Open Access. Powered by Scholars. Published by Universities.®

Mechanical Engineering Commons™

Open Access. Powered by Scholars. Published by Universities.®

2020

Discipline
Institution
Keyword
Publication
Publication Type
File Type

Articles 631 - 660 of 1398

Full-Text Articles in Mechanical Engineering

Large Scale Grid Integration Of Wind And Solar Power With Storage, Nicholas Moore May 2020

Large Scale Grid Integration Of Wind And Solar Power With Storage, Nicholas Moore

Macalester Journal of Physics and Astronomy

The current energy grid in the United States is dominated by carbon intense energy generation methods that are based on production when and where it is required. However, solar and wind power have proved themselves as the most promising carbon free energy generation sources. Due to the unpredictable and uncontrollable nature of energy production from solar and wind, large scale integration of these resources into the electric grid will require robust storage capacity. In this project, we model the energy grid of the Midcontinent Independent System Operator (MISO) energy region with high concentrations of solar and wind power to analyze …

Go to article

Investigation Of Particle Interference In Induced Electromagnetic Coil, Elizabeth Soha May 2020

Investigation Of Particle Interference In Induced Electromagnetic Coil, Elizabeth Soha

Honors Scholar Theses

The purpose of this thesis work is to study the effect of a ferromagnetic particle on an induced solenoid’s magnetic field. Solenoids are wound coils that are charged with current to induce a magnetic field. The placement of a particle inside a solenoid interacts with the coil’s magnetic field and therefore changes the coil’s field behavior. This work comprises a parametric study of how particle size and placement within a solenoid affect the solenoid’s magnetic field. A model of the coil and particle is created and parametrically studied using the computational software ANSYS. The results from this simulation help to …

Go to article

New Policies Give Solar Users An Economic Boost, Olivia Fowler May 2020

New Policies Give Solar Users An Economic Boost, Olivia Fowler

Marriott Student Review

The future looks bright for Solar Energy, as more States and Territories in the United States commit to moving to 100% renewable energy. What are the different states and territories committing to exactly, and what economic incentives are they bringing? Find out in this article by author Olivia Fowley.

Go to article

A Perceptual Evaluation Of Short-Time Fourier Transform Window Duration And Divergence Cost Function On Audio Source Separation Using Non-Negative Matrix Factorization, Ryan J. Miller May 2020

A Perceptual Evaluation Of Short-Time Fourier Transform Window Duration And Divergence Cost Function On Audio Source Separation Using Non-Negative Matrix Factorization, Ryan J. Miller

Student Theses

Non-negative matrix factorization (NMF) is an established method of performing audio source separation. Previous studies used NMF with supplementary systems to improve performance, but little has been done to investigate perceptual effects of NMF parameters. The present study aimed to evaluate two NMF parameters for speech enhancement: the short-time Fourier transform (STFT) window duration and divergence cost function. Two experiments were conducted: the first investigated the effect of STFT window duration on target speech intelligibility in a sentence keyword identification task. The second experiment had participants rate residual noise levels present in target speech using three different cost functions: the …

Go to article

Dynamic Characterization Of Duroprotect, A Fiber-Reinforced Ballistics Composite, Ivy A. Turner May 2020

Dynamic Characterization Of Duroprotect, A Fiber-Reinforced Ballistics Composite, Ivy A. Turner

Honors Theses

Dynamic characterization of materials has become increasingly common, as it is important to understand how materials behave under sudden loads. Understanding these properties can aid in material selection for novel designs. DuroProtect, a fiber-reinforced ballistics composite developed by Rӧchling, was tested for its dynamic properties at high strain-rates. The Split Hopkinson Pressure Bar (SHPB) test was used to obtain dynamic properties at high strain-rates under compressive loading conditions. Tests were initially conducted to validate force equilibriums for each sample. The data measured from the strain gages mounted on the incident and transmission bars and the elastic wave propagation theories yields …

Go to article

Comparative Analysis And Dynamic Response Of Garolites Under Temperature Spectrum Using Low Velocity Impact Test, Birendra Chaudhary May 2020

Comparative Analysis And Dynamic Response Of Garolites Under Temperature Spectrum Using Low Velocity Impact Test, Birendra Chaudhary

Honors Theses

The purpose of this study was to examine the dynamic response of three different grades of garolites under the temperature spectrum. High-Temperature G-11 Sheet (HTG), Impact Resistance Garolite E-glass (HIG), and Economical Garolite (EG) were tested using an Instron Dynatup 8250 impact tester. Three specimens were used for all three composites and were tested at 6 different temperatures, -10oC, 25oC, 50oC, 100oC, 150oC and 200oC using the Low-Velocity Impact Machine with 20 Kip punch shear load cell. The results showed that HIG had the highest resistance to punch …

Go to article

Design Of An Orientation Device For Valve Bodies With Blowout Compatibility For Slug Detection, Annie Richardson May 2020

Design Of An Orientation Device For Valve Bodies With Blowout Compatibility For Slug Detection, Annie Richardson

Honors Theses

The Parker Hannifin plant in Batesville, MS, is a manufacturing plant that specializes in A/C and hydraulic tube and hose assemblies that support heavy machinery in the agriculture, logistics and construction industries. Customers place unique orders where the tube size, bending configurations, and adaptors vary widely. Some tubes require valve bodies where the customer can charge the A/C system once it has been assembled. A pierce and press machine is used to pierce the tube and place the valve body in the hole. Many tubes have asymmetric blocks at the end of the tube, with valve bodies placed at customer-requested …

Go to article

A Study Of The Marketing Analysis Concerning Mind The Gap: A Wall-Bed Space Saving Platform, Brenna Johnson May 2020

A Study Of The Marketing Analysis Concerning Mind The Gap: A Wall-Bed Space Saving Platform, Brenna Johnson

Honors Theses

The purpose of this thesis is to conduct a marketing analysis on the capstone project concerning the product titled Mind the Gap. The thesis will explore the potential industries that could be entered and marketing strategies that would be implemented if the Mind the Gap product was mass produced and either sold online or through brick and mortar locations. Outlined in this research is an analysis of the competitive landscape, potential target markets, situational aspects concerning this product, and the resulting recommended marketing mix. The Mind the Gap is centered around a practical and efficient process which has a goal …

Go to article

Product Realization Capstone: Using Project Management To Optimize Manufacturing Of Charcuterie Boards, Megan Staffieri May 2020

Product Realization Capstone: Using Project Management To Optimize Manufacturing Of Charcuterie Boards, Megan Staffieri

Honors Theses

The purpose of this project was to successfully create 36 charcuterie boards with varying designs during a two-week production period using principles of project management and manufacturing. In the initiation phase, the needs and requirements were assessed according to the project definition. During the planning phase, a work breakdown structure was created, material was researched, a budget was developed, and an initial risk assessment was performed. During the executing phase, the initial designs were prototyped before production began. The controlling phase was done in conjunction with the executing phase. The controlling phase monitored the project management plan and recorded the …

Go to article

Utilizing The Product Development Process To Bring An Idea From Concept To Production, Sydney Ferguson, Jackson Sneed May 2020

Utilizing The Product Development Process To Bring An Idea From Concept To Production, Sydney Ferguson, Jackson Sneed

Honors Theses

The purpose of this thesis is to document and discuss the five-stage product development process starting with defining a problem and resulting in manufacturing a final product for sale as it was implemented in the Portable Fire Pit Center for Manufacturing Excellence Senior Capstone Project. This project was carried out over the course of the Fall 2019 and Spring 2020 semesters by a team consisting of three Undergraduate Mechanical Engineering majors and two Undergraduate Accountancy majors. The ultimate goal of the project was to carry out a full production run of the Portable Fire Pit outputting fifteen units meeting retail …

Go to article

College Of Engineering Senior Design Competition Spring 2020, University Of Nevada, Las Vegas May 2020

College Of Engineering Senior Design Competition Spring 2020, University Of Nevada, Las Vegas

Fred and Harriet Cox Senior Design Competition Projects

Part of every UNLV engineering student’s academic experience, the senior design project stimulates engineering innovation and entrepreneurship. Each student in their senior year chooses, plans, designs, and prototypes a product in this required element of the curriculum. A capstone to the student’s educational career, the senior design project encourages the student to use everything learned in the engineering program to create a practical, real world solution to an engineering challenge. The senior design competition helps focus the senior students in increasing the quality and potential for commercial application for their design projects. Judges from local industry evaluate the projects on …

Go to article

Automating 35mm Photographic Film Digitization: X-Y Table Capture System Design And Assessment, Michael J. Bennett May 2020

Automating 35mm Photographic Film Digitization: X-Y Table Capture System Design And Assessment, Michael J. Bennett

Published Works

35mm still image formats are some of the most abundant photographic film types in cultural heritage collections. However, their special handling needs coupled with high resolution digital capture requirements have traditionally posed logistical constraints with regard to the formats’ digitization at scale. Through the use of a programmable X-Y table camera capture system, both slide and strip 35mm photographic film can be digitized in an automated fashion following Federal Agencies Digitization Guidelines (FADGI).

Go to article

A Study Of The Efficiency And Effectiveness Of The First Four Iterations Of Sierpinski Carpet Fractal-Like Fins At Increasing Angles In Natural Convection, Sophia N. Fleri May 2020

A Study Of The Efficiency And Effectiveness Of The First Four Iterations Of Sierpinski Carpet Fractal-Like Fins At Increasing Angles In Natural Convection, Sophia N. Fleri

Honors College Theses

Fractal geometries have been found in several studies to increase a fin’s thermal performance. Both the reductions of volume and mass accompanied by an increase in performance are desirable to prevent malfunction of the device through passive heat dissipation. The Sierpinski carpet fractal pattern, beginning with a basic square geometry in which an increasing number of perforations are incorporated through each successive iteration, reduces the fin’s mass while increasing its surface area simultaneously; this increase in surface area increases the rate of heat transfer experienced across the fin. The first four iterations of the Sierpinski carpet pattern, each with identical …

Go to article

The Development Of All Solid-State Optical Cryo-Cooler, Junwei Meng May 2020

The Development Of All Solid-State Optical Cryo-Cooler, Junwei Meng

Optical Science and Engineering ETDs

This dissertation describes the development of an all solid-state optical cryo-cooler. Crystals of 10% wt. ytterbium-doped yttrium lithium fluoride (Yb3+:YLF) are used to cool an infrared HgCdTe sensor payload to an absolute temperature below 135 K, equivalent to delta T equal 138 K below ambient. This record level of cooling is accomplished with a single stage, in a completely vibration-free environment, with a corresponding cooling power of 190 mW. This milestone is made possible by the design and fabrication of an undoped YLF thermal link that efficiently shields the payload with a non-right angle kink from intense anti-Stokes …

Go to article

Design Of A 3d Printed Bioreactor For Bone Cancer Research, Brooklyn K. Vanderwolde, Katelyn Hillson May 2020

Design Of A 3d Printed Bioreactor For Bone Cancer Research, Brooklyn K. Vanderwolde, Katelyn Hillson

The Journal of Undergraduate Research

Bone cancer is an aggressive disease and has peak occurrence during physiological stimulation of growth and aging. Astronauts who undergo long-term space missions also acquire an increased risk of bone tissue degeneration and cancer. Few in-vitro models currently exist capable of reproducing the complex microenvironment of bone tissue to support multicellular activity in a three-dimensional structure. This limits the ability to understand disease progression and develop suitable treatment strategies. Therefore, developing a bone tissue model and an associated bioreactor is critical to understand the risks associated with cancer progression and improve treatment and preventions related to those risks. The goal …

Go to article

Numerical Modeling Of Magnetic Fields For Mirror Neutron Search Experiment, Adam Johnston May 2020

Numerical Modeling Of Magnetic Fields For Mirror Neutron Search Experiment, Adam Johnston

Pursuit - The Journal of Undergraduate Research at The University of Tennessee

This paper will outline the configuration of 3D magnetic field model simulated from electric current sources using MATLAB. The model is using 3D arrays allowing for quick and accurate numerical approximations of Bio-Savart integrals, of error < , modeling the behavior of a magnetic field due to current carrying wires. We will discuss the development of a 3D magnetic field configuration produced by the current carrying wires around a large 2.5 m diameter vacuum beam tube in the proposed mirror neutron search experiment at High Flux Isotope Reactor (HFIR) at Oak Ridge National Laboratory (ORNL). The simulations demonstrate that the magnetic field with uniformity better than ± 2.5 mG that will allow for optimal results in experiment within the controlled range of net magnetic field magnitudes |B| 500 mG and in the large vacuum tube along 20-m neutron flight path can be achieved for an approximately 6 cm radius section at the center of the tube.

Go to article

Impact Resistant 3-D Printed Structures, Anna Schleper May 2020

Impact Resistant 3-D Printed Structures, Anna Schleper

The Journal of Undergraduate Research

This paper discusses the impact resistance of the mantis shrimp structure. Using past studies, an experiment was performed to identify an optimal wall thickness of a modified mantis shrimp structure. Various samples were 3-D printed using PLA and subjected to compression testing. Analysis of the data resulted in the finding that a wall thickness of 1.4 mm is the optimal thickness to obtain a lightweight, but impact resistant structure. These results are discussed further, along with any limitations of the findings.

Go to article

Spaspace Humidity Control Through A Single Speed Versus A Variable Speed Hvac Solution, Koukouni P. Kone May 2020

Spaspace Humidity Control Through A Single Speed Versus A Variable Speed Hvac Solution, Koukouni P. Kone

Mechanical Engineering Theses

Conventional air conditioning systems in houses respond to thermal loads by means of controlling dry-bulb temperature through the thermostat. As part of the process of conditioning the air, dehumidification is also provided. However, as houses are becoming more efficient, supplemental dehumidification is often necessary in homes located in hot and humid climates to control relative humidity intentionally. This study compared the dehumidification performance of three residential air conditioning systems: a system with a variable speed mode (VSPD), a system with an enhanced dehumidification mode activated (Enhanced Dehum), and a system without enhanced dehumidification capabilities (Normal Cooling). The research facility was …

Go to article

Concentrating Photovoltaic Retrofit For Existing Parabolic Trough Solar Collectors: Design, Experiments, And Levelized Cost Of Electricity, Todd P. Otanicar, Rhetta Wingert, Matthew Orosz, Clay Mcpheeters May 2020

Concentrating Photovoltaic Retrofit For Existing Parabolic Trough Solar Collectors: Design, Experiments, And Levelized Cost Of Electricity, Todd P. Otanicar, Rhetta Wingert, Matthew Orosz, Clay Mcpheeters

Mechanical and Biomedical Engineering Faculty Publications and Presentations

Photovoltaics and concentrating solar thermal power are two ways for generating electricity from sunlight, albeit through different methods. Parabolic trough style powerplants represent 3.6 GW of electricity production, but many of these plants are aging and being replaced with photovoltaics. An alternative option that could be employed to leverage the sunk capital cost associated with the primary optics would be the design of a pure photovoltaic retrofit working within the existing plant architecture. Here, a secondary optical concentrator is designed to use the existing primary optics of a parabolic trough type solar thermal powerplant. The design is a v-shaped secondary …

Go to article

A Generalisable Bottom-Up Methodology For Deriving A Residential Stock Model From Large Empirical Databases., Ciara Ahern, Brian Norton May 2020

A Generalisable Bottom-Up Methodology For Deriving A Residential Stock Model From Large Empirical Databases., Ciara Ahern, Brian Norton

Articles

Average reference dwellings representing a predominant housing typology are defined in this work. Specifying such reference buildings is a prerequisite for (i) calculating cost-optimal energy performance requirements for buildings and building elements and (ii) ensuring valid calculations of national building energy consumption. In the EU, an Energy Performance Certificate (EPC) rating is an assessment of the energy consumption of a dwelling. The use of inappropriate default-values for the building envelope thermal transmittance coefficients (U-values) and standardised thermal bridging transmittance coefficients (Y-values) in the production of EPCs leads to an over-estimation of potential energy savings from interventions in the existing dwelling …

Go to article

Heat Transfer Measurements And Enhancement For Materials And Processes In Polymer Extrusion Based Additive Manufacturing, Hardikkumar Mangaldas Prajapati May 2020

Heat Transfer Measurements And Enhancement For Materials And Processes In Polymer Extrusion Based Additive Manufacturing, Hardikkumar Mangaldas Prajapati

Mechanical and Aerospace Engineering Dissertations - Archive

Additive manufacturing (AM) is a burgeoning method for manufacturing over the subtractive manufacturing methodologies. Among the various method of polymer additive manufacturing the fused deposition modeling (FDM) also known as 3D printing is the most popular technique. In this technique, a rastering extruder dispenses a thermoplastic material on to a bed at a temperature greater than its glass transition temperature to build the part. Due to the additive nature of the process, AM introduces several challenges related to functional properties such as strength, thermal conductivity, etc of the eventual part. Measurement of thermal conductivity of additively manufactured polymer samples in …

Go to article

Reinitiation Mode Study Of Highly Irregular Detonation, Nandakumar Vijayakumar May 2020

Reinitiation Mode Study Of Highly Irregular Detonation, Nandakumar Vijayakumar

Mechanical and Aerospace Engineering Dissertations - Archive

The propagation of detonation waves is governed by their stability characteristics. Interest in highly unstable detonation grew when early experiments revealed limits of operation to be directly proportional to the stability of detonation. This research focuses on reinitiation pathways of highly irregular self-sustaining detonation. This is an important aspect of stability which is not yet fully understood, while many possible mechanisms have been proposed in the literature. First, a one-dimensional instability model simulation was performed using a global one-step chemistry mechanism to understand the different unstable modes by increasing the activation energy of a mixture of hydrogen and oxygen. The …

Go to article

Measurement And Optimization Of Thermal Transport Phenomena For Weld Strength Improvement In Polymer Extrusion Based Additive Manufacturing, Darshan Babu Ravoori May 2020

Measurement And Optimization Of Thermal Transport Phenomena For Weld Strength Improvement In Polymer Extrusion Based Additive Manufacturing, Darshan Babu Ravoori

Mechanical and Aerospace Engineering Dissertations - Archive

Additive manufacturing (AM) processes involve layer-by-layer addition of material to fabricate a 3-dimensional part. AM offers significant design and manufacturing flexibility compared to traditional manufacturing approaches. The major challenge in polymer-based additive manufacturing (AM) is that printed parts often have poor thermal/structural properties. These properties depend on weld strength of filaments and which intern depends on the degree of healing/neck growth between deposited polymers. The major contribution of this dissertation is understanding the importance of heat transfer during the printing process on the polymer neck growth and presented with techniques to improve the thermal and structural strength of finished part. …

Go to article

Design And Optimization Of Thermal Management Approaches In Data Center Applications, Rajesh Kasukurthy May 2020

Design And Optimization Of Thermal Management Approaches In Data Center Applications, Rajesh Kasukurthy

Mechanical and Aerospace Engineering Dissertations - Archive

In the present day to day life, Internet of Things (IOT) is everything, i.e., Internet and telecommunication is needed for almost every task of our life, which require data centers. These data centers provide various facilities such as, data processing, storage, transmission, maintenance, operations etc., To perform these tasks, a huge amount of power is consumed, which in turn generates large amount of heat. As these data centers are to be made operational throughout the year, cooling of data centers is of utmost importance. The continued increase in heat flux at the chip level due to new and robust technology …

Go to article

Computational Study Of Air-Cooled Servers With Improved Ducting And Chassis Re-Design, Himanshu Girishchandra Modi May 2020

Computational Study Of Air-Cooled Servers With Improved Ducting And Chassis Re-Design, Himanshu Girishchandra Modi

Mechanical and Aerospace Engineering Theses - Archive

In recent years there has been a phenomenal increase in cloud computing, net-working, virtualization, and storage which has led to an increase in demand for data centers. To meet this demand, there is a need for the latest computing nodes which causes an increase in power consumption. The cooling system occupy almost 40% portion of total energy consumption. Per ASHRAE TC 9.9, IT equipment needs to operate within recommended and allowable temperatures and humidity zone based on the circumstances. As the inlet air temperature increases, fan power consumption increases too and the Central Processing Units (CPUs) and high heat-generating components …

Go to article

Experimental Study Of Dynamic Cooling Of Racks Using Flow Control Devices, Fnu Akash May 2020

Experimental Study Of Dynamic Cooling Of Racks Using Flow Control Devices, Fnu Akash

Mechanical and Aerospace Engineering Theses - Archive

A data center is a cluster of multiple servers that a company uses to store and process large amounts of data. Due to never-ending demands, the processor densities are increasing every day. A higher processor density would result in the servers heating up more than it would normally creating a need for an efficient cooling system. On an average a water-cooled system would consume up to 40% of the total power required by a data center. Studies are being conducted on improving the overall efficiency of the system by either improving the thermal properties of the system or by improving …

Go to article

Modeling, Fabrication, And Characterization Of Porous Inconel 718 Structures Using Selective Laser Melting Process, Srihari Srivathsan May 2020

Modeling, Fabrication, And Characterization Of Porous Inconel 718 Structures Using Selective Laser Melting Process, Srihari Srivathsan

Mechanical and Aerospace Engineering Theses - Archive

Bio-inspired cellular structures are of great interest these days for many applications, from engineering research to industries. Honeycomb, Body-Centered Cubic with/without Z-struts (BCC-Z/ BCC), Face Centered Cubic with/without Z-struts (FCC-Z/ FCC), and Triply Periodic Minimal Surface (TPMS) such as Gyroid, Diamond, and Schwartz lattices are the most common bio-inspired lattice structures. These structures can be tailored based on their structural organization resulting in superior materials with lightweight properties, adequate strength, and low stiffness. Thankfully, additive manufacturing (AM) has made the fabrication of these complex cellular materials realistic. However, the use of AM could lead to several defects, such as damaged …

Go to article

Cfd Analysis On Liquid Cooled Cold Plate Using Copper Nanoparticles, Sarthak Agarwal May 2020

Cfd Analysis On Liquid Cooled Cold Plate Using Copper Nanoparticles, Sarthak Agarwal

Mechanical and Aerospace Engineering Theses - Archive

In today’s world, most data centres have multiple racks with numerous servers in each of them. The high amount of heat dissipation has become the largest server-level cooling problem for the data centres. The higher dissipation required, the higher is the total energy required to run the data centre. Although still the most widely used cooling methodology, air cooling has reached its cooling capabilities especially for High-Performance Computing data centres. Liquid-cooled servers have several advantages over their air-cooled counterparts, primarily of which are high thermal mass, lower maintenance and eventually lower costs by maintenance by labour. Nano-fluids have been used …

Go to article

Prediction And Validation Of Continuous Fiber Stiffened Plates Manufactured With Continuous Fiber Fabrication, Nabeel Ahmed Khan May 2020

Prediction And Validation Of Continuous Fiber Stiffened Plates Manufactured With Continuous Fiber Fabrication, Nabeel Ahmed Khan

Mechanical and Aerospace Engineering Theses - Archive

The purpose of this thesis was to develop an analytical method for predicting the structural properties of continuous fiber stiffened plates, which was then validated both experimentally and via finite element analysis. The MarkForged Mark Two 3D printer enables parts to be printed with continuous carbon fibers embedded within them. A manufacturing process was developed for printing stiffened grids with our without skins, with continuous fiber reinforcement on the top and bottom of the stiffening ribs, which allows bending stiffness can be maximized. An orthotropic grid was printed using Continues Filament Fabrication (CFF), an additive manufacturing process that embeds reinforcing …

Go to article

Experimental And Numerical Study Of Process Parameters Effects Towards Part Quality And Porosity During Powder Bed Additive Manufacturing Processes., Subin Shrestha May 2020

Experimental And Numerical Study Of Process Parameters Effects Towards Part Quality And Porosity During Powder Bed Additive Manufacturing Processes., Subin Shrestha

Electronic Theses and Dissertations

Powder bed additive manufacturing (PB-AM) process utilizes an electron beam or a laser as a heat source to melt the metallic powder particles. These processes have the capability of freeform fabrication, however certain defects such as porosity, high surface roughness, etc. would hinder its application. It is important to understand the effect of the process parameters and the underlying physical phenomena, which lead to the formation of such defects. In this regard, a three-dimensional (3D) thermo-fluid model is developed to study the effect of beam speed on the surface morphology during powder bed electron beam additive fabrication (PB-EBAF). Besides, the …

Go to article

First Prev Next Last