Open Access. Powered by Scholars. Published by Universities.®

Mechanical Engineering Commons™

Open Access. Powered by Scholars. Published by Universities.®

Mechanical Engineering

Discipline
Institution
Publication Year
Publication
Publication Type
File Type

Articles 301 - 306 of 306

Full-Text Articles in Mechanical Engineering

Chemical Stability Study Of Bace0.9Nd0.1O3−Α High Temperature Proton-Conducting Ceramic, Fanglin Chen, O. Toft Sorensen, Guangyao Meng, Dingkum Peng Jan 1997

Chemical Stability Study Of Bace0.9Nd0.1O3−Α High Temperature Proton-Conducting Ceramic, Fanglin Chen, O. Toft Sorensen, Guangyao Meng, Dingkum Peng

Faculty Publications

BaCe0.9Nd0.1O3−a (BCN) ceramic is known to be an excellent high-temperature proton conductor and is a candidate electrolyte for use in solid oxide fuel cells, hydrogen or steam sensors and steam electrolysers. In this work, the chemical stability of BCN was investigated systematically by combining XRD and DTA–TG techniques to study its processing compatibility and its feasibility in potential applications. It was found that above 1200 °C, BCN reacted with alumina or zirconia, leading to the loss of barium and an excess of cerium. In cold water, both sintered BCN disks and powder samples had very …

Go to article

Preparation Of Nd-Doped Baceo3 Proton-Conducting Ceramics By Homogeneous Oxalate Coprecipitation, Fanglin Chen, Ping Wang, O. Toft Sorensen, Guangyao Meng, Dingkum Peng Jan 1997

Preparation Of Nd-Doped Baceo3 Proton-Conducting Ceramics By Homogeneous Oxalate Coprecipitation, Fanglin Chen, Ping Wang, O. Toft Sorensen, Guangyao Meng, Dingkum Peng

Faculty Publications

Nd-doped BaCeO3 have been obtained from homogeneous coprecipitated oxalates when calcined at temperatures T≥1000 °C. Ball-milling of the calcined powders well disperses the agglomerates and consequently has a beneficial effect in the densification process. The calcination temperature has a major influence on the sintering process and powders calcined at 1100 °C possess good sinterabilities. The pressure applied to press the green pellets has no apparent influence on the sintered density at sintering temperatures of T≥1400 °C. By controlling the processing variables it was possible to obtain near fully dense Nd-doped BaCeO3 ceramics with homogeneous microstructure at a sintering …

Go to article

System Modeling And Control Of Smart Structures, Frank J. Kern, Leslie Robert Koval, K. Chandrashekhara, Vittal S. Rao Jan 1995

System Modeling And Control Of Smart Structures, Frank J. Kern, Leslie Robert Koval, K. Chandrashekhara, Vittal S. Rao

Electrical and Computer Engineering Faculty Research & Creative Works

This paper presents multidisciplinary research and curriculum efforts at the University of Missouri-Rolla in the smart structures area. The primary objective of our project is to integrate research results with curriculum development for the benefit of students in electrical, and mechanical and aerospace engineering and engineering mechanics. The approach to the accomplishment of curriculum objectives is the development of a two-course sequence in the smart structures area with an integrated laboratory. The research portion of the project addresses structural identification and robust control methods for smart structures. A brief summary of the research results and a description of curriculum development …

Go to article

The Asymptotic Structure Of Transient Elastodynamic Fields At The Tip Of A Stationary Crack, Xiaomin Deng Jul 1994

The Asymptotic Structure Of Transient Elastodynamic Fields At The Tip Of A Stationary Crack, Xiaomin Deng

Faculty Publications

The asymptotic structure of the transient elastodynamic near-tip fields around a stationary crack is investigated for all three fracture modes. The transient fields are obtained as the sum of their quasi-static counterparts and corresponding transient correction terms, in terms of variable-separable expansions. By allowing the coefficients of terms in the quasi-static expansion to deviate from their quasi-static restrictions, the correction terms are shown to be the particular solutions of a set of first order (for mixed mode I and II) or second order (for mode III) ordinary differential equations with constant coefficients and non-homogeneous terms involving only sine and cosine …

Go to article

On Stationary And Moving Interface Cracks With Frictionless Contact In Anisotropic Bimaterials, Xiaomin Deng Dec 1993

On Stationary And Moving Interface Cracks With Frictionless Contact In Anisotropic Bimaterials, Xiaomin Deng

Faculty Publications

The asymptotic structure of near-tip fields around stationary and steadily growing interface cracks, with frictionless crack surface contact, and in anisotropic bimaterials, is analysed with the method of analytic continuation, and a complete representation of the asymptotic fields is obtained in terms of arbitrary entire functions. It is shown that when the symmetry, if any, and orientation of the anisotropic bimaterial is such that the in-plane and out-of-plane deformations can be separated from each other, the in-plane crack-tip fields will have a non-oscillatory, inverse-squared-root type stress singularity, with angular variations clearly resembling those for a classical mode II problem when …

Go to article

A Kinematically Intelligent Blackboard For Computer Aided Instruction, J. Keith Nisbett, D. Watkins, Clark R. Barker Nov 1993

A Kinematically Intelligent Blackboard For Computer Aided Instruction, J. Keith Nisbett, D. Watkins, Clark R. Barker

Mechanical and Aerospace Engineering Faculty Research & Creative Works

A CAI (computer-aided instruction) package is being developed to be used as a classroom tool for the instruction of undergraduate mechanical engineering students in an introductory kinematics of mechanisms course. This graphical environment allows the instructor to emulate on the projected graphics screen everything that is currently done on the blackboard for planar mechansims. Unlike the blackboard, the software will have the intelligence to interpret the drawings in a kinematic sense so that the drawing of the linkage will behave as a linkage. The software environment involves three principal components: (1) a sketching method for defining the linkage, (2) the …

Go to article

First Prev