Mechanical Engineering Commons^™

Design And Validation Of A General Purpose Robotic Testing System For Musculoskeletal Applications, Lawrence D. Noble, Robb W. Colbrunn, Dong-Gil Lee, Antonie J. Van Den Bogert, Brian L. Davis

Mechanical Engineering Faculty Publications

Orthopaedic research on in vitro forces applied to bones, tendons, and ligaments during joint loading has been difficult to perform because of limitations with existing robotic simulators in applying full-physiological loading to the joint under investigation in real time. The objectives of the current work are as follows: (1) describe the design of a musculoskeletal simulator developed to support in vitro testing of cadaveric joint systems, (2) provide component and system-level validation results, and (3) demonstrate the simulator’s usefulness for specific applications of the foot-ankle complex and knee. The musculoskeletal simulator allows researchers to simulate a variety of loading conditions …

Development Of A Methodology For Numerical Simulation Of A D C Arc Discharge In A Liquid Dielectric, Christopher James Lewis

Theses and Dissertations

The majority of literature regarding the numerical simulation of arc discharges in gaseous environments has used a plasma physics approach. Virtually all simulations treat the discharge as an idealized gaseous plasma, which can be described by temperature, pressure, and electric field. This approach can work well if the media is a shielding gas such as Argon; however, the approach does not work well for processes such as underwater welding, EDM, and underwater discharges used to generate high purity particles. The reason these discharges do not have many extensive simulation efforts as described in the literature is because they occur in …

Preliminary Modelling Results For An Otto Cycle/Stirling Cycle Hybrid-Engine-Based Power Generation System, Barry Cullen, Jim Mcgovern, Michel Feidt, Stoian Petrescu

Conference Papers

This paper presents preliminary data and results for a system mathematical model for a proposed Otto Cycle / Stirling Cycle hybrid-engine-based power generation system. The system is a combined cycle system with the Stirling cycle machine operating as a bottoming cycle on the Otto cycle exhaust. The application considered is that of a stationary power generation scenario wherein the Stirling cycle engine operates as a waste heat recovery device on the exhaust stream of the Otto cycle engine. This paper is primarily concerned with the development of a model for a suitable Stirling cycle engine capable of running on the …

Geographic Variation In Potential Of Residential Solar Hot Water System Performance In The United States, Florida Solar Energy Center, Camilo Gil

FSEC Energy Research Center®

This paper describes an assessment of residential solar water heater performance around the continental United States. We performed annual simulations using an hourly simulation model (EGUSA) for 212 TMY3 weather locations around the nation. The annual simulations show how standard hot water energy use for electric and gas systems vary geographically (kWh and therms) as well as the potential energy savings from solar water heaters. A key finding is that the energy necessary for water heating varies by 2:1 around the U.S. with implications for solar water heating system design and sizing. Our results provide information on expected water heater …

A Real-Time, 3-D Musculoskeletal Model For Dynamic Simulation Of Arm Movements, Edward K. Chadwick, Dimitra Blana, Antonie J. Van Den Bogert, Robert F. Kirsch

Mechanical Engineering Faculty Publications

Neuroprostheses can be used to restore movement of the upper limb in individuals with high-level spinal cord injury. Development and evaluation of command and control schemes for such devices typically require real-time, ldquopatient-in-the-looprdquo experimentation. A real-time, 3-D, musculoskeletal model of the upper limb has been developed for use in a simulation environment to allow such testing to be carried out noninvasively. The model provides real-time feedback of human arm dynamics that can be displayed to the user in a virtual reality environment. The model has a 3-DOF glenohumeral joint as well as elbow flexion/extension and pronation/supination and contains 22 muscles …

The Relationships Between Muscle, External, Internal And Joint Mechanical Work During Normal Walking, Kotaro Sasaki, Richard R. Neptune, Steven A. Kautz

Mechanical and Biomedical Engineering Faculty Publications and Presentations

Muscle mechanical work is an important biomechanical quantity in human movement analyses and has been estimated using different quantities including external, internal and joint work. The goal of this study was to investigate the relationships between these traditionally used estimates of mechanical work in human walking and to assess whether they can be used as accurate estimates of musculotendon and/or muscle fiber work. A muscle-actuated forward dynamics walking simulation was generated to quantify each of the mechanical work measures. Total joint work (i.e. the time integral of absolute joint power over a full gait cycle) was found to underestimate total …

Simulation Of A Tubular Solid Oxide Fuel Cell Stack Operating On Biomass Syn-Gas Using Aspen Plus, Wayne Doherty, Anthony Reynolds, David Kennedy

Articles

A tubular solid oxide fuel cell (SOFC) stack is modelled and its operation on biomass syn-gas is investigated. The objective of this work is to develop a computer simulation model of a biomass gasification-SOFC (BG-SOFC) system capable of predicting performance under various operating conditions and using diverse fuels. The stack is modelled using Aspen Plus and considers ohmic, activation and concentration losses. It is validated against published data for operation on natural gas. Operating parameters such as fuel and air utilisation factor (U_f and U_a), current density (j) and steam to carbon ratio ( …

Simulation Of A Circulating Fluidised Bed Biomass Gasifier Using Aspen Plus: A Performance Analysis, Wayne Doherty, Anthony Reynolds, David Kennedy

Conference Papers

In the near future biomass gasification is likely to play an important role in energy production and conversion. Its application has great potential in the context of climate change mitigation, increasing efficiency and energy security. Atmospheric circulating fluidised bed (CFB) technology was selected for the current study. An original computer simulation model of a CFB biomass gasifier was developed using ASPEN Plus (Advanced System for Process ENgineering Plus). It is based on Gibbs free energy minimisation and the restricted equilibrium method was used to calibrate it against experimental data. This was achieved by specifying the temperature approach for the gasification …

Simulation And Fabrication Of Three Novel Micromechanical Sensors, Yanqing Lu

Doctoral Dissertations

This work focuses on the simulation, fabrication and characterization of novel microdevices for chemical and biological sensors for improved sensitivity, enhanced performance and applicability. Specifically, microbridge and microcoil sensors have been fabricated via advanced microfabrication technologies. Due to the potential application in chemical and biological sensing, the growth of gold and platinum nanowires during an electrolysis process have also been investigated.

A microbridge can be considered as the head-to-head fusion of two cantilevers and the middle of the bridge would deform in a way similar to a microcantilever. The microbridge sensing device is more stable than the microcantilever, especially in …

Modeling And Simulation Of A Microturbine Generator To Be Coupled With A Molten Carbonate Fuel Cell For Distributed Generation, Karleine M. Justice

Browse all Theses and Dissertations

Distributed generation is desired when the individual energy requirements ranging from 25-75 kW of office buildings, restaurants, hospitals and apartments can not be met by the current electric utility grid. Microturbine generators as stand alone power generation systems have been designed to meet these requirements. For power requirements up to 50 MW, hybrid fuel cell systems offer higher efficiency and lower levels of pollutant emissions with more advanced fuel energy savings than non-hybrid systems. The objective of this project is to develop a simulation of a microturbine generator as a stand alone power generation system to validate a microturbine generator …

Comparison Of Solar Hot Water Systems Simulated In Energygauge Usa And Trnsys 15, Florida Solar Energy Center, Michael Anello

FSEC Energy Research Center®

This document is meant to serve as a detailed summary of the comparison between the simulation methods of EnergyGauge USA and TRNSYS (version 15) relating to solar hot water systems. The initial motivation behind this comparison was to verify that the f-chart model created for EnergyGauge's solar hot water calculations was reporting the correct results. To this end, models of three systems were created in TRNSYS in order to serve as a baseline for the EnergyGauge results. The three systems modeled were: Liquid-active closed loop (LACL), Liquid-active open loop (LAOL), Integrated collector storage (ICS). This document will detail each of …

Energy Efficient Renovations Of Storm Damaged Residences - Florida Case Studies, Florida Solar Energy Center, Neil Moyer

FSEC Energy Research Center®

Storm-damaged homes offer the opportunity for repairs that reduce energy use, improve comfort and enhance resistance to future storms. Case studies of four Florida homes damaged in the summer of 2004 were documented to show the costs and benefits of various retrofit strategies. All four homes required roof replacement and each took advantage of roof cladding with higher reflectance than the original, a proven means of reducing cooling energy use. Two of the case studies included improvements to attic insulation, tightening of the envelope and/or duct system and improved efficiency equipment and lighting. Energy savings attributable to storm repairs were …

Analysis Of Technical Energy Losses By Using Simulation, Betrianis Betrianis, Randite Herawan

Makara Journal of Technology

Model is a representation of a system. Through model, it can be easier to forecast and control the changing of each element system. Electricity distribution is also a system. Losses are general problem that exist in a distribution network system. But with the right methods, specifically technical energy losses can be reduced in order to increase the efficiency. By making model of the distribution network, the value of technical energy losses in the whole network as well as in every line can be observed. Simulation can also be used to see all losses reduction alternatives. By comparing results from each …

Technical Support For Development Of An Attic Simulation Model For The California Energy Commission, Florida Solar Energy Center, Danny Parker

FSEC Energy Research Center®

The California Energy Commission (CEC) is developing a new attic simulation model for assessing residential energy performance within its Title 24 residential compliance methodology. Within this project, we are providing technical support to assist Bruce Wilcox and CEC in development of the model based on Florida Solar Energy Center (FSEC) experience with similar models. We assisted the effort by using data from FSEC instrumented facilities to help verify the eventual simulation. We also outlined critical issues for modeling with the development of the simulation. Given the importance of attic ventilation, we are also conducting new studies of varied ventilation rates …

Integrating Value Stream Mapping And Simulation, Michelle E. Scullin

Theses and Dissertations

An important principle in Lean manufacturing, value stream mapping (VSM) can be helpful in understanding how process flow and information flow affect each other. A VSM is a static picture of a process that allows the user to see where value is added into the value stream. Simulation is used to evaluate the behavioral issues of processes. In a manufacturing realm this means simulation shows how each operation affects other operations so determinations can be made about where bottlenecks or other problems exist in the process. Theoretically, the integration of VSM and Simulation can aide in process improvement by showing …

Finite Element Analysis Of Covered Microstents, Linxia Gu, Swadeshmukul Santra, Robert A. Mericle, Ashok V. Kumar

Department of Mechanical and Materials Engineering: Faculty Publications

Currently available neuroendovascular devices are inadequate for effective treatment of many wide-necked or fusiform intracranial aneurysms and intracranial carotid-cavernous fistulae (CCF). Placing a covered microstent across the intracranial aneurysm neck and CCF rent could restore normal vessel morphology by preventing blood flow into the aneurysm lumen or CCF rent. To fabricate covered microstents, our research group has developed highly flexible ultra thin (~150 μm) silicone coverings and elastomerically captured them onto commercially available metal stents without stitching. Preliminary in vivo studies were conducted by placing these covered microstents in the common carotid artery of rabbits. The feasibility of using covered …

Evaporating Cross Flow Spray Jets In Gas-Solid Circulating Fluidized Bed, Tong Hoon Lee

Dissertations

Three-phase flow of solid-gas suspension with liquid spray is found in many industrial applications, including fluidized catalytic cracking in petroleum refinery process, and wet scrubbing process. This dissertation study is aimed to understand the gas-solid-liquid three-phase flow structure, phase interactions and transport in a gas-solid circulating fluidized bed where an evaporating cross-flow liquid spray jet from a rectangular nozzle with a fan angle is injected. The investigation is based on both numerical and experimental approaches. The numerical study is for detailed field descriptions of the flow structure, phase interaction and distributions whereas the experimental study is for simulation validations. The …

Development And Application Of A New Modeling Technique For Production Control Schemes In Manufacturing Systems, Bashar Hafez Sader

Theses and Dissertations

This dissertation presents dynamic system models of continuous manufacturing systems based on analogies with electrical systems. The developed modeling technique has the capability to explicitly specify production control schemes including control points, material and information flow paths, and logical operations. The model provides standard graphical representations and governing equations to describe both the steady state and transient responses of continuous manufacturing systems. For deterministic systems, these equations can be solved to get closed-form solutions. For stochastic systems, numerical solutions can be obtained for any probabilistic distribution. The electrical analogs provide an excellent tool to model control signals and logical operations. …

A Tool Wear Comparative Study In Turning Versus Computer Simulation In 1018 Steel, Woodrow D. Miner

Theses and Dissertations

The material removal process uses cutting tools in order to produce the desired shape of the workpiece. Tool wear has been a problem for cutting tools, since cutting tools wear and break. Research has been accomplished in the tool wear field for tool life and more recently tool wear. The computer generation has created a method to simulate the material removal process. These computer simulations model the cutting tool reaction with the workpiece. Many of the simulation models use finite element analysis to calculate the reaction of the cutting tool. Different finite element models are being used throughout the world …

Experimental And Numerical Study Of Feeding Channel In Proton Exchange Membrane Fuel Cell, Abul Bashar Mahmud Hasan

LSU Master's Theses

The performance of a Proton Exchange Membrane Fuel Cell (PEMFC) using different feeding configurations has been studied, with a focus on the water flooding due to electrochemical reaction. Feeding channel or Bipolar plate in Proton Exchange Fuel Cell is a dominating part. As feeding channel keeps direct contact with the gas diffusion layer, it helps efficiently supplying fuel and air into the gas diffusion layer for efficient production of electricity. Experimental data have been taken at hydrogen flow rates of 20,40,60,80,100 sccm for various bipolar plate arrangements. Three bipolar plates, namely serpentine, straight channel and interdigitated designs, were arranged in …

A Finite Element Simulation Of Temperature And Material Flow In Fricton Stir Welding, Mark J. Lasley

Theses and Dissertations

The purpose of this research was to use the Transvalor S.A. product, Forge3, to develop a finite element simulation of the friction stir welding process that improves the predictability of temperature evolution and material flow within the plunge portion of the process. Previous modeling created more heating within the billet than experimental results, probably due to the simplification of the simulation with adiabatic boundary conditions. More realistic tooling temperatures were included in this model as these affect heat evolution which is a determining factor in microcrystalline growth. These results were validated by experimental efforts using a billet and tooling instrumented …

Pre-Impact Lower Extremity Posture And Brake Pedal Force Predict Foot And Ankle Forces During An Automobile Collision, Elizabeth C. Hardin, Anne Su, Antonie J. Van Den Bogert

Mechanical Engineering Faculty Publications

Background: The purpose of this study was to determine how a driver’s foot and ankle forces during a frontal vehicle collision depend on initial lower extremity posture and brake pedal force. Method of Approach: A 2D musculoskeletal model with seven segments and six right-side muscle groups was used. A simulation of a three-second braking task found 3647 sets of muscle activation levels that resulted in stable braking postures with realistic pedal force. These activation patterns were then used in impact simulations where vehicle deceleration was applied and driver movements and foot and ankle forces were simulated. Peak rearfoot ground reaction …

The Benefit Of Using Simulation To Improve The Implementation Of Lean Manufacturing Case Study: Quick Changeovers To Allow Level Loading Of The Assembly Line, Jack J. Mcclellan

Theses and Dissertations

In today's competitive manufacturing environment, companies are constantly looking for ways to improve. Because of this, many companies are striving to become "lean" by implementing lean manufacturing, which is a difficult process. To aid in the implementation of lean manufacturing, simulation was used to reduce the trial-and-error period of lean manufacturing and find to optimum approach to implement the lean manufacturing principle. In this research, a case study of implementing level loading of the production schedule for BullFrog International, L.C. will be examined. To make it possible to implement level loading, the thermo-former machine at the beginning of the operations …

Foot And Ankle Forces During An Automobile Collision: The Influence Of Muscles, Elizabeth C. Hardin, Anne Su, Antonie J. Van Den Bogert

Mechanical Engineering Faculty Publications

Muscles have a potentially important effect on lower extremity injuries during an automobile collision. Computational modeling can be a powerful tool to predict these effects and develop protective interventions. Our purpose was to determine how muscles influence peak foot and ankle forces during an automobile collision. A 2-D bilateral musculoskeletal model was constructed with seven segments. Six muscle groups were included in the right lower extremity, each represented by a Hill muscle model. Vehicle deceleration data were applied as input and the resulting movements were simulated. Three models were evaluated: no muscles (NM), minimal muscle activation at a brake pedal …

Migration Of An Intruder Particle In A Boundary Driven Shear Flow, Jian Liu

Dissertations

This study reports on three-dimensional, discrete element simulations of a single large spherical intruder in a Couette shear flow composed of uniform sized particles. The simulation results are useful in providing a numerical reproduction of the experiments for size segregation and mixing. This in turn has a major importance in many industries which are concerned with handling of particles and powders, such as pharmaceutical manufacturing, agriculture, chemical and mineral processing.

Discrete element simulations are carried out using the "soft sphere" model of Walton, et. al., which provides a method for obtaining the information at a macroscopic level from multi-body collisions …

Mesoscopic Simulation Of Abnormal Grain Growth, Rakesh Kumar Behera

LSU Master's Theses

Grain growth is the process that takes place during annealing of polycrystalline materials; its major feature is a systematic increase in grain size. Two different types of grain growth can be distinguished: the normal and abnormal grain growth. During normal grain growth, the microstructure exhibits a uniform increase in grain size with time and the grain size distribution follows the log-normal distribution with the grain sizes ranging from 0 - 2.2 times the average grain size (R). On the contrary, when the abnormal grain growth is the dominant mechanism, there are certain grains (abnormal grains) in the microstructure that grow …

Simulation Of The Communication Process In A Pin Mill, Ambrose J. M. Itika

Tanzania Journal of Engineering and Technology (TJET)

Prediction of the performance of comminution equipment by mathematical models and simulation poses a great challenge to the chemical engineer. This paper describes the simulation of grinding results obtained using an impact mill. Single particle results have been used to generate breakage and selection coefficients that were used for the evaluation of the model. Results have shown that simulation model is in good agreement with the experimental data obtained at a circumferential speed above 60 m/s. At lower speeds, the models shows only partial agreement in the middle particle size ranges. The application of the model is therefore limited for …

Field Testing And Computer Modeling To Characterize The Energy Impacts Of Air Handler Leakage, Florida Solar Energy Center, James Cummings

FSEC Energy Research Center®

In order to determine the impact of air handler location upon heating and cooling energy use, the amount of air leakage which occurs in the air handler cabinet needs to be known. Also, the leakage which occurs at the connections between the air handler cabinet and the return and supply plenums needs to be known as well because these connection leaks would also be located in the attic or any other location.

In order to assess this leakage, testing was performed on a total of 69 air conditioning systems. Thirty systems were tested in the year 2001 under funding from …

An Integrated Approach To Simulation And Activity-Based Costing For Evaluating Alternative Manufacturing Cell Designs, Robert Williams, Paul Savory, Rodney Rasmussen

Department of Industrial and Management Systems Engineering: Faculty Publications

One effective technique for improving manufacturing efficiency involves the application of group technology part families and manufacturing cells. Selection of the best or optimum configuration of the manufacturing cell relies on the experience and judgment of the cell designer. This paper describes how activity-based costing (ABC) concepts can be integrated into a discrete-event simulation model and be used to evaluate manufacturing cell configurations. The output of the combined ABC simulation model provides a detailed “Bill of Activity” which allows the cell designer to consider costs as a critical factor in the cell design problem. Alternative cell configurations studied in this …

A Mathematical Model And Simulation Of Natural Circulation Loop Thermalhydraulics, Nihad E. Daidzic

Aviation Department Publications

In this work, a simple, nonlinear, seventh-order mathematical model with lumped parameter analysis of the thermalhydraulic processes in a natural circulation steam boiler loop is presented. Digital simulation has been performed in order to predict open loop transients in severe accidental situations. Parts of the circulation loop such as the steam drum, downcomer, and riser were modelled separately on the basis of the integral balance equations. The two-phase flow in the steam drum and in the riser was modelled with the aid of a homogeneous-equilibrium, two-phase flow model. Special care was taken to ensure the stability of the numerical scheme, …