Mechanical Engineering Commons^™

Developing A Self-Navigating Robot To Map Disaster Regions, Lily Compher

Summer Community of Scholars Posters (RCEU and HCR Combined Programs)

No abstract provided.

Ultrafast Laser Ablation Of Inconel 718 For Surface Improvement, Sampson Canacoo, Enrique Contreras Lopez, Oscar Coronel, Farid Ahmed, Jianzhi Li, Anil K. Srivastava

Manufacturing & Industrial Engineering Faculty Publications

Inconel 718 is considered difficult to machine because of its ability to maintain its properties at high temperatures. The low thermal conductivity of the alloy causes accelerated tool deterioration when machining. Selective laser melting (SLM) additive manufacturing introduces a possibility of eliminating these difficulties, and producing complex shapes with this difficult-to-machine material. However, high surface roughness and porosity usually occur at the surface of components produced through additive manufacturing. In this study, the surfaces of Inconel 718 samples produced through selective laser melting were treated using laser ablation. The process parameters for the laser ablation process were analyzed in …

Identifying Population Hollowing Out Regions And Their Dynamic Characteristics Across Central China, Bin Guo, Yi Bian, Lin Pei, Xiaowei Zhu, Dingming Zhang, Wencai Zhang, Xianan Guo, Qiuji Chen

Mechanical and Materials Engineering Faculty Publications and Presentations

Continuous urbanization and industrialization lead to plenty of rural residents migrating to cities for a living, which seriously accelerated the population hollowing issues. This generated series of social issues, including residential estate idle and numerous vigorous laborers migrating from undeveloped rural areas to wealthy cities and towns. Quantitatively determining the population hollowing characteristic is the priority task of realizing rural revitalization. However, the traditional field investigation methods have obvious deficiencies in describing socio-economic phenomena, especially population hollowing, due to weak efficiency and low accuracy. Here, this paper conceives a novel scheme for representing population hollowing levels and exploring the spatiotemporal …

In-Situ Measurements Of Temperature And Emissivity During Msw Combustion Using Spectral Analysis And Multispectral Imaging Processing, Shu Zheng, Weiguang Cai, Ran Sui, Zixue Luo, Qiang Lu

Mechanical and Aerospace Engineering Faculty Research & Creative Works

By using a novel multispectral imaging technology, the 2-D distributions of flame temperature and emissivity were measured in a 16 MW incinerator to co-fire municipal solid waste (MSW) and municipal sludge. A way to establish the relationship between the multispectral flame images and the temperature was proposed by combing the Newton iteration method and Hottel emissivity model. The results showed that the measured temperatures at different locations varied by 31.25% with a fixed steam evaporation rate, and 11.76% with different steam evaporation rates at a given port. The temperatures and emissivities decreased at upper locations due to the lower local …

Tuning The Thermodynamic, Optical, And Rheological Properties Of Thermoresponsive Polymer Solutions Via Silica Nanoparticle Shape And Concentration, Christopher A P Neal, Valeria León, Michelle C. Quan, Nondumiso O. Chibambo, Michelle A. Calabrese

Mechanical Engineering Faculty Publications

Hypothesis

The shape and quantity of hydrophilic silica nanoparticles (NPs) can be used to tune the microstructure, rheology, and stability of phase-separating polymer solutions. In thermoresponsive polymer systems, silica nanospheres are well-studied whereas anisotropic NPs have little literature precedent. Here, we hypothesize that NP shape and concentration lower the onset of rheological and turbidimetric separation of aqueous poly(N-isopropyl acrylamide) (PNIPAM) solutions.

Experiments

Differential scanning calorimetry (DSC), Fourier-transform infrared spectroscopy (FTIR), turbidimetry, and oscillatory rheology are utilized to examine interactions between NPs, PNIPAM, and water and to track changes in phase separation and mechanical properties due to NP concentration and shape. …

Effects Of Rotor-Airframe Interaction On The Aeromechanics And Wake Of A Quadcopter In Forward Flight, Denis-Gabriel Caprace, Andrew Ning, Philippe Chatelain, Grégoire Winckelmans

Faculty Publications

From small drones to large Urban Air Mobility vehicles, the market of vertical take-off and landing (VTOL) aircraft is currently booming. Modern VTOL designs feature a variety of configurations involving rotors, lifting surfaces and bluff bodies. The resulting aerodynamics are highly impacted by the interactions between those components and their wakes. This has consequences on the aircraft performance and on the downstream wake. Studying the effects of those interactions through CFD can inform the development of cheaper numerical models. In this work, we focus on the interaction between rotors and bluff bodies based on the example of a generic quadcopter …

Tactics Ideation Experiment Data, Thomas L. Ashworth, Carl D. Sorensen

ScholarsArchive Data

This data includes the template worksheets, as well as filled worksheets that include ideas written by the participants in a research experiment. This experiment tested the effectiveness of a novel tactics ideation method (i.e., Random Prompts method) to a modified Brainwriting method. Transcribed copies of this data are also included.

Accompanying the data are experiment briefing presentations, Python code for rapid evaluation of the data (the evaluation methods themselves were also developed by the authors), a spreadsheet file with evaluation data (this is a necessary input to the code), and organizational trees (for team idea sets) associated with the evaluation …

Modeling Of Two-Dimensional And Biological Materials Towards Diverse Nano-Systems Applications, Jatin Kashyap

Dissertations

This dissertation studies the demonstration of materials ranging from two-dimensional (2D) materials to small bio-molecules using various atomistic/molecular and sub-atomic particles (electron, hole, excitons) modeling techniques for multi-domain applications. Three categories of materials/systems are investigated as follows: 2D materials, biological materials, and complexes of 2D and biological materials.

The first problem demonstrates wrinkles' ubiquitous presence in two-dimensional materials significantly alters their properties. It is observed that water molecules, sourced from ambient humidity or transfer method, can get diffused in between Graphene and the substrate during the Graphene growth. The water diffusion causes/assists wrinkle formation in Graphene, which influences its properties. …

Optimizing Build Plate Adhesion Of Polymers In Fused Granule Fabrication Processes, Alex Schroeder, Jason Weaver

Faculty Publications

Perhaps the most crucial element of fused granule fabrication (FGF) is material adhesion; in order to achieve a successful product, the material being printed must adhere to the build plate. For optimal products, the material should only adhere to the build plate until the print is complete, then be easily removable. This paper examines the effects of different build plates, environments, and bonding agents on material adhesion during the FGF process in a CNC mill machine. The force to remove polycarbonate (PC) and polypropylene (PP) from build plates was tested with various bonding agents. Except in one case, the adhesive …

A Comparison Of Layer Deposition And Open Molding Of Petg By Fused Pellet Fabrication In An Additive Manufacturing System, Alex Gibson, Jason Weaver

Faculty Publications

Additive manufacturing continues to offer new possibilities in both production and economics. The industry has quickly adopted it to rapidly produce parts that would be difficult or cost preventative otherwise. Recent innovation has expanded its capabilities, however there are still significant limitations. Most AM processes are restricted by materials available, in producing large parts, or by not achieving material deposition speeds to make certain products feasible. In addition, tight tolerances for features and surfaces cannot be produced without substantial post processing. High-speed Fused Pellet Fabrication (FPF) in combination with Hybrid Manufacturing (HM) offers expanded capabilities as additive and subtractive process …

Trade-Off Characterization Between Social And Environmental Impacts Using Agent-Based Models And Life-Cycle Assessment, Joseph C. Leichty, Christopher S. Mabey, Christopher A. Mattson, John L. Salmon, Jason Weaver

Faculty Publications

Meeting the UN’s sustainable development goals requires designers and engineers to solve multi-objective optimization problems involving trade-offs between social, environmental, and economic impacts. This paper presents an approach for designers and engineers to quantify the social and environmental impacts of a product at a population-level and then perform a trade-off analysis between those impacts. In the approach, designers and engineers define the attributes of the product as well as the materials and processes used in the product’s life cycle. Agent-Based Modeling (ABM) tools that have been developed to model the social impacts of products are combined with Life- Cycle Assessment …

Evaluation Of Material Request Order To Support Sustainable Construction, Fajar Susilowati, Nur Nahdiah Anggraeni

Makara Journal of Technology

This study was conducted on one of Indonesia’s apartment projects, in which reinforced concrete is the main structure. Based on existing project data, this project experienced a decline in the construction work’s progress, thus reducing the project’s overall progress. This decline occurred because the delivery of concrete reinforcement material was delayed. This study aimed to determine the process of material request order and its relationship with the work implementation, as well as the factors that influenced the delayed arrival of concrete reinforcement material at the project site. The method used in this study was observation and interview. Data were analyzed …

Scaling Cellular Agriculture Production With Photolithography: A Study On Curing And Degradation, Alexis Garrett

Department of Mechanical and Materials Engineering: Dissertations, Theses, and Student Research

To meet the requirements for full production in cellular agriculture, a multi-disciplinary approach is required. New questions and understandings between different concepts, such as texture and cooking, need to be identified and how they correlate with cellular behavior and taste. This work focuses on understanding and developing photolithographic systems for scalable cellular agriculture. There were two specific research directions: 1) a traditional photolithography printing system was improved upon for mass manufacturing purposes and 2) mechanical analysis and degradation of key potential photolithographic biomaterials were tested for a food product. A novel digital rotational ultraviolet manufacturing (DRUM) process was developed, and …

Biofilms: Formation, Research Models, Potential Targets, And Methods For Prevention And Treatment, Yajuan Su, Jaime T. Yrastorza, Mitchell Matis, Jenna Cusick, Siwei Zhao, Guangshun Wang, Jingwei Xie

Department of Mechanical and Materials Engineering: Faculty Publications

Due to the continuous rise in biofilm-related infections, biofilms seriously threaten human health. The formation of biofilms makes conventional antibiotics ineffective and dampens immune clearance. Therefore, it is important to understand the mechanisms of biofilm formation and develop novel strategies to treat biofilms more effectively. This review article begins with an introduction to biofilm formation in various clinical scenarios and their corresponding therapy. Established biofilm models used in research are then summarized. The potential targets which may assist in the development of new strategies for combating biofilms are further discussed. The novel technologies developed recently for the prevention and treatment …

Numerical Investigation Of The Effect Of Inlet Turbulence Intensity On A Bluff-Body Stabilized Flame At Near Blow-Off Condition, Amir Ali Montakhab

Dissertations - ALL

This thesis investigates the effect of a boundary condition on the dynamics of a bluff-body stabilized f lame operating near blow-off condition. Special emphasis is given to the effect of inlet turbulence intensity. This work is motivated by the understanding that more stringent regulations on fossil fuels generated emissions necessitate the design of combustion systems that operate at very fuel-lean conditions. Combustion at very lean conditions, however, induces flame instability that can ultimately lead to flame fluttering and eventual extinction. The dynamics of the flame at lean conditions can therefore be very sensitive to its boundary conditions. To better understand …

Switched Kinematic And Force Control For Lower-Limb Motorized Exoskeletons And Functional Electrical Stimulation, Chen-Hao Chang

Dissertations - ALL

Millions of people experience movement deficits from neurological conditions (NCs) that impair their walking ability and leg function. Exercise-based rehabilitation procedures have shown the potential to facilitate neurological reorganization and functional recovery. Lower-limb powered exoskeletons and motorized ergometers have been combined with functional electrical stimulation (FES) to provide repetitive movement, partially reduce the burden of therapists, improve range of motion, and induce therapeutic benefits. FES evokes artificial muscles contractions and can improve muscle mass and strength, and bone density in people with NCs. Stationary cycling is recommended for individuals who cannot perform load-bearing activities or have increased risks of falling. …

Automatic Generation Of Near-Body Structured Grids, Yuyan Hao

Dissertations - ALL

Numerical grid generation has been a bottleneck in the computational fluid dynamics process for a long time when using the structured overset grids. Many current structured overset grid generation schemes like the hyperbolic grid generation method require significant user interaction to generate good computational grids robustly. Other grid generation schemes like the elliptic grid generation method take a significant amount of time for grid calculation, which is not desirable for computational fluid dynamics.

Herein a new grid generation method is presented that combines the hyperbolic grid generation scheme with the elliptic grid generation scheme that uses Poisson’s equation. The new …

Study Of Urethane Double-Coated Nylon Membranes For Fluid-Storage Applications, Micah Austin Howell

Masters Theses

Polymer-coated fabrics are used for many fuel and water storage applications, such as in U.S. military field operations. Urethane-double-coated nylon (UDCN) is one such material used in collapsible fluid storage tanks. Research into the mechanical properties of UDCN membranes under different environmental conditions is necessary for substantiating its current operations as well as developing new technologies. Novel modular, closed-loop and scalable pumped-storage hydropower (PSH) systems are one technology that could use UDCN membrane tanks in order to mitigate large costs, risks, environmental impacts, and time-for deployment associated with PSH system construction due to their modular, closed-loop technology. This study focuses …

Comprehensive Review Of Heat Transfer Correlations Of Supercritical Co2 In Straight Tubes Near The Critical Point: A Historical Perspective, Nicholas C. Lopes, Yang Chao, Vinusha Dasarla, Neil P. Sullivan, Mark Ricklick, Sandra Boetcher

Publications

An exhaustive review was undertaken to assemble all available correlations for supercritical CO2 in straight, round tubes of any orientation with special attention paid to how the wildly varying fluid properties near the critical point are handled. The assemblage of correlations, and subsequent discussion, is presented from a historical perspective, starting from pioneering work on the topic in the 1950s to the modern day. Despite the growing sophistication of sCO2 heat transfer correlations, modern correlations are still only generally applicable over a relatively small range of operating conditions, and there has not been a substantial increase in predictive capabilities. Recently, …

Navigating The Virtual Landscape: Implementing A Pedagogical Framework In A Virtual Summer Engineering Course To Enhance Students' Academic Development, Eleazar Marquez, Samuel Garcia

Mechanical Engineering Faculty Publications

In this evidence-based practice paper, the recently established CIRE educational model was incorporated, and modified, to establish an alternative pedagogical framework for a virtual, fast-paced summer engineering course in a private university in Texas. Transitioning to fully online courses in the wake of COVID-19 required a rapid modification of traditional pedagogical methods to overcome challenges such as the lack of academic resources and established campus practices, while simultaneously ensuring the academic and social development of students. In this regard, a pedagogical framework known as the CIRE model – which is the acronym for Communication, Initiation, Reduction, and Extension – was …

In-Person Instruction Or Remote Learning?: Understanding Students' Learning Experiences During Covid-19, Eleazar Marquez, Samuel Garcia

Mechanical Engineering Faculty Publications

Research attests that student success in engineering education is cultivated largely due to classroom environments, academic inclusion, and engagement in undergraduate research. It is further revealed that the social and academic fabric of the institution such as academic advising, peer tutoring, disability services, and outdoor recreational programs is essential towards fostering well-being, recruitment, retention, and student success. However, these studies were conducted in a period in which students experienced traditional face-to-face instruction. In the wake of COVID-19, most institutions responded by terminating in-person instruction, mandating to seek off-campus housing, and shifting to a fully remote context. As such, educators were …

Thermal Degradation And Organic Chlorine Removal From Mixed Plastic Wastes, Zhuo Xu, Victor Ierulli, Ezra Bar Ziv, Armando G. Mcdonald

Michigan Tech Publications, Part 1

Plastic waste accumulation has been growing due to the increase in plastic generation and the lack of infrastructure for recycling. One of the approaches is to treat the mixed plastic waste (MPW) through thermal processes to produce feedstocks for other applications. However, the presence of polyvinyl chloride (PVC) in MPW would produce HCl during processing and has negative impacts (emission, catalyst poisoning, etc.). In addition, due to the high heterogeneity of MPW, it is difficult to generate consistent experimental data. In this study, MPW was homogenized through double compounding–extrusion and then formed into a sheet to be treated at 400 …

Removal Of Selenium And Heavy Metals From Coal Combustion Residuals Wastewater Using Surface Modified Iron Based Media, Madan Tandukar, Alex Korff, Andrew Vincent, Chris Hardin

World of Coal Ash Proceedings

No abstract provided.

Collaborative Research: Harnessing Mechanics For The Design Of All-Solid-State Lithium Batteries, Haoran Wang

Funded Research Records

No abstract provided.

Myosin Ii Adjusts Motility Properties And Regulates Force Production Based On Motor Environment, Omayma Y. Al Azzam, Janie C. Watts, Justin E. Reynolds, Juliana E. Davis, Dana N. Reinemann

Faculty and Student Publications

Introduction—Myosin II has been investigated with optical trapping, but single motor-filament assay arrangements are not reflective of the complex cellular environment. To understand how myosin interactions propagate up in scale to accomplish system force generation, we devised a novel actomyosin ensemble optical trapping assay that reflects the hierarchy and compliancy of a physiological environment and is modular for interrogating force effectors.

Methods—Hierarchical actomyosin bundles were formed in vitro. Fluorescent template and cargo actin filaments (AF) were assembled in a flow cell and bundled by myosin. Beads were added in the presence of ATP to bind the cargo AF …

Disk Engine With Circumferential Swirl Radial Combustor, Brian Bohan, Marc Polanka, Bennett Staton

AFIT Patents

A disk engine and system configured to provide high power at a reduced axial length is disclosed herein. The disk engine includes a radial compressor, a compressor discharge manifold positioned circumferentially about compressor, a combustion chamber positioned within the discharge manifold and a radial turbine positioned radially inward of the combustion chamber.

Comparative Study Of Tapered Versus Conventional Cylindrical Balloon For Stent Implantation In Stenotic Tapered Artery, Xiang Shen, Jiabao Jiang, Hongfei Zhu, Kaikai Lu, Pengfei Dong, Linxia Gu

Department of Mechanical and Materials Engineering: Faculty Publications

The natural tapering of coronary arteries often creates a dilemma for optimal balloon sizing during stenting. The influence of different balloon types, namely, a tapered balloon and a conventional cylindrical balloon, on the mechanical performance of the stent as well as arterial mechanics was investigated via the finite element method. Stent free-expansion and stent deployment in a stenotic tapered artery were investigated numerically. The biomechanical behavior of the two balloon types was compared in terms of stent foreshortening, stent deformation, stent stress distribution, and arterial wall stress distribution. Results indicate that balloon types affect the transient behavior of the stent …

Three-Dimensional Printed Abdominal Imaging Windows For In Vivo Imaging Of Deep-Lying Tissues, Mitchell Kuss, Ayrianne J. Crawford, Olawale A. Alimi, Michael A. Hollingsworth, Bin Duan

Department of Mechanical and Materials Engineering: Faculty Publications

The ability to microscopically image diseased or damaged tissue throughout a longitudinal study in living mice would provide more insight into disease progression than having just a couple of time points to study. In vivo disease development and monitoring provides more insight than in vitro studies as well. In this study, we developed permanent 3D-printed, surgically implantable abdominal imaging windows (AIWs) to allow for longitudinal imaging of deep-lying tissues or organs in the abdominal cavity of living mice. They are designed to prevent organ movement while allowing the animal to behave normally throughout longitudinal studies. The AIW also acts as …

Purification Of Artepillin C (Arc) With Anticancer Activities From Supercritical Co2-Ethanol Extracts Of Brazilian Green Propolis By Using Adsorption Column Chromatography, Lin-Hsiang Chuang, Wen-Chin Chen, Wen Pei, Ming-Hsi Chuang, Todd Hsu, Po-Chao Chuang

Journal of Marine Science and Technology–Taiwan

Phenolic compounds with varying phenolic structures are present in both terrestrial and marine organisms. Artepillin C (ARC) is a prenylated phenolic compound produced specifically in Brazilian green propolis. Earlier studies have demonstrated the potential of ARC as a dietary supplement for cancer prevention due to its ability to suppress tumor growth and metastasis. Here we report the development of an effective adsorption chromatography combined with supercritical CO2 extraction for the massive purification of ARC. A mixture of supercritical CO2 and ethanol extract of Brazilian green propolis was passed through a stainless chromatographic column packed with protruding metals at 4,000 psi …

A Stochastic Sailing Speed Optimization And Vessel Deployment Problem In Liner Shipping, Dung-Ying Lin, Pak Weng Leong

Journal of Marine Science and Technology–Taiwan

In this research, we consider the stochastic sailing speed optimization and vessel deployment problem and examine the trade-off between sailing speed and the number of vessels required to provide a certain service in international liner shipping. Solving this kind of stochastic program is a challenging task. To address this issue, we construct a mathematical formulation based on Ng (1) and Ng (2) and enhance the linearization techniques from Wang and Meng (3) so that problem instances of an even larger scale can be solved. The proposed formulation has been numerically applied to solve realistic cases, and the empirical results show …