Mechanical Engineering Commons^™

Characterizing Meteorological Forecast Impact On Microgrid Optimization Performance And Design, Robert Jane, Gordon G. Parker, Gail Vaucher, Morris Berman

Michigan Tech Publications, Part 1

A microgrid consists of electrical generation sources, energy storage assets, loads, and the ability to function independently, or connect and share power with other electrical grids. Thefocus of this work is on the behavior of a microgrid, with both diesel generator and photovoltaic resources, whose heating or cooling loads are influenced by local meteorological conditions. Themicrogrid's fuel consumption and energy storage requirement were then examined as a function of the atmospheric conditions used by its energy management strategy (EMS). A fuel-optimal EMS, able to exploit meteorological forecasts, was developed and evaluated using a hybrid microgrid simulation. Weather forecast update periods …

Development And Experimental Investigation Of Modular Crates For Industrial Packaging Applications, Marshal Louie, Kumar B

Journal of Applied Packaging Research

For the increased product varieties, engineered plywood crate production technique could not facilitate box size optimization. This paper investigates the implementation of modularity function onto the plywood crate to resize the pack cube volume on customer requirement and to reduce space wastage inside the box. This is achieved by using a new joint technique called “Flat- Post Tongue Joint”. The full-sized experimental work is carried out comprising Flexural test analysis on Flat-Post Tongue joint, Tensile test analysis on tongue joint and Box Compression Test analysis on the two developed models of modular crates namely Modifiable Reinforced Plywood Crate (MRPC) and …

Tra-1-60-Positive/Cd45low Cells Found In The Peripheral Blood Of Prostate Cancer Patients With Metastatic Disease – A Proof-Of-Concept Study, Claudia Schäfer, Yawen Ju, Youngbin Tak, Cesar Vazquez, Sangyoon J. Han, Edwin Tan, Et Al.

Michigan Tech Publications, Part 1

Purpose

Over 90% of all cancer related deaths are due to metastasis. However, current diagnostic tools can't reliably discriminate between invasive and localized cancers.

Patients and methods

In this proof-of-concept study, we employed the embryonic stem cell marker TRA-1-60 (TRA+) to identify TRA + cells within the blood of prostate cancer patients and searched for TRA + cells in men with metastatic and localized cancers. We isolated whole peripheral blood mononuclear cells from 26 metastatic prostate cancer patients, from 13 patients with localized prostate cancer and from 17 healthy controls. Cells were stained for DAPI, CD45 and TRA + by …

Frequency-Selective Metasurface Integrated Uncooled Microbolometers, Mahmoud Almasri, Edward C. Kinzel

Mechanical and Aerospace Engineering Faculty Research & Creative Works

A metasurface integrated microbolometer having a sensing layer (e.g., SixGeyO1-x-y). The presence of the metasurface provides selectivity with respect to wavelength, polarization and angle-of-incidence. The presence of the metasurface into the microbolometer affects conversion of electromagnetic to thermal energy, thermal response, electrical integration of the microbolometer, and the tradeoff between resistivity and temperature coefficient of resistance, thereby allowing the ability to obtain a sensing with high temperature coefficient of resistance with lower resistivity values than that of films without the metasurface. The presence of the metasurface removes the need for a Fabry-Perot cavity.

The Desorption Kinetics Of Methane From Nonaqueous Fluids For Enhanced Well Control, James Lee Nielsen Jr.

LSU Master's Theses

The mass transfer of a dissolved gas evolving to return to the gaseous phase from a liquid is governed by many parameters. This process affects the development of an oil and gas well due to the possibility of gas contamination occurring from either an influx entering the wellbore, or drilling through gas-bearing formations. Once this dissolved hydrocarbon gas circulates up the wellbore, it will begin to evolve from solution and poses a potential risk to drilling equipment, the environment, and personnel at a drilling rig. Being able to predict the behavior of gas desorption based on a known set of …

Aluminum Parts Fabricated By Laser-Foil-Printing Additive Manufacturing: Processing, Microstructure, And Mechanical Properties, Chia Hung Hung, Yingqi Li, Austin Sutton, Wei Ting Chen, Xiangtao Gong, Heng Pan, Hai Lung Tsai, Ming-Chuan Leu

Mechanical and Aerospace Engineering Faculty Research & Creative Works

Fabrication of dense aluminum (Al-1100) parts (>99.3% of relative density) by our recently developed laser-foil-printing (LFP) additive manufacturing method was investigated as described in this paper. This was achieved by using a laser energy density of 7.0 MW/cm2 to stabilize the melt pool formation and create sufficient penetration depth with 300 μm thickness foil. The highest yield strength (YS) and ultimate tensile strength (UTS) in the LFP-fabricated samples reached 111 ± 8 MPa and 128 ± 3 MPa, respectively, along the laser scanning direction. These samples exhibited greater tensile strength but less ductility compared to annealed Al-1100 samples. Fractographic …

The Performance Of Sio2 And Tio2 Nanoparticles As Lubricant Additives In Sunflower Oil, Vicente Cortes, Karen Sanchez, Mataz Alcoutlabi, Javier A. Ortega

Mechanical Engineering Faculty Publications

In recent years, there has been growing concern regarding the use of petroleum-based lubricants. This concern has generated interest in readily biodegradable fluids such as vegetable oils. The present work evaluated the rheological and tribological characteristics of sunflower oil modified with silicon dioxide (SiO2) and titanium dioxide (TiO2) nanoparticles as lubricant additives at different concentrations. A parallel plate rheometer was used to evaluate the effects of concentration and shear rate on the shear viscosity, and the experimental data was compared with conventional models. The wear protection and friction characteristics of the oil-formulations were evaluated by conducting block-on-ring sliding tests. Surface …

Metal Additive Manufacturing Parts Inspection Using Convolutional Neural Network, Wenyuan Cui, Yunlu Zhang, Xinchang Zhang, Lan Li, Frank W. Liou

Mechanical and Aerospace Engineering Faculty Research & Creative Works

Metal additive manufacturing (AM) is gaining increasing attention from academia and industry due to its unique advantages compared to the traditional manufacturing process. Parts quality inspection is playing a crucial role in theAMindustry, which can be adopted for product improvement. However, the traditional inspection process has relied on manual recognition, which could suffer from low efficiency and potential bias. This study presented a convolutional neural network (CNN) approach toward robust AM quality inspection, such as good quality, crack, gas porosity, and lack of fusion. To obtain the appropriate model, experiments were performed on a series of architectures. Moreover, data augmentation …

Characterization Of Inertial Particles In The Turbulent Wake Of A Porous Disk, Kristin Nichole Travis

Dissertations and Theses

This study presents the findings of a wind tunnel experiment investigating the behaviour of micrometric inertial particles in the turbulent wake of a stationary porous disk. Various concentrations [Φ_v ∈ (2.95 x 10^-6 - 1.22 x 10^-5)] of polydisperse water droplets (diameter 13-41 µm) are compared to sub-inertial tracer particles. Hot-wire anemometry, phase Doppler interferometry and particle image velocimetry were implemented in the near and far wake regions to study the complex dynamics of the particles. Turbulence statistics and particle size distributions are presented and used to explore the particle wake interaction.

Clinical Evaluation Of Stretchable And Wearable Inkjet-Printed Strain Gauge Sensor For Respiratory Rate Monitoring At Different Body Postures, Ala’Aldeen Al-Halhouli, Loiy Al-Ghussain, Saleem El Bouri, Fuad Habash, Haipeng Liu, Dingchang Zheng

Mechanical Engineering Graduate Research

Respiratory rate (RR) is a vital sign with continuous, convenient, and accurate measurement which is difficult and still under investigation. The present study investigates and evaluates a stretchable and wearable inkjet-printed strain gauge sensor (IJP) to estimate the RR continuously by detecting the respiratory volume change in the chest area. As the volume change could cause different strain changes at different body postures, this study aims to investigate the accuracy of the IJP RR sensor at selected postures. The evaluation was performed twice on 15 healthy male subjects (mean ± SD of age: 24 ± 1.22 years). The RR was …

Multi-Mode Guided Wave Detection Of Various Composite Damage Types, Hanfei Mei, Robin James, Victor Giurgiutiu

Faculty Publications

This paper presents a new methodology for detecting various types of composite damage, such as delamination and impact damage, through the application of multimode guided waves. The basic idea is that various wave modes have different interactions with various types of composite damage. Using this method, selective excitations of pure-mode guided waves were achieved using adjustable angle beam transducers (ABTs). The tuning angles of various wave modes were calculated using Snell’s law applied to the theoretical dispersion curves of composite plates. Pitch–catch experiments were conducted on a 2-mm quasi-isotropic carbon fiber-reinforced polymer (CFRP) composite plate to validate the excitations of …

The Optimization Of Machining Parameters For Milling Operations By Using The Nelder Mead Simplex Method, Yubin Lee

Dissertations and Theses

Machining operations need to be optimized to maximize profit for computer numerical control (CNC) machines. Although minimum production time could mean high productivity, it can not guarantee maximum profit rate in CNC milling operations. The possible range of machining parameters is limited by several constraints, such as maximum machine power, surface finish requirements, and maximum cutting force for the stability of milling operations. Among CNC machining parameters, cutting speed and feed have the greatest effect on machining operations. Therefore, cutting speed and feed are considered as main process variables to maximize the profit rate of CNC milling operations.

A variety …

Spectroscopic Investigations On Pvdf-Fe2o3 Nanocomposites, Dorina M. Chipara, Victor Kuncser, Karen Lozano, Mataz Alcoutlabi, Elamin Ibrahim, Mircea Chipara

Mechanical Engineering Faculty Publications

Polyvinylidene fluoride-iron oxide (PVDF-Fe2O3) nanocomposites have been obtained my melt mixing of PVDF with Fe2O3 nanoparticles. The interactions between the polymeric matrix and the nanofiller have been investigated by wide angle X-ray scattering (WAXS), Fourier transform infrared spectroscopy (FTIR), and Raman spectroscopy, using both red and green excitations (lasers). WAXS, FTIR, and Raman spectra confirm that all samples contain α PVDF as the major crystalline form of the polymeric matrix. Experimental data revealed small changes in the positions of X-ray lines as well as modifications of the width of X-ray lines upon loading by Fe2O3 nanoparticles. FTIR and Raman spectra …

Near-Field Pressure Signature Splicing For Low-Fidelity Design Space Exploration Of Supersonic Aircraft, Christian R. Bolander, Douglas F. Hunsaker

Mechanical and Aerospace Engineering Student Publications and Presentations

As interest in supersonic overland flight intensifies, new ways to meet government restrictions on sonic boom loudness must be implemented. Low-fidelity aerodynamic tools, such as PANAIR, can estimate the near-field pressure signature that ultimately determines the loudness of the sonic boom at the ground. These tools can greatly benefit the exploration of large design spaces due to their computational efficiency. One of the limitations of low-fidelity tools is the accuracy of the solution produced, which is dependent on the fundamental physical assumptions made in the development of the governing equations. If flow patterns are produced that severely violate these fundamental …

Identifying Optimal Equivalent Area Changes To Reduce Sonic Boom Loudness, Troy Abraham, Douglas F. Hunsaker, Jonathan M. Weaver-Rosen, Richard J. Malak Jr.

Mechanical and Aerospace Engineering Student Publications and Presentations

This work explores the design space created from modeling the effect of localized geometric changes on a supersonic aircraft’s near-field pressure signature. These geometric changes are used to alter the aircraft’s near-field pressure signature in a way that reduces its sonic boom loudness at the ground. The aircraft used in this work is the NASA 25D concept and its near-field pressure signature is modeled using two separate methods. The first method uses the PANAIR panel code to obtain a near-field pressure signature for an axisymmetric representation of the 25D. This near-field signature is propagated to the ground using the NASA …

Minimum Induced Drag For Tapered Wings Including Structural Constraints, Jeffrey D. Taylor, Doug F. Hunsaker

Mechanical and Aerospace Engineering Student Publications and Presentations

For a wing in steady level flight, the lift distribution that minimizes induced drag depends on a tradeoff between wingspan and wing-structure weight. In 1933, Prandtl suggested that tapered wings have an advantage over rectangular wings due to this tradeoff. However, Prandtl’s solutions were obtained using assumptions that correspond to rectangular wings. Therefore, his claim was not analytically proven by his 1933 publication. Here, an approach similar to Prandtl’s is taken with more general approximations that apply to wings of arbitrary planform. This more general development is used to study Prandtl’s claim about tapered wings. Closed-form solutions for the optimum …

The Effect Of Cutting Edge Geometry, Nose Radius And Feed On Surface Integrity In Finish Turning Of Ti-6al4v, Ian S. Brown, Julius M. Schoop

Mechanical Engineering Faculty Publications

While the respective effects of nose radius, feed and cutting edge geometry on surface integrity have each been studied at depth, coupling between these effects is not yet sufficiently understood. Recent studies have clearly established that cutting edge micro-geometries may not only have positive effects on tool-life, but can also be used to tailor surface integrity characteristics, such as surface roughness and near-surface severe plastic deformation. To further a more fundamental understanding of the effects of cutting edge micro-geometries on surface integrity, experimental turning data was generated for a varied range of cutting tool geometries and feeds. Scanning laser interferometry …

Electrathon Vehicle: Steering, Lathan Halaapiapi

All Undergraduate Projects

The Electrathon Vehicle project is an ongoing project that dates back to 2012. The Electrathon Vehicle began as a frame and three wheels when given to the EV club. In past projects the vehicle has had frame and suspension work. The current design is only partially assembled and does not allow for any steering in the vehicle. A steering system needed to be developed in order for the vehicle to be controlled while a person is sitting in the seat. A steering system was designed that could withstand the force of maneuvering the vehicle in excess of 30 mph. This …

Discrete Concealed Device Table, Shyne Mckay

All Undergraduate Projects

How can people hide devices in their homes without being obvious with its location? People use safes to hide devices but intruders will know immediately that’s where things are held. It’s a common issue that people are having their safes stolen or broken into. To answer this question, a device was created to conceal devices in plain sight without being noticed. It’s common to have a coffee table in ones living room. Combining the problem with this knowledge, a discrete concealed device table was created. The table looks normal to the naked eye, meaning one cannot tell that the table …

J.C.A.T.I. Automated Pyrolysis Project, James Lopez

All Undergraduate Projects

Previous students working on the JCATI project have created an oven that will be used for the Pyrolysis process of carbon fiber composites. The oven requires someone to operate it manually, as in they must lift up the cover, place the amount of material desired, and stop the oven when it reaches the desired time. This process can and should be made automated. This was achieved by creating a device that can select the amount of material needed for a batch, automatically put it in the oven through the cover, and then bring the material out of the oven at …

Heat Exchanger, Chance Linarez

All Undergraduate Projects

A water jet cutting machine can cause excess heat and humidity within a closed building, while also making it more difficult for the user to pick material off the cutting table. Water temperatures can reach as high as 150 degrees Fahrenheit in the tank. A system that would reduce the temperature of the water in a water jet tank would be beneficial for the occupants in the room in providing a better more comfortable work environment. Data was collected while the machine was in use. The data includes; temperature of water leaving the nozzle, the rate of change of tank …

Four Point Flexure Beam Fixture, Nikolay Bobritskiy

All Undergraduate Projects

Structural design is one of many important aspects in mechanical engineering. Newly discovered composites are making their way into the engineering world. These materials have certain properties which need to be tested in several ways before they can be put to application. One of such tests include the four-point bend test. The fixtures that can be purchased currently can be expensive, typically ranging from $700-$1,000. The University has been struggling to afford commercial jig at this cost and would be helpful if one were available. The device consists of a 6061-aluminum base making it light, cheap, and faster to manufacture …

Fire Fighter Robot, Mohammed Alhajri

All Undergraduate Projects

Mohammed Alhajri

Fire Fighter Robot

Abstract

This report talks about the firefighter robot which can be used for fighting against the fire and which can be controlled from a safe distance. The most important objectives of designing such a device were to design and implement a test environment. Also, the main objective was to design and fabricate the frame of the robot. Furthermore, it was necessary to design and implement a drive system. Some of the constraints in this project were that the designed robotic machine was not able to climb up the stairs. Also, the material was not able …

Asts Frame, Dustin Braun

All Undergraduate Projects

The automotive industry has been an industry of many breakthroughs in technology and mechanical systems over the course of its history. But in one area, its innovation has slowed. That is in the area of the short throw shifter. All aftermarket short throw shifters are currently one dimensional. No adjustability, no ability to finetune to one’s personal desire. The goal of this project is to create a short throw shifter frame that is easier/faster to install, as well as allow for full adjustability of the shifter from inside the car. This frame design uses mostly 6061-T6 aluminum, along with some …

Ev Mirror Project, David Castillo

All Undergraduate Projects

An ongoing project for the Electric Vehicle Club is to build a fully working Electric Vehicle that can be used for any of the Electrathon America races across the country. Like most cars, the vehicle would need safety equipment that would allow the driver of the vehicle to drive the course both safely and efficiently. The event has specific requirements for the safety equipment that require the driver to be able to see behind them or when another driver is approaching from behind. Therefore, this project objective was to design and manufacture a set of mirrors that satisfy this requirement. …

Cubesat 5000, Renee Redman

All Undergraduate Projects

Cubesat 5000 is designed for the annual Physics weather balloon launch which is done for the senior level astrophysics students. Students use the weather balloons to get better visuals of the sun in the upper atmosphere. The purpose of the Cubesat 5000 design is to keep the instrumentation inside safe during and after the launch, maintain working temperature, and to remain below a 400-gram weight requirements in order to achieve optimum altitude.

The outer cube assembly was designed using Solidworks and printed using PETG filament. The weight of the cube has been measured and design changes were made done to …

Catmobile Ev Front Suspension, Daymon Fritz

All Undergraduate Projects

The Central Washington University (CWU) Mechanical Engineering Technology (MET) program owns an electric vehicle called the “Cat-Mobile” designed to be entered into an Electrothon America race. The Cat-Mobile is a collaborative project, various aspects of which are built by CWU MET students in the capstone sequence of the senior year. For the Cat-Mobile to operate safely and effectively, it was necessary to design and build a proper front suspension system. The suspension needed to meet Electrothon America Handbook rules dictating a minimum ground clearance of 2” and optimize material usage to keep added weight at or below 20lbs. Loading and …

Package Conveyance Stability Project, Sadie Mensing

All Undergraduate Projects

Dematic’s new model of conveyor is called the 9570 unit and is a highspeed live roller conveyor. This new model is designed to transport packages while maintaining a high speed of at least 3 m/s. While this new unit was being tested at the Dematic Tech center, it was discovered that when small and light weight packages get diverted onto the unit, they experience turbulence which causes the packages to spin or flip over. Orientation of packages on conveyor is extremely important for scanning purposes. In order to fix this problem, the problem first had to be replicated. A piece …

Speed Bump Power Generator, Sultan Alanazi, Osamah Abulgaith

All Undergraduate Projects

A large amount of energy is wasted by the vehicles on the speed breakers through friction. Energy can be produced by using the vehicle weight and speed. The team proposes a smart speed breaker that generates power (Speed bump power generator). The device allows vehicles to pass from both sides. The system makes use of mechanical assembly with metal sheets with linkages that press down with spring arrangement. Using the motion and weight of vehicles was the method that the team relied on to design the device. The mass of the vehicles allows the top plate to move the rack …

Automatic Bead Stringing Machine, Huy Dinh

All Undergraduate Projects

Humans were able to master the process of piercing objects through drilling holes as an advanced beading technique. There would be a great demand for beads and they appear more and more in human daily life. Many things are made from bead strings such as jewelry, furniture and house decoration. The beading process is usually done manually by hands of workers. The process takes a lot of effort and cost for labor. Therefore, this project is about building a simple device that helps to free the work effort and lower the labor cost. The bead strings machine has 3 main …