Mechanical Engineering Commons^™

Effect Of Aggregation And Particle Size On The Thermal Conductivity Of Nickel-Epoxy Nanocomposites, Jacob M. Faulkner, Xiangyu Li, Xiulin Ruan Dr.

The Summer Undergraduate Research Fellowship (SURF) Symposium

Microprocessor advancements have been stunted in recent years by inadequate means of heat dissipation as power continues to grow and size continues to shrink. One way to increase thermal conductivity while maintaining electrical insulation is to add metal nanoparticles to a polymer matrix. This cheap material has become a popular thermal interface for this reason. However, optimization of the interface is dependent upon a number of factors including particle size, shape, orientation, and aggregation. Various theoretical models and numerical approximations have been developed to find the effective thermal conductivity of such nanocomposites, but none has been able to fully incorporate …

Atomistic And Mesoscopic Simulations Of Heat Transfer Across Heterogeneous Material Interfaces, Sridhar Sadasivam

Open Access Dissertations

The study of heat transfer and the associated thermal interface resistance at heterogeneous material interfaces is over 70 years old since the first measurements of thermal interface resistance by Kapitza in 1941. However, recent developments in experimental metrology techniques that enable spectrally-resolved phonon transport measurements at the nanoscale along with the development of high-fidelity simulation methods have provided a renewed interest in the fundamental physics of heat transfer across interfaces. Miniaturized electronic devices and nanostructured materials for energy applications are among technologies that would benefit from a fundamental understanding of interfacial thermal transport. This dissertation focuses on the study of …

Thermal Modeling And Nanoindentation Of Shape Memory Alloy Thin Films, Mehmet Mete Ozturk

Theses and Dissertations

Metal alloys which go through a hysteric transformation due to external stimuli such as thermal and/or mechanical fields are called shape memory alloys (SMA). Thin films of SMAs have many remarkable features and have been used in the fabrication of microactuators. One potential application is a SMA thin film based information storage device. In all these applications, the existence of the strong thermomechanical coupling inherent in the phase transformation is seen. Due to coupling, knowledge of not only the mechanical field but also the thermal field is essential. The objective of this work is to study the thermal behavior of …

Modeling Atypical Building Use With Commercially Available Building Simulation Software, Sarah E. Schanck

Theses and Dissertations

National Guard armories are audited to provide recommendations for future energy reduction measures. The annual energy consumption of a New Jersey National Guard Armories cannot be modeled directly with commercially available building simulation software, due to discrepancies between the modeling capabilities of the software and the reality of the armory. A building simulation software, eQUEST, was chosen for use in this project. Discrepancies between eQUEST inputs and reality were identified and correction factors developed to minimize the effect of each discrepancy on predicted energy consumption, with the end goal of accuracy between predicted and actual energy consumption. In addition, an …

Fluid Analysis In Solar Heat Pipes, Ben Krumholz, Michael Agavo, William Dundon

Mechanical Engineering

Evacuated tube solar collectors are efficient systems that use heat pipes to facilitate heat transfer. They use incoming solar radiation to heat water. Professor Mason Medizade tasked the team with choosing a component of the system to research and test its influence on system performance. The team investigated the working fluid that runs through the heat pipes. Distilled water, acetone, and ethanol at a range of fill volumes form 1 mL to 11 mL were tested. The team's goal was to find a volume for each fluid to maximize performance of the system. Performance was defined as average temperature rise …

Oscillatory Flow Mechanism For Enhanced Heat Transfer, Sultan Taher Raml

Doctoral Dissertations and Master's Theses

This research project is about the use of an oscillatory flow mechanism to enhance heat transfer. The idea behind this is to induce oscillation of the end wall of one of two connected chambers of a heat exchanger which effectively will induce oscillation of the boundary layer within the connecting duct. The main idea of this thesis came from using species separation studies before 40 years ago in hyperventilation technology to help patients under anesthesia in hospitals. There are many applications for this research such as removing heat from chemical reactors, electrical devices and other enclosed environments such as submarines, …

Characterization Of Pool Boiling Heat Transfer From Porous-Coating-Enhanced Surfaces, Suchismita Sarangi

Open Access Dissertations

Development of techniques for enhancement and optimization of thermal management technologies has been a highly active area of research in recent decades in response to the rapid emergence of compact, high-power electronic systems. Immersion cooling by boiling is one of the preferred methods for high power density applications, due to its passive nature and high heat transfer coefficients obtained. Pool boiling heat transfer has been extensively studied in recent decades to understand the inherent mechanisms yielding the high heat transfer rates, as well as to further enhance the heat transfer by simple modifications or additions to existing approaches. This thesis …

Dynamic Control Of Radiative Surface Properties With Origami-Inspired Design, Rydge B. Mulford, Matthew R. Jones, Brian D. Iverson

Faculty Publications

Thermal management systems for space equipment commonly use static solutions that do not adapt to environmental changes. Dynamic control of radiative surface properties is one way to respond to environmental changes and to increase the capabilities of spacecraft thermal management systems. This paper documents an investigation of the extent to which origami-inspired surfaces may be used to control the apparent absorptivity of a reflective material. Models relating the apparent absorptivity of a radiation shield to time-dependent surface temperatures are presented. Results show that the apparent absorptivity increases with increasing fold density and indicate that origami-inspired designs may be used to …

The Design, Fabrication, And Validation Of A Film Cooled Rotating Turbine Cascade With An Actively Cooled Shroud In A Closed Loop Wind Tunnel, Christopher Michael Drewes

LSU Master's Theses

To test shroud and blade cooling effectiveness, a closed loop, heated wind tunnel housing a film cooled rotating turbine cascade with prescribed blade and vane geometry surrounded by a fully cooled shroud with a leading edge gap were designed and assembled on Louisiana State University’s campus. Heat transfer coefficients and film cooling effectiveness results were computed using a 1-D semi-infinite solid conduction analysis of material temperatures obtained with liquid crystal thermography. Proper analysis required a step change in air temperature; so a bypass loop provided mainstream air heating while maintaining the shroud and blades at ambient temperature. Also, analysis required …

Combustion Wave Propagation Enhancement Of A Nitrocellulose Solid Monopropellant, Omar R. Yehia, Shourya Jain, Li Qiao

The Summer Undergraduate Research Fellowship (SURF) Symposium

Improvement and control of the burning behavior and characteristics of solid fuels promise improved performance of systems ranging from solid rocket motors to microelectromechanical systems. Introducing methods to enhance combustion wave propagation velocities of solid propellants is a crucial step in realizing improved performance in rocket motors that use organic nitrate-based propellants. This work aims to enhance the burning characteristics of solid fuels through the use of thermally guided combustion waves. In order to increase the burning rate of solid nitrocellulose fuel layers, graphite sheets were used as thermally conductive bases in order to substantially improve heat transfer to unburned …

Flexible Thermoelectric Generators For Biomedical Applications, Ryan Stevenson

Boise State University Theses and Dissertations

The market for implantable medical devices is growing rapidly. Research and Markets predicts that by the end of 2015 the market for pacemakers will be 5.1 billion dollars, and a projected growth of 13.82% between 2013 and 2018. The average lifespan of an implantable medical device’s battery is only 5 years, while the projected lifespan of the device itself is 10 years. There is an excess of invasive surgeries occurring to replace these batteries, costing the healthcare system millions of dollars and also causing patients a large degree of discomfort and pain.

Thermoelectric generators have the potential to supplement and …

Simulation And Validation Of Radio Frequency Heating Of Shell Eggs, Soon Kiat Lau

Department of Food Science and Technology: Dissertations, Theses, and Student Research

Finite element models were developed with the purpose of finding an optimal radio frequency (RF) heating setup for pasteurizing shell eggs. Material properties of the yolk, albumen, and shell were measured and fitted into equations that were used as inputs for the model. When the egg was heated by itself, heating tend to be focused at the air cell to result in a “coagulation ring.” The focused heating near the air cell of the egg prevented satisfactory pasteurization of the egg, but deeper analysis of the simulation results offered a new perspective on how non-uniform RF heating could occur in …

Composite Brake Rotor Assembly By Utilizing Replaceable Friction Surfaces, John Evert

Mechanical Engineering and Technology Senior Projects

This project investigated a proof of concept design involving a rotor fabricated from aluminum with replaceable friction surfaces with greater or equal performance characteristics in order to reduce cost and maintenance. The replaceable friction surfaces provide a means to mitigate cost to the end user. The structure is constrained by the dimensions, 11.75” diameter and 1.25” width and serves as a direct replacement rotor for a circle track racecar. Analyses provide a direct comparison in static mass, moments of inertia, and forced convection thermal calculations in order to determine if the concept was viable. Requirements for a successful design were …

Solar Evaporative Fan Coil Unit, Samuel Budnick, Kyle Kluever, Jeremy Dickson

Mechanical Engineering and Technology Senior Projects

The purpose of any engineering project is to anticipate a need and meet that need through prediction analysis and design. Over 70% of the nation’s energy is consumed by building infrastructure such as HVAC systems, electrical, etc. HVAC systems use boilers to generate hot water or steam to heat buildings and evaporative chillers to provide air conditioning, much like the central plant here on campus. The project included the construction of a solar collector that will heat water to 140F in order to run it through a heat exchanger that can have air passed over it. An evaporative chiller was …

A Full Coverage Film Cooling Study: The Effect Of An Alternating Compound Angle, Justin Hodges

Electronic Theses and Dissertations

This thesis is an experimental and numerical full-coverage film cooling study. The objective of this work is the quantification of local heat transfer augmentation and adiabatic film cooling effectiveness for two full-coverage film cooling geometries. Experimental data was acquired with a scientific grade CCD camera, where images are taken over the heat transfer surface, which is painted with a temperature sensitive paint. The CFD component of this study served to evaluate how well the v2-f turbulence model predicted film cooling effectiveness throughout the array, as compared with experimental data. The two staggered arrays tested are different from one another through …

High Regression Rate Hybrid Rocket Fuel Grains With Helical Port Structures, Stephen A. Whitmore, Sean D. Walker, Daniel P. Merkley, Mansour Sobbi

Mechanical and Aerospace Engineering Faculty Publications

Results froma development campaign, where modern additive manufacturing methods are used to fabricate hybrid rocket fuel grains with embedded helical ports, are presented. The fuel grains were constructed from acrlyonitrile butadiene styrene using commercially available three-dimensional printer feedstockmaterial.Gaseous oxygen is used as the oxidizer for this test campaign.When compared to cylindrical fuel ports, significant increases in fuel regression rates were observed, and these increases in regression rate diminished with time as the helical fuel port burns to become progressivelymore cylindrical. Comparisons to the helical pipe flow skin friction correlation developed by Mishra and Gupta indicate that increased skin friction only …

Enhancement Techniques Of Boiling Heat Transfer, Basim Qasim Ali Al-Sukaini

Doctoral Dissertations and Master's Theses

The aim of this study is to investigate pool boiling performance of water under atmospheric pressure by two techniques. The first method is by adding small amounts of surfactants, and the second way is by using structured surfaces.

The first technique is investigated experimentally with environmentally friendly surfactants. The surfactants chosen for the study are an ionic sodium lauryl sulfate (SLS), nonionic ECOSURF™ EH-14, and nonionic ECOSURF™ SA-9. It is observed that adding a small amount of surfactant alters the water boiling phenomenon significantly. Boiling curves for different concentrations are shifted to the left. The wall temperature drops greatly with …

Dropwise Condensation Dynamics In Humid Air, Julian Eduardo Castillo Chaco

Open Access Theses

Dropwise condensation of atmospheric water vapor is important in multiple practical engineering applications. The roles of environmental factors and surface morphology/chemistry on the condensation dynamics need to be better understood to enable efficient water-harvesting, dehumidication, and other psychrometric processes. Systems and surfaces that promote faster condensation rates and self-shedding of condensate droplets could lead to improved mass transfer rates and higher water yields in harvesting applications. The thesis presents the design and construction of an experimental facility that allows visualization of the condensation process as a function of relative humidity. Dropwise condensation experiments are performed on a vertically oriented, hydrophobic …

Characterization And Optimization Of Thermal Protective Fabrics Designed To Protect Against Splash Hazards, Jeremy Osguthorpe

Theses and Dissertations

Thermal textiles used in Personal Protective Equipment (PPE) are used to protect individuals from the hazards of thermal energy. An analytical model of the diffusion of thermal energy within the fabric was developed to simulate the transfer of thermal energy due to a hot liquid splash. Based on the model results, it was determined that that the use of an orthotropic material in which the thermal conductivities in the radial and axial directions are different can be used to decrease the amount of heat transferred through the fabric and thereby increase amount of protection in PPE. An orthotropic material particularly …

Formula Sae Cooling System Design, Lisa Van Den Berg, Brandon Lofaro

Mechanical Engineering

The overall objective of this senior project is to develop, via testing and analysis, a guided process that will aid the Cal Poly Formula SAE team in designing their cooling system. More specifically, a set of designed tests will yield the results necessary in determining a combination of fan and radiator that will achieve appropriate cooling.

A test section that has the capability of interfacing with both the wind tunnel in the Thermal Science Lab and a radiator will be used to facilitate the necessary experiments. The wind tunnel is powered by fan controlled by a variable frequency drive that …

Bridging The Nano- And Macro-Worlds: Thermal Property Measurement Using Thermal Microscopy And Photothermal Radiometry – Application To Particle-Irradiation Damage Profile In Zirconium Carbide, Colby Bruce Jensen

All Graduate Theses and Dissertations, Spring 1920 to Summer 2023

Multiscaled experimental investigations of heat transfer from nanoscales to macroscales are requisite to progress in energy technologies. In nuclear applications, material properties can undergo significant alteration due to destructive interaction with irradiating particles at microstructural levels that affect bulk properties. This study expands the current knowledge base regarding thermal transport in ion-irradiated materials through the use of a multiscaled experimental approach using four complementary thermal wave methods. For the first time, the in-depth thermal conductivity profile of an ion-irradiated sample is measured directly.

An Analytical Model For Heat Transfer Through A Thermoelectric Device Used In Waste Heat Recovery, Zachary Smith, Dr. Matthew Jones

Journal of Undergraduate Research

A considerable amount of energy that is produced in a typical power generation process is rejected to the environment as low-grade waste heat. This heat is rejected at a temperature that is difficult to efficiently convert into electricity. One promising method of recovering this waste heat is through the use of thermoelectric generators (TEGs) that operate by means of the Seebeck effect. Effort has previously been placed in predicting the power output of TEGs. With knowledge of the temperature differential across a thermoelectric device and the properties of the electrical components the device is connected to, the electrical power output …

Development Of Full Surface Transient Thermochromic Liquid Crystal Technique For Internal Cooling Channels, Lucky Tran

Electronic Theses and Dissertations

Proper design of high performance industrial heat transfer equipment relies on accurate knowledge and prediction of the thermal boundary conditions. In order to enhance the overall gas turbine efficiency, advancements in cooling technology for gas turbines and related applications are continuously investigated to increase the turbine inlet temperature without compromising the durability of the materials used. For detailed design, local distributions are needed in addition to bulk quantities. Detailed local distributions require advanced experimental techniques whereas they are readily available using numerical tools. Numerical predictions using a computational fluid dynamics approach with popular turbulence models are benchmarked against a semi-empirical …

The Effects Of Asymmetric Micro Ratchets On Pool Boiling Performance, Lance Austin Brumfield

LSU Doctoral Dissertations

Nucleate boiling is an attractive method for achieving high heat flux at low superheat temperatures. It is frequently used for industrial applications such as heat exchangers and is being considered to cool advanced central processing units (CPU) which produce heat fluxes on the order of 1 MW/m2 and are becoming increasingly less efficient to cool via forced conduction of air. The issue with implementing nucleate boiling as a cooling mechanism lies in the difficulty of quantifying the numerous and complex mechanisms which control the process. A comprehensive nucleate boiling model has yet to be formulated and will be required in …

Heat Transfer Enhancement By Three-Dimensional Surface Roughness Technique In Nuclear Fuel Rod Bundles, Kang Liu

Theses and Dissertations

DISS_abstract> This thesis investigate thermal characteristic of a single-phase nano-fluid in a single heater element loop tester and provides a comparison between heat transfer enhancement results achieved using water as a coolant and using nano-fluids with different volume percentage. The experimental investigation is performed on two simulated nuclear fuel rods with two different types of modified outer surfaces roughness. The fuel rod surfaces modified are termed as two-dimensional surface roughness (square transverse ribbed surface) and three-dimensional surface roughness (Diamond shaped blocks). The nano-fluid used are 0.5% and 2% ZnO-Deionized water based nano-fluid. The maximum heat transfer co-efficient enhancement achieved compared …

Numerical Modeling Of Infrared Thermography Techniques Via Ansys, Hayder Abdulnabi Thajeel

Masters Theses

"Several inspection techniques have been developed over years. Recently, infrared thermography (IRT) technology has become a widely accepted as a nondestructive inspection (NDI) technique for different fields and various applications as well. Infrared thermography stands as one of the most an attractive and a successful NDI technique that has ability to detect the object's surface/subsurface defects remotely based on observing and measuring the surface's emitted infrared heat radiation by using an infrared camera. The finite element modeling FEM ANSYS was successfully used for the modelling of several IRT techniques; such as Pulsed Thermography (PT) and Lock-in Thermography (LT) that can …

Flame Jet Impingement Heat Transfer, Todd Moss, Dr. Brent Webb

Journal of Undergraduate Research

Impinging flame jets are used widely in industry and manufacturing because of their high heat transport characteristics and tight spatial control of the heating. The technique is used in heating or re-heating of stock in the metals and glass industries, and in welding and soldering operations. However, these impinging flame jets are not well understood, and few studies reporting local and average heat transfer characteristics exist in the open literature which might be used by designers (Baukal and Gebhart, 1995a, 199b). The purpose of this research is to experimentally characterize and correlate the local and average heat transfer behavior of …

Thermal Transport To Sessile Water Droplets On Heated Superhydrophobic Surfaces Of Varying Cavity Fraction, Robb C. Hays

Theses and Dissertations

The hydrophobicity of a surface is defined as the degree to which it repels water molecules, and the internal contact angle that the droplet makes with the surface is a measure of the hydrophobicity. Contact angles less than 90° occur on hydrophilic surfaces, while contact angles greater than 90° occur on hydrophobic surfaces. If a surface's contact angle is greater than 120° the surface is commonly defined as superhydrophobic (SH). Superhydrophobicity is accomplished through a combination of microscale surface roughness and water repellant surface chemistry. The roughness creates cavities, or pockets, of vapor underneath the droplet which act to increase …

Computational Fluid Dynamics Validation Of Buoyant Turbulent Flow Heat Transfer, Jared M. Iverson

All Graduate Theses and Dissertations, Spring 1920 to Summer 2023

Computational fluid dynamics (CFD) is commonly used to visualize and understand complicated fluid flow and heat transfer in many industries. It is imperative to validate the CFD computer models in order to avoid costly design choices where experimentation cannot be used to ratify the predictions of computer models. Assessments of CFD computer models in the literature conclude that significant errors occur in computer model predictions of fluid flow influenced by buoyancy forces.

The Experimental Fluid Dynamics Laboratory at Utah State University constructed a wind tunnel with which to perform experiments on buoyancy induced fluid flow. The experiments measured the heat …

Computational Analysis To Enhance Laminar Flow Convective Heat Transfer Rate In An Enclosure Using Aerosol Nanofluids, Andrew Hudson

College of Graduate Studies: Theses & Dissertations

The current research intends to provide a starting point to effectively model aerosol heat transfer in a narrow, enclosed body. This research can lead to future modeling of nano fluids including their heat transfer characteristics and erosion effects on the walls of an enclosure. The model was developed using ICEM CFD for the mesh and FLUENT for the fluid flow modeling. Six different aspect ratio enclosures were developed to study the effects of varying aspect ratio. The natural convection of air was developed first to establish the appropriateness of the models being used. A mesh check was performed using one …