Mechanical Engineering Commons^™

The Mechanical Development For An Autonomous Forest Service Robot, James P. Walker

Honors College Theses

Georgia’s forests are under threat from numerous invasive species of plant, both herbaceous and woody. A primary factor in the invasive potential of any given non-native plant is the lack of natural predators and rapid reseed and regrowth cycles. To combat invasive plants, this thesis proposes an artificial, robotic predator to provide a means of controlling invasive species. Although autonomous robots are currently being developed for similar agricultural purposes, none have emerged for forestry related tasks, such as proposed in this work. The chassis, inspired by rocker bogie and similar suspension systems, has been redesigned to have eight wheels, to …

Trunk Velocity-Dependent Light Touch Reduces Postural Sway During Standing, Anirudh Saini, Devin Michael Burns, Darian Emmett, Yun Seong Song

Psychological Science Faculty Research & Creative Works

Light Touch (LT) has been shown to reduce postural sway in a wide range of populations. While LT is believed to provide additional sensory information for balance modulation, the nature of this information and its specific effect on balance are yet unclear. In order to better understand LT and to potentially harness its advantages for a practical balance aid, we investigated the effect of LT as provided by a haptic robot. Postural sway during standing balance was reduced when the LT force (~ 1 N) applied to the high back area was dependent on the trunk velocity. Additional information on …

Generic Project Plan For A Mobile Robotics System, Jay Anilkumar Joshi

Masters Theses & Specialist Projects

This thesis discussed the mobile land robots for the robotic competitions. The topics discussed in this thesis are robotic systems, mobile land robots, robot competitions, and example of robot designs. Question-answer sections are added to help understand the requirements to build the robot. Examples include three different teams who participated in different robotic competitions to provide a context for robotic competitions. The thesis was divided into the five chapters. The first and second chapters explained the different kind of robotics systems, and opportunities. The focus of the information was the mobile land robots, which was explained under the third chapter, …

Foot-Controlled Supernumerary Robotic Arm: Foot Interfaces And Human Abilities, Brandon William Rudolph

Graduate Theses - Mechanical Engineering

A supernumerary robotic limb (SRL) is a robotic limb that can act as an extra arm or leg for a human user. An unsolved issue with SRLs is how to operate them well. One possibility is to control an SRL with the foot, which offers the benefit of a third arm because the user’s arms remain unoccupied. While hand interfaces are common, foot interfaces are not well understood. Developing a good foot interface is challenging because of differences between feet and hands, such as the larger inertia of the leg. This thesis presents work to determine some design principles for …

System Integration Of C-Arm Robotic Prototype Using Motion Capture Guidance For Accurate Repositioning, Alireza Yazdanshenas

Mechanical Engineering Theses

One of the important surgical tools in spinal surgery is the C-Arm X-ray System. The C-Arm is a large “C” shaped and manually maneuvered arm that provides surgeons and X-ray technicians the ability to take quick quality X-rays during surgery. Because of its five degrees of freedom, the C-Arm can be manually maneuvered around the patient to provide many angles and perspectives, ensuring surgical success.

This system works fine for most surgical procedures but falls short when the C-Arm must be moved out of the way for complicated surgical procedures.

The aim of this thesis is to develop an accurate …

Design Of A Canine Inspired Quadruped Robot As A Platform For Synthetic Neural Network Control, Cody Warren Scharzenberger

Dissertations and Theses

Legged locomotion is a feat ubiquitous throughout the animal kingdom, but modern robots still fall far short of similar achievements. This paper presents the design of a canine-inspired quadruped robot named DoggyDeux as a platform for synthetic neural network (SNN) research that may be one avenue for robots to attain animal-like agility and adaptability. DoggyDeux features a fully 3D printed frame, 24 braided pneumatic actuators (BPAs) that drive four 3-DOF limbs in antagonistic extensor-flexor pairs, and an electrical system that allows it to respond to commands from a SNN comprised of central pattern generators (CPGs). Compared to the previous version …

A Low-Cost Experimental Testbed For Multi-Agent System Coordination Control, Victor Fernandez-Kim

LSU Master's Theses

A multi-agent system can be defined as a coordinated network of mobile, physical agents that execute complex tasks beyond their individual capabilities. Observations of biological multi-agent systems in nature reveal that these ``super-organisms” accomplish large scale tasks by leveraging the inherent advantages of a coordinated group. With this in mind, such systems have the potential to positively impact a wide variety of engineering applications (e.g. surveillance, self-driving cars, and mobile sensor networks). The current state of research in the area of multi-agent systems is quickly evolving from the theoretical development of coordination control algorithms and their computer simulations to experimental …

Motor Control Systems Analysis, Design, And Optimization Strategies For A Lightweight Excavation Robot, Austin Jerold Crawford

Graduate Theses and Dissertations

This thesis entails motor control system analysis, design, and optimization for the University of Arkansas NASA Robotic Mining Competition robot. The open-loop system is to be modeled and simulated in order to achieve a desired rapid, yet smooth response to a change in input. The initial goal of this work is to find a repeatable, generalized step-by-step process that can be used to tune the gains of a PID controller for multiple different operating points. Then, sensors are to be modeled onto the robot within a feedback loop to develop an error signal and to make the control system self-corrective …

Design Of A Scara Based Mobile 3d Printing Platform, Zachary Hyden

Mechanical Engineering Undergraduate Honors Theses

Currently 3D printers rely heavily on people to run them, there is no automatic way to start a new print after one has finished. On top of this 3D printers are limited in the area they can print on. Even though the additive manufacturing market is rapidly growing and is increasingly being used in product manufacturing there has yet to be a solution to this problem. This research proposes using mobile 3D printing robots to solve both of these issues. The proposed prototype utilizes a Selective Compliance Assembly Robot Arm (SCARA) based robot capable of cooperatively manufacturing parts. This allows …

2019 Ieee Southeastcon Hardware Competition: A Systems Engineering Approach, Emily Sage

Mahurin Honors College Capstone Experience/Thesis Projects

The Institute for Electrical and Electronics Engineers (IEEE) Huntsville section invites college students to participate in their annual SoutheastCon Conference. Western Kentucky University sends a team of engineering students to the hardware competition, an opportunity for students to design and build autonomous robots. The 2019 hardware competition called for students to develop a robot that could collect and sort debris by color. This thesis outlines the project lifecycle of the WKU 2019 SoutheastCon robot with an emphasis on implemented systems engineering tools and techniques. Systems Engineering is an interdisciplinary approach to project management that focuses on treating the overall project …

Design, Control, And Optimization Of Robots With Advanced Energy Regenerative Drive Systems, Poya Khalaf

ETD Archive

We investigate the control and optimization of robots with ultracapacitor based regenerative drive systems. A subset of the robot joints are conventional, in the sense that external power is used for actuation. Other joints are energetically self-contained passive systems that use ultracapacitors for energy storage. An electrical interconnection known as the star configuration is considered for the regenerative drives that allows for direct electric energy redistribution among joints, and enables higher energy utilization efficiencies. A semi-active virtual control strategy is used to achieve control objectives. We find closed-form expressions for the optimal robot and actuator parameters (link lengths, gear ratios, …

Robust Impedance Control Of A Four Degree Of Freedom Exercise Robot, Santino Joseph Bianco

ETD Archive

The CSU 4OptimX exercise robot provides a platform for future research into advanced exercise and rehabilitation. The robot and its control system will autonomously modify reference trajectories and impedances on the basis of an optimization criterion and physiological feedback. To achieve this goal, a robust impedance control system with trajectory tracking must be implemented as the foundational control scheme. Two control laws will be compared, sliding mode and H-infinity control. The above robust control laws are combined with underlying impedance control laws to overcome uncertain plant model parameters and disturbance anomalies affecting the input signal. The sliding mode control law …

Analysis And Control Of Fiber-Reinforced Elastomeric Enclosures (Frees), Soheil Habibian

Master’s Theses

While rigid robots are extensively used in various applications, they are limited in the tasks they can perform and can be unsafe in close human-robot interactions. Soft robots on the other hand surpass the capabilities of rigid robots in several ways, such as compatibility with the work environments, degrees of freedom, manufacturing costs, and safe interactions with the environment. This thesis studies the behavior of Fiber-Reinforced Elastomeric Enclosures (FREEs) as a particular type of soft pneumatic actuator that can be used in soft manipulators. A dynamic lumped-parameter model is created to simulate the motion of a single FREE under various …

Remotely Controlled Industrial Robotic Arm And Simulation Of Automated Thermal Furnace, Prince Mehandi Ratta

Dissertations, Master's Theses and Master's Reports

The right execution of controllers ensures the correct analysis of information, generating efficient results and better optimizing the system. In this report, two controllers were designed. Firstly, a remotely controlled robotic arm, since there are no such type commercially available controllers. Moreover, robotic platforms are costly, so students and researchers are often unable to learn the concepts of programming industrial robots. This project makes a non-destructive, remotely-controlled robotic arm to better teach students and researchers about programming and control of robotic arms. Secondly, simulation of an automated thermal furnace for ArcelorMittal on SIMULINK, which is used for the annealing process …

A Scalable, Chunk-Based Slicer For Cooperative 3d Printing, Jace J. Mcpherson

Computer Science and Computer Engineering Undergraduate Honors Theses

Cooperative 3D printing is an emerging technology that aims to increase the 3D printing speed and to overcome the size limit of the printable object by having multiple mobile 3D printers (printhead-carrying mobile robots) work together on a single print job on a factory floor. It differs from traditional layer-by-layer 3D printing due to requiring multiple mobile printers to work simultaneously without interfering with each other. Therefore, a new approach for slicing a digital model and generating commands for the mobile printers is needed, which has not been discussed in literature before. We propose a chunk-by-chunk based slicer that divides …

Design Of Parallel Robot For Dental Articulation And Its Optimization, Abulimiti Delimulati

Department of Mechanical and Materials Engineering: Dissertations, Theses, and Student Research

A dental articulator is a mechanical device used to simulate the relative position and motion between the upper and lower jaw when constructing and testing dental prostheses. Typically, it can be adjusted to approximate patient-specific jaw kinematics in order to analogue the static relationship and specific motions of a patient’s mandible to maxilla. However, the use of dental articulators is essentially a trial-and-error method in order to fine-tune fit and function of a dental prosthesis. Some of the most advanced current dental articulators can reproduce the position and the motion passively; furthermore, dentists need special training for measuring patients’ maxillofacial …

Control Design And Implementation Of An Active Transtibial Prosthesis, Joseph Klein

Master's Theses (2009 -)

Prior work at Marquette University developed the Marquette Prosthesis, an active transtibial prosthesis that utilized a torsional spring and a four-bar mechanism. The controls for the Marquette Prosthesis implemented a finite state control algorithm to determine the state of gait of the amputee along with two lower level controllers, a PI moment controller to control the moment during stance and a PID position controller to control the position during stance. The Marquette Prosthesis was successful in mimicking the gait profile presented by Winter. However, after completing human subject testing, the Marquette Prosthesis was insufficient in trying to match the gait …

Design Optimization And Control Of A Fully Actuated Hexrotor Uav For Use In Aerial Manipulation Applications, Jameson Yau Sung Lee

UNLV Theses, Dissertations, Professional Papers, and Capstones

This work addresses the issue of controller complexity in the application of a special class of multirotor in aerial manipulation tasks. Much of the current research concerning aerial manipulation involves the modeling and control of highly coupled multirotor and manipulator systems. This is a consequence of the platform’s under-actuation condition. To accommodate the rejection of arbitrary wrench disturbances brought about by the environment, multirotor must perform deliberate attitude tracking to affect forward and lateral maneuvers mid-flight. The manipulator end-effector tracking is highly affected by this, thus, their performance in general aerial manipulation is limited. To address these limitations, a special …

Anthropomorphically Inspired Design Of A Tendon-Driven Robotic Prosthesis For Hand Impairments, Manali Bapurao Bhadugale

Mechanical & Aerospace Engineering Theses & Dissertations

This thesis presents the design of a robotic prosthesis, which mimics the morphology of a human hand. The primary goal of this work is to develop a systematic methodology that allows a custom-build of the prosthesis to match the specific requirements of a person with hand impairments. Two principal research questions are addressed toward this goal: 1) How do we cater to the large variation in the distribution of overall hand-sizes in the human population? 2) How closely do we mimic the complex morphological aspects of a biological hand in order to maximize the anthropomorphism (human-like appearance) of the robotic …

Robotic Mining Digging Core, John Stefan, Ryan Weir

Williams Honors College, Honors Research Projects

The purpose of this design project is to design a digging core for a lunar robot that will collect large amounts of material buried beneath the surface of Mars so one day, astronauts can use those resources. This lunar robot will be competing in the NASA Robotic Mining Competition, where teams from universities around the country display and test their designs. This design must adhere to a newly implemented rule which states that the amount of gravel a robot collects will determine the team score. The layer of gravel is located underneath a layer of Regolith, which simulates the surface …

Real-Time Minimum Jerk Optimal Trajectory Synthesis And Tracking For Ground Vehicle Applications, Naga Venkata Murali Veerapaneni

Mechanical and Aerospace Engineering Theses - Archive

Research on wheeled mobile robots has been an active research field for several decades with focus on the problems of stability, maneuverability and control. The trajectory generation for wheeled mobile robots is usually handled by considering a smooth function satisfying the boundary conditions. Even though this problem is well posed for several function classes, the real issue occurs in generating a feasible trajectory for the robot which takes into account the constraints of the system. Another problem from the control system perspective is, whether the derived controller is stable for the entire trajectory span to track the given trajectory. The …

Poly Spotlight Control, Ryan P. O'Neill, C. Oleg Frandle, Anthony T. Lombardi

Mechanical Engineering

When this project began, The Cambria Center for the Arts Theater used a manually-operated spotlight. The sound created by the fans, along with the sheer size of the spotlight, required that it be housed in an attic room above the theater and shined through a closed window. This trapped a lot of heat in the room and involved some risk with climbing into and out of the attic room. This project sought to remedy those issues by mounting a pair of newer LED spotlights inside the theater. Doing this required a method for remotely controlling and actuating the angular position …

Finite Element Analysis And Biological Growth Realization Using Robot Swarms, Cody W. Dorbin, Adrian Buganza-Tepole

The Summer Undergraduate Research Fellowship (SURF) Symposium

Our understanding of growth and remodeling of biological systems has increased in the past two decades; however, this knowledge has not yet been used in human-designed systems or engineering applications. This project studies designing and building a network of robots that mimics the biological behavior of growth driven by cell-cell communication and control networks. The objective of this research is to harness the principles that govern tissue adaptation and morphogenesis, where peer-to-peer local communication determines global properties, to create human-made engineering systems with life-like capabilities. We used Arduino microcontrollers to control an individual robot in an expandable 3d-printed cuboid shell. …

Flexible-Continuum Robot For Bladder Tissue Diagnostics, Samson Abimbola Adejokun

Mechanical and Aerospace Engineering Theses - Archive

The aim of this thesis is to investigate and develop a robotic system capable of a transurethral palpation of any targeted area on the bladder interior wall tissue to determine the biomechanical properties of the tissue considering the urinary tract geometric constraints and to demonstrate the motion kinematics of such robot to achieve a desired robot pose normal to any localized region throughout the bladder workspace. Current technologies have, to varied degree of success, provide approximate, global diagnostics information to bladder tissue elasticity. However, no direct access qualitative methods to measure the bladder tissue properties are known. For this reason, …

Wheelieking Trainer Project Report, Harold Hall Iii, Nathaniel Fox, Thomas Niemisto

Biomedical Engineering

In this report we will detail the design and implementation process of the WheelieKing Trainer project, a device that helps people learn how to do wheelies on a bicycle by preventing backward falls. Formal project requirements are specified, followed by the ideation and iteration process to meet those requirements. The components and methods used to create the device are described in detail. The results of the development process and usage test results of the device are included. Appendices at the end of this report include references, supporting analyses, and project management and timeline details.

A Handy Underwater Solution, Benjamin Murdoch, Matt Ricks, Ales Ball, Jacob Olson, Ethan Durrant, Connor Monson, Lars Watts, Mark Killpack

Journal of Undergraduate Research

Hod Lipson once asked an audience at TED, “Where are the robots?” We’ve been waiting for them a long time now and modern robotics still hasn’t caught up with our hopes and dreams. Through our research we hope to address one of the major topics in robotics: movement (or kinematics), and use this moment of exploration to build a new low cost robotic hand capable of use within the exciting realm of aquatics.

Safer Sweep Auger Operation Using Robotics, Nathan A. Wulf

Department of Mechanical and Materials Engineering: Dissertations, Theses, and Student Research

This thesis presents a remotely controlled robotic solution for those who must sometimes enter agriculturally confined spaces in attempts to assist with grain bin cleanout, particularly by manipulating the sweep auger. In 2015 alone, there were at least 47 documented incidents that occurred in agriculturally confined spaces, of which more than half were fatal. While there have been several advancements in the quality and effectiveness of sweep augers, there have been very few that offer the safety and adaptability of the robotic solution proposed. This robotic solution is a four-wheeled, skid-steering style robot with camera and lighting attachments that allow …

Design And Control Of A Powered Rowing Machine With Programmable Impedance, Jose Humberto De La Casas Zolezzi

ETD Archive

Due to the rise of obesity, diabetes and cardiovascular disease, research in human performance and physical activity has received increased attention. Rowing machines are used for performance improvements through concentric exercises, however a combination of concentric and eccentric actions is known to improve the effectiveness of training. In this work, a conventional rowing machine was modified to include an electric motor and a robust impedance control system, enabling programmable impedance with concentric and eccentric capabilities. Eccentric exercises are known to contribute significantly to the efficacy of training and to diminish the detrimental effects of humans operating in microgravity for long …

A Visual Velocity Impedance Controller, Victor Nevarez

Mechanical Engineering ETDs

Successful object insertion systems allow the object to translate and rotate to accommodate contact forces. Compliant controllers are used in robotics to provide this accommodation. The impedance compliant controller is one of the more researched and well known compliant controllers used for assembly. The velocity filtered visual impedance controller is introduced as a compliant controller to improve upon the impedance controller. The velocity filtered impedance controller introduces a filter of the velocity impedance and a gain from the stiffness. The velocity impedance controller was found to be more stable over larger ranges of stiffness values than the position based impedance …

Mesh Addition Based On The Depth Image (Mabdi), Lucas E. Chavez

Mechanical Engineering ETDs

Many robotic applications utilize a detailed map of the world and the algorithm used to produce such a map must take into consideration real-world constraints such as computational and memory costs. Traditional mesh-based environmental mapping algorithms receive data from the sensor, create a mesh surface from the data, and then append the surface to a growing global mesh. These algorithms do not provide a computationally efficient mechanism for reducing redundancies in the global mesh. MABDI is able to leverage the knowledge contained in the global mesh to find the difference between what we expect our sensor to see and what …