Acoustics, Dynamics, and Controls Commons^™

Interactive Lego Girl Scout Arm, Chris Suzuki, Emi Okuyama, Bryson Shores, Karina Sandoval

Mechanical Engineering

This Senior Project Report document outlines the senior design project for Girl Scouts of California’s Central Coast (GSCCC) led by a team of four Mechanical Engineering students at California Polytechnic State University, San Luis Obispo. The project encompasses the researching, designing, prototyping, and testing of a LEGO robotic arm for the Girl Scouts to learn more about STEM (Science, Technology, Engineering, and Mathematics) and provide support to each Girl Scouts cookie sales in their stores. Their goal was to build a LEGO robotic arm that will interact with customers at the Girl Scout stores and promote the girl scouts' interest …

Ambient Temperature Phase Change Launcher, Johnny Molloy

Senior Honors Projects

JOHNNY MOLLOY (Mechanical Engineering) Ambient Temperature Phase Change Launcher Sponsor: Bahram Nassersharif (Mechanical Engineering)

Deployment of payloads stored in watertight cylindrical bodies in underwater environmental conditions are of interest to the marine and naval community. The proposed work will investigate the possibility of using inert carbon dioxide gas compressed into its liquid state and stored under pressure to launch payloads by means of expansion from a cylindrical tube. To suit the needs of the Naval Undersea Warfare Center (NUWC), this launching system must fire from up to 14 ft underwater, have two degrees of freedom, and the payload must not …

R/C Baja: Drivetrain, Connor T. Donovan

All Undergraduate Projects

The Central Washington University Mechanical Engineering Technology Department hosts an annual R/C Baja competition in which R/C cars fabricated by student teams are put through a series of courses and tests to determine which team's vehicle is best. The goal of this project was to create a functioning drivetrain that conveys power from the battery to the wheels and provides control of the vehicle. A list of requirements for the drivetrain was created to ensure that the vehicle will not only function, but that it will actually succeed in the competition. These requirements included that the vehicle must achieve a …

Jcati Carbon Fiber Shredder 2022, Parker Sudderth

All Undergraduate Projects

This project is a potential solution to keep the carbon fiber waste from airplane manufacturing to a minimum, sponsored by the Joint Center for Aerospace Technology Innovation (JCATI). The design and assembly will be scalable for future industry application. The overall design of the whole carbon fiber recycler consists of a crusher, shredder, and oven. This report is on the caron fiber shredder module. The shredder is tasked with being able to shred the delaminated carbon fiber scrap that directly comes from the crusher. The operation must produce shreds in the proper size to be gathered and delivered to the …

Quickcut Waterjet Cutter, Kennedy Dunn, Jacob Storrow, Benjamin Laughrey

Williams Honors College, Honors Research Projects

The QuickCut Waterjet Cutter was created in 2019 as a senior design project. This is the third iteration of the waterjet cutter. The goal of this project was to create an operable CNC waterjet cutter that is able to cut 1/16” tensile specimens consisting of nonferrous metal or plastic. This machine will be utilized in the Manufacturing Laboratory at the University of Akron to provide education to interested students on the waterjet cutting process, how it operates, and industrial application of the technology. Waterjet cutting is a subtractive manufacturing process which is recognized for its specialized applications such as cutting …

Human Powered Vehicle Team Challenge, Sydney Nedlik, Spencer Brodie, Maria Griffin, William Schell, Ryan Serraglio

Williams Honors College, Honors Research Projects

Design and build a Human Powered Vehicle in a team of five. Compete at the ASME HPVC competition in March of 2022. Re-establish the Human Powered Vehicle Team at the University of Akron.

Grinding And Super-Finishing Test Machine Project, Michael Simon

Williams Honors College, Honors Research Projects

A research project in The University of Akron to study grinding and super-finishing of silicon nitride ceramic was initiated by Dr. Siamak Farhad and sponsored by the Timken Company, with the assistance of undergraduate students Michael Simon, Ryan Hosso and Mathew Rozmajzl. The study required analysis of forces and scratches generated during grinding processes of silicon nitride samples. A testing assembly was designed and constructed to record the forces generated during grinding and super-finishing of silicon nitride samples in a computer-numerical-control machine. Silicon nitride samples were subjected to desired grinding and super-finishing operations and all forces generated during the process …

Multi-Platform Suppressor Design Project, Wyatt A. Openshaw, Alex B. Chiples

Williams Honors College, Honors Research Projects

The Multi-Platform suppressor is a design that is meant to bridge the gap in the suppressor market by being compatible and configurable with both rifle and pistol platform firearms. In the specific design and prototype referenced in this report, the Multi-Platform suppressor was designed to be used with 9mm pistol and 5.56x45mm rifle calibers with safety, effectiveness, and practicality in mind. To achieve this, the suppressor is configurable, utilizing a Nielsen device in the pistol configuration and a solid mount adapter that replaces the Nielson device piston and spring while in the rifle configuration. This allows the suppressor to retain …

Cnc Feed Drive Control, Ryan J. Funchess, Caleb P. O'Gorman, Nick J. Desimone, Juan M. Majano, Samuel K. Wong

Mechanical Engineering

This document serves as the Final Design Report (FDR) for a senior project developed by our team: four senior Mechanical Engineering students and one computer engineering student at California Polytechnic State University, San Luis Obispo (Cal Poly). While the project was completed for, and sponsored by, Professor Simon Xing of Cal Poly, the remainder of the university’s controls professors will be indirectly benefited from this project. Our goal was to design and implement a functional CNC Feed Drive to be used for educational demonstrations and data collection. This document discusses our early product research and benchmark goals, which established constraints …

Adjustable Height Pedestal Grinder Stand, Josef Zagorski, Zachary Wedel, Michael Sitar, Daniel Zevenbergen

Mechanical Engineering

Pedestal grinders are one of the most common machines found in machine shops today. The current industry standard for mounting a grinder is on a fixed single pillar, cast iron pedestal. A fixed pedestal allows for no vertical adjustment for shop users of different sizes and is a safety hazard. This report further defines this problem and proposes an iterative design process to meet the needs and wants of the customer. The adjustable-height pedestal grinder stand Senior Project team used this problem and design process to successfully complete the project within the allotted time. The first major deliverable and milestone …

Inverted Fluorescence Microscope, Matthew B. Pfeiffer, Spencer George Hann, Thomas James Eggenberger, Trevor Lee Blythe

Mechanical Engineering

Team F13 is composed of Trevor Blythe, Spencer Hann, Matthew Pfeiffer, and Thomas Eggenberger. We are all majoring in mechanical engineering and in our final year of study here at Cal Poly San Luis Obispo. This project is a continuation of a 2019-2020 senior project. The previous team designed and built a functioning inverted fluorescence microscope (IFM) from scratch. This device was created as a lab tool for undergraduate students to be able to perform experiments on microfluidic devices constructed in Cal Poly’s Microfabrication Laboratory. Although substantially functional, several design constraints had not yet been met. Our team has improved …

Real-Time Monitoring Of Fdm 3d Printer For Fault Detection Using Machine Learning: A Bibliometric Study, Vaibhav Kisan Kadam, Satish Kumar, Arunkumar Bongale

Library Philosophy and Practice (e-journal)

Additive Manufacturing has wide application range including healthcare, Fashion, Manufacturing, Prototypes, Tooling etc. AM techniques are subjected to various defects that may be printing defects or anomalies in machine. There is gap between current AM techniques and smart manufacturing since current AM lacks in build sensors necessary for process monitoring and fault detection. Both of these issues can be solved by incorporating real-time monitoring into AM. So the study is carried out to identify recent work done in AM to improve current system. For this bibliometric study Scopus database is used, study is kept limited to year 2010-2021 and English …

Noise Control In Sorting Conveyors, Eyra Herrera

Mechanical Engineering Undergraduate Honors Theses

E-commerce has increased the necessity of effective material handling equipment in warehouses and distribution centers. Sorter conveyors systems facilitate material handling by providing a reliable and automated system to classify and distribute products in a gentle and rapid manner. With the steady increase of speed in sorter conveyors to satisfy today’s industry demand, some systems have started to produce high noise levels that could potentially affect workers’ health. Since decreasing the speed of these conveyors is not a viable option to decrease noise in sorter equipment, industries have opted to find other ways to apply noise control to their equipment. …

Accelerated Controller Tuning For Wind Turbines Under Multiple Hazards, Aly Mousaad Aly, Milad Rezaee

Faculty Publications

During their lifecycle, wind turbines can be subjected to multiple hazard loads, such as high-intensity wind, earthquake, wave, and mechanical unbalance. Excessive vibrations, due to these loads, can have detrimental effects on energy production, structural lifecycle, and the initial cost of wind turbines. Vibration control by various means, such as passive, active, and semi-active control systems provide crucial solutions to these issues. We developed a novel control theory that enables semi-active controller tuning under the complex structural behavior and inherent system nonlinearity. The proposed theory enables the evaluation of semi-active controllers’ performance of multi-degrees-of-freedom systems, without the need for time-consuming …

Project G.H.O.S.T., Matthew Morell, Austin Conrad, Zackeris Gordon, Conan Estes

Mechanical Engineering

Project G.H.O.S.T aimed to produce a model transmission with a control system for high performance/racing electric vehicles to utilize the full capability of the electric motor at higher speed applications. Current electric vehicles have a large amount of torque and use a fixed gear ratio that compromises between both high and low speeds with performance peaking around 65 miles per hour. A typical electric motor used in this application has approximately 1800 ft-lbs of torque up to 5,000 rpm. Past approximately 5,000 rpm, the torque rapidly drops off and so does the overall vehicle performance. Though transmissions exist that could …

Base Vibration Effects On Additive Manufactured Part Quality: A Study Of 3d Printing Onboard U.S. Navy Ships, Nick Jensen

Dissertations, Master's Theses and Master's Reports

The current landscape of manufacturing is evolving because of technology like additive manufacturing (AM). The mobility and compactness of AM are what make it desirable for many industry sectors. The U.S. Navy has shown interest in deploying AM on ships as it could alleviate their dependency on off-route docking to recharge supplies. However, the U.S. Navy's aspiration is currently hindered due to harsh ship-borne environments that degrade AM part quality.

This thesis focuses on vertical base vibration effects on AM part quality. An introduction is first given in Chapter 1 to familiarize the reader with the U.S. Navy's predicament. The …

Entertainment 721, Mark Hendricks, Noah John, Jadon Vanyo, Chelsea Payne

Williams Honors College, Honors Research Projects

The goal of this project was to design a luxury, aesthetically pleasing entertainment system with a TV lift mechanism that could be remote controlled. The design would also include a cooling cabinet for gaming systems, a remote locking system, and additional storage. Using a morphological chart and weighted decision matrix for each subsystem key features were determined to be included in the design. Several performance benchmarks were determined to accomplish the team’s design. Almost every benchmark was successful in the build of the first prototype. Several heat calculations and FEA analyses were performed on the system to ensure the success …

Defect Detection Using Dynamic Analysis For Additive Manufactured Metals, Gita Deonarain

Dissertations, Master's Theses and Master's Reports

Additive manufacturing (AM) has the ability to produce parts with complex geometries and internal features, however, for demanding applications such as the automotive and aerospace industries, it is crucial that the parts can meet the demanding functional and geometric requirements. Quality control for AM parts focuses on nondestructive methods of testing, but many of the current methods are expensive and time-consuming. The research presented in this report explores various methods of nondestructive evaluation (NDE) using dynamic analysis on stainless steel parts produced with selective laser melting (SLM). Methods include, but are not limited to, frequency response functions (FRF), impedance-based measurements, …

A Bibliometric Analysis Of Ultrasonic Vibration Assisted Turning, Govind S. Ghule, Sudarshan Sanap Prof. Dr.

Library Philosophy and Practice (e-journal)

Ultrasonic vibration-assisted turning (UVAT) is a new crossover in machining techniques which uses high frequency, low amplitude sound waves which are further superimposed on the cutting tool in traditional turning. This innovative technology is being utilized over the decades due to its conspicuous influence contrasted with traditional approach particularly in turning of hard-to-machine materials. This present paper analyses the past explores in the arena of ultrasonic vibration-assisted turning, by a far-reaching bibliometric investigation. The analysis is carried out by scrutinizing the studies through Science Direct and Scopus database to select the peer-reviewed papers. The advanced research tools like the word …

Dynamic Analysis And Fabrication Of A Bi-Stable Structure Designed For Mems Energy Harvesting Applications., Masoud Derakhshani

Electronic Theses and Dissertations

Thanks to the rapid growth in demand for power in remote locations, scientists’ attention has been drawn to vibration energy harvesting as an alternative to batteries. Over the past ten years, the energy harvesting community has focused on bistable structures as a means of broadening the working frequency range and, by extension, the effective efficiency of vibration-based power scavenging systems. In the current study, a new method is implemented to statically and dynamically analyze a bistable buckled, multi-component coupled structure designed specifically for low-frequency vibration energy harvesting systems in both macro and MEMS-scale sizes. Furthermore, several micro-fabrication steps using advanced …

Design Of Versatile Feedback Control System Components For Selective Laser Sintering, Thomas Chessman

University Scholar Projects

Selective laser sintering (SLS) is an additive manufacturing technique that involves using a laser to fuse powdered material together, layer by layer, in order to create a 3-D product. Despite its numerous benefits over traditional methods of manufacturing, including higher efficiency, versatility, and the ability to process many materials, selective laser sintering suffers from its propensity to generate structural errors during operation.

Feedback control has been shown to improve fabrication quality in other laser-based additive manufacturing techniques when implemented properly. Widespread exploration of applying feedback control in SLS might lead to significant performance improvements in this form of manufacturing.

This …

Dynamic Testing: An Experimental Approach To Defect Identification In Additive Manufactured Parts, Aimee Allen

Dissertations, Master's Theses and Master's Reports

Today’s additive manufacturing (AM) industry produces specialized parts at low volume or with complex geometries. Traditional testing methods are effective, but costly and time consuming to perform. The AM industry lacks an optimized testing method for identifying internal defects that occur in parts. The evaluation of multiple parts printed on the same build plate for internal defects using various nondestructive (dynamic) testing techniques is presented. From these experiments, perspective was gained on when and how dynamic testing can be used to find defects. Insight gained from these experiments can help the industry in future testing for internal defects.

Bibliometric Analysis Of Bearing Fault Detection Using Artificial Intelligence, Pooja Kamat, Rekha Sugandhi Dr.

Library Philosophy and Practice (e-journal)

The new industrial revolution called Industry 4.0 is proliferating at its peak. The time is no longer away when the human race is going to witness a huge paradigm shift. Intelligent machines empowered by Artificial Intelligence (AI)will take over the presence of human workers in the industrial manufacturing sector with the target of achieving 100% automation. With the emergence of cut-throat price competition in the product market, it has become equally important to manufacture goods at minimal costs and with the highest quality. Predicting the decrease in machinery efficiency at an earlier stage to accomplish this objective helps to reduce …

System Integration Of C-Arm Robotic Prototype Using Motion Capture Guidance For Accurate Repositioning, Alireza Yazdanshenas

Mechanical Engineering Theses

One of the important surgical tools in spinal surgery is the C-Arm X-ray System. The C-Arm is a large “C” shaped and manually maneuvered arm that provides surgeons and X-ray technicians the ability to take quick quality X-rays during surgery. Because of its five degrees of freedom, the C-Arm can be manually maneuvered around the patient to provide many angles and perspectives, ensuring surgical success.

This system works fine for most surgical procedures but falls short when the C-Arm must be moved out of the way for complicated surgical procedures.

The aim of this thesis is to develop an accurate …

Less-Than-Lethal Self Defense Device With An Acoustic Element, Anthony Taibi

KSU Journey Honors College Capstones and Theses

This creative capstone project involves the conception, design, and creation of a less-than-lethal self defense device with an integrated sound board to control the acoustic element. Theoretically, this device is capable of deterring potential threats without causing any serious harm or any long-term damage. When starting this project, I was very focused on sonic warfare, and how to harness the power of ultrasonic and infrasonic sound waves to subdue to target; however, I concluded that using resonant frequencies to deter a human being is too dangerous, expensive, and can have negative effects for the user of the device if used …

Ultrasonic Nondestructive Evaluation Of Metal Additive Manufacturing., Venkata Karthik Nadimpalli

Electronic Theses and Dissertations

Metal Additive Manufacturing (AM) is increasingly being used to make functional components. One of the barriers for AM components to become mainstream is the difficulty to certify them. AM components can have widely different properties based on process parameters. Improving an AM processes requires an understanding of process-structure-property correlations, which can be gathered in-situ and post-process through nondestructive and destructive methods. In this study, two metal AM processes were studied, the first is Ultrasonic Additive Manufacturing (UAM) and the second is Laser Powder Bed Fusion (L-PBF). The typical problems with UAM components are inter-layer and inter-track defects. To improve the …

Dyno-Mite Redesign, Brandon Joseph Miller, Daniel Robert Hoffman, Richard Demedici Young

Mechanical Engineering

The Cal Poly Mechanical Control Systems Laboratory currently employs an outdated device, known as the Motomatic, to teach students about various motor characteristics and control methods. These include open-loop vs. closed-loop control, speed vs. position control, and DC motor response curves. The current device does not function properly and produces unreliable data due to overwhelming non-linear effects such as stiction and shaft misalignment. Our team was tasked with designing a replacement device that retains many of the same educational goals as the original lab procedure, while also adding new educational goals pertaining to the device system dynamics. The new apparatus, …

Low Cost Metal Chip Separator, Alek Linquist, Kale Mckinney, Ryan Jones

Mechanical Engineering

We were tasked by Micro-Vu to design, build, and test a small-scale low-cost metal chip separator to operate on one of their 24/7 mills. The goal of the project was to separate the steel and aluminum chips coming off of the mill’s chip conveyor to end up with a bin of 99% pure aluminum by mass. To accomplish this goal we first brainstormed various possible ideas and performed small scale tests the best ones. After further review we determined the best solution to this problem was a design that involved a cycling magnetic backing that would pull steel out of …

Flag Raising Device, Josh Quintero

All Undergraduate Projects

The motivation for this project stems from a lifetime of boating with father Richard Jones. One problem that many people encounter, including Richard, was when towing someone behind a boat, is the difficulty with handling the warning flag. This flag is used to show other surrounding boats that someone has fallen into the water behind their boat. This warns other boats to stay far away from that area to keep safe from running over the swimmer. Although, when holding the flag in the boat, it can be hard to see at times. The boat driver, or other people standing in …

The University Of Akron Human Powered Vehicle Team, Maria E. Rizzo, Andrew J. Derhammer, Christopher M. Trowbridge, Timothy M. Nutt, Joseph R. Boyd, Jeremy W. Marcum, Jonathan E. Adams, Donald G. Haiss, Julia Wood, Brian D. Goshia, Scott T. Fagan, Joshua D. Everhard, Rebecca L. Slivka

Williams Honors College, Honors Research Projects

The University of Akron Human Powered Vehicle Team’s 2016 vehicle, Klokan, was designed, manufactured and tested with safety, reliability, performance and ease of use in mind. The vehicle is a fully faired tadpole trike with a lightweight aluminum frame constructed from 6061-T6 tubing having a total weight of 8.9 lbs. To complement the lightweight frame, the fairing is constructed from polycarbonate, PETG and carbon fiber strips which combine into a lightweight, easy to manufacture weather barrier and aerodynamic structure. Klokan was designed to be a safe and efficient mode of everyday transportation which ensures that riders are sufficiently protected by …