Mechanical Engineering Commons^™

Cavitation In Pharmaceutical Manufacturing And Shipping, Donn Sederstrom

Electronic Theses and Dissertations

Therapeutic proteins are used to successfully treat hemophilia, Crohn's Disease, diabetes, and cancer. Recent product recalls have occurred because of sub-visible particle formation resulting from the inherent instability of proteins. It has been suggested that particle formation is associated with late stage processing steps of filling, shipping, and delivery. Previous work at the University of Denver demonstrated that fluid cavitation can generate a large number of sub-visible protein particles in ultra clean formulations, but that mitigation can be achieved with fluid property manipulation. The goal of this research was to (1) assess the risk of cavitation under common pharmaceutical manufacturing …

Methods For Identifying Acoustic Emissions From The Front Face Of A Small Piezoelectric Blower, Brad K. Solomon

Theses and Dissertations

This thesis focuses on identifying acoustic noise generating components in piezoelectric blowers through transverse velocity measurements and the development of a numerical fluid model. Piezoelectric ceramics have proven useful for many industries and areas of research involving: high precision actuators, noise control, ultrasonic devices, and many other areas. As of late, a unique adaptation of piezoelectric ceramics is surfacing in the area of pumping and cooling. Air pumps that use these ceramics replace the traditional electric motor, resulting in lower power consumption, less moving parts, constant pressure gradients, lower overall weight, and a low profile. The current drawback of this …

Design And Simulation Of Passive Thermal Management System For Lithium-Ion Battery Packs On An Unmanned Ground Vehicle, Kevin Kenneth Parsons

Master's Theses

The transient thermal response of a 15-cell, 48 volt, lithium-ion battery pack for an unmanned ground vehicle was simulated with ANSYS Fluent. Heat generation rates and specific heat capacity of a single cell were experimentally measured and used as input to the thermal model. A heat generation load was applied to each battery and natural convection film boundary conditions were applied to the exterior of the enclosure. The buoyancy-driven natural convection inside the enclosure was modeled along with the radiation heat transfer between internal components. The maximum temperature of the batteries reached 65.6 °C after 630 seconds of usage …

The Extraction Of Shock Waves And Separation And Attachment Lines From Computational Fluid Dynamics Simulations Using Subjective Logic, Matthew C. Lively

Theses and Dissertations

The advancement of computational fluid dynamics to simulate highly complex fluid flow situations have allowed for simulations that require weeks of computation using expensive high performance clusters. These simulations often generate terabytes of data and hinder the design process by greatly increasing the post-processing time. This research discusses a method to extract shock waves and separation and attachment lines as the simulation is calculating and as a post-processing step. Software agents governed by subjective logic were used to make decisions about extracted features in converging and converged data sets. Two different extraction algorithms were incorporated for shock waves and separation …

Simulation Of Counterintuitive Pressure Drop In A Parallel Flow Design For A Specimen Basket For Use In The Advanced Test Reactor, Adam X. Zabriskie

All Graduate Theses and Dissertations, Spring 1920 to Summer 2023

To continue improving nuclear energy, new materials must be tested in testing reactors such as the Advanced Test Reactor (ATR) at Idaho National Laboratory. A new test cap section allowed coolant to contact specimens tested in the ATR. A parallel channel test cap section should reduce the pressure drop across this section compared to a single channel. A fluid experiment conducted by Idaho State University showed the pressure drop was actually greater. A Computation Fluid Dynamics simulation using STAR-CCM+ was conducted of the fluid experiment to explain the abnormal pressure drop. The simulation provided evidence of ow through the test …

Computational Fluid Dynamics Analysis Of Butterfly Valve Performance Factors, Adam Del Toro

All Graduate Theses and Dissertations, Spring 1920 to Summer 2023

Butterfly valves are commonly used to control fluid flow inside of piping systems. A butterfly valve typically consists of a metal disc formed around a central shaft, which acts as its axis of rotation. As a butterfly valve is rotated open, fluid is able to more readily flow past the valve. A butterfly valve’s design is important to understand and is commonly characterized by its own performance factors. How a butterfly valve will perform, while in operation at different opening angles and under different types of flow, is critical information for individuals planning and installing piping systems involving the valve. …

Vortex Shedding Dynamics In Long Aspect-Ratio Aerodynamics Bodies, Liu Chen

Dissertations, Master's Theses and Master's Reports - Open

The focus of the current dissertation is to study qualitatively the underlying physics of vortex-shedding and wake dynamics in long aspect-ratio aerodynamics in incompressible viscous flow through the use of the KLE method. We carried out a long series of numerical experiments in the cases of flow around the cylinder at low Reynolds numbers. The study of flow at low Reynolds numbers provides an insight in the fluid physics and also plays a critical role when applying to stalled turbine rotors. Many of the conclusions about the qualitative nature of the physical mechanisms characterizing vortex formation, shedding and further interaction …

Feature-Based Neuro-Symbolic Networks For Global Diagnostics, Tracy Lynn Schantz

Electronic Theses and Dissertations

Engineered system diagnostics have been researched over the years with many successful results. From transportation systems to office technologies, many have been equipped with self-diagnostic capabilities and are called Smart Machines. In spite of these advances, current diagnostic systems are driven by direct sensory information without much concern for patterns of the system behavior or features associated with them. For large-scale systems with complex dynamics, global as well as local diagnostics become of great importance, where sensory information is used as input for the local diagnostics, and patterns of behavior or features are utilized for global diagnostics.

The main objective …

Numerical Simulation Of Buoyancy-Driven Turbulent Ventilation In Attic Space Under Winter Conditions, Shimin Wang, Zhigang Shen, Linxia Gu

Department of Mechanical and Materials Engineering: Faculty Publications

Attic design and construction have significant impacts on residential buildings’ energy performance. In order to understand how passive ventilation rates affect ridge-vent attic’s performance, a two-dimensional steady-state finite volume model is employed to simulate the buoyancy-driven turbulent ventilation and heat transfer in a triangular attic space of a gable-roof residential building under winter conditions. The modeled attic has a pitch of 5/12 and a passive ventilation system, consisting of continuous ridge and soffit vents. The v2f model is used to analyze the turbulent air flow and natural convection heat transfer inside the attic. The effects of ambient air temperature, vent …

Computational Investigation Of Ethanol And Bifuel Feasibility In Solstice Engine, Adam Michael Blake

Browse all Theses and Dissertations

A Gasoline Direct Injection (GDI) engine enables an increased fuel efficiency and higher power output than a conventional Port Fuel Injection (PFI) system. By injecting pressurized fuel straight into each cylinder of an internal-combustion engine, the degree of fuel atomization is increased, as well as the fuel vaporization rate. In order to further harness the effects of direct injection, ethanol is implemented as a fuel. The cooling effect of ethanol fuel droplets changing to vapor inside the combustion chamber facilitates a higher compression ratio, thus increasing engine power and efficiency. Three dimensional computational simulation is used to investigate the feasibility …

Simulation Of Whistle Noise Using Computational Fluid Dynamics And Acoustic Finite Element Simulation, Jiawei Liu

Theses and Dissertations--Mechanical and Aerospace Engineering

The prediction of sound generated from fluid flow has always been a difficult subject due to the nonlinearities in the governing equations. However, flow noise can now be simulated with the help of modern computation techniques and super computers. The research presented in this thesis uses the computational fluid dynamics (CFD) and the acoustic finite element method (FEM) in order to simulate the whistle noise caused by vortex shedding. The acoustic results were compared to both analytical solutions and experimental results to better understand the effects of turbulence models, fluid compressibility, and wall boundary meshes on the acoustic frequency response. …

Assessments And Computational Simulations In Support Of A Time-Varying Mass Flow Rate Measurement Technique For Pulsatile Gas Flow, Andrew Rice

Dissertations, Master's Theses and Master's Reports - Open

This thesis covers the correction, and verification, development, and implementation of a computational fluid dynamics (CFD) model for an orifice plate meter. Past results were corrected and further expanded on with compressibility effects of acoustic waves being taken into account. One dynamic pressure difference transducer measures the time-varying differential pressure across the orifice meter. A dynamic absolute pressure measurement is also taken at the inlet of the orifice meter, along with a suitable temperature measurement of the mean flow gas. Together these three measurements allow for an incompressible CFD simulation (using a well-tested and robust model) for the cross-section independent …

Computational Study On Micro-Pilot Flame Ignition Strategy For A Direct Injection Stratified Charge Rotary Engine, Zachary Steven Votaw

Browse all Theses and Dissertations

The Office of Security of Defense's Assured Fuels Initiative has recently been pressing for a single fuel battle space. This endeavor requires modifying many of the vehicle power plants currently in operation throughout the Armed Forces. The RQ-7 Shadow, an unmanned aerial vehicle (UAV) utilized by the Marine Corp and Army for reconnaissance purposes, is powered by UEL's AR741 rotary engine and functions on aviation fuel. One effort underway has been focused on developing this rotary engine system to operate on heavy fuels using direct injection technology and charge stratification. Although the rotary engine has many advantages over standard reciprocating …

Port Flow Test System, Daniel Chairez, Chelsea E. Crawford, Daniel S. Welch

Mechanical Engineering

Solar Turbines Gas Compressor Engineering Division of San Diego, California called upon the Mechanical Engineering students of California Polytechnic University, San Luis Obispo to provide recommendations for optimization of compressor end cap port design. Various sizes of compressors have end caps with numerous ports that exchange fluids between the inside and outside of the working fluid pressure vessel. Because so many ports must exist on the end caps, unusual flow paths are created to supply the appropriate location within the compressor. These flow paths commonly consist of a drilled inlet hole which intersects with a sudden expansion. The sudden expansion …

Cfd Simulations For The Effect Of Unsteady Wakes On The Boundary Layer Of A Highly Loaded Low Pressure Turbine Airfoil (L1a), Samuel J. Vinci

ETD Archive

The study of a very high lift, low-pressure turbine airfoil in the presence of unsteady wakes was performed computationally and compared against experimental results. The experimental data were collected in a low speed wind tunnel under high (4.9 ) and then low (0.6 ) freestream turbulence intensity conditions on a linear cascade with wakes that were produced from moving rods upstream of the cascade. The flow coefficient was kept at 0.7 while the rod to blade spacing was changed from 1 to 1.6 to 2 blade spacings. These cases were conducted for Reynolds number equal to 25,000 and 50,000, based …

An Implicit High-Order Spectral Difference Method For The Compressible Navier-Stokes Equations Using Adaptive Polynomial Refinement, Caleb J. Barnes

Browse all Theses and Dissertations

A high/variable-order numerical simulation procedure for gas dynamics problems was developed to model steep grading physical phenomena. Higher order resolution was achieved using an orthogonal polynomial Gauss-Lobatto grid, adaptive polynomial refinement and artificial diffusion activated by a pressure switch. The method is designed to be computationally stable, accurate, and capable of resolving discontinuities and steep gradients without the use of one-sided reconstructions or reducing to low-order. Solutions to several benchmark gas-dynamics problems were produced including a shock-tube and a shock-entropy wave interaction. The scheme's 1st-order solution was validated in comparison to a 1st-order Roe scheme solution. Higher-order solutions were shown …

Design And Scale-Up Of Production Scale Stirred Tank Fermentors, Ryan Z. Davis

All Graduate Theses and Dissertations, Spring 1920 to Summer 2023

In the bio/pharmaceutical industry, fermentation is extremely important in pharmaceutical development, and in microbial research. However, new fermentor designs are needed to improve production and reduce costs of complex systems such as cultivation of mammalian cells and genetically engineered micro-organisms. Traditionally, stirred tank design is driven by the oxygen transfer capability needed to achieve cell growth. However, design methodologies available for stirred tank fermentors are insufficient and many times contain errors. The aim of this research is to improve the design of production scale stirred tank fermentors through the development of dimensionless correlations and by providing information on aspects of …

A Computational Study For The Utilization Of Jet Pulsations In Gas Turbine Film Cooling And Flow Control, Olga V. Kartuzova

ETD Archive

Jets have been utilized in various turbomachinery applications in order to improve gas turbines performance. Jet pulsation is a promising technique because of the reduction in the amount of air removed from compressor, which helps to increase turbine efficiency. In this work two areas of pulsed jets applications were investigated, first one is film cooling of High Pressure Turbine (HPT) blades and second one is flow separation control over Low Pressure Turbine (LPT) airfoil using Vortex Generator Jets (VGJ) The inlet temperature to the HPT significantly affects the performance of the gas turbine. Film cooling is one of the most …

Transitional Flow Prediction Of A Compressor Airfoil, Vivek Hariharan

University of Kentucky Master's Theses

The steady flow aerodynamics of a cascade of compressor airfoils is computed using a two-dimensional thin layer Navier-Stokes flow solver. The Dhawan and Narasimha transition model and Mayle‟s transition length model were implemented in this flow solver so that transition from laminar to turbulent flow could be included in the computations. A method to speed up the convergence of the fully turbulent calculations has been introduced. In addition, the effect of turbulence production formulations and including streamline curvature correction in the Spalart-Allmaras turbulence model on the transition calculations is studied. These transitional calculations are correlated with the low and high …

Computational Study Of Fluid-Valve Interaction Involving Deep Vein Thrombosis, Upendra Parimi

Open Access Theses & Dissertations

The venous valves in veins carry on the important function of eliminating the retrograde (re-verse) flow of blood in veins and help the veins to carry on their work effectively. The abnormal functioning of venous valves can cause deep vein thrombosis (DVT) which is a phenomena caused by clotting in deep veins. The importance of the thesis work lies in understanding the role of blood flow dynamics in Deep Vein Thrombosis (DVT). Elderly People and pregnant women are the ones who are most likely to develop DVT. It was determined from previous studies that women in their postpartum period are …

Designing Of Energy Efficient Indoor Environments Using A Localized Radial Basis Function Meshless Method, Victor Huayamave

Electronic Theses and Dissertations

Around the world, the energy over consumption issue has been one of the key socio-economic and political challenges, which has drastically worsened over the last few years. Over the years engineers and environmentalists have proposed several approaches to improve energy efficiency. One is to reduce energy demand by improving consumption habits and a second approach is to introduce the use of a "greener" concept by using biomaterials in a diverse and more efficient manner in engineering construction to create energy efficient environments. This work will investigate the effects of using "green" stabilized earth materials to provide and enhance thermal regulation …

Parallelization Of Performance Limiting Routines In The Computational Fluid Dynamics General Notation System Library, Kyle Horne

All Graduate Theses and Dissertations, Spring 1920 to Summer 2023

The Computational Fluid Dynamics General Notation System provides a unified way in which computational fluid dynamics data can be stored, but does not support the parallel I/O capabilities now available from version five of the Hierarchical Data Format library which serves as a back end for he standard. To resolve this deficiency, a new parallel extension library has been written and benchmarked for this work which can write files compliant with the standard using parallel file access modes. When using this new library, the write performance shows an increase of four-fold in some cases when compared to the same hardware …

Demonstration Of A Completely Described Swirling Jet Experiment Used For Numerical Validation, Brandon M. Wilson

All Graduate Theses and Dissertations, Spring 1920 to Summer 2023

This thesis demonstrates the standard for the design of an experimental model to be used for numerical validation purposes. It is proposed that numerical models may be assessed more accurately and directly by validation with a completely described experimental model, consisting of accurate descriptions of the operating conditions, fluid properties, and experimental uncertainties. This idea is demonstrated using an experimental model of a swirling jet at three Reynolds numbers (Re = 550, 2560, and 3650), with vortex breakdown existing in the higher two Reynolds number cases. Measurements of the swirling jet were obtained at two locations upstream of the jet …

Employing The Spectral Collocation Method In The Modeling Of Laminar Tube Flow Dynamics, Corey Michael Thibeault

All Graduate Theses, Dissertations, and Other Capstone Projects

The spectral collocation method is a numerical approximation technique that seeks the solution of a differential equation using a finite series of infinitely differentiable basis functions. This inherently global technique enjoys an exponential rate of convergence and has proven to be extremely effective in computational fluid dynamics. This paper presents a basic review of the spectral collocation method. The derivation is driven with an example of the approximation to the solution of a 1D Helmholtz equation. A Matlab code modeling two fluid dynamics problems is then given. First, the classic two-dimensional Graetz problem is simulated and compared to an analytical …

Experimental And Numerical Study Of A Proton Exchange Membrane Electrolyzer For Hydrogen Production, Sachin S. Deshmukh

UNLV Theses, Dissertations, Professional Papers, and Capstones

Hydrogen as a fuel source has received attention from researchers globally due to its potential to replace fossil based fuels for energy production. Research is being performed on hydrogen production, storage and utilization methods to make its use economically feasible relative to current energy sources. The PEM electrolyzer is used to produce hydrogen and oxygen using water and electricity. Focus of our study is to provide a benchmark experiment and numerical model of a single cell electrolyzer that can assist in improving the current state of understanding of this system. Parametric analysis of an experimental cell was performed to understand …

Measurements And Modeling Of Coal Ash Deposition In An Entrained-Flow Reactor, Ryan P. Blanchard

Theses and Dissertations

Coal plays a significant role in meeting the world's need for energy and will continue to do so for many years to come. Economic, environmental, and public opinion are requiring coal derived energy to be cleaner and operate in a more narrow window of operating conditions. Fouling and slagging of heat transfer surfaces continues to be a challenge for maintaining boiler availability and expanding the use of available fuels and operating conditions. The work incorporates existing information in the literature on ash deposition into a User-Defined Function (UDF) for a commercial comprehensive combustion and CFD code. Results from the new …

Parametric Optimization Design System For A Fluid Domain Assembly, Matthew Jackson Fisher

Theses and Dissertations

Automated solid modeling, integrated with computational fluid dynamics (CFD) and optimization of a 3D jet turbine engine has never been accomplished. This is due mainly to the computational power required, and the lack of associative parametric modeling tools and techniques necessary to adjust and optimize the design. As an example, the fluid domain of a simple household fan with three blades may contain 500,000 elements per blade passage. Therefore, a complete turbine engine that includes many stages, with sets of thirty or more blades each, will have hundreds of millions of elements. The fluid domains associated with each blade creates …

An Investigation Into Fuel Cells And Flow Cytometers Optimal Design, Etim Sunday Udoetok

LSU Doctoral Dissertations

The aim of the fuel cells part of this project was to investigate the performance of Proton Exchange Membrane Fuel Cells and closely related fuel cell types like the Alkaline Fuel Cells and Phosphoric Acid Fuel Cells. The investigation involved understanding the performance of fuel cells, addressing the shortcomings of currently used designs, and finding new methods for improving the performance of fuel cells. CFD was used to study flow channels and information learned from the study was used to design a new and improved flow channel. A prototype of the new design was fabricated, tested and found to perform …

Incorporating Computational Fluid Dynamics Into The Preliminary Design Cycle, Jonathan Knighton Shelley

Theses and Dissertations

Industry is constantly looking for ways to bring new or derivative products to market in the shortest amount of time for the least amount of money. To accomplish this, Industry has adopted Computer Aided Engineering (CAX) tools that perform structural, flow, manufacturing, and cost analysis. The way in which a company utilizes these CAX tools can determine the success of these new products. One of these tools that Industry often struggles with in the preliminary design of a product is Computational Fluid Dynamics (CFD). Some of the challenges presented by CFD are the time it takes to create a CAD …

A Cad-Centric Approach To Cfd Analysis With Discrete Features, Matthew Lee King

Theses and Dissertations

During the conceptual design stage several concepts are generated, and a few are selected for detailed analyses. CAD models from conceptual design often follow the "over-the-wall" approach for downstream analyses such as FEA, CFD, heat transfer, and vibrations. A CAD-centric approach will be applied to the CAD-to-CFD process to help industry in an ongoing quest to shorten the design cycle time. The CAD-centric approach consists of using the CAD model as a source of data for downstream applications such as mesh generation, and CFD setup. The CAD model used in the CAD-centric approach contains the geometry to be analyzed and …