Mechanical Engineering Commons^™

Direct Solar Absorption Nanoparticle Doped Membranes For A Hybrid Membrane Distillation And Photovoltaic Cell, Alejandro Espejo Sanchez

Boise State University Theses and Dissertations

The growing demand for clean water supplies is driving the need for an innovative approach of water desalination. Developing a method for treating water with high salinities is possible with membrane distillation (MD). Additionally, MD is very attractive for pairing with solar energy due to the low temperature requirements. The integration of a membrane distillation system with a photovoltaic (PV) system will result in the co-production of electricity and clean water, thereby improving the economics of MD. Such a hybrid system will directly absorb thermal energy in the membrane for desalination while taking advantage of the spectrally selective nature of …

In Vitro Method To Quantify And Visualize Volumetric Wear In Meniscus Subjected To Joint Loading Using A 3d Optical Scanner, Kate J. Benfield

Boise State University Theses and Dissertations

The menisci are fibrocartilaginous soft tissues that act to absorb and distribute load across the surface of the knee joint. As a result of mechanical wear and large repetitive loading, meniscus tissue can begin to breakdown, or degenerate. Meniscus degeneration increases the risk of tearing, weakened tissue integrity, and the progression of osteoarthritis. Therefore, it is imperative to understand the wear behavior of whole human meniscus to identify conditions that may significantly increase the risk of degeneration.

The objective of this study is to develop and validate an in vitro methodology for characterizing volumetric wear behavior in whole human meniscus …

Validation Of Novel Obstructive Sleep Apnea Treatment With Silicone Gel Experimental Models, Dustin Walter Burd

UNLV Theses, Dissertations, Professional Papers, and Capstones

Predictive modeling to increase treatment success rates for surgical procedures is becoming more common in the scientific community. For obstructive sleep apnea (OSA), modeling has been predominately performed using computers as opposed to experimental models. Computer simulation saves time by eliminating the need to fabricate complex experimental models but comes at the expense of insight gained through physical observations made in real time. Experimental models for studying OSA are needed to validate computational work, provide perspective on anatomical scale and demonstrate complex deformations in real time. This work addresses prior hurdles in experimental model fabrication with a novel process using …

Minimizing Visual Defects Through Augmentation Of Computer Aided Diamond Rough Planning, Abhijith Prabhu

UNLV Theses, Dissertations, Professional Papers, and Capstones

Many computer aided design systems today utilize a workflow where physically accurate rendering of the product is not a functional component of its design process. This gap in workflow can lead to a sub optimal product or even a longer iterative design process in instances where a product's visual attributes and aesthetics are one their primary functional characteristic.

Diamonds are graded on their carat, color, clarity and cut, referred to as the 4Cs of a diamond; a standard set by G.I.A. and universally agreed upon. The cut of a diamond significantly affects the rest of the characteristics as it modifies …

Deepsea Coral Sample Container, Sara Passantino, Andrew Noble, Casey Smith, Thomas Smith

Mechanical Engineering

In order to better understand the health of our oceans and the species that inhabit them, scientists often collect samples for later analysis onshore. The demanding deep-sea environment makes this collection process a challenging engineering task. Samples must first be located, then removed from the seafloor and stored for transportation to the surface. The performance of the engineered solutions that complete each of these tasks is critical in allowing marine scientists to maximize the insight obtained from their expeditions. Marine Applied Research and Exploration (MARE) is an organization that performs such collection of organisms with the help of remotely operated …

Mono And Multi-Objective Optimization And Modeling Of Machining Performance In Face Milling Of Ti6al4v Alloy, Al Mazedur Rahman

Theses and Dissertations

Titanium alloys are extensively used in numerous industries like aerospace, automotive, military, etc., due to their exclusive characteristics. But machining these alloys has always been challenging for manufacturers. This research investigates the effect of radial depth of cut on cutting forces, tool life, surface roughness (Ra), and material removal rate (MRR) during face milling of Ti6Al4V alloy. It also aims to perform mono and multi-objective optimization of response characteristics to determine the optimal input parameters, namely cutting speed, feed rate, and radial depth of cut. Taguchi method and analysis of variance (ANOVA) have been used for mono-objective optimization, whereas Taguchi-based …

The Implementation And Comparison Of Fuzzy Logic Control Systems To Modern Control Methods On Low-Cost Hardware, Cristian A. Barron

Theses and Dissertations

Modern control engineering provides many options to automate systems for which a mathematical model is required. Another control does not rely on the mathematical model of the system and is known as fuzzy logic control. In this study, a literature review is conducted on existing control systems strategies such as proportional integral and derivative (PID), linear quadratic regulator (LQR), and fuzzy logic controller (FLC), the complexity of the systems they control, and their strengths and weaknesses. In addition, a series of experiments are conducted, both through simulations in MATLAB Simulink and using their implementation using the actual physical hardware to …

Optimizing A Railroad Bearing Condition-Monitoring Algorithm For Use With An Onboard Wireless Low-Power Sensor Module, Jonas Regan Leano Cuanang

Theses and Dissertations

An algorithm that utilizes vibration measurements was developed by the UTRGV Center for Railway Safety to monitor the condition of railroad bearings. This algorithm uses the data collected from accelerometers on the bearing adapters to determine if there is a defect, where the defect is within the bearing, and the approximate size of the defect. Laboratory testing was performed on the UTCRS single bearing test rig. A four-second sample window of the recorded vibration data is used by the algorithm to reliably identify the defective component inside the bearing with up to a 100% confidence level. However, considerable computational power …

Effect Of Adding Palm Fiber To Thermal Conductivity Of Quick Set Concrete, Monica Garcia

Theses and Dissertations

As climate change becomes a more dire issue and more readily accepted by those in power, the demand for local and systemic solutions grows louder. In urban environments, one issue of concern is the contribution of anthropogenic heat from buildings which contributes to localized warming of the environment. A method that can reduce anthropogenic heat is decreasing the thermal conductivity of building materials. The objective of this study is to examine the possibility of using palm fibers to reduce the thermal conductivity of quick-set concrete samples. The data gathered in this study are used to determine the thermal conductivity value …

The Design, Fabrication, And Testing Of A Cooling Garment, Richard James Garza

Theses and Dissertations

The aim of this research is to design a device or technology capable of cooling the user – such as a college student walking to class, for example – in a manner as convenient as putting on a jacket. The idea is to use the peltier effect – a phenomenon in which two dissimilar semi-conductors heat up and cool down with the application of an electric current – as the source of heat absorption used to cool the user. In this research it will be determined whether or not it is feasible to use such a phenomenon to keep the …

Assessing The Performance Of Reconditioned Railroad Tapered-Roller Bearings Used In Freight Rail Service, Veronica Valeria Hernandez

Theses and Dissertations

The rail industry currently utilizes two wayside detection systems to monitor the health of freight railcar bearings in service: The Trackside Acoustic Detection System (TADS™) and the wayside Hot-Box Detector (HBD). Bearings that are removed from service are sent to specialized facilities where they undergo a reconditioning process before the bearings can be returned to rail service. The reconditioning process has been used for decades although there has been no previous study on the effectiveness of the reconditioning process on defective bearings that were removed from service. This persuaded the researchers from the University Transportation Center for Railway Safety (UTRCS) …

Vibration Analysis Of Simultaneous Drilling And Reaming Bha, Mohammed F. Al Dushaishi, Daniel S. Stutts

Mechanical and Aerospace Engineering Faculty Research & Creative Works

The drillstring used in the oil and gas exploration is a complex structure due to the different forces acting on it. One of the primary sources of drillstring vibrations is the cutting forces caused by the drill bit contact with the rock formation. In some drilling applications, such as hole enlargement and underreaming, the source of the cutting action originates from the drill bit as well as the reamer which increases the dynamic complexity of the drillstring. This paper’s objective is to investigate the torsional vibration behaviors of the bottom hole assembly (BHA) under simultaneous drilling and reaming. More specifically, …

Modeling And Analysis For Unit Cell Size, Material Anisotropy And Material Imperfection Effects Of Cellular Structures Fabricated By Powder Bed Fusion Additive Manufacturing., Yan Wu

Electronic Theses and Dissertations

Cellular structures are networks of interconnected struts or walls with porosities and are widely found in many natural load-bearing structures such as plants and bones. Cellular structures offer unique functional characteristics such as high stiffness to weight ratio, tailorable heat transfer coefficient, and enhanced mechanical energy absorption, which makes them highly attractive in various engineering disciplines such as biomedical implants, electrodes, heat exchangers, and lightweight structures. There exists an abundance of literatures that have investigated various mechanical properties of various cellular structures such as Poisson’s ratio, elastic modulus, ultimate strength, yield strength, and failure characteristics. Based on the classic cellular …

Development Of A Pediatric Cardiac Assist Maglev Pump For Use With A Universal Driver System., Landon Heath Tompkins

Electronic Theses and Dissertations

Heart failure (HF) remains the leading cause of death, affecting 26 million adults worldwide and 6.5 million adults in the United States. Pediatric HF patients have been a historically underserved population with few options for mechanical circulatory support (MCS) therapy, a leading treatment as an alternative to heart transplantation. To address this clinical need, the Inspired Universal MagLev System is being developed; a low cost, universal magnetically levitated extracorporeal MCS system with interchangeable single-use pumps that will ultimately provide adult and pediatric patients ventricular and respiratory assist therapies. The Inspired Pediatric VAD is the first single-use pump application for this …

Finite Element Analysis Of Total Knee Arthroplasty, Sean Yueh

Master's Theses

The total knee arthroplasty (TKA) has become one of the most successful procedures in all of medicine, with an average of over 966,000 operations performed a year. Since its introduction in 1968, the TKA’s surgical process and implant designs have continuously been improved to increase survivability. However, the need for a revision TKA – due to aseptic loosening – continues to be a problematic aspect of the procedure. Stress shielding induced by different design parameters of the implant has generated controversy in the determination of an ideal configuration. The purpose of this study is to investigate how implant design parameters …

Improvement Of Labyrinth Seal Leakage Rates Using Additive Manufacturing, Austin L. Gasbarra

Master's Theses

The growing popularity of additive manufacturing in commercial applications has al- lowed for new ideas and new ways of thinking when designing components. Further optimization at the component level is possible, though powder metallurgy is in its infancy. This study explores the possibility of using additive manufacturing to develop better labyrinth seals in turbomachinery. Labyrinth seals have a torturous fluid path with high losses, thus limiting the amount of fluid leakage. These types of seals can be non-rotating, allowing them to better take advantage of the additive manufacturing process due to the absence of rotating stresses. Labyrinth seal performance is …

Characterization Of A Packaged Triboelectric Harvester Under Simulated Gait Loading For Total Knee Replacement, Nabid Aunjum Hossain, Geofrey George Yamomo, Ryan Willing, Shahrzad Towfighian

Mechanical Engineering Faculty Scholarship

Load sensing total knee replacement (TKR) implants are useful tools for monitoring prosthesis health and providing quantitative data to support patient claims of pain or instability. Powering such devices throughout the entire life of the knee replacement, however, is a challenge, and selfpowered telemetry via energy harvesting is an attractive solution. Herein, we implemented vertical contact mode triboelectric energy harvesters inside a knee implant package to generate the power required for embedded digitization and communications circuitry. The harvesters produce small-scale electric power from physiologically relevant loads transmitted through the knee. Experiments were performed on a joint motion simulator with an …

Electromagnetic Interference Shielding Effectiveness Of Interlayered Systems Containing Metal-Oxide, Conducting Polymer And Carbon Nanotube Reinforced Polymeric Composites, Shaik Merkatur Hakim Marjuban

Theses and Dissertations

The Electromagnetic Interference (EMI) Shielding Effectiveness (SE) has become one of the important requirements for the devices associated with telecommunication systems consisting of large frequency bands. The degradation of the quality of transmitting signal influenced by frequencies emitting from external sources can be reduced by covering the circuits of the devices by EMI Shielding materials like polymer composites, metal-based nanofiber mats, the metal of oxide films, etc. The investigation strives for the attenuation of EMI by introducing two composite mats from conducting polymer-based, multiwalled carbon nanotubes (MWCNTs) coated Nylon 6 nanofiber composites. Two other composite mats are also developed by …

Me-Em Enewsbrief, October-December 2020, Department Of Mechanical Engineering-Engineering Mechanics, Michigan Technological University

Department of Mechanical and Aerospace Engineering eNewsBrief

No abstract provided.

Optimizing Energy Power Consumption Of Freight Railroad Bearings Using Experimental Data, Carlos Eliasar Lopez Iii

Theses and Dissertations

Throughout the railway industry, trains use systems that record total energy efficiency of a train but not energy efficiency or consumption by components. Monitoring freight bearing power consumption can support the railroad industry efforts to maintain the railroad economic competitiveness and minimize the environmental impact.

For more than a decade now, the University Transportation Center for Railway Safety (UTCRS) at the University of Texas Rio Grande Valley (UTRGV) has been collecting power consumption data for railroad bearings under various loads, speeds, ambient temperatures, bearing condition, and bearing classes. Specifically, data such as temperatures, voltages, speed, and load were collected to …

Water-Soluble Polymers With Ceramic/Metal Nanoparticles For Use As Anode Materials In Lithium-Ion And Sodium-Ion Batteries, Roberto Orrostieta Chavez

Theses and Dissertations

Aqueous solutions of poly(vinylpyrrolidone) (PVP) with 20, 25, and 28 wt.% concentrations were successfully spun into fibers by centrifugal spinning. The pristine PVP fibers were annealed and carbonized to produce flexible carbon fibers for use as binder-free anodes in lithium-ion and sodium-ion batteries. These flexible carbon fibers were prepared by developing a novel three-step heat treatment to reduce the residual stresses in the pristine PVP precursor fibers and to prevent fiber degradation during carbonization. The average diameters of the pristine, annealed, and carbonized fibers were obtained using scanning electron microscopy (SEM), which showed that the average diameter of the carbon …

A Modified Peng-Robinson Cubic Equation Of State Based On Bayesian Framework, Wei Chen

Theses and Dissertations

Peng-Robinson cubic equations of state (PR-EoSs) as one of the most popular two-parameter cubic equations of state (2P-EoSs) are widely used to calculate thermodynamic properties of pure substances and their mixtures. However, the prediction accuracy of 2P-EoSs varies significantly among different substances due to its intrinsic limitation. To this end, many modifications have focused on changing the dependence structure of 𝛼 function with temperature for PR-EoS to enhance prediction accuracy. In this paper, we propose a Bayesian framework to calibrate a new 𝛼 function, which is a bias-corrected parametrized model form for the PR-EoS. The developed PR-EoS with the calibrated …

Investigating The Presence Of Culture In Engineering Design: A Case Study On Culture In Design Methods, Perception, And Outcomes, Malena Ataa Durowaah Agyemang

All Dissertations

Overwhelming global statistics on economic, social, and health disparities has driven engineers and designers to develop solutions to minimize these disparities [1,2,11,12,3–10]. For the scope of this study, these efforts are referred to as design for humanitarian engineering and global development (HEGD). HEGD solutions are designed to improve access to medical technologies, energy, clean water, and even spark economic development [1–10]. However, many HEGD solutions go unadopted, halting their intended benefits [9,13,22,23,14–21]. Efforts to improve HEGD adoption have focused on ways to incorporate culture in the design solution’s aesthetics or in approaches post-deployment [24,25,34,35,26–33]. However, a review of failed HEGD …

Molecular Mechanisms And Design Of Hydrogen-Bonded Materials For Thermal Applications, Jinlong He

All Graduate Theses and Dissertations, Spring 1920 to Summer 2023

Heat transfer at the nanoscale plays an important role in determining the reliability and performance of many innovative advanced materials technologies such as nanoelectronics, semiconductor, biomedical devices, polymers, and composites. Extensive efforts have been made to design materials with extraordinary thermal properties. However, fundamental understanding of heat transfer in many of these materials is still not lacking, because the thermal transport processes are governed by several factors including molecular morphology and chemical bonding. Among these factors, the atomic bonding between two dissimilar materials or within single materials is of particular interest due to its ubiquity and importance in physical processes. …

A.C. Moyer Eye-Cap Manufacturing, Thais Bertolus, Alexa Steidl, Hana Welsh, Jarod Kinney, Maya Willis

Mechanical Engineering

A.C. Moyer company has been making eye caps as a family business since 1947. Eye caps are a product used during the embalming process. Currently the machines being used to produce the eye caps are outdated and unsafe. We are a team of 5 mechanical engineering students tasked with either designing new machines or updating the existing machines to make the manufacturing process more efficient, automated, and safer. This document describes the design process, provides background, relevant research, establishes project objectives, and defines plans for project implementation.

Development Of Nirs Based Noninvasive Cerebrovascular Regulation Assessment, Stephanie Marie Miller

Theses and Dissertations

Alterations to cerebral blood flow (CBF) have been implicated in diverse neurological conditions, including mild traumatic brain injury, microgravity induced intracranial pressure (ICP) and intraocular pressure (IOP) increases, and mild cognitive impairment. Near infrared spectroscopy (NIRS)-measured regional cerebral tissue oxygen saturation (rSO2) provides an estimate of oxygenation of the interrogated cerebral volume that is useful in identifying trends and changes in oxygen supply to cerebral tissue and has been used to monitor cerebrovascular function during surgery and ventilation. In this study, CO2-inhalation-based hypercapnic breathing challenges were used as a tool to simulate CBF dysregulation, and NIRS was used to monitor …

The Optimization Of Efficiency And Infrastructure For Modern Potable Water Treatment Plants, Brent A. Dekock

Theses and Dissertations

The USDOE Industrial Assessment Centers (IACs) is a program that is designed to help small and medium-sized manufacturing facilities reduce their overall costs and improve energy efficiency. This includes improving potable water treatment plants which supply water throughout the country. This thesis covers the process of how IAC branches and water treatment facilities generally operate, as well as several assessment recommendations that have been developed by a branch of the IAC for several water treatment plants based in the Rio Grande Valley of Texas. The steps of the assessment and water treatment process are described, and several cost saving measures …

Modular Framework For Implementation And Analysis Of Recursive Filters With Considered And Neglected Parameters, Kyle J. Demars, Kari C. Ward

Mechanical and Aerospace Engineering Faculty Research & Creative Works

This paper develops novel covariance and square-root factor formulations of a consider-neglect Kalman filter for navigation applications. The proposed filter partitions system parameters into three distinct categories: those to be estimated by the filter, those whose contribution to the system are considered without being explicitly estimated, and those with sufficiently low effect on the system such that their contribution can be neglected altogether. Discussion on appropriate selection of parameters to be considered and neglected is provided with specific attention given to descent-to-landing navigation. Monte Carlo simulations and analysis are performed to assess the performance of the developed square-root consider-neglect filter …

Additive Manufacturing-Enabled Design, Manufacturing, And Lifecycle Performance, Tao Peng, Yi Zhu, Ming Leu, David Bourell

Mechanical and Aerospace Engineering Faculty Research & Creative Works

No abstract provided.

Synthesis And Characterization Of Non-Pgm Catalysts For Fuel Cell Applications, Sudharsan Sridhar

Masters Theses

Fuel Cells convert the chemical energy of a fuel and an oxidizing agent into electricity through a pair of redox reactions. Proton Exchange Membrane (PEM) fuel cells convert (efficiency-60%) hydrogen and air to power the electric motors with zero emissions, facilitating the development of environmentally friendly and sustainable automobile technologies. One of the major obstacles for larger commercial viability of Fuel Cells for automobile applications is their cost-effectiveness. Currently, fuel cells use platinum as a catalyst material, which is prohibitively expensive for commercial automobile applications. The development of non-Platinum Group Metal (non-PGM) catalyst materials with similar electrochemical performance to that …