Acoustics, Dynamics, and Controls Commons^™

Vibration Isolation For Scanning Tunneling Microscope, Seth Ewing, Ryan Mcmullen, Jason Behrens, Stephen Deherrera

Mechanical Engineering

Scanning Tunneling Microscopy (STM) works by scanning a fine metal wire over a conductive sample in order to image samples on the atomic level. The microscope uses a feedback loop with a PID controller to maintain a constant tunneling current between the sample and the tip. In order to obtain clear imaging at the atomic level, the microscope and the sample need to be isolated from external vibrations in a vacuum chamber. The scope for this project is to build and test a single-stage vibration isolation system that effectively attenuates the amplitude of external vibrations acting on the microscope. This …

Inverted Fluorescence Microscope, Matthew B. Pfeiffer, Spencer George Hann, Thomas James Eggenberger, Trevor Lee Blythe

Mechanical Engineering

Team F13 is composed of Trevor Blythe, Spencer Hann, Matthew Pfeiffer, and Thomas Eggenberger. We are all majoring in mechanical engineering and in our final year of study here at Cal Poly San Luis Obispo. This project is a continuation of a 2019-2020 senior project. The previous team designed and built a functioning inverted fluorescence microscope (IFM) from scratch. This device was created as a lab tool for undergraduate students to be able to perform experiments on microfluidic devices constructed in Cal Poly’s Microfabrication Laboratory. Although substantially functional, several design constraints had not yet been met. Our team has improved …

Project G.H.O.S.T., Matthew Morell, Austin Conrad, Zackeris Gordon, Conan Estes

Mechanical Engineering

Project G.H.O.S.T aimed to produce a model transmission with a control system for high performance/racing electric vehicles to utilize the full capability of the electric motor at higher speed applications. Current electric vehicles have a large amount of torque and use a fixed gear ratio that compromises between both high and low speeds with performance peaking around 65 miles per hour. A typical electric motor used in this application has approximately 1800 ft-lbs of torque up to 5,000 rpm. Past approximately 5,000 rpm, the torque rapidly drops off and so does the overall vehicle performance. Though transmissions exist that could …

Vibration Isolation System, Bradley Y. Kwan, Bailey Groh, Max Wu, Nicole Yen

Mechanical Engineering

The Vibration Isolation System Senior Project is a collaborative group project between its sponsor, Maxar Technologies, and a team of students from Cal Poly - SLO to effectively design, manufacture, and test a structural assembly for satellites, isolating vibrations during launch and orbit conditions. After initial sponsor contact, requirements and needs were set which dictated deliverables for the senior project group. The group performed analyses to validate all design decisions, including a modified concept and design direction, selection of a prototype viscoelastic damping material, preliminary testing to validate design specifications, and detailed design and analysis toward a finalized design. Instead …

Electronic Cvt - Controls, Alec William Hardy, Jessalyn Leora Ann Bernick, Nicholas Esteban Capdevila, Tristan Charles Perry

Mechanical Engineering

The following document outlines the design process, manufacturing, and testing of the control system for an electronically controlled continuously variable transmission (ECVT). This control system was integrated into the custom designed and manufactured mechanical transmission system created in parallel by another senior project group. The transmission was designed for use in the Cal Poly Baja SAE vehicle. Through researching customer needs, competition requirements, previous and alternate CVT designs, and vehicle characteristics, we were able to determine the requirements and specifications for our unique system. Input, output, speed, and durability requirements guided our hardware selection. The primary components which comprised our …

Autonomous Vehicles Operating Collaboratively To Avoid Debris And Obstructions, Toan T. Le, Cole W. Oppenheim, James H. Gildart, Kyle M. Bybee

Mechanical Engineering

The purpose of this project is to demonstrate the safety and increased fuel efficiency of an automated collision avoidance system in collaborative vehicle platooning. This project was cosponsored by Daimler Trucks North America headquartered in Portland, Oregon, as well as Dr. Birdsong, and Dr. DeBruhl of Cal Poly. The mechanical engineering team consists of Cole Oppenheim, James Gildart, Toan Le, and Kyle Bybee who worked in coordination with a team of computer engineers. Vehicle platooning is a driving technique to increase the fuel efficiency of a group of vehicles by following a lead vehicle closely to reduce the drag experienced …

Ultraviolet Imager Application For A Cube Satellite, Jason Grillo, Troy Hajjar, Brady Hill

Mechanical Engineering

This document serves as the final design review (FDR) report for the 2018 Cal Poly CubeSat Ultraviolet Imager senior project, sponsored by UC Berkeley Space Sciences Laboratories (SSL). SSL wants to monitor the ionosphere above Earth to gain a better understanding of its properties and particle interactions. Far Ultraviolet (FUV) imaging is a good way to obtain high quality images of the ionosphere and the Earth's auroras, and advancement in optic technologies have made cube satellites (CubeSats) an ideal vessel for a FUV imager, as they are relatively low-cost, lightweight, and can be repeatedly deployed. These CubeSat FUV imagers could …

Wheelie King Trainer And Controller, Michael C. Uytingco, Paul E. Hubner, Dmitriy Petrovykh

Mechanical Engineering

The ``wheelie'' is a popular, classic bicycle trick which novice bicyclists often attempt as an introduction to advanced bike tricks. However, many are hesitant to try due to the risks and safety hazards associated with performing one. The purpose of this project is to create an on-board system which will assist a user in maintaining a wheelie after achieving the required position while incorporating safety mechanisms to prevent the user from injuring themselves or others. Additional requirements of the system are non-obstructive features and seamless transitioning between wheelie conditions.

Upon researching the state of wheelie technology, existing products, such as …

Mobile Opera Backdrop, Juan Villalobos, Robbie Behlman, Kevin Valencia

Mechanical Engineering

Opera San Luis Obispo requires an acoustically projecting stage backdrop for their future plan of deploying a mobile opera house. The custom stage backdrop must be low-cost, easy to assemble and must project the performance sound to outdoor audiences. Other design requirements include being transportable in a step van, the ability to be assembled quickly by a crew of two, resistance to various outdoor conditions, the ability to mount accessories from the walls, and should meet a budget of $5,000. With the scope of the project understood, the three-quarter project is outlined. During the first quarter, the main deliverables included …

Museum Wave Tank Design, David James Streng, Lisa Michelle Dischinger, John Frederick Niemoller

Mechanical Engineering

The Santa Maria Discovery Museum would like to add a tsunami wave tank to be one of their demonstrations. The wave tank needs to draw the attention of their young crowd and be educationally informative about the shapes and effects of waves. As this is a museum demonstration for children, the structure, user interface, and wave making mechanism must be durable.

We are a senior project team from California Polytechnic State University that worked on this project with Allan Hancock College and Stanford University. We created waves by rapidly moving a plunger vertically in the water column. This project allows …

Dyno-Mite Redesign, Brandon Joseph Miller, Daniel Robert Hoffman, Richard Demedici Young

Mechanical Engineering

The Cal Poly Mechanical Control Systems Laboratory currently employs an outdated device, known as the Motomatic, to teach students about various motor characteristics and control methods. These include open-loop vs. closed-loop control, speed vs. position control, and DC motor response curves. The current device does not function properly and produces unreliable data due to overwhelming non-linear effects such as stiction and shaft misalignment. Our team was tasked with designing a replacement device that retains many of the same educational goals as the original lab procedure, while also adding new educational goals pertaining to the device system dynamics. The new apparatus, …

Guided Target Control System Final Design Report, John Barry, Zachary Eagan, Ryan Mackintosh

Mechanical Engineering

Daimler Automotive, the parent company of Mercedes-benz requires improved methods for testing their Autonomous Emergency Braking Systems. To this end they have presented a series of four senior projects to California Polytechnic State University in San Luis Obispo. One of the Projects is to build a facsimile of a human crossing the street. The other three projects of which this is a part; are to produce an autonomous car facsimile. These projects are intended for use in testing new Autonomous Emergency Braking Systems and may serve as the basis for future senior projects.

Small-Scale Intelligent Vehicle Design Platform, Christopher Grant, Jay Miley, Evan Phillips

Mechanical Engineering

Intelligent Vehicle Design is a growing field with the potential to save many lives by actively minimizing the impacts of human error. Though there are many ways to research intelligent vehicle control, full-scale implementations are expensive and dangerous and computer simulations have extremely steep learning curves. Researchers and students need an accessible, adaptable, and robust development platform to rapidly create and test autonomous control algorithms. While small-scale platforms are often designed from the ground up for specific projects, this requires analysis, design, and manufacture. The goal of this project is to develop a small-scale intelligent vehicle that can be configured …

3-Axis Automated Probe Traverse For Aerodynamic Testing, Tananant Boonya-Ananta, Ricky Wai, Zander Oostman, Teyvon Brooks

Mechanical Engineering

Our primary objective is to design, build, and test an automated traverse to hold measurement probes in Cal Poly’s low speed wind tunnel. The device should cause minimal flow disturbance. It’s movements must be able to cover eighty percent of the three-dimensional test section. The device should have a mounting point for interchangeable probes. The assembly is to be integrated with the current frame structure on the wind tunnel test section, and should allow very minimal deflection of the measurement probe. The user should be able to control the motion of the traverse via a computer interface which supports automatic …

Magnetic Bearing For Bently Nevada Rk4 Rotor Kits, Sean Fowler, Garrett Olson

Mechanical Engineering

Active Magnetic Bearings (AMB) are contact free bearings that support loads by magnetic levitation. This is accomplished by generating magnetic forces with electric current through a series of electromagnets surrounding a suspended rotor mass. Along with a set of electromagnets, an AMB assembly also consists of power amplifiers for each electromagnet, a controller, and proximity sensors. The proximity sensors provide rotor position feedback to the control system, which modulates power to the amplifiers [4]. Magnetic bearings are used in several industrial applications today, including but not limited to compressors, turbines, pumps, motors, and generators. Advantages of their utility include very …

Low Cost Metal Chip Separator, Alek Linquist, Kale Mckinney, Ryan Jones

Mechanical Engineering

We were tasked by Micro-Vu to design, build, and test a small-scale low-cost metal chip separator to operate on one of their 24/7 mills. The goal of the project was to separate the steel and aluminum chips coming off of the mill’s chip conveyor to end up with a bin of 99% pure aluminum by mass. To accomplish this goal we first brainstormed various possible ideas and performed small scale tests the best ones. After further review we determined the best solution to this problem was a design that involved a cycling magnetic backing that would pull steel out of …

Deltronic Solutions Delta 3d Printer, Ramon Santos, Justin James, Taylor Chris, Stephen Marshall, Paul Maalouf

Mechanical Engineering

The Delta 3D Printer project is a 2014-2015 Cal Poly ME senior project sponsored by Dr. Jose Macedo, Professor and Department Chair of the Cal Poly IME Department; Yaskawa America, Inc., industry-leading producer of high-quality electronic drives and motors; and Bell-Everman, Inc., producer of high-precision embedded motion systems. The Delta 3D Printer project was conceived by Dr. Macedo as a collaboration between Cal Poly engineering and Yaskawa America. The majority of delta 3d printers on the market utilize stepper motors to control the print head motion. The 3D printer for this project was designed to use servo motors instead of …

Wingtip Dynamics Simulator, Eugene Fox, Nick Rodriguez, Steven Rieber

Mechanical Engineering

Raytheon is a defense contracting company with an electronic warfare division that is developing a radio frequency signal triangulation system. Part of the focus in improving this technology is the need for accurate and real time locational knowledge of the signal receivers, which are located at the tips of aircraft wings. Due to turbulence during flight, the fluttering motion of the wings alter the distance and angle relationships of the two receivers and add noise to the received signal data, which negatively affect the triangulation estimates. To mitigate this error caused by the wing flutter, Raytheon is developing a software …

The Icon Horn Loudspeaker, Vincent Phan

Mechanical Engineering

A horn loudspeaker in layperson terms is essentially taking a megaphone and integrating it into a standard speaker. Similar to a cheerleader yelling into a megaphone, the horn loudspeaker will amplify the sound from the speaker with no additional power needed. Using standard speaker horn theory, the geometry of the “megaphone” can be engineered to tune the acoustic performance tailored to loudness and/or specific acoustics frequencies. The horn contours are similar to traditional orchestra instruments such as the French horn, trumpet, and tuba. The iconic beauty of a horn married with the quantitative engineering theory creates an aesthetic yet functional …

Team Nathan Suspension, Frankie J. Wiggins, Alex D. Seitz, Justin P. Bautista

Mechanical Engineering

Nathan Cooper is an 8-year old boy with Spinal Muscular Atrophy (SMA). SMA has affected Nathan’s muscle development and requires him to use the Standing Dani™ mobility device. The Standing Dani is a motorized standing wheelchair, or Wheelstand. Nathan controls and uses it to get around. Though the Standing Dani performs well for most functions, it has some distinct issues. The primary issue that this project addresses is its lack of suspension and the discomfort that Nathan feels as a result. After talking with our client, we developed several specifications generally related to geometry, safety, vehicle dynamics, and reliability. Many …

An Assessment Of Acoustic Contrast Between Long And Short Vowels Using Convex Hulls, Erin F. Haynes, Michael Taylor

Mechanical Engineering

An alternative to the spectral overlap assessment metric (SOAM), first introduced by Wassink [(2006). J. Acoust. Soc. Am. 119(4), 2334–2350], is introduced. The SOAM quantifies the intra- and inter-language differences between long–short vowel pairs through a comparison of spectral (F1, F2) and temporal properties modeled with best fit ellipses (F1 × F2 space) and ellipsoids (F1 × F2 × duration). However, the SOAM ellipses and ellipsoids rely on a Gaussian distribution of vowel data and a dense dataset, neither of which can be assumed in endangered languages or languages with limited available data. The method presented in this paper, called …

Automated Foosball Table, Jim R. Stefani, Alex J. Herpy, Brett Gordon Jaeger, Kevin S. Haydon, Derek Alan Hamel

Mechanical Engineering

This project is the second iteration of an automated foosball table for Yaskawa America as a trade show display. The table is meant to provide an interactive experience which highlights the speed and precision of the Yaskawa hardware. The first iteration of the project was mainly focused on creating the physical hardware for the system and to begin the basic programming for the system. This phase of the project was focused on finalizing the physical hardware of the system, implementing the vision system and to continue the basic programing of the system AI. A third team will be assigned to …

High Temperature Filter Test Unit Upgrades, Blair Frandeen, Will Schill, Erick Shewmaker, Joshua Turgeon

Mechanical Engineering

The purpose of this project was to improve the existing High Temperature Filter Test Unit (HTTU) by optimizing performance and adding new features. These features include viewing ports and a camera system for observation of tests, a leak detection system, and a flame impingement system. Additional considerations included improving the current operation of the HTTU by reducing test time and energy loss. The HTTU is designed to test High Efficiency Particulate Air (HEPA) filters at temperatures up to 1300 ˚F, creating conditions which simulate a fire in a chemical processing facility. The HTTU was originally built as a Cal Poly …

Autonomous Collision Avoidance, Thomas Stevens, Elliot Carlson, Ian Painter

Mechanical Engineering

A steering controlled, autonomous collision avoidance system has been developed by California Polytechnic State University. This system represents a step in the direction of fully autonomous driving, while allowing the driver to maintain control of the vehicle during normal driving conditions. In the case of an imminent collision, the system removes control of the vehicle from the user and autonomously steers around the obstacles. The final system is able to avoid two static obstacles with a 95% pass rate and one moving obstacle with a 50% pass rate. With full scale, fleet wide, implementation of this system it is expected …

Architectural Engineering Earthquake Shake Table, Garrett Gudgel, John Whitmer, Brandan Williams

Mechanical Engineering

The Architectural Engineering Department at California Polytechnic State University, San Luis Obispo, owns and operates a single-axis earthquake shake table that previously was only capable of basic wave motion. After implementing a computer based interface to the existing system, Mechanical Engineering student seniors were able to create control algorithms that can take existing or user created acceleration data from earthquakes as well as any user defined position data to be accurately run on the earthquake shake table.

Rebounder Fatigue Test Machine, Caroline Reeves, Will Robertson, Ethan Flory

Mechanical Engineering

JumpSport, a company that designs and sells trampolines and trampoline accessories, has sponsored this senior project team to design, build, and test a trampoline fatigue test machine. The machine must simulate a person jumping on the trampoline to test the life of JumpSport’s fitness trampolines and kids’ trampolines. Partway through the design process, the objectives were altered and this senior project team was tasked with merging with another Cal Poly senior project group to create an all-inclusive test machine to accommodate both full-trampoline testing and individual bungee cord testing.

The final design is centered on a slider crank linkage driven …

Hepa Filter Evaluation Furnace Control Unit, Matt Gainer, Marc Goupil, Andrew Woolrich

Mechanical Engineering

No abstract provided.

Human Powered Helicopter: Rotor Structure, Joseph Ram, Juan Carlos Olvera

Mechanical Engineering

The following report encompasses the Human Powered Helicopter Rotor Team’s conceptual models and ideas based on research and modeling analysis. The following gives an overview of material researched, concept generation, analyzation, manufacturing, and testing for a rotor structure to be installed in a Human Powered Helicopter.

Supermileage Chassis Dynamometer, Jose Garcia, Steve Janning, Timothy Lui, Kyla Purvis

Mechanical Engineering

This report describes the final design and analysis of a hydraulic chassis dynamometer as a testing tool for California Polytechnic State University, San Luis Obispo Supermileage Vehicle Team (CPSMV). Literature review was conducted to understand the various types of chassis dynamometers on the market as of the year 2011. After rigorous research, it was determined that a hydraulic system was the best system for a chassis dynamometer in terms of functionality, performance, and cost. Critical study of hydraulics, dynamometers, and data acquisition systems (DAQ) was followed by a complete design of a hydraulic system. The chassis dynamometer proposed in this …

California Olive Ranch Hedger, Tyler Enos, Seth Abbott, David Gamba

Mechanical Engineering

The purpose of this project is to evaluate the problems of the current KCI (Kingsburg Cultivator Incorporated) olive tree hedger in use at California Olive Ranch (COR) in Artois, CA, and then correct these problems which should yield a better performing, more efficient, and reliable machine. These problems include: the hydraulic oil temperature getting too high, the saw blades not having enough horsepower, and poor cutting performance due to operator error as well as terrain variations.