …

Cavitation In Pharmaceutical Manufacturing And Shipping, Donn Sederstrom

Electronic Theses and Dissertations

Therapeutic proteins are used to successfully treat hemophilia, Crohn's Disease, diabetes, and cancer. Recent product recalls have occurred because of sub-visible particle formation resulting from the inherent instability of proteins. It has been suggested that particle formation is associated with late stage processing steps of filling, shipping, and delivery. Previous work at the University of Denver demonstrated that fluid cavitation can generate a large number of sub-visible protein particles in ultra clean formulations, but that mitigation can be achieved with fluid property manipulation. The goal of this research was to (1) assess the risk of cavitation under common pharmaceutical manufacturing …

Label-Free Biochemical Recognition Using Mems Resonators For Microarray Technology, Babak Tousifar

Electronic Theses and Dissertations

Highly sensitive biosensors capable of detecting and characterizing smallest quantities of cellular and molecular targets are needed in pharmaceutical and medical diagnostics industries. In this work, the importance of biological target recognition specifically proteins through microarray technologies has been discussed and the most successful tools and techniques have been studied. Moreover, a thermally actuated Micro Electro-Mechanical Systems (MEMS) resonator has been demonstrated and fabricated in this work as an accurate, reliable and low cost biotechnology tool. As a proof of concept, amine to epoxide coupling of octadecylamine to functionalized silicon dioxide surface have been shown through resonator frequency monitoring. The …