Mechanical Engineering Commons^™

Design And Manufacturing Of Functionally Graded Materials With Polymer Chain And Nano-Reinforcement Orientation For Compressive Applications, Sanjay Varma Kalidindi

Theses and Dissertations - UTB/UTPA

Functionally Graded Materials for compressive applications were designed and manufactured by tailoring the properties of Pure Polyethylene (PE) and Vapor Grown Carbon Nanofiber (VGCNF) Reinforced PE Composites. Properties of NRPC have been extensively studied. Properties are dependent on parameters such as the reinforcement/matrix interaction; reinforcement volume fraction, orientation, dispersion, and packing, and the final matrix microstructure. However, there is limited literature on their properties under compression loading. Compression strength studies for high density PE reinforced with VGCNF for different fiber volume fraction (0%, 5%, 10% and 15%) were carried out. The role of interface and alignment was studied. Samples were …

Electrorheology Of Fullerene Suspensions, Maricela Lizcano

Theses and Dissertations - UTB/UTPA

Electrorheological fluids are suspension materials whose rheological behavior changes with an applied voltage. In particular, the material changes from a fluid to a solid behavior with an applied voltage and reverses to its original state when the voltage is removed. This function classifies ER fluids as smart materials. ER fluids may be developed and used as mechanical devices with no mechanical parts such as pumps, actuators, and dampers. Until recently, research was concentrated with micro-particle suspension fluids. This research project investigates the electrorheology of carbon nano-particle suspension.

Comparison Of Sliding Mode And State-Feedback Control Applied To A Partially Treated Actively Constrained Layer Damped (Acld) Beam, Jose J. Rodriguez

Theses and Dissertations - UTB/UTPA

In this research, a sliding mode control (SMC) was utilized in the control of a partially treated, actively constrained layer damped (ACLD), Timoshenko beam model. The resulting vibration control was compared to the vibration control achieved by a state-feedback linear quadratic regulator (LQR) for several loading conditions. An observer was designed and model order reduction (MOR) was performed to achieve a simplified, efficient, and more controllable finite element system model. As a result of model simplification, modeling errors in the form of unstructured uncertainties were introduced into the system. It was determined that the SMC and LQR achieved similar vibration …

A Stochastic Production Cost Model For Remanufacturing Systems, Gaurang S. Patel

Theses and Dissertations - UTB/UTPA

Growing environmental concern throughout this decade coupled with enforced legislation, customer expectations and economic incentives have forced increasing number of manufacturers to take back their products from end user. Managing this reverse flow of products is called reverse logistics. The stochastic nature of returned products complicates the production planning for remanufacturing systems in reverse logistics. In this thesis a stochastic production cost model, considering various costs associated under different situations for remanufacturing systems of returned products is developed. A search algorithm method is recommended to determine optimal production run size, production rate and space for remanufacturing systems in reverse logistics. …

Composite Mechanical Property Enhancement Through The Use Of Y-End Shaped Short Fibers, Jin Tan

Theses and Dissertations - UTB/UTPA

This study uses Finite Element Analysis (FEA) to predict the mechanical property enhancement of the composites reinforced by end-shaped short fibers with different aspect ratios and volume fractions at microscale. Fibers used include conventional straight short fibers (CSSF), dumbbell-end shaped short fibers (DSSF), bone-end shaped short fibers (BSSF) and Y-end shaped short fibers (YSSF) with various lengths and angles. The critical distances between neighboring fiber ends for FEA modeling were theoretically deduced and numerically verified. This study has never been done before and the results fill a gap to this field.

In conclusion, planar-end Y-shaped short fiber reinforced composites showed …

Extension Of Stereolithography Mold Life Using Gas-Assisted Injection Molding, Dilip Bose Ramalingam Nagarajan

Theses and Dissertations - UTB/UTPA

Stereolithography (SL) molds show great promise for injection molding of limited number of parts, greatly reducing the time to product and production cost. However, they present challenges to designers because of their strength, thermal characteristics and shorter lifetimes compared to metal molds. Gas-assisted injection molding (GAIM) has been used to alleviate the problems of distortion and thermal damage. The use of GAIM makes it possible to produce a large number of parts compared to conventional injection molding in epoxy molds with higher quality. In this research solid models of the mold with different part geometry were created using CAD and …

The Use Of Confidence Intervals For The Control Limits Of X¯ And S Control Charts, Daniel A. Lopez

Theses and Dissertations - UTB/UTPA

This research focuses on the variation observed on the control limits of X¯ and S control charts, due to the sampling schemes. In previous studies it has been shown that the estimated control limits derived by a small number of subgroups does not help in setting up reliable control limits. It has also been shown that estimating control limits from a large number of subgroups is not a feasible option. In this research quantile tables will be derived by sampling from the standard normal distribution and used to explain the effects of sampling on the control limits. The tables will …

The Development Of Web-Based Aerobic And Anaerobic And Muscle Static Work Capacity Modules Using Legacy Cycle Approach, Anant Ravindra Deshpande

Theses and Dissertations - UTB/UTPA

The Legacy cycle is an instructional model that emphasizes inquiry. Learners are faced with progressively complex challenges. For each challenge, learners generate initial thoughts on how they might react to the challenges. In this thesis, a web based instructional method that evaluates interactivity and motivation is presented. The system presented in the thesis helps student to integrate the use of legacy cycle approach in the regular study of aerobic and anaerobic and muscle static work capacity modules. The thesis also focuses on developing modules which contain challenges encompassing various sections, which helps student as an asynchronous learning tool, intended for …

Dynamic Mechanical And Thermal Analysis Of Aligned Vapor Grown Carbon Nanofibers Reinforced Polyethylene, Jose Jaime Taha-Tijerina

Theses and Dissertations - UTB/UTPA

Dynamic-mechanical and thermal characterization of aligned vapor grown carbon-nanofibers (VGCNFs)-reinforced high-density polyethylene (HDPE) has been performed. VGCNFs with diameters ranging from 50–200nm were used. Nanofibers were purified to remove amorphous carbon and metal catalyst, resulting in deagglomeration, and creating an open network that allowed polymer infiltration during mixing. High-shear mixing was used to disperse and distribute the nanofibers uniformly within the matrix. Extensional flow at different draw ratios (λ) was used to obtain anisotropic nanoreinforced composite (NC) tapes. Dynamic Mechanical Analysis (DMA) showed a dual increase, in storage and loss modulus, with draw ratio. This behavior is attributed to the …

Adaptive Optimal Control Design For Stable Vibration Attenuation Of Active Constrained Layer Damping Beam Structure, Tatyana G. Korotkova-Egan

Theses and Dissertations - UTB/UTPA

Vibration suppression using active constrained layer damping (ACLD) has proven to be an invaluable means for improving the performance of a wide variety of engineering systems. The ACLD creates the hybrid of active and passive damping, attaining favorably high damping characteristics, while at the same time, combines unattractive attributes of both treatments, such as stability sensitivity. Control efforts are needed to achieve an adequate performance of the structures treated with ACLD. The purpose of this research is to investigate theoretically and numerically the adaptive optimal controller of the constrained layer damped beam system, using the classical three-layered distributed-parameter model that …

The Effects Of Nationality In The Intercultural Relationship In A Maquila Environment, Cultural Dimensions A Practical Approach, Daniel Martin Reynoso Ortiz

Theses and Dissertations - UTB/UTPA

The Maquiladora Industry has enhanced economic development in the U.S. and Mexico border region. Initially, investors came to set up assembly lines requiring a small amount of technical skill; however, increases in the technological level of products have created the need for companies to require more technical expertise from their staff. Today, the requirement is for the design or redesign of some of their products and the manufacturing processes required to make these products. This brings managerial problems in dealing with technical people in cross cultural environments. These problems deal with staffing issues such as getting the right people and …

Development Of New Heat Sink Technology For High-Density Microprocessors, Pedro Lopez Jr.

Theses and Dissertations - UTB/UTPA

This study investigates the performance of existing heat sinks and compares it with two heat-exchanger prototypes: aluminum-foam heat sink and PCM (phase-change material)-filled heat sink. Kapton flexible heaters are used to replicate the heat produced by a computer's CPU (central processing unit). A number of thermocouples are connected between the heater and the heat sink being used to measure the component's temperature. The thermocouples are also connected to a data acquisition card to collect the data using a LabVIEW program. The values obtained are compared to data published in literature to validate the experiments and the setup. This setup is …

Analysis Of Lifting Performance Capacity Through An Integrated Learning Curve Model, Jose Roel Flores

Theses and Dissertations - UTB/UTPA

Physical fitness specific to job demands is necessary for jobs that require moderate or heavy effort. Fitness training is needed not just when a new job is learned but also when an individual has been away from the job for a few weeks and returns to perform the task. The basic problem is to have a good understanding of the dynamics of performance capacities to establish training and retraining regimes to prevent overexertion. To obtain this, a better understanding of the behavior of performance capacity over time is necessary. A performance capacity training regimen was designed for tasks that required …

Analysis Of Performance Capacity Of Hand Grip Through An Integrated Learning Curve Model, Miguel Torres

Theses and Dissertations - UTB/UTPA

There are few activities or work task in the manufacturing industry that does not involve grip strength. That is why it is in the best interest of the manufacturing industry to have an understanding of the optimum grip strength gain capacity over time that would lead to better performance, accuracy and most of all prevent hand grip related injuries. For that reason, this thesis was concentrated in discovering a possible basic working model for estimating grip strength over time for a specific grip strength activity. The first step was to observe the trend characteristics of the strength gain data over …

Expert System Development For Hard Disk Drive Failure Analysis, Fernando Rodriguez Rosas

Theses and Dissertations - UTB/UTPA

The Computer's Hard Disk Drive is a complex high technology device, diagnosis of a failure is difficult even using sophisticated test equipments. These Drives are expensive and returning a new one when it fails within the warranty period is not an option. The failed drive must be tested and repaired. In the repair process the analysis and diagnosis of the failures is a key point in the process where decisions regarding the repair process that the failed Drive will follow. Therefore, there is a requirement to perform an effective analysis and provide an accurate diagnosis. The standard system utilized for …

Human Reliability Analysis In The Performance Of Advanced Cardiac Life Support Tasks, Lucia Veronica Rosas

Theses and Dissertations - UTB/UTPA

Error reduction in the performance of medical emergency situations is an area of great concern in today's society. This is specially the case when the situation involves a cardiac arrhythmia. These situations are generally categorized as Advanced Cardiac Life Support (ACLS) events. The American Heart Association provides the proper procedures that practitioners of ACLS should follow to provide care to patients presenting heart arrhythmia problems. These situations occur inside and outside the hospital, outside the hospital being the most critical ones considering the limitation of equipment and availability of qualified care. Errors made by the practitioners of ACLS in this …

Switching Decisions For Diversity Antennas Using Autoregressive Techniques, Sebastian Mani Puthenpurayil

Theses and Dissertations - UTB/UTPA

Decision-making on switching for diversity antennas has been given considerable attention in recent times in mobile radio communications. Due to multipath propagation of radio waves the signals undergo a phenomenon known as fading and there will be considerable reduction in the average signal strength. By having multiple antennas in the receiver or transmitter the signal strength can be improved by switching back and forth to the antenna that has the maximum signal strength. In this thesis we have used linear prediction method for making decisions on which antenna gives the maximum signal strength. Linear prediction is applied on a single …

The Rheological Behavior Of Carbon Nanofiber-Reinforced Thermoplastic Composites, Qiang Zeng

Theses and Dissertations - UTB/UTPA

A rheological study of the thermoplastic HDPE filled with vapor grow carbon nanofiber (VGCNF) has been performed with a RheoStress 150 Tester. VGCNF having average 50 nm diameter were used. These nanofibers were purified to provide for an open network of high purity nanofibers. A rheomixer was used to disperse the nanofibers uniformly in the polyethylene matrix because of shear working conditions. The influence of fiber loading, frequency and temperature on the rheology was investigated. Studies were carried out in the temperature range of 160 to 210°C and frequency range of 0.062 to 628.3 rad/s. The rheological measurements show that …

Using Commercial Finite Element Code Called Abaqus In Modeling Hybrid Constrained Layers Damping Beam Structure And Quantitative Determination Of The Stability Of Implant-Bone Interface Using Resonance Frequency Analysis, Daniel Delgado Jr.

Theses and Dissertations - UTB/UTPA

In Chapter 1, it has been demonstrated that the damping treatments for beam and plate structures are effective, and the vibrational behaviors of the systems considered are influenced by many geometrical and material parameters. This has led to an interest in developing advanced “intelligent” structures. In the past, passive and active damping mechanisms have been used to reduce vibration. The uses of passive constrained layers are limited, but it has dissipative qualities for all the modes of the structure; and the uses of active constrained layers are limited to a single mode control. Recent published papers, many have suggested that …

Automated Robotic Inspection System For Electronic Manufacturing, Roberto Alejandro Balderas

Theses and Dissertations - UTB/UTPA

An automated robotic inspection system for electronic manufacturing has been developed to identify pin defects of IC packages mounted on printed circuit boards using surface mount technology. The automated robotic inspection system consists of two robots, a computer, a CCD camera with frame gabber for image acquisition, and a customized windows program using neural network for on-line defect identification. Gray scale images of the pins on IC packages are acquired using ambient light. The images are filtered and formatted to appropriate size, so that Matlab neural network tool could be used. The images are used to train neural networks using …

A Neural Network-Based Vision System For Automated Separation Of Onion From Clod Using Mechanical Harvester, Demian Morquin

Theses and Dissertations - UTB/UTPA

A neural network classifier for separating clods from onions during harvesting has been developed. The separator consists of a multi-layer feedforward network that maps textural features computed from gray-scale images of onions and clods into the correct object. Texture features were computed from co-occurrence matrices that specify the spatial relationship of pixel values in an image. The textural features selected for this application consist of homogeneity, contrast, variance, and energy. The network was trained using the back-propagation algorithm. Based on the textural features classification, the effect of changing the network configuration on separation effectiveness was investigated. Factors including network topology …

Mathematical Modeling For Fabricating A Microstructure With A Pre-Specified Geometry Using Laser -Induced Chemical Vapor Deposition, Chaoyang Zhang

Doctoral Dissertations

Laser-induced chemical vapor deposition (LCVD) is an emerging new technique with many practical applications. To optimize the system for fabricating a microstructure with a pre-specified geometry in pyrolytic LCVD, a three-dimensional mathematical model is developed for predicting temperature distributions and laser dwell times across the substrate scanned by the laser beam. A microstructure is fabricated layer by layer, and for each layer the laser beam moves from one pixel to the next. The complicated correlations among temperature distribution, deposit growth rate, and laser dwell time are investigated. A purely heterogeneous reaction is assumed and any gas-phase transport is ignored.

A …

Fluid Flow In Micro-Channels: A Stochastic Approach, Hilda Marino Black

Doctoral Dissertations

In this study free molecular flow in a micro-channel was modeled using a stochastic approach, namely the Kolmogorov forward equation in three dimensions. Model equations were discretized using Central Difference and Backward Difference methods and solved using the Jacobi method. Parameters were used that reflect the characteristic geometry of experimental work performed at the Louisiana Tech University Institute for Micromanufacturing.

The solution to the model equations provided the probability density function of the distance traveled by a particle in the micro-channel. From this distribution we obtained the distribution of the residence time of a particle in the micro-channel. Knowledge of …

A Hybrid Finite Element-Finite Difference Method For Thermal Analysis In A Double-Layered Thin Film, Teng Zhu

Doctoral Dissertations

Thin film technology is of vital importance in microtechnology applications. For instance, thin films of metals, of dielectrics such as SiO2, or Si semiconductors are important components of microelectronic devices. The reduction of the device size to the microscale has the advantage of enhancing the switching speed of the device. The reduction, on the other hand, increases the rate of heat generation that leads to a high thermal load on the microdevice. Heat transfer at the microscale with an ultrafast pulsed-laser is also a very important process for thin films. Hence, studying the thermal behavior of thin films or of …

Kinetics Of Laser Chemical Vapor Deposition Of Carbon And Refractory Metals, Feng Gao

Doctoral Dissertations

Three-dimensional laser chemical vapor deposition (3D-LCVD) has been used to grow rods of carbon, tungsten, titanium, and hafnium from a variety of hydrocarbons and metal halide-based precursors. A novel computerized 3D-LCVD system was designed and successfully used in the experiments. A focused Nd:Yag laser beam (λ = 1.06 μm) was utilized to locally heat up a substrate to deposition temperature. The rods, which grew along the axis of the laser beam, had a typical diameter of 30–80 μm and a length of about 1 mm. The precursors for carbon deposition were the alkynes: propyne, butyne, pentyne, hexyne, and octyne. Propyne …

The Optimized Electrostatic Motor, Christopher Lee Rambin

Doctoral Dissertations

The most common means of electrically activated actuation is the electromagnetic motor. All electromagnetic motors have a low output to weight ratio and low energy efficiency. The motor's weight is due to the coils and magnets used to generate propulsion. The energy loss is mainly the result of Joule heating that is inherent with any current driven device. An electrostatic motor offers the potential of significantly less weight and higher energy efficiency. This lower weight characteristic is due to the epoxide material used to construct the major components of its propulsion unit. Greater efficiency results from the reduced Joule heating …

Two-Phase Flow In Microchannels, Roger Scott Stanley

Doctoral Dissertations

The purpose of this study was to investigate fluid mechanic and heat transfer characteristics of two-phase two-component flow in rectangular microchannels. Experiments were conducted using rectangular aluminum channels with hydraulic diameters ranging between 56 $\mu$m and 256 $\mu$m and aspect ratios which varied from 0.5 to 1.5. Both single- and two-phase tests were conducted using water and gaseous argon, helium, and nitrogen as the working fluids. The Reynolds number for both types of experiments ranged from approximately 50 to nearly 10,000. The Nusselt number ranged between 0.0002 and 70. The single- and two-phase experimental data were empirically correlated, using parameters …