Mechanical Engineering Commons^™

Reliable Mode Tracking For Gradient-Based Optimization With Dynamic Stability Constraints, Taylor Mcdonnell, Andrew Ning

Faculty Publications

In order to construct mode-specific flutter constraints for use in gradient-based multidisciplinary design optimization frameworks, mode tracking must be used to associate the current iteration's modes with the modes corresponding to each constraint function. Existing mode tracking methods, however, do not provide a method by which to ensure the accuracy of mode associations, making them unsuitable for use in situations where obtaining correct mode associations is critical. To remedy this issue, a new mode tracking method is presented which incorporates backtracking logic in order to maintain an arbitrarily high degree of confidence in mode correlations during gradient-based optimization and/or during …

Nemesis Setup For Indirect Detection Of Wimps, W. H. Trzaska, Alexander Barzilov, T. Enqvist, K. Jedrzejczak, J. Joutsenvaara, M. Kasztelan, O. Kotavaara, P. Kuusiniemi, K. K. Loo, J. Orzechowski, J. Puputti, M. Slupecki, J. Szabelski, I. Usoskin, T. E. Ward

Mechanical Engineering Faculty Research

We summarize the evidence for DM-like anomalies in neutron multiplicity spectra collected underground with Pb targets by three independent experiments: NEMESIS (at 210 m.w.e.) NMDS (at 583 m.w.e.), and ZEPLIN-II (at 2850 m.w.e.). A new analysis shows small but persistent anomalies at high neutron multiplicities. Adjusted for differences in detection efficiencies, the positions of the anomalies are consistent between the three systems. Also, the intensities match when corrected for the acquisition time and estimated detection efficiency. While the three measurements are inconclusive when analyzed separately, together, they exclude a statistical fluke to better than one in a million. To prove …

Experimental Investigations Of Yarn Pull-Out Behavior In Kevlar®: Influence Of Applied Metallic Coatings And Effect Of Dynamic Loading, Julie Ann Roark

Theses and Dissertations

Flexible woven Kevlar® textile fabrics are widely used in protective armor applications. Yarn pull-out, comprised of yarn uncrimping (i.e., straightening) and yarn translation, is a major energy absorption mechanism during ballistic impact onto these fabrics, especially for impact velocities below the ballistic limit. Yarn pull-out is influenced by various parameters including inter-yarn friction, pull-out distance, pull-out velocity, transverse pre-tension, fiber diameter, fabric architecture, fabric waviness, fabric count and yarn modulus.

The first part of this thesis investigates yarn pull-out behavior of commercially available Kevlar® KM2+ individual yarns coated with metallic layers (copper, aluminum, aluminum nitride, silver) via a directed vapor …

High-Throughput Computation Of Interfacial Thermal Management Of Wide-Bandgap Semiconductors, Hao-Wen Chen

Theses and Dissertations

As semiconductor electronics, in particular high electron mobility transistors, get hot in operation, people are trying to incorporate different semiconductor materials to solve the problem of heat dissipation to maintain the device efficiency and performance. In this master thesis, two different packages, LAMMPS and almaBTE, that are focusing on micro-scale and atomic scale respectively, are used to simulate the heat transfer process across interfaces in two different scales. In the LAMMPS simulation, the research is exploring how the location of atoms and the thickness of interfacial layers will influence the interfacial thermal conductance. On the other hand, using the almaBTE …

Uncrewed Aircraft Systems For Autonomous Infrastructure Inspection, Michail Kalaitzakis

Theses and Dissertations

Uncrewed Aircraft Systems (UAS) are becoming increasingly popular for infrastructure inspections since they offer increased safety, decreased costs and consistent results, compared to traditional methods. However, there are still many open challenges before fully autonomous, reliable, and repeatable UAS inspections. While a UAS platform has increased mobility and can easily approach hard to reach areas, it has limited range and payload capacity and is susceptible to environmental disturbances. Therefore, current operations are limited to Visual Line of Sight (VLOS) manual inspections that usually result in just a qualitative (visual) assessment of the structure.

The objective of this work is to …

Fabrication Of Asymmetrical Hollow Fiber-Supported Thin Film Membranes, Stack Assembly, And Accelerated Long-Term Stability Test For Oxygen Production From Air, Myongjin Lee

Theses and Dissertations

Air separation is a widely used process for oxygen production. Several separation technologies have been developed for air separation, including cryogenic distillation, swing adsorption, redox process of metal oxides, and electrochemical process. Among these technologies, electrochemical permeation process stands out as a cost-effective and simple process for pure oxygen production from air. The electrochemical permeation process employs a gas-tight membrane to permeate and separate oxygen from air directly, where the membrane conducts both ions and electrons simultaneously. Different membrane designs have been studied to obtain the improved performance for oxygen permeation, typically planar and tubular designs. Among these membrane configurations, …

Shear Localization In The Metallic Nanolayered Composites, Shujing Dong

Theses and Dissertations

In this dissertation, the influences of layer thickness (h), interface orientation relationship (OR) and dislocation slip activities on shear band (SB) formation mechanisms was investigated by means of molecular dynamics (MD) simulations.

The effect of h and dislocation slip systems on the shear localization in Cu-FCC/Nb-BCC MNCs was studied. The strain softening observed in those samples was triggered by the SB formation. The microstructure evolutions and dislocation slips revealed that the unsymmetrical dislocation transmission across the interface induces the shear localization and promotes the SB formation. The quantitative analysis of the change in the separation distance of initially …

Use Of Dic Measurements With Finite Element Models For Direct Heterogeneous Material Property Determination And Wrinkle Formation During Automated Fiber Placement, Sreehari Rajan Kattil

Theses and Dissertations

In this work, application of DIC in combination with finite element modeling is demonstrated for efficient material characterization for complex heterogeneous materials and tow wrinkle formation during automated fiber placement.

The first part of the work describes the integration of DIC measurements with finite element models for direct property identification in heterogeneous material systems. The material property identification is based on solving partial differential equations (PDE) of equilibrium for unknown elastic material properties with known boundary conditions and full field strain data (Eg. DIC). The PDEs are solved numerically using Petrov-Galerkin finite element procedure. The classical Bubnov-Galerkin method is shown …

Mems 411: T-Shirt Strip Dispenser, Andrei Schwartz, Evan Dorsel, Amy Gong, Rosie Finglass

Mechanical Engineering Design Project Class

Develop a device to facilitate the t-shirt strip lay down process for Prof. Mary Ruppert-Stroescu

Mems 411: Group B Prosthetic Arm Design, Gage Fuller, Abby Jaeger, Oliver Reid, Max Gordon

Mechanical Engineering Design Project Class

Design a custom prosthetic arm for a customer who is missing her arm two inches past her elbow. Introduce mobility so that she can utilize the arm to perform more everyday tasks than she was able to before with her immobile arm.

Mems 411: The Rock Collecting Rover Design Project, Henry Collins, Sam Mattecheck, Connor Burke

Mechanical Engineering Design Project Class

The rock collecting over project challenged groups to construct a small,, remote controlled rover that is able to move and collect dice.

Mems 411: Air Capture Dynamic Seal, Erik Truitt, Thomas Rexing, Cole Kelez, Hernan Perez

Mechanical Engineering Design Project Class

For the DAC (direct air capture) machine, a CO₂ collecting machine, it needs a seal that allows rotation while still being airtight. Currently, a liquid seal is used but is having issues with contamination and evaporation.

Mems 411: Dynamic Seal, Devin Fredericks, Abdul Majeed Lalani, Matthew Schmidt, Edward Tinnemeyer

Mechanical Engineering Design Project Class

The purpose of this design project is to design a dynamic seal to be used on AirCapture’s carbon capture machine. The task is to create an air-tight seal between the top and bottom halves of AirCapture’s carbon capture machine. The seal needs to be capable of periodically rotating and must not leak while in operation.

Synthesizing And Printing Of Tin Oxide Nanoparticles Using A Single Ultrafast Laser System: A Feasibility Study, Enrique Contreras Lopez, Farid Ahmed, Jianzhi Li

Manufacturing & Industrial Engineering Faculty Publications

In laser-based manufacturing, processing setup customization is one of the popular approaches used to enhance diversity in material processing using a single laser. In this study, we propose setup design modification of an ultrafast laser system to demonstrate both Tin Oxide (SnO2) nanoparticle synthesis from bulk metal, and post printing of said nanoparticles using Laser Induced Forward Transfer (LIFT) method. Using the Pulse Laser Ablation in Liquid (PLA-L) method, nanoparticles were synthesized from a bulk tin metal cube submerged in distilled water. Such nanoparticles dispersed in water can form colloidal ink that can be used for different printed electronics applications. …

A Numerical Study On The Powder Flowability, Spreadability, Packing Fraction In Powder Bed Additive Manufacturing, Yeasir Mohammad Akib, Ehsan Marzbanrad, Farid Ahmed, Jianzhi Li

Manufacturing & Industrial Engineering Faculty Publications

The powder bed fusion (PBF) process is widely adopted in many manufacturing industries because of its capability to 3D print complex parts with micro-scale precision. In PBF process, a thermal energy source is used to selectively fuse powder particles layer by layer to build a part. The build quality in the PBF process primarily depends on the thermal energy deposition and properties of the powder bed. Powder flowability, powder spreading, and packing fraction are key factors that determine the properties of a powder bed. Therefore, the study of these process parameters is essential to better understand the PBF process. In …

Ultrafast Laser Direct Writing Of Conductive Patterns On Polyimide Substrate, Ishrat Jahan Biswas, Enrique Contreras Lopez, Farid Ahmed, Jianzhi Li

Manufacturing & Industrial Engineering Faculty Publications

Laser direct writing (LDW) is a fast and cost-effective method for printing conductive patterns in flexible polymer substrates. The electrical, chemical, and mechanical properties of polyimide (PI) make it an attractive material choice for laser writing of conductive circuits in such polymer. Electrically insulating PI has shown great potential for flexible printed electronics as LDW enables selective carbonization in the bulk of such material leading to the formation of conductive lines. However, existing studies in this area reveal a few key limitations of this approach including limited conductivity of written structures and fragility of carbonized PI. Therefore, more research is …

Investigation Of Adhesion, Deformation Mechanics, And Electrical Properties Of Ag/Sio2/Pdms Tri-Layers For Stretchable Electronic Applications, Rhandy Joe Paladines

Theses and Dissertations

The motivation behind this research is to improve the interfacial layer bonding of metallic thin films to PDMS substrates with the aid of a buffer layer. The physical vapor deposition (PVD) technique of sputtering was used to deposit bilayer thin films of silver (Ag) and silicon dioxide (SiO2) on PDMS. Two chamber pressures were used in this work, 5 and 20 mTorr, to investigate the role of this parameter in determining the interfacial adhesion and the role in determining the resistance sensitivity. Studies of the surface energy and increased bonding strength for metallization are carried out. Surface characterization using atomic …

Machine Learning-Based Peripheral Artery Disease Identification Using Laboratory-Based Gait Data, Ali Al-Ramini, Mahdi Hassan, Farahnaz Fallahtafti, Mohammad Ali Takallou, Hafizur Rahman, Basheer Qolomany, Iraklis I. Pipinos, Fadi M. Alsaleem, Sara A. Myers

Department of Mechanical and Materials Engineering: Faculty Publications

Peripheral artery disease (PAD) manifests from atherosclerosis, which limits blood flow to the legs and causes changes in muscle structure and function, and in gait performance. PAD is underdiagnosed, which delays treatment and worsens clinical outcomes. To overcome this challenge, the purpose of this study is to develop machine learning (ML) models that distinguish individuals with and without PAD. This is the first step to using ML to identify those with PAD risk early. We built ML models based on previously acquired overground walking biomechanics data from patients with PAD and healthy controls. Gait signatures were characterized using ankle, knee, …

Machine Learning-Based Peripheral Artery Disease Identification Using Laboratory-Based Gait Data, Ali Al-Ramini, Mahdi Hassan, Farahnaz Fallahtafti, Mohammad Ali Takallou, Basheer Qolomany, Iraklis I. Pipinos, Fadi Alsaleem, Sara A. Myers

Department of Mechanical and Materials Engineering: Faculty Publications

Peripheral artery disease (PAD) manifests from atherosclerosis, which limits blood flow to the legs and causes changes in muscle structure and function, and in gait performance. PAD is underdiagnosed, which delays treatment and worsens clinical outcomes. To overcome this challenge, the purpose of this study is to develop machine learning (ML) models that distinguish individuals with and without PAD. This is the first step to using ML to identify those with PAD risk early. We built ML models based on previously acquired overground walking biomechanics data from patients with PAD and healthy controls. Gait signatures were characterized using ankle, knee, …

Turbine Cooling System With Energy Separation, James L. Rutledge, Matthew Fuqua, Carol M. Bryant

AFIT Patents

A method and system for cooling an engine and/or vehicle using energy separation is disclosed herein. An energy separation device is operable for separating a compressed gaseous coolant stream into a first relatively cooler coolant flow stream and a second relatively hotter coolant flow stream. The relative cooler coolant flow stream is directed to a first region requiring increased cooling and the relative hotter coolant flow stream is directed to a second region requiring lower cooling than the first region in the engine or vehicle.

Impact Of Zirconia Slurry In Steel Powder On Melt Pool Characteristics In Laser Powder Bed Fusion, Taylor Davis, Tracy W. Nelson, Nathan B. Crane

Faculty Publications

Purpose – dding dopants to a powder bed could be a cost-effective method for spatially varying the material properties in laser powder bed fusion (LPBF) or for evaluating new materials and processing relationships. However, these additions may impact the selection of processing parameters. Furthermore, these impacts may be different when depositing nanoparticles into the powder bed than when the same composition is incorporated into the powder particles as by ball milling of powders or mixing similarly sized powders. This study aims to measure the changes in the single bead characteristics with laser power, laser scan speed, laser spot size and …

Design Of An Innovative Hybrid Sandwich Protective Device For Offshore Structures, Hozhabr Mozafari, Fabio Distefano, Gabriella Epasto, Linxia Gu, Emanoil Linul, Vincenzo Crupi

Department of Mechanical and Materials Engineering: Faculty Publications

Lightweight foam sandwich structures have excellent energy absorption capacity, combined with good mechanical properties and low density. The main goal of this study is to test the application of an innovative hybrid sandwich protective device in an offshore wind turbine (OWT). The results are useful for offshore structure applications. Different lightweight materials (aluminum foam, agglomerated cork, and polyurethane foam) were investigated using experimental tests and numerical simulations. Closed-cell aluminum foam showed the best performance in terms of the energy absorption capacity during an impact. As such, a Metallic Foam Shell (MFS) device was proposed for the fender of offshore wind …

Effect Of Lubricant Type On Deep Drawing Ratio And Drawing Force During Cylindrical Cup Deep Drawing, Walid M. Shewakh

Emirates Journal for Engineering Research

Cylindrical cup deep drawing technology is used in various manufacturing processes. For example, it is used in the automotive industry to manufacture auto parts. It is also used in the manufacture of household items. Lubricants are used in metal forming, especially deep drawing, to reduce friction between the tool and the workpiece. As a result, lubrication reduces forming energy and forming steps, increases the drawing ratio and tool life, while preventing galling, seizure and surface damages to the products. In this paper, the main purpose was to increase the deep drawing ratio and reduce the drawing force by angling the …

Accurate Predictions Of Thermoset Resin Glass Transition Temperatures From All-Atom Molecular Dynamics Simulation, Gregory Odegard, Sagar Patil, Prashik Gaikwad, Prathamesh Deshpande, Aaron Krieg, Sagar P. Shah, Aspen Reyes, Tarik Dickens, Julia A. King, Marianna Maiaru

Michigan Tech Publications, Part 1

To enable the design and development of the next generation of high-performance composite materials, there is a need to establish improved computational simulation protocols for accurate and efficient prediction of physical, mechanical, and thermal properties of thermoset resins. This is especially true for the prediction of glass transition temperature (Tg), as there are many discrepancies in the literature regarding simulation protocols and the use of cooling rate correction factors for predicting values using molecular dynamics (MD) simulation. The objectives of this study are to demonstrate accurate prediction the Tg with MD without the use of cooling rate correction factors and …

Pseudo-Stem Banana Fiber As A Potential Low-Cost Adsorbent To Remove Methylene Blue From Synthetic Wastewater, Md. Wasikur Rahman, Sumaya Tarannum Nipa, Sarmin Zaman Rima, Md. Mahmudul Hasan, Raghunath Saha, Md. Abdul Halim, Yousuf Ali, Anjan Deb

Mechanical Engineering Faculty Publications

In this work, pseudo-stem banana (Musa acuminata) (PBF) fiber was utilized as a potential low-cost natural adsorbent to uptake methylene blue (MB) dye from synthetic wastewater by batch adsorption process. Different adsorption factors like contact time, pH, initial concentration, and adsorbent dosage were explored and found that the separation process is strongly pH dependent. Additionally, the adsorption data were fitted with various adsorption isotherms like Langmuir, Freundlich, Temkin, and Dubinin–Radhushkevich models to detect the adsorption equilibrium phenomena. Reaction kinetics was inspected using pseudo-first-order and second-order kinetic models. Mass transfer and intra-particle diffusion analyses indicate the adsorption mechanism of the system …

A Cfd-Based Scaling Analysis On Liquid And Paint Droplets Moving Through A Weak Concurrent Airflow Stream, Masoud Arabghahestani, Nelson Akafuah, Tianxiang Li, Kozo Saito

Progress in Scale Modeling, an International Journal

We conducted volume of fluids (VOF) multiphase model numerical simulations to obtain the interaction among all the major governing forces identified in our previous paper. Our numerical experiments are intended to assess the droplet generation process and the jetting behavior by providing specific input conditions, offering CFD as a tool to study scaling correlations instead of physical experiments. Water droplets that can represent waterborne paints were generated by piezo-generated sinusoidal waveforms at the inlet of the nozzle. The governing forces included the external piezo-based wave-generation force, the inertial force of droplets, the inertial force of air, the viscose force of …

Effect Of Degradation Of Methylene Blue Dye (Mb) By Using Erbium Oxide (Er2o3) Nps, Hind Ahmed Jasim, Farah Farman Abbass, Sarah A. Hamood, Hind Mohammed Hassan, Mohammed Sellab Hamza

Al-Esraa University College Journal for Engineering Sciences

In an experiment investigating the photo catalytic degradation of methylene blue using varied concentrations of Er2O3 nanoparticles, different conditions were tested including with and without sunshine, as well as in the absence of a UV source. The presence of a UV source was also considered in the research. UV-Visible spectroscopy was utilized to characterize the catalysts. The degradation of methylene blue dye was monitored by spectrophotometry by tracking dye absorbance at regular time intervals and adjusting the dye concentration. The results indicated that the most effective degradation of methylene blue dye occurred during a 5-hour irradiation time and in the …

Architecture Between Development And Ability Programs, Allaa Ahmed Rasheed, Ibrahim Jawad Kadhim

Al-Esraa University College Journal for Engineering Sciences

The development of architecture and its pursuit of perfection can only be achieved through society to reach a specific result when meeting new desires that arise as a result of human development, expanding individual and societal needs, and deepening their relationships in multifaceted ways. The research focuses on development as it requires a clear cumulative vision of the integrative relationship between practice and participation in interpreting the act (effect) from the force (influence). It emphasizes that the power of capabilities is understood through learning and education in describing the capabilities of architecture. This involves adopting new ideas and intellectual premises …

The Designing Of Contemporary Teaching- Learning Spaces According To Interactive Flow Action Local School Spaces-A Case Study, Aseel Jasem Al-Ataby, Anwar Subhi Ramadan Al-Qaraghuli

Al-Esraa University College Journal for Engineering Sciences

The world today faces many challenges related to environmental issues, as well as other social and economic challenges, and in light of intellectual, cognitive, and technical transformations, which led to the emergence of many new phenomena and concepts that correspond to them, including the concept of flow. This concept has been associated with many aspects of life, including architecture, whose importance has emerged recently in light of the challenge of the spread of the Corona virus and its effects on architecture with its residential, educational, and other spaces. This research focuses on the flow in the architectural space in general, …

A New Compact Triple-Band Micro-Strip Monopole Antenna Based On Minkowski Fractal Geometry, Hayder S. Ahmed, Zahra' Salah Ahmed, Sarah A. Hamood, Mohammed Sellab Hamza, Taha A. Elwi

Al-Esraa University College Journal for Engineering Sciences

Wireless communication systems have made significant advancements in size reduction, with antenna terminals remaining a primary challenge for system compatibility. As a result, much of industrial research is focused on antenna miniaturization in wireless systems. In this work, a novel compact Triple-Band Fractal (TBF) antenna is proposed, utilizing three coupling fractal patches with varying iteration levels of Minkowski geometry to provide three resonant bands. The antenna design is implemented using an antenna substrate with a dielectric constant of 10.8 and a thickness of 1.27 mm within the CST Microwave Studio environment. The zero iteration patch resonator is responsible for the …