Mechanical Engineering Commons^™

Optimization Pump As Turbine Coupled To A Self-Excited Induction Generator Using Multi-Objective Genetic Algorithm, Emanuel J. Nyirenda

Tanzania Journal of Engineering and Technology (TJET)

As a way of accelerating the deployment of affordable and clean renewable energy generation technologies, applying a pump working as a turbine coupled to a self-excited induction generator is gaining popularity in various areas including energy recovery and micro hydro systems. However, it is currently challenging to predict the performance of the PAT-SEIG system and there is no agreed-upon rule on the selection of the appropriate system to be installed at a particular site. This paper has presented multi-objective optimization to select the best operating point of the PAT-SEIG system. The results show that the peak efficiencies for the PAT …

Integrated Analysis Of Economic Optimization And Life Cycle Assessment For A Fully Modular Wheelchair Accessibility Ramp Utilizing Recyclable Materials, Nicolas Whelan

Honors Scholar Theses

In response to the growing emphasis on sustainability and accessibility in infrastructure development, this research paper delves into the optimization of economic opportunities presented by fully modular wheelchair accessibility ramps. By integrating principles of modularity, recyclability, and circular design, these ramps offer a promising solution to the dual challenges of accessibility and environmental impact. The study employs interdisciplinary methods, merging design, economics, and environmental sustainability, to evaluate the feasibility and potential of these innovative ramp designs. Central to the analysis is the application of a Life Cycle Assessment (LCA) to quantify the environmental impact and carbon footprint associated with modular …

Material Modeling Of An Ultraviolet Sensitive Resin At High Pressures And Rates, Truman Miller Russell

Master's Theses (2009 -)

A full understanding of the behavior of binder materials under shock loading is required for effective simulation of heterogeneous polymer-binder-explosives (PBX) and polymer-binder-surrogate (PBS) systems. An accurate simulation is critical for the ultimate goal of designing meso-scale heterogeneous PBS systems. The binder materials studied here is an ultraviolet sensitive resin (UV resin). The UV resin is manufactured by AnyCubic. It is a glassy thermoset polymer and is known to be similar to polymethyl methacrylate (PMMA) both in mechanical properties and in chemical makeup. This material was chosen as it can be additively manufactured, and it will present a lower impedance …

Experimental Investigations And Optimization Of 3d Printed Cellular Structures For Protection Against Traumatic Brain Injury, Aaron R. Jackson

Mechanical and Aerospace Engineering Dissertations - Archive

Traumatic Brain Injury (TBI) disrupts brain function due to head impacts, blast exposures, and ballistic penetrations. It is a significant cause of mental health issues and disability, particularly among military personnel. Historically, combat helmets were designed primarily to protect against fragments. However, recent data highlights the need for helmets that also protect against blast and blunt impacts. Effective TBI prevention requires helmets that address various energy threats while remaining lightweight. A critical metric in this effort is head acceleration, which is closely linked to injury across different scales of brain damage.

Four lattice structures were 3D printed using Digital ABS …

Enhancing Robotic Exploration Through Semantically-Guided Sampling Strategies, Christopher Alexander Arend Tatsch

Graduate Theses, Dissertations, and Problem Reports (ETD)

From space and deep-sea exploration to disaster response and environmental monitoring, autonomous robots are essential for advancing science, improving safety, and addressing critical challenges. This dissertation introduces a novel open-source strategy for autonomous robotic exploration: the Semantically-Guided Exploration (SGE) framework. Designed for ground vehicles, SGE integrates semantic understanding into the autonomous exploration process, improving decision-making in complex environments. Specifically, the proposed sampling-based approach uses the information from the semantic segmentation of RGB images and depth images to guide the robot's selection of exploration goals. This method enables the robot to steer away from potential dangers such as large rocks and …

Parametric Optimization Of Friction Stir Welding Of Aa6061-T6 Samples Using The Copper Donor Stir-Assisted Material Method, Aiman H. Al-Allaq, Joseph Maniscalco, Srinivasa Naik Bhukya, Zhenhua Wu, Abdelmageed Elmustafa

Mechanical & Aerospace Engineering Faculty Publications

This study presents an optimization of the process parameters for the effect of copper (Cu) donor material percentage on the friction stir welding (FSW) of AA6061-T6 alloy. Extensive factorial experiments were conducted to determine the significance of the rotational speed (ω), the transverse speed (v), the interface coefficient of friction (μ), and the Cu donor material percentage in the plunge, left, right, and downstream zones. Design Expert 13 software was used to identify the number of simulation experiments to be conducted using the Abaqus simulation software. From Design Expert 13, which is a thorough multi-objective optimization analysis software, we were …

Optimizing Metal 3d Printing, Abram Brown, Lauren Novak

Williams Honors College, Honors Research Projects

Partnered with Lauren Novak we are doing our senior design project on optimizing metal 3D printing with the company nVent. A brief scope of the project is that nVent uses a metal 3D printer to create tooling that is used in a hydraulic pressed and used to create iterations of prototypes during the design process. We will be researching how to decrease the amount the time of the 3D print while doing load tests with v­blocks, wiping tools, and a rib tool. The tests will be on the tooling made using different parameters including infill density, infill geometry, wall thickness, …

Review Of Computational Models For Large-Scale Mdao Of Urban Air Mobility Concepts, Darshan Sarojini, Marius L. Ruh, Jiayao Yan, Luca Scotzniovsky, Nicholas C. Orndorff, Ru Xiang, Han Zhao, Joshua J. Krokowski, Michael Warner, Sebastiaan Pc Van Schie, Ashley Cronk, Alexandre T. R. Guibert, Jeffrey T. Chambers, Lauren Wolfe, Rachel Doring, Robin Despins, Cibin Joseph, Ryan Anderson, Andrew Ning, Hyunjune Gill, Seongkyu Lee, Zeyu Cheng, Zhi Cao, Chunting Mi, Y Shirley Meng, Christopher Silva, Jiun-Shyan Chen, H. Alicia Kim, John T. Hwang

Faculty Publications

The advent of Urban Air Mobility (UAM) has necessitated a paradigm shift in aircraft design from traditional regression methods to physics-based analysis and the use of modern computational methods. This paper explores the intricacies of UAM aircraft design, acknowledging the limitations of historical empirical equations and advocating for the use of physics-based tools in the early stages of the design process. It underscores the importance of Multidisciplinary Design, Analysis, and Optimization (MDAO) as a means to integrate physics-based tools for conceptual design, facilitating decisions on configuration and sizing. The paper presents a comprehensive survey and review of computational models across …

Adaptation Algorithm For Self-Tuning Of Parameters Of Models Of Multi-Stage Flotation Processes, Nilufar Sharifzhanova, Maksadhan Yakubov, Francesco Gregoretti

Technical science and innovation

Modern methods for solving problems of planning the execution of batches of tasks in multi-stage systems are characterized by the presence of restrictions on their dimensionality, the impossibility of guaranteed obtaining better results in comparison with fixed packages for different values of the input parameters of the problem. In the article, the author solved the problem of optimizing the composition of job packages running in multi-stage systems using the branch and bound method. Research has been carried out on various ways to form package execution orders tasks in multi-stage systems (heuristic rules for ordering packages tasks in the sequence of …

On The Development Of A Sensing System Methodology To Evaluate The Viscoelastic Properties Of Soft Tissues As A Means Of Disease Prognosis, Shashank S. Kumat

Mechanical and Aerospace Engineering Dissertations - Archive

Identification of tissue viscoelastic properties could provide valuable information for assessing its healthiness or disease state. Current technologies present challenges to access and perform localized tissue assessment in confined spaces in the human body through contact indentation/palpation. As such, there is a need for a diagnostic system capable of measuring tissue relaxation response at the local site by accessing the tissue through a natural orifice. This dissertation presents a strain gauge-based uniaxial micro-force sensor, part of the aforementioned system, capable of measuring tissue response data in confined human space environments. A sensing system design methodology is developed and presented. The …

Deep Reinforcement Learning For The Design Of Structural Topologies, Nathan Brown

All Dissertations

Advances in machine learning algorithms and increased computational efficiencies have given engineers new capabilities and tools for engineering design. The presented work investigates using deep reinforcement learning (DRL), a subset of deep machine learning that teaches an agent to complete a task through accumulating experiences in an interactive environment, to design 2D structural topologies. Three unique structural topology design problems are investigated to validate DRL as a practical design automation tool to produce high-performing designs in structural topology domains.

The first design problem attempts to find a gradient-free alternative to solving the compliance minimization topology optimization problem. In the proposed …

Extremum Seeking Control Algorithms For Extremely High Frequency Antenna System Pointing, Scott Shore

Mechanical Engineering ETDs

The research examines the application of extremum seeking control (ESC) algorithms to ground station antenna pointing for extremely high frequency (EHF) communication systems. ESC algorithms search for local maxima or minima by locating where an objective function gradient goes to zero. With wireless communication expanding into higher frequencies, the ground station pointing requirement is increasing. ESC presents a method which utilizes available equipment and information to perform ground station pointing. Additionally, ESC algorithms do not rely on assumptions or approximations needed for other techniques. The dissertation demonstrates ESC algorithm feasibility for the ground station pointing problem, benchmarks the ESC algorithms …

Development Of Surrogate-Optimization Models For A Novel Transcritical Power Cycle Integrated With A Small Modular Reactor, Yili Zhang, Jacob Bryan, Geordie Richards, Hailei Wang

Mechanical and Aerospace Engineering Student Publications and Presentations

In recent years, various types of surrogate optimization models have been proposed to reduce the computational time and to improve the emulation accuracy. In this study, by leveraging an ANN surrogate model developed earlier, a comprehensive and efficient optimization algorithm is conceived for the global optimal design of an integrated regenerative methanol transcritical cycle. It combines a unique converging/diverging classifier model into the surrogate model to form a surrogate-based model, which significantly improves the prediction accuracy of the objective function. Six binary classifiers are explored and the multi-layer feed-forward (MLF) neural network classifier is selected. In addition, within the five …

Water Quality Monitoring And Mapping Using Rapidly Deployable Sensor Nodes, Mohamed Abdelwahab

Theses and Dissertations

Efficient and continuous monitoring of water quality parameters plays a pivotal role in responding to pollution incidents and ensuring the safety of both human consumption and ecological resources. This research introduces an affordable and dependable in-situ water quality sensor package designed for seamless continuous monitoring, providing essential data to facilitate informed decision-making in water resource management. The sensor package enables comprehensive on-site assessment of key water characteristics, including pH, temperature, turbidity (measured in NTU), and total dissolved solids (TDS, measured in ppm). Spatial interpolation techniques, specifically Kriging, are employed to extrapolate variable values at unobserved locations based on nearby measurements. …

Design And Implementation Of An Optimization Platform For Common Fixed Photovoltaic Systems, Amro Ahmad Zahrawi

Mechanical Engineering Theses

Most household photovoltaic (PV) panels are installed in a fixed arrangement (fixed-type) based on a rule of thumb that comes from experience. The azimuth angle is usually set facing south with a tilt angle equivalent to the location's latitude. However, research shows that this is not the best for all geographical locations and during all hours of the day. Consequently, this brings up the hypothesis that optimizing the PV system's azimuth and tilt angles would ensure that the PV panel produces the most possible output as it is adjusted to face the sun most effectively during peak sunlight hours. This …

A Globalized Optimization Schema For Automated Fiber Placement Processing Parameters, Matthew John Godbold

Theses and Dissertations

Automated Fiber Placement is an advanced manufacturing technique for industrial-scale composite structures. Advanced robotics coupled with composite manufacturing results in faster and more consistent results than previously obtained through hand layup. The complexity and interconnectedness of the automated fiber placement process provides a difficult challenge for traditional modeling techniques. Modeling within automated fiber placement currently utilizes physics-based modeling to inform the translation of a design to a manufacturing plan. The intricacy of the automated fiber placement process dictates that attempts at modeling or optimizing these processes are often limited in their scope. Physics-based modeling for manufacturing typically involves numerous interacting …

Multi-Objective Design Optimization Of Two Configurations Of Ventricular Shunts For Hydrocephalus, Will Kirkpatrick

Theses and Dissertations

Hydrocephalus is developed when the flow of cerebrospinal fluid is obstructed in the ventricles and a pressure build-up is generated within the brain. Ventricular shunts are used to remove excess fluid from the brain, but these shunts have a common problem of failure due to the shunt being obstructed by the build-up of astrocytes. To address this, two sets of 27 designs of ventricular shunts were identified and analyzed with parameters that could potentially reduce obstruction risks. The performance of these designs was examined using fluid simulations on these two sets of 27 designs. One set explored close-tipped shunt designs, …

Design And Development Of Ultrabroadband, High-Gain, And High-Isolation Thz Mimo Antenna With A Complementary Split-Ring Resonator Metamaterial, Ammar Armghan, Khaled Aliqab, Meshari Alsharari, Osamah Alsalman, Juveriya Parmar, Shobhit K. Patel

Department of Mechanical and Materials Engineering: Faculty Publications

The need for high-speed communication has created a way to design THz antennas that operate at high frequencies, speeds, and data rates. In this manuscript, a THz MIMO antenna is designed using a metamaterial. The two-port antenna design proposed uses a complementary splitring resonator patch. The design results are also compared with a simple patch antenna to show the improvement. The design shows a better isolation of 50 dB. A broadband width of 8.3 THz is achieved using this complementary split-ring resonator design. The percentage bandwidth is 90%, showing an ultrabroadband response. The highest gain of 10.34 dB is achieved …

Novel Approach For Non-Invasive Prediction Of Body Shape And Habitus, Emma Young

Electronic Theses and Dissertations

While marker-based motion capture remains the gold standard in measuring human movement, accuracy is influenced by soft-tissue artifacts, particularly for subjects with high body mass index (BMI) where markers are not placed close to the underlying bone. Obesity influences joint loads and motion patterns, and BMI may not be sufficient to capture the distribution of a subject’s weight or to differentiate differences between subjects. Subjects in need of a joint replacement are more likely to have mobility issues or pain, which prevents exercise. Obesity also increases the likelihood of needing a total joint replacement. Accurate movement data for subjects with …

Comparative Design Space For Bistable Composites: An Integrated Framework Of Optimization, Finite Element Analysis, And Experimental Testing, Jonathan Bolanos

All Theses

Bistable composites are a class of advanced materials that can actuate between two stable shapes, making them attractive for a wide range of engineering applications. However, designing these composites to achieve optimal performance remains a challenging task. To address the challenge, this research develops an integrated framework that combines a genetic algorithm optimization technique, finite element analysis in Abaqus, and experimental testing to explore the design comparative space for square bistable composites composed of DA 409 carbon fibers. This leads to the study of generating an optimization algorithm to account for the relationship between the chances of a successful maximum …

A Value-Based Sequential Optimization Framework For Efficient Materials Design Considering Uncertainty And Variability, Maher Alghalayini

All Dissertations

Many problems in engineering and science can be framed as decision problems in which we choose values for decision variables that lead to desired outcomes. Notable examples include maximizing lift in airplane wing design, improving the efficiency of a power plant, or identifying processing protocols resulting in structural materials with desired mechanical properties. These problems typically involve a significant degree of uncertainty about the often-complex underlying relationships between the decision variables and the outcomes. Solving such decision problems involves the use of computational models or physical experimentation to generate data to make predictions and test hypotheses. As a result, both …

Leveraging Automated Fiber Placement Computer Aided Process Planning Framework For Defect Validation And Dynamic Layup Strategies, Joshua Allen Halbritter

Theses and Dissertations

Process planning represents an essential stage of the Automated Fiber Placement (AFP) workflow. It develops useful and efficient machine processes based upon the working material, composite design, and manufacturing resources. The current state of process planning requires a high degree of interaction from the process planner and could greatly benefit from increased automation. Therefore, a list of key steps and functions are created to identify the more difficult and time-consuming phases of process planning. Additionally, a set of metrics must exist by which to evaluate the effectiveness of the manufactured laminate from the machine code created during the Process Planning …

Comprehensive Process Planning Optimization Framework For Automated Fiber Placement, Alex Ryan Brasington

Theses and Dissertations

Advanced composite materials came about in 1966 and have since been widely used due to the possibility of superior structural performance while also achieving weight reductions. Such opportunities have led to composite materials being used to fabricate complex components, often in the aerospace sector. Most components, especially in aviation, are on a large scale and are outside the capabilities of traditional composite manufacturing techniques. Traditional manufacturing methods are also labor intensive, time consuming, have a high level of material scrap, and are prone to human error. This has led to the need for innovative manufacturing solutions to withstand the ever-increasing …

Non-Intrusive Reduced Order Model Formulation For Inverse Shape Design Including Deforming Meshes And Multiphysics Problems., Kapil Aryal

Mechanical and Aerospace Engineering Dissertations - Archive

Despite significant advancements in computer capabilities for numerical simulations, engineers continue to face limitations when dealing with large-scale full-order model(FOM) simulations. These simulations often necessitate repeated solves, such as those encountered in inverse design, real-time solution prediction, error quantification, and solver convergence, among others. To address these challenges, reduced order modeling (ROM) has emerged as a valuable approach. This thesis focuses on the development of an ROM framework that combines Proper Orthogonal Decomposition (POD) with machine learning techniques. This integrated approach is applied to a diverse range of heat transfer and fluid flow inverse design problems. POD constructs optimal sets …

Initial Procedure For Small-Scale Extraction Of Subsurface Martian Ice, Evan Steers

Electronic Theses and Dissertations

For decades, NASA has been surveying the surface of Mars with plans for human exploration. Due to recent advancements, there is strong evidence to believe that frozen aquifers beneath the Martian surface hold great amounts of usable H2O. Since the discovery of water on Mars, NASA has expressed key interest in harvesting this valuable resource. The presence of usable H2O on Mars could reduce the launching mass of future missions by giving astronauts the capability to harvest water once they have landed on Mars. This research focuses on the optimization of a current design to extract Martian water and the …

Low-Fidelity Design Optimization And Parameter Sensitivity Analysis Of Tilt-Rotor Evtol Electric Propulsion Systems, Tyler Critchfield, Andrew Ning

Faculty Publications

Urban air mobility requires a multidisciplinary approach to tackle the important chal- lenges facing the design of these aircraft. This work uses low-to-mid fidelity tools to model rotor aerodynamics, blade structures, vehicle aerodynamics, and electric propulsion for a tilt-rotor electric vertical takeoff and landing (eVTOL) aircraft. We use gradient-based design optimization and extensive parameter sensitivity analysis to explore the design space and complex tradeoffs of tilt-rotor distributed electric propulsion systems.

Sparsity For Gradient-Based Optimization Of Wind Farm Layouts, Benjamin T. Varela, Andrew Ning

Faculty Publications

Optimizing wind farm layouts is an important step in designing an efficient wind farm. Optimizing wind farm layouts is also a difficult task due to computation times increasing with the number of turbines present in the farm. The most computationally expensive part of gradient- based optimization is calculating the gradient. In order to reduce the expense of gradient calculation, we performed a study on the use of sparsity in wind farm layout optimization. This paper presents the findings of the sparsity study and provides a method to use sparsity in wind farm layout optimization. We tested this sparsity method by …

Multiple Objective Function Optimization And Trade Space Analysis, Yifan Xu

All Theses

Optimization can assist in obtaining the best possible solution to a design problem by varying related variables under given constraints. It can be applied in many practical applications, including engineering, during the design process. The design time can be further reduced by the application of automated optimization methods. Since the required resource and desired benefit can be translated to a function of variables, optimization can be viewed as the process of finding the variable values to reach the function maxima or minima. A Multiple Objective Optimization (MOO) problem is when there is more than one desired function that needs to …

An Application Of Optimized Bistable Laminates As A Low Velocity, Low Impact Mechanical Deterrent, Graham Lancaster

All Theses

This research considers the problem of using bistable laminates as a mechanical deterrent to the impending impact of a particle. The structure will be controlled through an algorithm that will utilize piezoelectric devices to activate them in unison with the bistable laminate to successfully deter. A novel experimental setup will be constructed to ensure that the bistable laminate stays fixed when acting as a mechanical deterrent. Piezoelectricity is the main driving force of the bistable laminate to morph and this study will use a Macro Fiber Composite (MFC) actuator that contains piezoelectric ceramic rods in a patch to transfer electrical …

Multi-Fidelity Predictions For Control Allocation On The Nasa Ikhana Research Aircraft To Minimize Drag, Justice T. Schoenfeld

All Graduate Theses and Dissertations, Spring 1920 to Summer 2023

Optimal control settings (camber scheduling) can be used by aircraft to minimize drag at various operating conditions during flight. In this work, camber schedules for minimum drag on the NASA Ikhana are obtained over a range of lift coefficients. A modern numerical lifting-line algorithm is used to predict the lift and drag of the aircraft as a function of operating condition and wing section shape (airfoil camber). The SLSQP optimization algorithm is used to solve for the camber schedule that minimizes drag for a given operating condition. The process is repeated, varying the number of control sections to evaluate the …