Mechanical Engineering Commons^™

Application And Evaluation Of Full-Field Surrogate Models In Engineering Design Space Exploration, Christopher Murray Thelin

Theses and Dissertations

When designing an engineering part, better decisions are made by exploring the entire space of design variations. This design space exploration (DSE) may be accomplished manually or via optimization. In engineering, evaluating a design during DSE often consists of running expensive simulations, such as finite element analysis (FEA) in order to understand the structural response to design changes. The computational cost of these simulations can make thorough DSE infeasible, and only a relatively small subset of the designs are explored. Surrogate models have been used to make cheap predictions of certain simulation results. Commonly, these models only predict single values …

Unsupervised-Learning Assisted Artificial Neural Network For Optimization, Varun Kote

Mechanical & Aerospace Engineering Theses & Dissertations

Innovations in computer technology made way for Computational Fluid Dynamics (CFD) into engineering, which supported the development of new designs by reducing the cost and time by lowering the dependency on experimentation. There is a further need to make the process of development more efficient. One such technology is Artificial Intelligence. In this thesis, we explore the application of Artificial Intelligence (AI) in CFD and how it can improve the process of development.

AI is used as a buzz word for the mechanism which can learn by itself and make the decision accordingly. Machine learning (ML) is a subset of …

Gaussian Process Regression Applied To Marine Energy Turbulent Source Tuning Via Metamodel Machine Learning Optimization, Sterling Olson

Mechanical Engineering ETDs

Converting energy from the currents found within tidal channels, open ocean, rivers, and canals is a promising yet untapped source of renewable energy. In order to permit current energy converters for installation in the environment, the CECs must be shown to non-negatively impact the environment. While developing these model increased utility may be gained if researchers may optimize mechanical power while constraining environmental effects. Surrogate models have garnered interest as optimization tools because they maximize the utility of expensive information by building predictive models in place of computational or experimentally expensive model runs. Marine hydrokinetic current energy converters require large-domain …

Characterization And Optimization Of A Propeller Test Stand, Colin Bruce Leighton Benjamin

Mechanical & Aerospace Engineering Theses & Dissertations

In recent history, there has been a rapid rise in the use of drones, and they are expanding in popularity each year. The widespread use and future capabilities of these unmanned aerial vehicles (UAVs) will call for increased study and classification of propellers to maximize their performance. As a result, it is necessary to have continuity in the development, maximization, and optimization of propeller test stand’s capability to collect accurate and precise measurements. It is of significant advantage to have the capability of accurately characterizing a propeller based on its thrust and torque. In this study, a propeller test stand …

Analysis Of Horizontal Axis Wind Turbine Array Optimization, Peter-Claver Nwanze, Keith Bazemore, Jessica Lyons, J. Ann Mitchem

ENgaging Educators in Renewable enerGY (ENERGY): Lesson Plans & Slideshows (2017-2019)

Wind energy is the fastest growing form of renewable energy, with a multitude of possibilities for expansion. This, as well as other forms of renewable energy, will facilitate understanding of the growing concerns regarding global warming by decreasing our dependence on fossil fuels. Wind energy requires wind speeds of at least six miles per hour; therefore, only certain geographical areas are suitable for the use of this technology. The purpose of this experiment was to determine whether the orientation of an array of wind turbines increases or decreases energy production and efficiency. In this study, various arrays consisting of five …

Design And Process Of 3d-Printed Parts Using Composite Theory, Jordan Garcia

Theses and Dissertations--Mechanical and Aerospace Engineering

3D printing is a revolutionary manufacturing method that allows the productions of engineering parts almost directly from modeling software on a computer. With 3D printing technology, future manufacturing could become vastly efficient. However, it is observed that the procedures used in 3D printing differ substantially among the printers and from those used in conventional manufacturing. In this thesis, the mechanical properties of engineering products fabricated by 3D printing were comprehensively evaluated and then compared with those made by conventional manufacturing. Three open-source 3D printers, i.e., the Flash Forge Dreamer, the Tevo Tornado, and the Prusa, were used to fabricate the …

Optimal Power Flow Control Of Networked Dc Microgrids, Eddy H. Trinklein

Dissertations, Master's Theses and Master's Reports

The US military is moving toward the electrification of many weapon systems and platforms. Advanced weapon systems such as high energy radar, electro-magnetic kinetic weapons and directed energy pose significant integration challenges due to their pulsed power electrical load profile. Additionally, the weapons platforms, including ships, aircraft, and vehicles can be studied as a mobile microgrids with multiple generation sources, loads, and energy storage. There is also a desire to extend the mission profile and capabilities of these systems. Common goals are to increase fuel efficiency, maintaining system stability, and reduce energy storage size as typically required to enable pulsed …

Optimization And Control Of Arrays Of Wave Energy Converters, Jianyang Lyu

Dissertations, Master's Theses and Master's Reports

Wave Energy Converter Array is a practical approach to harvest ocean wave energy. To leverage the potential of the WEC array in terms of energy extraction, it is essential to have a properly designed array configuration and control system. This thesis explores the optimal configuration of Wave Energy Converters (WECs) arrays and their optimal control. The optimization of the WEC array allows both dimensions of individual WECs as well as the array layout to varying. In the first optimization problem, cylindrical buoys are assumed in the array where their radii and drafts are optimization parameters. Genetic Algorithms are used for …

Time-Dependent Reliability Methodologies With Saddlepoint Approximation, Zhangli Hu

Doctoral Dissertations

"Engineers always encounter time-dependent uncertainties that ubiquitously exist, such as the random deterioration of material properties and time-variant loads. Therefore the reliability of engineering systems becomes time-dependent. It is crucial to predict the time-dependent reliability in the design stage, given possible catastrophic consequences of a failure. Although extensive research has been conducted on reliability analysis, estimating the reliability accurately and efficiently is still challenging. The objective of this work is to develop accurate and efficient reliability methodologies for engineering design. The basic idea is the integration of traditional reliability methods with saddlepoint approximation (SPA), which can accurately approximate the tail …

An Analytical Design Of Experiments Method For Fatigue Constrained Design Optimization Of A 3d Printed Structure, Ashish Pokharel

Mechanical and Aerospace Engineering Theses - Archive

A design of experiments approach has been used to analytically determine a low cycle fatigue (LCF) constraint for use in design optimization of 3D printed structures. In context of metal additive manufacturing, the process of melting, solidification and consolidation of metal powder introduces very high temperature gradient field within the build which in turn results in high compressive stresses at the core and tensile stresses at the outer surface of the part after it has cooled down to room temperature post build. An approach of finite element modeling in ANSYS Additive has been used to develop a residual stress profile …

Internal Deformation Measurements And Optimization Of Synthetic Vocal Fold Models, Cassandra Jeanne Taylor

Theses and Dissertations

Developing lifelike vocal fold models is challenging due to various associatedbiomechanical complexities. Nevertheless, the development and analysis of improved vocal foldmodels is worthwhile since they are valuable tools for gaining insight into human vocal foldvibratory, aerodynamic, and acoustic response characteristics. This thesis seeks to contribute tothe development of computational and physical vocal fold modeling in two ways. First is byintroducing a method of obtaining internal deformation fields within vibrating synthetic vocal foldmodels; second is by presenting an optimization algorithm coupled with a computational vocalfold model to optimize geometry and stiffness of a synthetic vocal fold model to achieve morerealistic vibration …

Design Of Wind Turbine Tower Height And Blade Length: An Optimization Approach, Ryan Wass

Mechanical Engineering Undergraduate Honors Theses

The wind industry is a fast growing market and is quickly becoming competitive with traditional non-renewable energy resources. As with any developing industry, research must continually be redefined as more complex understandings of design variables are learned. Optimization studies are common ways to quickly refine design variable selections. Historical wind turbine data shows that the tower hub height to rotor diameter ratio scales almost linearly. However there is no specific rule that dictates the optimum hub height for a given diameter. This study addresses this question by using an Excel based optimization program to determine the height to diameter ratio …

Efficient Incorporation Of Fatigue Damage Constraints In Wind Turbine Blade Optimization, Bryce Taylor Ingersoll

Theses and Dissertations

Improving the wind turbine blade design has a significant effect on the efficiency of the wind turbine. This is a challenging multi-disciplinary optimization problem. During the blade design process, the aerodynamic shapes, sizing of the structural members, and material composition must all be determined and optimized. Some previous blade design methods incorporate the wind turbine's static response with an added safety factor to account for neglected dynamic effects. Others incorporate the dynamic response, but in general is limited to a few design cases. By not fully incorporating the dynamic response of the wind turbine, the final turbine blade design is …

Process Improvement At "The Manse On Marsh", Kevin C. Manko

Industrial and Manufacturing Engineering

The Manse on Marsh is an independent and assisted living facility that prides itself on providing life-enriching care for the elderly. Considering that the staff is essential to supply this care and turnover rates are a constant factor, the company would like to reduce the time it takes to hire new employees by at least one week. To facilitate this goal, process flow maps are utilized to assess the current state of the hiring process and metrics are applied to support future state design decisions. After performing a value added analysis and identifying areas of waste, a total of 20 …

Vial Of Life Redesign, Andrew Scott Heim, Marisonn Manalo

Industrial and Manufacturing Engineering

Cambria Anonymous Neighbors (CAN), a nonprofit organization assisting the residences of Cambria, hopes to standardize first responder procedures and make medical information easily accessible in case of a medical emergency. Currently the container costs $3.78. CAN would like to provide 2000 containers at a lower cost. After researching materials, acrylic was found to be the best option for the container material due to its low cost and durability. A laser cutter was used to cut the acrylic pieces, and then a set of step by step instructions were created to assemble the product. To reduce the cost of acrylic, the …

Healing Alternatives Workspace Remodel, Lissandra Ilcyn, Jenifer Astrid Colmenares, Grace E. Kuffner

Industrial and Manufacturing Engineering

Healing Alternatives is an acupuncture office space located in a repurposed house in San Luis Obispo. Healing Alternatives’ current facility layout does not allow for an additional treatment room or the space to provide additional services because of the wasted space within the facility. Furthermore, patients can be disrupted by noise outside the treatment room causing a negative customer experience. The project team’s objectives are to:

o Design two layout alternatives

o Provide a time estimate for each alternative

o Provide a cost analysis of each alternative

o Implement 5s methodology on the storage room

o Provide a 2D-3D model …

Development And Optimization Of Alumina Fine Fibers Utilizing A Centrifugal Spinning Process, Mandana Akia, Dulce Capitanachi, Misael E. Martinez, Carlos Hernandez, Hector De Santiago, Yuanbing Mao, Karen Lozano

Mechanical Engineering Faculty Publications

Highlights

• Successful synthesis of AIP/PVA composite fibers using Forcespinning® techniques.

• Optimization of the operating parameters applying response surface methodology (RSM).

• Fabrication of mesostructured gamma alumina and highly crystalline alpha alumina fine fibers.

Abstract

Aluminum isopropoxide and poly(vinylalcohol) fine fibers were successfully fabricated and optimized utilizing the response surface methodology. The optimized composite fibers showed mean fiber diameter of 304 nm. The fiber samples were calcined at different temperatures to attain both gamma and alpha phases of alumina. Various characterization methods including scanning electron microscopy, thermogravimetric analysis, x-ray diffraction and nitrogen adsorption/desorption analysis were conducted. The BET analysis …

Methods For The Aerostructural Design And Optimization Of Wings With Arbitrary Planform And Payload Distribution, Jeffrey D. Taylor

All Graduate Theses and Dissertations, Spring 1920 to Summer 2023

The design of an aircraft wing often involves the use of mathematical methods for simultaneous aerodynamic and structural design. The goal of many of these methods is to minimize the drag on the wing. A variety of computer models exist for this purpose, but some require the use of expensive time and computational resources to give meaningful results. As an alternative, some mathematical methods have been developed that give reason ably accurate results without the need for a computer. However, most of these methods can only be used for wings with specific shapes and payload distributions. In this thesis, a …

Geometric Optimization Of A Heaving Point Absorber Wave Energy Converter, Ian Riley

College of Graduate Studies: Theses & Dissertations

Wave energy shows significant potential for development into a competitive renewable energy source. Non-renewable resources are finite and contribute to adverse effects on the environment. Development of wave energy conversion devices that use heave motion as the primary driver for converting wave energy into electrical potential is explored through optimizing the geometry of an axisymmetric partially submerged buoy in deep water. The governing equations of motion and hydrodynamic forces are solved for in one degree of freedom using ANSYS Aqwa. An external PTO device is simulated to induce power capture in the system. Four different geometric shapes are tested and …

Electrical Response Of Thermoelectric Generator To Geometry Variation Under Transient Thermal Boundary Condition, Elias Yazdanshenas, Alireza Rezania, Meysam Karami Rad, Lasse Rosendahl

Mechanical & Aerospace Engineering Faculty Publications

A three-dimensional numerical model is applied in this study to illustrate the electrical response of a thermoelectric generator (TEG) during transient heat flux at the hot side. In this work, various types of thermal boundary conditions are considered to evaluate the performance of the TEG. Thus, a TEG under pulsed heat flux is studied numerically, and the numerical model is verified by experimental results. With the consideration of a defined reference geometry, different heat flux frequencies are applied in order to evaluate the corresponding electrical output by the TEG. In addition, variation of the module performance for various TEG leg …

Optimization Of Heat Sinks In A Range Of Configurations., Archibald Allswell Amoako

Electronic Theses and Dissertations

In this study, different heatsink geometries used for electronic cooling are studied and compared to each other to determine the most efficient. The goal is to optimize heat transfer of the heat sinks studied in a range of configuration based on fin geometry. Heat sinks are thermal conductive material devices designed to absorb and disperse heat from high-temperature objects (e.g. Computer CPU). Common materials used in the manufacturing of heat sinks are aluminum and copper due to their relatively high thermal conductivity and lightweight [1]. Aluminum is used as the material for the heatsinks studied in this research project. To …

Design Optimization Of A Non-Axisymmetric Endwall Contour For A High-Lift Low Pressure Turbine Blade, Jacob Allen Dickel

Browse all Theses and Dissertations

Various approaches have been used to shape the geometry at the junction of the endwall and the blade profile in high-lift low-pressure turbine passages in order to reduce the endwall losses. This thesis will detail the workflow to produce an optimized non-axisymmetric endwall contour design for a front-loaded high-lift research turbine profile. Validation of the workflow was performed and included a baseline planar and test contour case for a future optimization study. Endwall contours were defined using a series of Bezier curves across the passage to create a smooth surface. A parametric based approach was used to develop the test …

Coupling Computational Fluid Dynamics Analysis And Optimization Techniques For Scramjet Engine Design, Nathan T. Mcgillivray

Browse all Theses and Dissertations

Various aspects of hypersonic vehicles are being rapidly explored for improved functionality. One of the main areas of consideration is the fueling of a Supersonic Combusting Ramjet (scramjet) engine. Using Computational Fluid Dynamics (CFD), computer simulations can be performed to analyze the flow physics of a scramjet. In this research, an optimization code, Dakota, is integrated with the CFD to optimize a set of parameters to maximum thrust. In this study, the fuel injection and combustion is replaced with heat sources. This simplification greatly reduces the computational requirements. Additionally, the 3D geometry is reduced to an axisymmetric 2D geometry because …

A Monolithic Internal Strain-Gage Balance Design Based On Design For Manufacturability, Thomas Ladson Webb Iii

Mechanical & Aerospace Engineering Theses & Dissertations

This paper proposes an alternative approach to internal strain-gage balance design driven by Design for Manufacturability (DFM) principles. The objective of this research was a reduction in fabrication time and, subsequently, cost of a balance by simplifying its design while maintaining basic stiffness and sensitivity. Traditionally, the National Aeronautics and Space Administration (NASA) Langley Research Center (LaRC) balance designs have relied on Electro-Discharge Machining (EDM), which is a precise but slow and, therefore, expensive process. EDM is chosen due to several factors, including material hardness, surface finish, and complex geometry, including blind cuts. The new balance design objectives require no …

Optimization And Control Of An Array Of Wave Energy Converters, Jianyang Lyu

Dissertations, Master's Theses and Master's Reports

This study explored optimal configuration of both the array layout and the dimension of each WEC in the array. The array contains heaving buoys with full interaction and exact hydrodynamics. Optimization of dimension was done on each WEC in the array with a given optimal layout, and a higher q-factor was achieved. Both impedance matching optimal control and derivative control were employed, which provides both theoretical maximum energy and a more realistic case. Then the work was expanded to optimization of both the array layout and the dimension of each WEC in the array. An average of 39.21% higher q-factor …

Indonesia’S Municipal Solid Waste 3r And Waste To Energy Programs, Farizal Farizal, Radityo Aji, Amar Rachman, Nasruddin Nasruddin, Teuku Meurah Indra Mahlia

Makara Journal of Technology

Like most cities in the world, population in Indonesia continues to grow every year. Problems that can arise from this are the increasing amount of municipal solid waste (MSW) production and the growing demand for electricity. To deal with the problems, Indonesian government runs 3R (Reduce, Reuse and Recycle) and WTE (Waste to Energy) Programs simultaneously. 3R program aims to reduce the number of waste, while WTE program aims to generate electricity as an alternative energy source. This study aims to find out the optimal proportion of MSW treated through the 3R and WTE programs. For the purpose, a goal …

Optimization Of Aircraft Tow Steered Composite Wing Structures, Micheal Chamberlain Henson

Mechanical and Aerospace Engineering Dissertations - Archive

An efficient methodology for design of aircraft composite wing structures is presented. The developed approach provides a flexible and integrated strategy to leverage advantages of composite material tow steering to achieve more effective wing designs. This is accomplished by including the coupling between OML geometry, aerodynamics and structural response. Structural and aerodynamic analyses are derived from parametric aircraft geometry and assembled into a framework for aero-structural wing sizing. A Ritz equivalent plate solution is extended to model composite materials with variable fiber path geometry. The structural modeling approach is implemented to automate creation of both Ritz and finite element analyses. …

A Methodology For Topology And Lattice Structure Optimization Of A Cargo Drone Motor Mount, Nagadurga Srinivas Sripada

Mechanical and Aerospace Engineering Theses - Archive

This work discusses a CAE driven methodology for designing a lightweight component by performing structural configuration on a given package space, creating a closed surface along this configuration using an interactive geometric modeling tool, and lastly generating lattice members that provide the required stiffness for the structure. The design process is explained starting with topology optimization performed on a single block with specific design constraints. It describes the effect of different parameters on the optimized results and how to analyze these results based on a given volume fraction constraint with the objective of minimizing the compliance. It then talks about …

Design And Analysis Of Compressed Air Power Harvesting Systems, Zachary James Sadler

Theses and Dissertations

Procedure for site discovery, system design, and optimization of power harvesting systems is developed with an emphasis on application to air compressors. Limitations for the usage of infrared pyrometers is evaluated. A system of governing equations for thermoelectric generators is developed. A solution method for solving the system of equations is created in order to predict power output from the device. Payback analysis is proposed for determining economic viability. A genetic algorithm is used to optimize the power harvesting system payback with changing quantities and varieties of thermoelectric generators, as well as the back work put into cooling the thermoelectric …

Optimization And Control Of Production Of Graphene, Atharva Hans, Nimish M. Awalgaonkar, Majed Alrefae, Ilias Bilionis, Timothy S. Fisher

The Summer Undergraduate Research Fellowship (SURF) Symposium

Graphene is a 2-dimensional element of high practical importance. Despite its exceptional properties, graphene’s real applications in industrial or commercial products have been limited. There are many methods to produce graphene, but none has been successful in commercializing its production. Roll-to-roll plasma chemical vapor deposition (CVD) is used to manufacture graphene at large scale. In this research, we present a Bayesian linear regression model to predict the roll-to-roll plasma system’s electrode voltage and current; given a particular set of inputs. The inputs of the plasma system are power, pressure and concentration of gases; hydrogen, methane, oxygen, nitrogen and argon. This …