Mechanical Engineering Commons^™

Molecular Dynamic Simulations Of Mechanical Properties In Nb-Nbc Core-Shell Nanowires And Nodes, Austin Pauga

Graduate Research Theses & Dissertations

Nanoporous materials have attracted attention recently because of their extensive range of possible applications. These nanoporous materials are comprised of nanowires and nodes. A node joins three or more nanowires of different orientations. Current research has focused on nanowires and nodes composed of metallic single crystals and core-shells. Nanoporous materials experience brittle failure from the rupture of the weakest feature, overloading the other remaining structural features. To alter the deformation behavior of the network nodes, a ceramic layer has been added around the metal. Coating the metallic ligaments with ceramic shell increases the buckling capacity of each ligament and further …

In-Situ Optoelectronic Powder Flow Measurement Analysis For Directed Energy Deposition Applications, Mark Sliwka

Graduate Research Theses & Dissertations

Directed energy deposition (DED) is a metal additive manufacturing method of creating parts by using a high-power laser to fuse powdered metals into fully dense three-dimensional structures. To ensure the geometric and mechanical integrity of the completed part, the powder flow rate of the DED system must be accurate and repeatable for manufacturability. Due to its opacity and reflectivity, one method of measuring powder flow is by utilizing an optoelectronic sensor. The sensor consists of a diode laser with a line generator that emits a thin defocused light sheet, a photodiode, and a set of lenses. The corresponding lens collimates …

Thermal / Structural Analysis Of The Hb 650 Thermal Shield, Gerald J. Smith

Graduate Research Theses & Dissertations

Fermilab’s PIP-II project’s superconducting linear accelerator (Linac) will drive the next generation of particle accelerators through a revolution in beam intensity. Key to beam intensification are the high efficiencies of niobium-tin superconducting radiofrequency (SRF) cavities operating at cryogenic temperatures near 5 Kelvin. A multifaceted approach is employed to achieve and maintain the extreme temperature. Vacuum provides the first barrier to thermal convection. Physical thermal intercept zones further isolate the exterior shell vacuum vessel at 300 Kelvin from the supercooled beamline. The first thermal intercept lies just inside the exterior vacuum vessel forming the 40 Kelvin zone. This 40K thermal shield …

Numerical Investigation Of Darrieus Wind Turbine With Slotted Airfoil Blades, Ahmed Elbaz, Omar Sherif Mohamaed, Ahmed Abdelhamid Ibrahim, Ahmed Khaled Etman, Amr A. Abdelfattah

Mechanical Engineering

Low starting torque is considered as one of the major drawbacks of Darrieus type vertical axis wind turbine (VAWT). Design optimization to overcome this problem by modifying the airfoil geometry has received great attention by the wind energy community. Moreover, efforts have been directed towards augmenting the power coefficient of the turbine. In the present work, the effect of employing slotted airfoil as turbine blade on the performance and starting characteristics has been investigated. The slot parameters; slot location, angle of inclination, and dimensions, were optimized for NACA 0018 airfoil which is commonly used in Darrieus turbines. The flow over …

Binder Saturation, Layer Thickness, Drying Time And Their Effects On Dimensional Tolerance And Density Of Cobalt Chrome - Tricalcium Phosphate Biocomposite, John Ruprecht

All Graduate Theses, Dissertations, and Other Capstone Projects

Traditional metals such as stainless steel, titanium and cobalt chrome are used in biomedical applications (implants, scaffolds, etc.) but suffer from issues such as osseointegration and compatibility with existing bone. One way to improve traditional biomaterials is to incorporate ceramics with these metals so that their mechanical properties can be similar to cortical bones. Tricalcium phosphate is such a ceramic with properties such that it can be used in the human body. This research explores the use of the Binder Jetting based additive manufacturing process to create a novel biocomposite made of cobalt chrome and tricalcium phosphate. Experiments were conducted …

A Framework For A Successful Additive Repair System, Todd E. Sparks

Doctoral Dissertations

“The goal of this research is to generate a revolutionary improvement to the usability and usefulness of additive repair technology by integrating a set of tools into a seamless work flow. Insufficient automation in the current repair process is a huge hurdle in achieving cost-effective, reliable repairs. Many opportunities have been missed due to inconsistency, quality issues and lack of robustness and flexibility. The present work addresses deficiencies in preparatory steps such as 2D and 3D geometry processing, parameter estimation, and path planning as well as on-machine execution of the path plan. The bulk of the effort is focused on …

Human Behavior Understanding For Worker-Centered Intelligent Manufacturing, Wenjin Tao

Doctoral Dissertations

“In a worker-centered intelligent manufacturing system, sensing and understanding of the worker’s behavior are the primary tasks, which are essential for automatic performance evaluation & optimization, intelligent training & assistance, and human-robot collaboration. In this study, a worker-centered training & assistant system is proposed for intelligent manufacturing, which is featured with self-awareness and active-guidance. To understand the hand behavior, a method is proposed for complex hand gesture recognition using Convolutional Neural Networks (CNN) with multiview augmentation and inference fusion, from depth images captured by Microsoft Kinect. To sense and understand the worker in a more comprehensive way, a multi-modal approach …

Magnetic Control Of Transport Of Particles And Droplets In Low Reynolds Number Shear Flows, Jie Zhang

Doctoral Dissertations

“Magnetic particles and droplets have been used in a wide range applications including biomedicine, biological analysis and chemical reaction. The manipulation of magnetic microparticles or microdroplets in microscale fluid environments is one of the most critical processes in the systems and platforms based on microfluidic technology. The conventional methods are based on magnetic forces to manipulate magnetic particles or droplets in a viscous fluid.

In contrast to conventional magnetic separation method, several recent experimental and theoretical studies have demonstrated a different way to manipulate magnetic non-spherical particles by using a uniform magnetic field in the microchannel. However, the fundamental mechanism …

Combustion And Emission Characteristics Of Ic Engines Fueled By Hydrogen And Hydrogen/Diesel Mixtures And Multi-Objective Optimization Of Operating Parameters, Abdulhakim Issa Jabbr

Doctoral Dissertations

“The present study considers combustion of hydrogen in IC engines. In general, the work focuses on simulating the engine performance and emissions at different operation parameters, and using optimization techniques. Task I work deals with the engine performance and emissions of a single cylinder spark-ignition (SI) engine fueled by hydrogen. The engine was simulated at different equivalence ratios, exhaust gas recirculation (EGR) and ignition timing. The results indicate that NOx emissions, engine power, and efficiency are reduced by increasing EGR level, and increased with increasing equivalence ratio and advanced ignition timing. The best operating conditions for hydrogen engines were obtained …

Development Of Horizontal Axis Hydrokinetic Turbine Using Experimental And Numerical Approaches, Abdulaziz Abutunis

Doctoral Dissertations

“Hydrokinetic energy conversion systems (HECSs) are emerging as viable solutions for harnessing the kinetic energy in river streams and tidal currents due to their low operating head and flexible mobility. This study is focused on the experimental and numerical aspects of developing an axial HECS for applications with low head ranges and limited operational space. In Part I, blade element momentum (BEM) and neural network (NN) models were developed and coupled to overcome the BEM’s inherent convergence issues which hinder the blade design process. The NNs were also used as a multivariate interpolation tool to estimate the blade hydrodynamic characteristics …

Hydrokinetic Turbine Composite Blades And Sandwich Structures: Damage Evaluation And Numerical Simulation, Mokhtar Fal

Doctoral Dissertations

“Composite materials are gaining interest due to their high strength to weight ratio. This study deals with both experimental and numerical approaches to cover the aspects of the failure of composite materials in hydrokinetic turbine applications. In Part I, the location and magnitude of failure in the horizontal axis water turbine carbon fiber-reinforced polymer (CFRP) composite blades with different laminate stacking sequences were investigated. Two lay-up orientations were adopted for this work ([0⁰]₄ and [0⁰/90⁰]_2s). A finite element analysis model was generated to examine the stresses along the blade. Five angles were introduced to study the effect …

Additive Manufacturing Of Customized Lithium-Ion Batteries: Process Fundamentals And Applications, Xiaowei Yu

Doctoral Dissertations

“In the pasting decades, considerable efforts have been spent in developing the next-generation lithium-ion batteries (LIBs), from advanced active materials to new manufacturing methods. The development of additive manufacturing (AM) has brought new opportunities to LIBs. In this work, two AM methods are introduced for fabricating electrodes of LIBs. The first method is aerosol printing, which is a solvent-based wet additive method. Whereas the second method is a solvent-free, dry printing method. The commonly used materials for current collectors and active materials (including cathodes and anodes) of LIBs are aerosol printed and the electrochemical functionalities of the printed materials are …

Fabrication And Characterization Of Multifunctional Composites, Aditya R. Thakur

Doctoral Dissertations

“This study details the research to facilitate fabrication and characterization of novel structural composites reinforced with carbon fibers. Across industries, materials with high performance-to-weight ratio are sought after. Using carbon fibers as secondary phases in these proposed composites, specific characteristics can be tailored in these materials to manufacture strong, lightweight, high performance structures. The first part of the research focused on the improvement in the mechanical properties of the composites using carbon fiber reinforcement. As a part of this study, toughened ceramic composites with predictable failure patterns were produced using carbon fiber inclusions. A closed-form analytical model was developed to …

Finite Time Suboptimal Control Design Of Nonlinear Systems With Θ-D Technique And Implementation To Aerospace Applications, Jie Yao

Doctoral Dissertations

“A finite time suboptimal control strategy (named θ - D approximated algorithm) was proposed in this study, which can provide the control engineers with a novel effective and efficient design tool from the finite time optimal perspective. Based on the framework of this proposed method, the original nonlinear dynamics were formulated in pseudo-linear form, and the performance index was denoted by a linear quadratic regulator prototype in this research. After that, the approximated solutions to intractable Hamilton-Jacobi-Bellman (HJB) equation were acquired by putting vanishing perturbation terms into the performance index. By tuning the parameters in perturbation terms, semi-global stability and …

Measured And Modeled Performance Of A Spring Dominant Free Piston Engine Generator, Ramanjaneya Mehar Baba Bade

Graduate Theses, Dissertations, and Problem Reports (ETD)

Free Piston Engine Generators (FPEG) directly convert the reciprocating piston motion into electricity by using a linear alternator. Unlike conventional engines with piston motion restricted by a crankshaft mechanism, the FPEG piston motion is constrained by the energy available in the system. When stiff springs are considered in the design, the FPEG system attains high frequency with high power and efficiency. The main objective of this research was to model stiff spring-assisted FPEG system dynamics and performance accurately, and to apply the modeling results to the development of a 1kW, spark ignited, natural gas fueled, FPEG experimental prototype. The experimental …

Implementation Of Radial Basis Function Artificial Neural Network Into An Adaptive Equivalent Consumption Minimization Strategy For Optimized Control Of A Hybrid Electric Vehicle, Thomas P. Harris

Graduate Theses, Dissertations, and Problem Reports (ETD)

Continued increases in the emission of greenhouse gases by passenger vehicles has accelerated the production of hybrid electric vehicles. With this increase in production, there has been a parallel demand for continuously improving strategies of hybrid electric vehicle control. The goal of an ideal control strategy is to maximize fuel economy while minimizing emissions. The design and implementation of an optimized control strategy is a complex challenge. Methods exist by which the globally optimal control strategy may be found. However, these methods are not applicable in real-world driving applications since these methods require a priori knowledge of the upcoming drive …

Design And Development Of A Multi-Nodal Methane Detection System For Longwall Coal Mining, Amber P. Barr

Graduate Theses, Dissertations, and Problem Reports (ETD)

Methane (CH4) explosions pose significant dangers in longwall mining that may lead to injuries and fatalities. Safety is improved through diligent monitoring of CH4 concentration. Currently, regulations require a CH4 monitor be placed on the shearer, downwind of the cutting head. Portable monitor measurements must be taken at various times and locations. If any CH4 monitor measures a concentration greater than 1%, a warning signal must be given. Based on previous research and the location of the CH4 monitor mounted on the shearer (closest monitor to the face), if 1% methane is measured, the concentration at the face may be …

Observer-Based Event-Triggered And Set-Theoretic Neuro-Adaptive Controls For Constrained Uncertain Systems, Abdul Ghafoor

Doctoral Dissertations

"In this study, several new observer-based event-triggered and set-theoretic control schemes are presented to advance the state of the art in neuro-adaptive controls. In the first part, six new event-triggered neuro-adaptive control (ETNAC) schemes are presented for uncertain linear systems. These comprehensive designs offer flexibility to choose a design depending upon system performance requirements. Stability proofs for each scheme are presented and their performance is analyzed using benchmark examples. In the second part, the scope of the ETNAC is extended to uncertain nonlinear systems. It is applied to a case of precision formation flight of the microsatellites at the Sun-Earth/Moon …

Characterization And Recyclability Of 304l Stainless Steel Powder For Use In The Selective Laser Melting Process, Austin Taylor Sutton

Doctoral Dissertations

"Powder-bed fusion refers to a subset of additive manufacturing (AM) methods which successively melts and solidifies selected regions within a powder bed on a layer-by-layer basis to construct components directly from computer-aided design files. Laser Powder-Bed Fusion (L-PBF) is a process among the powder-bed fusion techniques that utilizes a laser to consolidate particles into a material with little porosity. During the L-PBF process, the large energy input from the laser causes the production of ejecta in the form of laser spatter and condensate, both of which have the potential to settle in the surrounding powder bed compromising its reusability. In …

Trajectory Control Of A Wheeled Robot Using Interaction Forces For Intuitive Overground Human-Robot Interaction, George Leno Holmes Jr.

Doctoral Dissertations

"Effective and intuitive physical human robot interaction (pHRI) requires an understanding of how humans communicate movement intentions with one another. It has been suggested that humans can guide another human by hand through complex tasks using force information only. However, no clear and applicable paradigm has been set forth to understand these relationships. While the human partner can readily understand and adhere to this expectation, it would be difficult for anyone to explain their intuitive motions with strict rules, algorithms, or steps. Uncovering such a procedural framework for the control of robotic systems to execute expected performance simply from force …

Dynamic Loading Experimentation And Surface Imaging Of Pressure Vessel Loadcell Fractures, Austin T. Sumner

Honors College Theses

Pressure vessels are very common pieces of equipment in industry and they are used for a variety of applications. It is standard in industry to rest pressure vessels on load cells. For some special cases, the pressure vessels are rested on load cells instead of solid foundation. Pressure vessels and their loadcells are generally designed for static environmental conditions and loading and tend to experience adverse effects when exposed to dynamic environments, such as hurricanes and earthquakes. These adverse-loading conditions cause vibrations and asymmetrical loading on the load cells, which can concurrently cause unexpected failure. This research investigates the effects …

A Numerical And Experimental Study On Effect Of Composition Of Ar-N2 Shielding Gas On The Weld Bead Profile And Its Prediction For Hot Wire Arc Additive Manufacturing, Niraj Pudasaini

College of Graduate Studies: Theses & Dissertations

Wire arc additive manufacturing is a process of making three-dimensional metal parts in a layer-by-layer approach using a feed wire and electric arc as a heat source. Wire arc additive manufacturing (WAAM) is becoming more popular due to its ability to create complex 3D parts, less build time, high deposition rate, and significant cost savings. Out of the many parameters used in WAAM, one of the important parameters is shielding gas which plays a significant role in material quality, properties, and defects. In this study, a controlled amount of Argon (Ar) and Nitrogen (N₂) shielding gases are used …

Performance Improvement Of Thermal-Driven Membrane-Based Solar Desalination Systems Using Nanofluid In The Feed Stream, Abdellah Shafieian, Muhammad Rizwan Azhar, Mehdi Khiadani, Tushar Kanti Sen

Research outputs 2014 to 2021

Different techniques have been proposed so far to improve the performance of thermal-driven membrane modules applied in solar desalination systems. These techniques have increased the freshwater productivity of the system but at the cost of its increased overall specific energy requirement. Due to this major drawback, the main objective of this study is to implement nanofluid in the feed stream of a heat pipe solar membrane-based desalination system, which not only aims to improve the freshwater productivity of the system, but also has the capability of decreasing its specific energy requirement. Synthetic seawater (with the salinity of 3.5%) was generated …

Integration Of Heat Pipe Solar Water Heating Systems With Different Residential Households: An Energy, Environmental, And Economic Evaluation, Abdellah Shafieian, Mehdi Khiadani

Research outputs 2014 to 2021

This study presents a detailed methodology for evaluating the energy, environmental, and economic contributions of heat pipe solar water heating (HPSWH) systems in various households. The hot water consumption patterns of Perth residents in Australia in one, two, and four-occupant houses are extracted in hourly basis throughout a year. The annual performance of the system is evaluated based on parameters such as saved energy, solar fraction, avoided CO₂ emission, saved money, and payback period. Moreover, an experimental rig is designed, manufactured, and tested. The results show that the contribution of the solar system in meeting the hot water demand …

Very High Cycle Fatigue Behavior Of Laser Beam-Powder Bed Fused Inconel 718 Considering The Layer Orientation And Surface Finish Effects, Palmer Frye

UNF Graduate Theses and Dissertations

Additive Manufacturing (AM) techniques have recently gained popularity for fabrication of parts used in aerospace applications. Some of these parts may be subjected to cyclic loading at very high frequencies, leading to service life requirements exceeding ten-million cycles (>10⁷ cycles). Therefore, understanding the very high-cycle fatigue (VHCF) behavior of these AM parts is an important step in their design and qualification processes. In this thesis, both high-cycle fatigue (HCF) and VHCF behaviors of Inconel 718, a Ni-base superalloy, manufactured via a Laser Beam-Powder Bed Fusion (LB-PBF) process, are investigated. Uniaxial, fully reversed force-controlled fatigue tests were conducted utilizing …

Efficacy Of Hard Hats In Attenuating Head Accelerations: A Combined Experimental And Computational Investigation, Arthur Aloisio Alves Dos Santos

UNF Graduate Theses and Dissertations

Struck-by accidents are a leading cause of traumatic brain injuries in the construction industry. While hard hats are the conventional means of industrial head protection, the current test standard to evaluate hard hat performance does not assess their ability to mitigate head accelerations from such impacts. To address this gap in knowledge, three investigations were pursued as part of this thesis. First, a variety of commercially available hard-hat designs – differentiated by shell design, number of suspension points, and suspension tightening system – were tested for their ability to attenuate accelerations during vertical impacts to the head. All hard-hats appreciably …

Effects On Initial Fixation Of Cementless Tibial Trays In Total Knee Arthroplasty, Brooke Fritts Thompson

Electronic Theses and Dissertations

Bone mineral density (BMD), among other factors, largely effect the initial stability of the cementless tibial tray component in a total knee replacement (TKR), where increased motion at the tray-bone interface hinders bony ingrowth. With a lack of bony ingrowth, the cementless implant will not experience long-term success. Understanding which factors influence initial stability yields insight into surgical technique considerations and help inform a surgeon’s implant choice. The objective of this study was to evaluate factors influencing the initial stability of cementless tibial trays using a 6-degree of freedom (6-DOF) robotic joint simulator, the AMTI VIVO, and combined loading scenarios …

Ultrasonic-Based Condition Assessment Of Wooden Utility Poles, Yishi Lee

Electronic Theses and Dissertations

More than 300 million utility poles shoulder the utility grid in the United States. However, the ineffectiveness of the current inspection process causes roughly a third of utility poles removed from the service deemed suitable for reuse. Due to the utterly essential role of the power infrastructure, budget shrinkage, and the structural degradation of the modern distribution grid, this Ph.D. dissertation addresses the challenges by proposing a physics-based signal analysis method with a jointly developed ultrasonic UB1000 system c to enhance the objectivity in ultrasonic-based nondestructive evaluation (NDE). The proposed methodology has been deployed commercially in the field and featured …

Cognitive Performance In Midlife Type 2 Diabetes: Results Form The Enbind Study, A. H. Dyer, L. Mckenna, G. Gamage, N. M. Bourke, Isabelle Killane, M. Widdowson, C. P. Woods, J. Gibney, R. Reilly, D. O'Neill, S. P. Kennelly

Articles

Aims: To establish the impact of uncomplicated type 2 diabetes on cognitive and neuropsychological performance in midlife. Methods: We performed a cross-sectional study of middle-aged adults with uncomplicated type 2 diabetes and a cohort of healthy control participants. General cognition was assessed using the Montreal Cognitive Assessment test and neuropsychological assessment was undertaken using a detailed neuropsychological assessment battery. Results: A total of 152 participants (102 with type 2 diabetes and 50 controls) were recruited (mean age 52 ± 8 years, 51% women). Participants with midlife type 2 diabetes were more than twice as likely to make an error on …

Wind Release Mechanical Sun Tracker, Tyler Andrus, Brady Fisher, Jt Gibson, Cynthia Rigby, Derek Smith

Mechanical and Aerospace Engineering

• Solar panel sun tracking system that releases solar panels to orient to wind flow in high wind conditions

• Operates on a single rotational motor

• Designed to be lightweight and portable