Mechanical Engineering Commons^™

Forcespinning®: An Alternative Method To Fabricate Metal Oxide/Carbon Composite Nanofiber Anodes For Li-Ion Batteries, Luis Zuniga

Theses and Dissertations

Metals and their respective oxides have been highly regarded as next generation anode materials for lithium-ion batteries (LIBs). In this research work the electrochemical performance of Sn, SnO2, and TiO2. With the advantages of nanotechnology and the Forcespinning® method of fabricating micro and nanofibers, binder-free anodes are produced from metal or metal oxide/carbon composite microfibers. Through these microfibers the electrochemical performance of the above mentioned materials are significantly improved due to the increased surface area per volume providing a large number of reaction sites for the anode materials. Further performance enhancement was achieved by also modifying the fiber microstructure to …

Wettability Of Nonwoven Polymeric Nanofiber Mats, Edgar Munoz

Theses and Dissertations

The wettability of heterogeneous materials has been attracting special interest by academia and industrial sector given the need to development self-cleaning Nonwoven nanofiber mats have demonstrated potential given its hydrophobicity granted by the ultimate structure of the system, small fiber diameter and small pores giving rise to effects such as the Cassie-Baxter. This thesis analyzed the wettability of a wide range of polymeric systems. Nanofiber mats were manufactured using the Forcespinning® technology. Samples were prepared at different polymeric concentrations and rotational speeds to alter fiber size; density of the mat was also altered to evaluate the effect of porosity on …

Optimizing Border Security With Stochastic And Deterministic Strategies, Gabriel A. Rueda

Theses and Dissertations

International trade and border security have always been linked together, and so has the need to find ways to improve security decisions. The United States and bordering countries benefit from the North American Free Trade Agreement (NAFTA), but amongst the positive effects of NAFTA there is a looming drug threat that effects the bi-national supply chains. In 2015 Customs and Border Protections (CBP) processed over 72,000 trucks, rail, and sea containers a day. CBP also seized 3.4 million pounds of narcotics, the majority of them at the ports of entry. With unknown threats using commercial vehicles to transport their illicit …

Knee Joint Internal Forces During Squat Jump Exercise, Ricardo Moreno

Theses and Dissertations

The purpose of this research is to investigate muscular ligament and joint contact forces produced during squat jump exercise. An inverse dynamics, two dimensional, leg model is used to describe the motion in the sagittal plane. The lower extremity model includes two bones, tibia and femur, tibio-femoral ligaments, and muscles such as quadriceps, hamstrings, and gastrocnemius. The ligaments are anatomically modeled as nonlinear strings, but the femoral condyle is modeled as a circle and the tibial plateau as a straight line. Experimental squat jump exercises are conducted to obtain the ground reaction forces, the angular accelerations, and centroid linear acceleration …

Study Of Selective Laser Remelting Of 316l S.S. To Reduce Roughness On Inclined Surface, Jafar Ghorbani

Theses and Dissertations

Additive manufacturing (AM) technologies are increasingly competing with subtractive methods, and there are promising applications for additive technologies that are hybrid with traditional manufacturing methods. Poor surface roughness of additive manufactured parts continues to be a major challenge especially for advanced functional parts. In this study, effect of processing parameters are evaluated, optimized and verified by using the Box–Behnken design of experiment method. The results, for the first time, reveal that surface remelting has the potential to become a high speed approach for improving the roughness of non-horizontal surface of additive manufactured parts.

Development Of A Fundamental Autonomous Ground Vehicle Cruise Control Using Matlab And Simulink, Luis F. Martinez

Theses and Dissertations

This study presents and describes the development of a fully autonomous vehicle cruise control system covering the vehicle dynamics and control design needed to simulate such system. It encompasses obstacle avoidance, intelligent-and-optimal lane change as well as adaptive behavior. This study offers a comprehensive two-dimensional cruise control with three degrees of freedom and it is designed using active obstacle avoidance controllers. It also includes optimized fuzzy logic for optimal vehicle trajectory and an extensive array of control law methodology. The end work shows a complete simulation run using MATLAB and Simulink.

The Effect Of Process Parameters And Surface Condition On Bond Strength Between Additively Manufactured Components And Polymer Substrates, Bharat Bhushan Chivukula

Graduate Theses and Dissertations

Additive patching is a process in which printers with multiple axes deposit molten material onto a pre-defined surface to form a bond. Studying the effect of surface roughness and process parameters selected for printing auxiliary part on the bond helps in improving the strength of the final component. Particularly, the influence of surface roughness, as established by adhesion theory, has not been evaluated in the framework of additive manufacturing (AM). A full factorial design of experiments with five replications was conducted on two levels and three factors, viz., layer thickness, surface roughness, and raster angle to examine the underlying effects …

Multivariate Calibration Of A Load Sensor For Dynamic And Static Freight Railcar Applications, Dylan Michael Blackwell

Theses and Dissertations

Determination of the load carried by each bearing in a railcar system is crucial to the integrity of the railroad industry. With accurate load measurement, the process of filling a railcar with its specified cargo can be optimized to provide the maximum amount of cargo without exceeding the upper weight limits imposed by the Associations of American Railroads (AAR). An accurate load measurement will additionally make it possible to identify any load imbalance that occurs during periods of travel which result in having a detrimental effect on the health of the bearing. Previous work conducted with a strain-gauge load sensor …

An Experimental Investigation Of Self-Excited Combustion Dynamics In A Single Element Lean Direct Injection (Ldi) Combustor, Rohan M. Gejji

Open Access Dissertations

The management of combustion dynamics in gas turbine combustors has become more challenging as strict NOx/CO emission standards have led to engine operation in a narrow, lean regime. While premixed or partially premixed combustor configurations such as the Lean Premixed Pre-vaporized (LPP), Rich Quench Lean burn (RQL), and Lean Direct Injection (LDI) have shown a potential for reduced NOx emissions, they promote a coupling between acoustics, hydrodynamics and combustion that can lead to combustion instabilities. These couplings can be quite complex, and their detailed understanding is a pre-requisite to any engine development program and for the development of predictive capability …

Modeling Picking On Pharmaceutical Tablets, Shrikant Swaminathan

Open Access Dissertations

Tablets are the most popular solid dosage form in the pharmaceutical industry because they are cheap to manufacture, chemically and mechanically stable and easy to transport and fairly easy to control dosage. Pharmaceutical tableting operations have been around for decades however the process is still not well understood. One of the common problems faced during the production of pharmaceutical tablets by powder compaction is sticking of powder to the punch face, This is known as 'sticking'. A more specialized case of sticking is picking when the powder is pulled away form the compact in the vicinity of debossed features. In …

Particle Modeling Of Non-Equilibrium Field Emission Driven Rf Microplasmas, Siva Sashank Tholeti

Open Access Dissertations

Non-equilibrium microplasmas at atmospheric pressures have been investigated for active flow control, micropropulsion and electronic display applications to name a few. The operational voltages for these microplasmas are on the order of kilovolts. When the electric field at the electrodes reaches GV/m or tens of GV/m either due to reduced interelectrode spacing and surface irregularities or due to carefully designed nanostructures on the electrodes, quantum processes such as field emission and field ionization come into effect. These can potentially reduce the operational voltages of microplasma devices by an order of magnitude. Due to the rarefied and non-equilibrium nature of these …

4d Printing Dielectric Elastomer Actuator Based Soft Robots, Jiyu Cai

Graduate Theses and Dissertations

4D printing is an emerging technology that prints 3D structural smart materials that can respond to external stimuli and change shape over time. 4D printing represents a major manufacturing paradigm shift from single-function static structures to dynamic structures with highly integrated functionalities. Direct printing of dynamic structures can provide great benefits (e.g., design freedom, low material cost) to a wide variety of applications, such as sensors and actuators, and robotics. Soft robotics is a new direction of robotics in which hard and rigid components are replaced by soft and flexible materials to mimic mechanisms that works in living creatures, which …

Improving Fuel Economy During High Load Diesel Engine System Operation Through Valve Train Flexibility, Xueting Lu

Open Access Theses

As emission regulations getting more stringent and the demand for fossil fuel growing, it is crucial to develop advanced technologies for internal combustion engine to lower emissions and fuel.

Strategies such as diesel oxidation catalysts (DOC) for UHC, diesel particulate filters (DPF) for PM, and selective catalytic reduction (SCR) for NOx have been developed and implemented to convert harmful emissions to innocuous species. However, the efficiencies of these after-treatment systems are heavily temperature dependent.

Heavy-duty over-the-road trucks require periodic active diesel particulate filter regeneration to clean the filter of stored particulate matter. These events require sustained temperatures between 500 and …

Performance Analysis, Dynamic Simulation And Control Of Mass-Actuated Airplane, Sukru Akif Erturk

Mechanical and Aerospace Engineering Dissertations - Archive

The control of space, aerial and underwater vehicles requires moment generation mechanisms to change their orientation. In addition to or in place of conventional moment generation actuators, internally moving-mass actuation has been proposed and/or used for such vehicles. The primary principle for mass-actuation is to reposition gravitational force to change the associated moment while the secondary effect may come from the inertial force due to the motion of the masses. Recent development/miniaturization in flight control sensor, computing and actuation, and electric motors and expansion of applications for small UAV (Unmanned Aerial Vehicle) offer a potential for implementation of internal mass-actuation …

Modeling The Impact Of Battery Degradation Within Lifecycle Cost Based Design Optimization Of Heavy-Duty Hybrid Electric Vehicles, Ashish P. Vora

Open Access Dissertations

The optimal design of hybrid electric vehicle (HEV) powertrains from a systems perspective is critical to realize the maximum benefits for a given application. This is particularly true in the heavy-duty vehicle space where the major challenges are: (i) greater emphasis on economic viability, (ii) reluctance to take on risk associated with new technologies, and (iii) numerous diverse applications that preclude a one-size-fits-all approach to hybrid-electric powertrain design. Past studies on HEV powertrain design have either ignored battery degradation, or failed to holistically capture its impact from a lifecycle cost perspective. The focus of this effort is the development of …

Fuel Type Estimation Using Fuel System Parameters, Shambhavi Balasubramanian

Open Access Theses

A number of factors are responsible for an increased interest in alternative fuels for transportation and other uses. Among the most widely available alternative fuels are biodiesel and vegetable oil, both of which can be used to power a diesel engine. Biodiesel has higher density, viscosity, surface tension, sound velocity, and bulk modulus of elasticity than regular diesel fuel. This affects the fuelling, injection timing, and fuel spray and consequently the emission characteristics.

Estimation of fuel type is critical to the performance of the engine. Knowing the fuel type allows the engine controller to determine the proper fuel quantity and …

Analysis Of Feedback Control Applied With Command Shaping To Minimize Residual Vibration, Nicholas L. Jacobs

Open Access Theses

Joint flexibility is a physical trait that affects all robotic systems to some degree. This characteristic has been shown to be very detrimental to the performance of these robotic systems when implementing fast point-to-point motion. During such motion, the robot will induce vibrations in its structure that will extend past the completion of the move. Many techniques have been applied over the years in order to minimize these residual vibrations. One such method is known as command shaping, which will construct the input profile so as to avoid exciting the natural frequencies of the system. This work seeks to extend …

Cyclic Tensile Response Of A Polyurethane Material, Yizhou Nie

Open Access Theses

Polyurethane is one of the most widely used polymer materials in the world. With the increasing demand of polyurethane, its mechanical behaviors are particularly of interest. In particular, the response of the material under a quasi-static loading being subject to an impact load. To delineate the effect of rate change on the mechanical response of polyurethane, a tensile experiment was designed where the specimen is initially subjected to quasi-static tensile loading and then to high-rate cyclic tension within the same experiment. Constant strain-rate experiments at both quasi-static and high strain rates are also conducted. The analysis of the results leads …

Advanced Hydraulic Systems For Next Generation Of Skid Steer Loaders, Mrudula Uday Orpe

Open Access Theses

Fluid power systems have been extensively used in off highway applications like skid steer loaders, wheel loaders, excavators since many years. Work has been done by both industry and academia to improve efficiency, reduce noise and leakages in these systems. With increasing competition in the market, importance is now also given to operator comfort and machine productivity in off highway applications.

Mobile, off – highway vehicles like Skid-steer loaders are widely used in labour saving applications like loading earth into a truck, dig and move material on construction sites to, clean roads, clear snow from roads etc. To carry out …

High-Throughput Mechanical Characterization Methods For Composite Electrodes And In-Situ Analysis Of Li-Ion Batteries, Luize Scalco De Vasconcelos

Open Access Theses

Electrodes in commercial rechargeable batteries are microscopically heterogeneous materials. The constituents often have large variation in their mechanical properties, making the characterization process a challenging task. In addition, the mechanical properties and mechanical behaviors of electrodes are closely coupled with the electrochemical processes of lithium insertion and extraction. There is an urgent need to develop an experimental platform to characterize the chemomechanical response of electrodes under the in-situ conditions of charge and discharge.

In the first part of this thesis, instrumented grid indentation is employed to determine the elastic modulus and hardness of the constituent phases of a composite cathode. …

Test Cell Set-Up To Enable Drive-Cycle Testing Of A Variable Valve Actuation Enabled Camless Diesel Engine, Alexander Harrison Taylor

Open Access Theses

The previous facility which was used for engine testing at Purdue's Ray W. Herrick Laboratories utilized an eddy current dynamometer which is only suited for steady-state testing and throttle snaps. To better utilize a pre-existing camless diesel engine, which is is enabled via variable valve actuation, it was desired to perform transient drive-cycle tests. To accomplish this goal, a variable frequency drive AC dynamometer was required. Given that a brand new facility was constructed, the team was presented with an opportunity for ground up design of a test cell.

The new test cell's operation was proved out using a cammed …

Experimental Characterization Of Scroll Expander For Small-Scale Power Generation In An Organic Rankine Cycle, Felipe Airoldi Accorsi

Open Access Theses

Organic Rankine Cycles (ORC) are thermodynamic power cycles designed to generate work from low temperature sources. The low temperature heat input, typically between 80 °C to 270 °C, allows them to recover energy from industrial waste heat, exhaust gas from diesel, engines, solar systems, geothermal systems, and others. This technology already is commercialized in large-to-medium-scale power plants; however, it is still in development for small-to-micro scale.

The operating principle of ORC comprises four major steps. First, the working fluid evaporates at high pressure using the heat transfer from the low temperature heat source. Then, the working fluid reduces its enthalpy …

Algorithms For Lidar Based Traffic Tracking: Development And Demonstration, Vamsi K. Bandaru

Open Access Theses

The current state of the art of traffic tracking is based on the use of video, and requires extensive manual intervention for it to work, including hours of painstaking human examination of videos frame by frame which also make the acquisition of data extremely expensive. Fundamentally, this is because we do not have observability of the actual scene from a camera which captures a 2D projection of the 3D world. Even if video were to be automated, it would involve such algorithms as RANSACK for outlier elimination while matching features across frames or across multiple cameras. This results in algorithms …

Modelling And Control Of A Parallel Through-The-Road Plug-In Hybrid Vehicle, Rohinish Gupta

Open Access Theses

With an increasing number of passenger vehicles, automotive emissions has become a major challenge. Among other pollutants, green house gas (GHG) emissions form a majority of the exhaust coming out of the tail-pipe and are blamed for the rising temperature of the earth. The net carbon emissions due to running a lightduty passenger vehicle are studied in the present thesis. Hybrid electric vehicles have been proven to have lower green house gas emissions than conventional vehicles as electricity is cleaner than fossil fuels.

Using a parallel-through-the-road hybrid architecture vehicle, different power management strategies are studied. To begin with, a detailed …

A Novel Mode-Switching Hydraulic Hybrid For An On-Highway Vehicle: A Study Of Architecture And Control, Hiral Jayantilal Haria

Open Access Theses

Increasing demand for fossil fuels, their limited reserves and the environmental effects resulting from the transportation sector has raised severe concerns to government agencies, transportation industry as well as the end-users. This has raised interests in improving the fuel economy of road vehicles. One of the promising technologies in this regard is hybridization of vehicle transmission. Hydraulic hybrids have progressively gained acceptance due to their high power density and low component costs relative to their electric counterpart.

Many different hydraulic hybrid architectures have been developed to achieve better power management and regenerative braking and have been tested for performance and …

The Effect Of Static And Dynamic Aging On Fatigue Behavior Of Sn3.0ag0.5cu Solder Alloy, Yiran Li

Open Access Theses

In microelectronic assemblies, solder joints serve as interconnection between different packaging levels and are an important cause for the failure of microelectronic products. Sn-Ag-Cu solder alloys became important after lead-based solder alloys were caused to be discarded by regulations in European Union and Japan. However, the constitutive behavior of Sn-Ag-Cu alloys is not as well understood as lead-based solder alloys, and many studies confirm the aging of these alloys with time. The aging of Sn-Ag-Cu alloys and its effect on mechanical behavior challenges the reliability prediction of microelectronic assemblies. In this study, the effect of pretest isothermal aging and in-test …

Parametric And Design Analysis On Thermoelectric Generators, Shouyuan Huang

Open Access Theses

In facing the limited energy source reserves and environmental problems, thermoelectric generators (TEGs) are one of the promising waste heat recovery systems. The modern TEGs for exhaust stream (e.g. from automobiles) can improve the fuel economy by around 5%, taking advantage of the recent developed thermoelectric (TE) materials.

In this work, we aimed at designing a TEG as an add-on module for a gas-phase heat exchanger with maximized power output, and without negative impact (e.g. maintaining a minimum heat dissipation rate from the hot side). We first developed a parametric optimization algorithm using response surface method (RSM) and genetic algorithm …

Investigation Of Digital Pump/Motor Control Strategies, Farid El Breidi

Open Access Dissertations

A pump is the heart of fluid power systems, it has a significant impact on the efficiency of many fluid power systems. Motors are the most common rotary actuators in fluid power systems. State-of-the-art pump/motor units can achieve efficiencies higher than 90% when operating at maximum displacement; however, as the displacement drops, the efficiency of these units drops to below 50%. A new digital pump/motor design aims at increasing these efficiencies by utilizing two electrically controlled high speed on/off valves per displacement chamber; these valves provide the ability to achieve variable displacement and allow freedom in choosing operating strategies. Such …

Modeling Transport Phenomena And Uncertainty Quantification In Solidification Processes, Kyle S. Fezi

Open Access Dissertations

Direct chill (DC) casting is the primary processing route for wrought aluminum alloys. This semicontinuous process consists of primary cooling as the metal is pulled through a water cooled mold followed by secondary cooling with a water jet spray and free falling water. To gain insight into this complex solidification process, a fully transient model of DC casting was developed to predict the transport phenomena of aluminum alloys for various conditions. This model is capable of solving mixture mass, momentum, energy, and species conservation equations during multicomponent solidification. Various DC casting process parameters were examined for their effect on transport …

Experimental, Theoretical And Computational Modeling Of Flow Boiling, Flow Condensation And Evaporating Falling Films, Chirag Rajan Kharangate

Open Access Dissertations

The transition from single-phase to two-phase thermal systems in future space vehicles demands a thorough understanding of phase change methods in reduced gravity, including microgravity. In this study, phase change methods like flow boiling, flow condensation and evaporative falling-films are investigated experimentally, theoretically and computationally.

The experimental part of the study consists of an investigation of the influence of inlet subcooling and two-phase inlet on flow boiling heat transfer and critical heat flux in a horizontal 2.5-mm wide by 5-mm high rectangular channel in different orientations with respect to Earth gravity using FC-72 as working fluid. High-speed video imaging is …