Mechanical Engineering Commons^™

A Model For Condensation Heat Transfer In Hydrophobic-­Hydrophilic Surfaces, Abdulwahab E. Alhashem

Theses and Dissertations

The primary focus of this research is to provide a validated model for a comprehensive understanding of hydrophobic-­‐hydrophilic condensation on patterned-­‐ hybrid surface. Establishing the model requires the modeling of fully dropwise condensation (DWC) before applying modifications to evaluate heat transfer performance of patterned-­‐hybrid condensation surface.

The model for fully DWC consists of defining expressions for heat transfer through a single drop, maximum radius of the drop and drop-­‐size distribution which all are primarily based on the work in the literature. In this work the author utilized a proposed modified version of the simulation for drop-­‐size distribution for fully DWC, …

Development Of Heat Transfer Correlations For Low-Reynolds Numbers, Flows In Horizontal Circular Pipes, Latif Eyada Ibraheem

Dissertations

Turbulent flows are intrinsic to most fluid-based engineering systems, including internal combustion engines. In these devices, mixing, scalar transport and heat transfer are both critical for proper operation and challenging to model. In previous work, Kreun et al. [1] modeled a pre-heated intake manifold of a Diesel engine for cold-start simulations. Accurately predicting the heat transfer at the intake port proved to be a challenging task. Existing heat transfer correlations yielded predictions which were (at best) within 20% of the measured values. The discrepancy was attributed to a mismatch between the range of applicability of existing heat transfer models and …

Using Thermal Gradient Measurements To Compare Bath Temperature And Agitation Effects On The Quenching Performance Of Palm Oil, Canola Oil And A Conventional Petroleum Oil, Bozidar Matijevic, Bruno F. Canale, Božidar Lišcic, George Totten

Mechanical and Materials Engineering Faculty Publications and Presentations

A proprietary Liscic/Petrofer cylindrical Inconel 600 probe of 50-mm diameter and 200-mm length which was instrumented with three thermocouples on the same radius of the crosssection at the middle of the length was used to determine the differences in quenching performance of two vegetable oils, palm oil and canola oil, and they were compared to a locally produced conventional petroleum oil quenchant. The cooling curves and heat transfer performance of these oils were determined at different bath temperatures and agitation rates. The work was performed at the Quenching Research Centre located at the Faculty for Mechanical Engineering, University of Zagreb, …

Numerical Analysis On Convective Cooling Augmented By Evaporative Heat And Mass Transfer For Thermal Power Plant Application, Sudipta Saha

Theses and Dissertations

This thesis work describes a numerical study on the effect of evaporative cooling on the augmentation of forced convective cooling. In recent years, on-demand phase change boosted cooling has drawn major interest where convective heat transfer is augmented/aided by evaporative heat and mass transport processes. This dual mode (convection and evaporation) cooling method is envisioned to drastically enhance the heat transfer coefficient where conventional convective cooling has already reached its maximum value and furthermore dry cooling is still a desired objective. A multi- dimensional mathematical model has been developed to conduct simulations over a range of operating parameters to obtain …

Parallelized Particle Swarm Optimization To Estimate The Heat Transfer Coefficients Of Palm Oil, Canola Oil, Conventional, And Accelerated Petroleum Oil Quenchants, Zoltán Fried, Imre Felde, Rosa L. Simencio Otero, Jônatas M. Viscaino, George E. Totten, Lauralice Canale

Mechanical and Materials Engineering Faculty Publications and Presentations

An inverse solver for the estimation of the temporal-spatial heat transfer coefficients (HTC), without using prior information of the thermal boundary conditions, was used for immersion quenching into palm oil, canola oil, and two commercial petroleum oil quenchants. The particle swarm optimization (PSO) method was used on near-surface temperature-time cooling curve data obtained with the so-called Tensi multithermocouple, and a 12.5 by 45 mm Inconel 600 probe. The fitness function to be minimized by a PSO approach is defined by the deviation of the measured and calculated cooling curves. The PSO algorithm was parallelized and implemented on a graphics accelerator …

Influence Of Micro-Structured Superhydrophobic Surfaces On Nucleation And Natural Convection In A Heated Pool, Adam Cowley, Daniel Maynes, Julie Crockett, Brian D. Iverson

Faculty Publications

This word experimentally explores sub-boiling pool nucleation on micro-structured superhydrophobic surfaces. All surfaces tested were submerged in a 20 mm deep pool of water and heated from below to maintain a constant surface temperature, while the side walls of the pool were insulated, and the top was covered. Three thermocouples positioned in the pool obtain the average pool temperature. A heat flux sensor is placed directly beneath the surface to measure the heat flux supplied to the pool. Free convection heat transfer coefficients are obtained for the sub-boiling temperature range of 40 – 90 ºC. Six surface types are studied: …

Ignition And Extinction Behavior Of Fuels In A Microcombustor, Pawan Sharma

LSU Doctoral Dissertations

Conventional fuel testing device-CFR engine requires large quantities of fuels, which makes it unsuitable for research of small samples of fuels. This current study seeks to address this limitation by using an externally heated microcombustor as an alternative fuel testing device. Mainly three combustion behaviors have been observed inside a microcombustor: strong flames at higher flow rates, Flames with Repetitive Extinction and Ignition (FREI) at intermediate flow rates, and weak flames at marginal flow rates. In previous studies, weak combustion behavior has been proven suitable to study fuel properties from small samples of fuels. Microcombustor experiments typically rely on flame …

Numerical Study On The Dynamic Process Of Single Plume Flow In Thermal Convection With Polymers, Jian-Ping Cheng, Wei-Hua Cai, Hong-Na Zhang, Feng-Chen Li, Lian Shen, Shi-Zhi Qian

Mechanical & Aerospace Engineering Faculty Publications

A direct numerical simulation of single plume flow in thermal convection with polymers was carried out in a domain with 1:3 as the width to height ratio. The heat transport ability is weakened by adding polymers within the here-investigated governing parameter range. However, it is promoted when the maximum polymer extension L is increased. The distribution of vertical velocity and temperature indicates that the plume in the polymer solution case is speeded up and widens bigger as compared to that in the Newtonian fluid case. Inside the plume, polymer chains tend to release energy at the position where the …

Liquid-To-Liquid Low Grade Waste Heat Recovery Using A Two-Channel Loop, Waleed Farwana

Masters Theses

The use of thermoelectric generators (TEGs) for producing electric energy from low grade “waste heat” has been theorized to provide a sustainable and low-cost energy source for electric power plants. The purpose of this study is to model and experimentally validate a TEG device that takes advantage of low grade waste heat (approximately 100-150 degrees Celsius) in liquid form in order to generate power that can be used for various applications in the surrounding environment. This research aims to demonstrate that optimized TEG designs bear the potential to compete with other methods of low grade waste heat energy harvesting in …

Optimization Of The Practice Of Slow Cooling Steel Bars: A Redesign And Modernization Of Materials, Eryn Johnston

Mechanical Engineering Undergraduate Honors Theses

Throughout the process of steel making, certain grades of steel are a higher risk for defects caused by the inability to quickly diffuse hydrogen through the steel when cooled to room temperature at a normal rate based on the ambient air temperature. To reduce the hydrogen flaking defects that are caused due to hydrogen entrapment in the steel, the process of slow cooling is utilized. This process reduces the cooling rate of steel bars by keeping them at a higher temperature for extended periods and in turn gives the hydrogen a chance to fully dissipate from the steel. In many …

Investigations Into The Airside Cooling Of A Heat Exchanger, David Vallet

UNLV Theses, Dissertations, Professional Papers, and Capstones

In this study we investigate the air-side cooling of a flat-plate fin and tube heat transfer condenser with numerical simulations. A new design is proposed which utilises vortex generators to direct the flow in such a way as to remove some of the stagnant heated air that collects in the wake of the pipes. A comparative study of the proposed design and a standard tube and fin condenser is conducted by varying the air side entrance velocities. The Shear Stress Tension, SST $\kappa - \omega$ 2-equation turbulent model is used to solve the RANS model in ANSYS Fluent 18. The …

Selecting The Most Effective Energy Modeling Tool Based On A Project Requirement, Sodiq Akande

Electronic Theses and Dissertations

Building energy usage can be derived and controlled by performing building energy modeling. BEM can be performed using numerous software tools such as DesignBuilder, OpenStudio, EnergyPlus etc. These modeling tools can be sorted into three different modeling categories: Black-box, Gray-box and White-box. It is important for a modeler to be able to quickly select the proper tool from the proper category to meet the need of the project. To validate the method of categorizing tools, the three models generated using tools from each category and the modeling outputs required were compared. Each model was designed to estimate the amount of …

Heat Flow Characterization Of Speakers, Sabrina M. Gough, Lydia K. Hedge, Nicolas M. Jones

Mechanical Engineering

Statement of Confidentiality: The complete senior project report was submitted to the project advisor and sponsor. The results of this project are of a confidential nature and will not be published at this time.

Bubble Nucleation In Superhydrophobic Microchannels Due To Subcritical Heating, Adam Cowley, Daniel Maynes, Julie Crockett, Brian D. Iverson

Faculty Publications

This work experimentally studies the effects of single wall heating on laminar flow in a high-aspect ratio superhydrophobic microchannel. When water that is saturated with air is used as the working liquid, the non-wetted cavities on the superhydrophobic surfaces act as nucleation sites and allow air to effervesce out of the water and onto the surface when heated. Previous works in the literature have only considered the opposite case where the water is undersaturated and absorbs air out the cavities for a microchannel setting. The microchannel considered in this work consists of a rib/cavity structured superhydrophobic surface and a glass …

Numerical Simulation Of Heat Transfer And Chemistry In The Wake Behind A Hypersonic Slender Body At Angle Of Attack, Matthew J. Satchell, Jeffrey M. Layng, Robert B. Greendyke

Faculty Publications

The effect of thermal and chemical boundary conditions on the structure and chemical composition of the wake behind a 3D Mach 7 sphere-cone at an angle of attack of 5 degrees and an altitude of roughly 30,000 m is explored. A special emphasis is placed on determining the number density of chemical species which might lead to detection via the electromagnetic spectrum. The use of non-ablating cold-wall, adiabatic, and radiative equilibrium wall boundary conditions are used to simulate extremes in potential thermal protection system designs. Non-ablating, as well as an ablating boundary condition using the “steady-state ablation” assumption to compute …

Optimization Of Heat Sinks In A Range Of Configurations., Archibald Allswell Amoako

Electronic Theses and Dissertations

In this study, different heatsink geometries used for electronic cooling are studied and compared to each other to determine the most efficient. The goal is to optimize heat transfer of the heat sinks studied in a range of configuration based on fin geometry. Heat sinks are thermal conductive material devices designed to absorb and disperse heat from high-temperature objects (e.g. Computer CPU). Common materials used in the manufacturing of heat sinks are aluminum and copper due to their relatively high thermal conductivity and lightweight [1]. Aluminum is used as the material for the heatsinks studied in this research project. To …

Development And Thermal Management Of A Dynamically Efficient, Transient High Energy Pulse System Model, Nathaniel J. Butt

Browse all Theses and Dissertations

As technology advances, the abilities of civilian and military vehicles, both air and ground, will undoubtedly increase as well. One of the main areas of improvement is in the electronics area. The new electronics are ever smaller, use ever higher amounts of electrical power, and require ever smaller temperature tolerances. This leads to the problem of effectively managing the increasing thermal loads and temperature tolerances on these systems. One electronic system that causes concern is a high energy pulse system (HEPS). These devices have very high thermal loads (100s of kW). On an air vehicle, where thermal management by legacy …

Design And Analysis Of Compressed Air Power Harvesting Systems, Zachary James Sadler

Theses and Dissertations

Procedure for site discovery, system design, and optimization of power harvesting systems is developed with an emphasis on application to air compressors. Limitations for the usage of infrared pyrometers is evaluated. A system of governing equations for thermoelectric generators is developed. A solution method for solving the system of equations is created in order to predict power output from the device. Payback analysis is proposed for determining economic viability. A genetic algorithm is used to optimize the power harvesting system payback with changing quantities and varieties of thermoelectric generators, as well as the back work put into cooling the thermoelectric …

Design And Validation Of An Experimental Setup To Study Single Phase Heat Transfer Enhancement Of Femtosecond Laser Processed Metallic Surfaces, Sarah Jane Wallis

Department of Mechanical and Materials Engineering: Dissertations, Theses, and Student Research

In the present work, a single phase flow heat transfer experimental loop was designed with the intention of studying the effects of femtosecond laser surface processing (FLSP) on metallic surfaces with the specific goal of enhancing heat transfer in compact heat exchangers currently in use by NASA. This experimental setup went through two major design iterations which are detailed in this thesis. The first iteration consisted of a counterflow fluid-to-fluid heat exchanger, which measured overall heat transfer coefficients and pressure drops, where the overall heat transfer coefficient is defined in terms of the total thermal resistance to heat transfer between …

Hydrodynamic And Thermal Effects Of Sub-Critical Heating On Superhydrophobic Surfaces And Microchannels, Adam M. Cowley

Theses and Dissertations

This dissertation focuses on the effects of heating on superhydrophobic (SHPo) surfaces. The work is divided into two main categories: heat transfer without mass transfer and heat transfer in conjunction with mass transfer. Numerical methods are used to explore the prior while experimental methods are utilized for the latter. The numerical work explores convective heat transfer in SHPo parallel plate microchannels and is separated into two stand-alone chapters that have been published archivally. The first considers surfaces with a rib/cavity structure and the second considers surfaces patterned with a square lattice of square posts. Laminar, fully developed, steady flow with …

Construction Of Metallic Glass Structures By Laser-Foil-Printing Technology, Yiyu Shen, Yingqi Li, Hai-Lung Tsai

Mechanical and Aerospace Engineering Faculty Research & Creative Works

Metallic glasses (MGs) have superior mechanical properties such as high tensile strength, hardness, and corrosion resistance, as compared to crystalline metals. Although newly developed MGs have significantly reduced critical cooling rates down to 10 K/s, products of MGs are still limited to simple geometries such as foils/plates or rods with thin section-thickness which is mainly caused by the decrease of thermal conductivities of the new MGs. Recently, we developed a new Laser-foil-printing (LFP) additive manufacturing technology which welds foils, layer by layer, to construct desired 3D structures. With the LFP and Zr-based amorphous foils, 3D, large amorphous structures with complex …

Thermal Measurement And Optimization Of Materials And Processes In A Li-Ion Cell, Vivek Vishwakarma

Mechanical and Aerospace Engineering Dissertations - Archive

Applications of Lithium-ion cells range from consumer electronics to electric cars because of their excellent electrochemical performance and energy density. However, a Li-ion cell also suffers from poor thermal transport characteristics, which reduces performance, causes overheating and thermal runaway. This work contributes towards thermal characterization of key Li-ion battery materials and identifies and improves the rate-limiting, material-level thermal conduction process in a Li-ion cell. Among the various materials within a Li-ion cell, the separator is expected to have the lowest thermal conductivity. In this work, we have carried out first-ever measurements of thermal conductivity and heat capacity of the separator …

Hysteresis Heating Of Railroad Bearing Thermoplastic Elastomer Suspension Element, Oscar O. Rodriguez, Arturo A. Fuentes, Constantine Tarawneh, Robert E. Jones

Mechanical Engineering Faculty Publications

Thermoplastic elastomers (TPE’s) are increasingly being used in rail service in load damping applications. They are superior to traditional elastomers primarily in their ease of fabrication. Like traditional elastomers they offer benefits including reduction in noise emissions and improved wear resistance in metal components that are in contact with such parts in the railcar suspension system. However, viscoelastic materials, such as the railroad bearing thermoplastic elastomer suspension element (or elastomeric pad), are known to develop self-heating (hysteresis) under cyclic loading, which can lead to undesirable consequences. Quantifying the hysteresis heating of the pad during operation is therefore essential to predict …

Conjugate Heat Transfer And Thermo-Structural Analysis Of The Actively Cooled Multi-Stage Conical Nozzle And Hypersonic Low-Reynolds Diffuser Of The New Arc-Heated Wind Tunnel (Awht-Ii) Of The University Of Texas At Arlington, David Ray Campbell

Mechanical and Aerospace Engineering Theses - Archive

Arc-heated wind tunnels are the primary test facility for screening and qualification of candidate materials for hypersonic thermal protection systems (TPS). Via an electric arc that largely augments the enthalpy (by tens of MJ/kg) of the working fluid (Air, Nitrogen, CO2 in case of Mars-entry studies) passed through a converging-diverging nozzle at specific stagnation conditions, different regimes encountered in entry and re-entry hypersonic aerothermodynamics can be simulated. Because of the high-enthalpies (and associated temperatures that generally exceed the limits required by the thermo-structural integrity of the facility) the active cooling of the arc-heated wind tunnel’s parts exposed to the working …

Origami: Numerical Solutions Of Apparent Absorptivity In Origami Folds, Michael Farnsworth, Brian Iverson

Journal of Undergraduate Research

There are three major types of heat transfer: conduction, convection, and radiation. In many cases, radiation is ignored due to the fact that the amount of heat transferred by this method tend to be small compared to conduction and convection. However, in space and in some settings on earth, radiation is dominant and important. Absorptivity is a measure of an object’s ability to absorb radiation, and apparent absorptivity is a measure of how the shape of an object affects the amount of radiation that it absorbs. For example, if you were to shine a flashlight on a mirror, the light …

Modeling And Computation Of The Maximum Braking Energy Speed For Transport Category Airplanes, Nihad E. Daidzic

Journal of Aviation Technology and Engineering

Transport-category or FAR/CS 25 certified airplanes may occasionally become braking energy capacity limited. Such limitation may exist when heavy airplanes are departing airports at high-density altitudes, on relatively long runways, and/or possibly with some tailwind component. A maximum braking energy VMBE speed exists which may limit the maximum allowable takeoff decision/action speed V1. The ever-existing possibility of high-speed rejected takeoff in such conditions may also limit the airplane gross weight for declared available distances. To gain deeper insights and acquire better understanding of the topic, a theoretical model of the maximum braking energy and the related VMBE speed for T-category …

Shape Optimization Of Helical Coil Tube For Maximizing Heat Transfer, Venkat Manoj Kandukuri

Mechanical and Aerospace Engineering Theses - Archive

Many researchers have observed the enhancement of heat transfer in coiled tubes compared to straight tubes with the same diameter and length. It is known fact, that in a helical coil tube the maximum axial velocity shifted towards the outer wall of the pipe and imbalance between centrifugal forces and inertial loads to a secondary motion of the fluid in the cross-section of the tube. This secondary motion is responsible for improved transport of heat energy to/from the tube walls. Previous conducted Experimental and computational parametric studies show the relationship between the increased heat transfer and parameters such as pitch, …

Thermal Transport In Lithium Ion Batteries: An Experimental Investigation Of Interfaces And Granular Materials, Aalok Jaisheela Uday Gaitonde

Open Access Theses

Increasing usage and recent accidents due to lithium-ion (Li-ion) batteries exploding or catching on fire has inspired research on the characterization and thermal management of these batteries. In cylindrical 18650 cells, heat generated during the battery's charge/discharge cycle is poorly dissipated to the surrounding through its metallic case due to the poor thermal conductivity of the jelly roll, which is spirally wound with many interfaces between electrodes and the polymeric separator. This work presents a technique to measure the thermal conduction across the metallic case-plastic separator interface, which ultimately limits heat transfer out of the jelly roll.

The polymeric separator …

Thermo-Mechanical System Identification Of A Shape Memory Alloy Actuated Mechanism, Cody Alexander Wright

Mechanical & Aerospace Engineering Theses & Dissertations

Shape memory alloy (SMA) actuators paired in an antagonistic arrangement can be used to produce mechanisms that replicate human biomechanics. To investigate this proposal, the biomechanical articulation of the elbow by means of the biceps brachii muscle is compared with that of a SMA actuated arm. This is accomplished by parametric analysis of a crank-slider kinematic mechanism actuated, first, with an experimentally characterized SMA wire and then an idealized musculotendon actuator based on actuation properties of muscles published in the literature. Next, equations of motion for the system dynamics of the SMA actuated mechanism are derived and phase portrait analysis …

Evaluation Of The Impact Of Slab Foundation Heat Transfer On Heating And Cooling In Florida, Florida Solar Energy Center, Danny Parker

FSEC Energy Research Center®

The U.S. Department of Energy's Building America Partnership for Improved Residential Construction (BA-PIRC) performed experiments in the Florida Solar Energy Center's Flexible Residential Test Facility intended to assess for the first time (1) how slab-on-grade construction influences interior cooling in a cooling-dominated climate and (2) how the difference in a carpeted versus uncarpeted building might influence heating and cooling energy use.