Mechanical Engineering Commons^™

Experimental And Numerical Simulation Of Split Hopkinson Pressure Bar Test On Borosilicate Glass, Mayank K. Bagaria

Dissertations, Master's Theses and Master's Reports

This study is an extension to the design of ceramic materials component exposed to bullet impact. Owing to the brittle nature of ceramics upon bullet impact, shattered pieces behave as pellets flying with different velocities and directions, damaging surrounding components. Testing to study the behavior of ceramics under ballistic impact can be cumbersome and expensive. Modeling the set-up through Finite Element Analysis (FEA) makes it economical and easy to optimize. However, appropriately incorporating the material in modeling makes laboratory testing essential. Previous efforts have concentrated on simulating crack pattern developed during 0.22 caliber pellet impact on Borosilicate glass. A major …

Automotive Driveline Backlash State And Size Estimator Design For Anti-Jerk Control, Kaushal Kumar Darokar

Dissertations, Master's Theses and Master's Reports

Vehicle drivability is an important factor which more and more customers have started assessing before buying a vehicle. Customers carry out this assessment based on both vehicle reviews/ratings and based on the test drives. One of common maneuver which a customers perform during the test drive is sudden accelerator pedal tip-in or tip-out to accelerate or coast the vehicle. Clunk and shuffle are the phenomena that usually occur during this scenario causing driver discomfort. The clunk and shuffle are caused by the backlash and compliance physical properties of the driveline. Consequently, control strategy needs to be developed which can provide …

A Hybrid-Powered Wireless System For Multiple Biopotential Monitoring, Shawn Li

Dissertations, Master's Theses and Master's Reports

Chronic diseases are the top cause of human death in the United States and worldwide. A huge amount of healthcare costs is spent on chronic diseases every year. The high medical cost on these chronic diseases facilitates the transformation from in-hospital to out-of-hospital healthcare. The out-of-hospital scenarios require comfortability and mobility along with quality healthcare. Wearable electronics for well-being management provide good solutions for out-of-hospital healthcare. Long-term health monitoring is a practical and effective way in healthcare to prevent and diagnose chronic diseases. Wearable devices for long-term biopotential monitoring are impressive trends for out-of-hospital health monitoring. The biopotential signals in …

Closed Loop Energy Maximizing Control Of A Wave Energy Converter Using An Estimated Linear Model That Approximates The Nonlinear Froude-Krylov Force, Yaqzan Mohd Yaqzan

Dissertations, Master's Theses and Master's Reports

Wave energy converters (WECs) exploit ocean wave energy and convert it into useful forms such as electricity. But for WECs to be successful on a large scale, two primary conditions need to be satisfied. The energy generated must satisfy the network requirements, and second, energy flow from waves to the grid needs to be maximized. In this dissertation, we address the second problem. Most control techniques for WECs today use the Cummins' linear model to simulate WEC hydrodynamics. However, it has been shown that under the application of a control force, where WEC motions are amplified, the linear model diverges …

Influence Of Micro-Nucleate Boiling On Annular Flow Regime Heat Transfer Coefficient Values And Flow Parameters – For High Heat-Flux Flow Boiling Of Water, Soroush Sepahyar

Dissertations, Master's Theses and Master's Reports

Analysis of results from steady and steady-in-the-mean high heat-flux (15 - 70 W/cm², with water as working fluid) shear driven annular flow-boiling experiments presented here - and low heat-flux (0.1- 1 W/cm², with FC-72 as working fluid) experiments presented elsewhere – together lead to a key conclusion. The conclusion is that heat carrying nucleation rates go often undetected by the typically used visualization approaches for flow boiling – as such flows often involve µm- to sub- µm scale bubble diameters in millimeter-scale ducts. These nucleation rates play a significant role in most of the so-called convective …

Experimental Characterization Of Hydraulic System Sound, Ben Kolb

Dissertations, Master's Theses and Master's Reports

The purpose of this research was to establish test methods for characterizing the interaction between the hydraulic fluid and hydraulic hose at clipping points in mobile heavy equipment hydraulic systems. A simple hydraulic circuit test bench was developed and the laboratory axial piston pump was characterized using ISO 10767-1. A direct relationship between the fluidborne noise and structureborne noise present at each hose clip location was observed for a specific operating condition using operating deflection shapes and structureborne noise measurements. This result shows that optimal hose clip placement can be a viable solution to structureborne noise reduction. Additionally, a modal …

Multi-Scale, Capillary Assisted Copper Surfaces For Enhanced Pool Boiling Heat Transfer Processes, Chetan Agarwal

Dissertations, Master's Theses and Master's Reports

Phase-change heat transfer through pool boiling process offers a promising thermal management solution in applications wherein conventional air or single-phase liquid-based cooling methods prove inefficient such as for high-power electronics. Pool boiling process, which utilizes the latent heat of evaporation, provides a robust and efficient way to efficiently dissipate the excessive heat generated in a small footprint area in particular as seen in CPUs (Central Processing Units), GPUs (Graphics Processing Units), LEDs (Light Emitting Diodes), radars, and other demanding computing, sensing and surveillance electronics. Although boiling process has been studied for over five decades, it has not been yet adapted …

Estimation And Prediction Of The Human Gait Dynamics For The Control Of An Ankle-Foot Prosthesis, Guilherme Aramizo Ribeiro

Dissertations, Master's Theses and Master's Reports

With the growing population of amputees, powered prostheses can be a solution to improve the quality of life for many people. Powered ankle-foot prostheses can be made to behave similar to the lost limb via controllers that emulate the mechanical impedance of the human ankle. Therefore, the understanding of human ankle dynamics is of major significance. First, this work reports the modulation of the mechanical impedance via two mechanisms: the co-contraction of the calf muscles and a change of mean ankle torque and angle. Then, the mechanical impedance of the ankle was determined, for the first time, as a multivariable …

Using Frequency Based Substructuring To Optimize Multi-Axis Resonant Plate Shock Tests, Erica M. Jacobson

Dissertations, Master's Theses and Master's Reports

Resonant plate pyroshock tests only offer to test one component axis at a time, while the qualification pyroshock tests often have three single-axis specifications to meet. There is an interest in creating a multi-axis test environment from the single-axis resonant plate parts to save testing time, create a more realistic test environment, and monitor the possibility of an overtest. To investigate this, LaGrange-multiplier frequency based substructuring was implemented to virtually arrange the single-axis resonant plate subsystems into different assembly configurations and mathematically calculate the new assembly dynamics. A shock response spectrum was calculated from the new assembly dynamics through an …

Development Of A Fused Deposition 3d Printed Buoy And Method For Quantifying Wave Tank Reflections, Samantha G. Swartzmiller

Dissertations, Master's Theses and Master's Reports

Testing model scale prototypes is integral to the development of wave energy converter (WEC) technology. Model scale WECs are tested in wave tanks where they are subjected to repeatable wave fields. Their presence in water creates radiated waves that eventually reflect off tank walls disrupting the intended wave field. Fabrication of model scale WECs is another developing aspect of tank testing. Often model WECs are built of foam. Additive manufacturing is a promising alternative although the most common method, fused deposition modeling (FDM) 3D printing, does not typically produce waterproof parts. The goals of this work were 1) develop a …

High Injection Pressure Dme Ignition And Combustion Processes: Experiment And Simulation, Xiucheng Zhu

Dissertations, Master's Theses and Master's Reports

With nearly smokeless combustion, Dimethyl Ether (DME) can be pressurized and used as a liquid fuel for compression-ignition (CI) combustion. However, due to its lower heating value and liquid density compared with diesel fuel, DME has a smaller energy content per unit volume. To obtain an equivalent energy content of diesel, approximately 1.86 times more quantity of DME is required. This can be addressed by a larger nozzle size or higher injection pressure. However, the effect of high injection pressure on DME spray combustion characteristics have not yet been well understood. In order to fill this gap, spray and combustion …

Optimization And Control Of Arrays Of Wave Energy Converters, Jianyang Lyu

Dissertations, Master's Theses and Master's Reports

Wave Energy Converter Array is a practical approach to harvest ocean wave energy. To leverage the potential of the WEC array in terms of energy extraction, it is essential to have a properly designed array configuration and control system. This thesis explores the optimal configuration of Wave Energy Converters (WECs) arrays and their optimal control. The optimization of the WEC array allows both dimensions of individual WECs as well as the array layout to varying. In the first optimization problem, cylindrical buoys are assumed in the array where their radii and drafts are optimization parameters. Genetic Algorithms are used for …

Analytical Modeling And Life Cycle Assessment Of A Solar Powered Vapor Absorption Cooling System, Harold A. Walters

Electronic Theses and Dissertations

Vapor absorption cooling systems (VACS) offer an environmentally friendly alternative to the standard vapor compression cooling systems (VCCS) for cooling homes, businesses, factories, and other buildings. VACS use low-grade thermal energy to achieve a cooling effect and require minimal electrical input for the liquid solution pump used for circulation within the system. The thermal energy which powers these systems can be provided through several means; one popular form is through the use of solar thermal collectors. This paper provides a process for determining the overall size and configuration of the VACS depending upon the operating conditions of selected components. A …

Gnss/Lidar-Based Navigation Of An Aerial Robot In Sparse Forests, Antonio C. Chiella, Henrique N. Machado, Bruno O.S. Teixeira, Guilherme A.S. Pereira

Faculty & Staff Scholarship

Autonomous navigation of unmanned vehicles in forests is a challenging task. In such environments, due to the canopies of the trees, information from Global Navigation Satellite Systems (GNSS) can be degraded or even unavailable. Also, because of the large number of obstacles, a previous detailed map of the environment is not practical. In this paper, we solve the complete navigation problem of an aerial robot in a sparse forest, where there is enough space for the flight and the GNSS signals can be sporadically detected. For localization, we propose a state estimator that merges information from GNSS, Attitude and Heading …

Cmas/Volcanic Ash Infiltration Performance Of Yttria Rich-Zirconia Thermal Barrier Coatings Produced By Electron Beam Physical Vapor Deposition, Juan Jose Gomez Chavez

Open Access Theses & Dissertations

For many years the use of thermal barrier coatings (TBC) in gas turbine engines has allowed a significant increase in engine operating temperatures which are above the Ni-based super alloys' melting point. The base material for TBCs is the state of the art 7 wt % yttria stabilized zirconia (YSZ) which provides the thermal protection. Current industry demands for increased engine efficiency has pushed TBCs to the limits where significant technological constrains have been identified. One of the main ones represents the high temperature corrosion of the TBC material due to the ingestion of silicate based airborne particles commonly referred …

Advanced Design And Manufacturing Of Composite High-Powered Rockets, Matthew Whitfield

Honors Theses

This thesis covers aspects related to the design and manufacturing of high-powered composite competition rockets. Research related to the project was performed over the course of three years of participation on the University of Mississippi Rocket Rebels competition team. Areas of the project covered include project definition, rocket design, and rocket manufacturing. Project definition covers how to build a team, select a competition, and establish communication, among others. The rocket design portion discusses the work that goes into meeting competition performance requirements, and includes simulations from the 2018-19 Rocket Rebels rocket. The rocket manufacturing portion includes a summary of manufacturing …

Numerical Study On The Dynamic Process Of Single Plume Flow In Thermal Convection With Polymers, Jian-Ping Cheng, Wei-Hua Cai, Hong-Na Zhang, Feng-Chen Li, Lian Shen, Shi-Zhi Qian

Mechanical & Aerospace Engineering Faculty Publications

A direct numerical simulation of single plume flow in thermal convection with polymers was carried out in a domain with 1:3 as the width to height ratio. The heat transport ability is weakened by adding polymers within the here-investigated governing parameter range. However, it is promoted when the maximum polymer extension L is increased. The distribution of vertical velocity and temperature indicates that the plume in the polymer solution case is speeded up and widens bigger as compared to that in the Newtonian fluid case. Inside the plume, polymer chains tend to release energy at the position where the …

Nebraska Summary: S1178 Fendt 933, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Effects Of Lubrication Starvation On Flash Temperature For Thermal Mixed Elastohydrodynamic Gear Contacts, Danielle D. Massé

Browse all Theses and Dissertations

Lubrication is provided to the gear trains in automotive and aerospace transmission systems to prevent mechanical contact through the formation of a full lubricant film, which in turn removes heat generated at the gear contact surfaces. When debris blocks the inlet nozzle, the flow of lubricant is restricted and mechanical components experience lubrication starvation. Under starved lubrication the temperatures of the contact surfaces become elevated which can lead to the formation of a weld between them, a catastrophic failure mode called scuffing. For spur gears, the occurrence of scuffing is due to high sliding in the vicinity of the root …

Rasters Vs Contours For Thin Wall Ultem 9085 Fdm Applications, Vausman Kota

Browse all Theses and Dissertations

Currently many components are additively manufactured via fused deposition modeling (FDM). However, FDM results in gaps between passes which produces a poor surface finish and porous material that is difficult to hold pressure. Commercial scale air systems require a pressure to be maintained within thin walled components with minimal post processing and clean up after fabrication. A design of experiments (DOE) was created to identify the optimal raster vs contour ratio for UTLEM 9085 CG fabricated using FDM at different build angles and wall thicknesses. A custom-built pressurized test system was developed, the leak rates were calculated and the surfaces …

A Biomimetic Approach To Controlling Restorative Robotics, Matthew T. Boots

Graduate Theses, Dissertations, and Problem Reports (ETD)

Movement is the only way a person can interact with the world around them. When trauma to the neuromuscular systems disrupts the control of movement, quality of life suffers. To restore limb functionality, active robotic interventions and/or rehabilitation are required. Unfortunately, the primary obstacle in a person’s recovery is the limited robustness of the human-machine interfaces. Current systems rely on control approaches that rely on the person to learn how the system works instead of the system being more intuitive and working with the person naturally. My research goal is to design intuitive control mechanisms based on biological processes termed …

Numerical Investigation And Optimization Of Pin Fins In Micro Heat Sinks, Fuad Ismayilov

Electronic Theses and Dissertations

Operating temperature in electronics applications is continuously increasing. Therefore, for the past few decades, high heat flux removing micro heat sinks are investigated in terms of heat transfer effectiveness. This study generally concentrates on improving the passive heat transfer techniques. Micro heat sinks used in experiments are fabricated using MEMS techniques. Resistance temperature detectors, RTDs, were used for temperature measurements. The experimental data was obtained for single and two phase flow regions; however, only single phase flow results were considered in numerical simulations. Numerical validations were performed on the micro heat sinks, including cylinder and hydrofoil shaped pin fins. Following …

Fluid Flow Characteristics Of A Co-Flow Fluidic Slot Jet Thrust Augmentation Propulsion System, Brian Garrett

Electronic Theses and Dissertations

The UAV industry is booming with investments in research and development on improving UAV systems in order to increase applications and reduce costs of the use of these machines. Current UAV machines are developed according to the quadcopter design which has a rotary propulsion system which provides the lift needed for the aerial vehicles. This design has some flaws; namely safety concerns and noise/vibration production both of which come from the rotary propulsion system. As such, a novel propulsion system using slip stream air passed through high performance slot jets is proposed and analysis of the fluid characteristics is presented …

A Study Of Organo-Phosphorous Simulants Thermal Destruction Using Shock Tube/Laser Diagnostics Techniques And Chemical Kinetics Modeling, Sneha Neupane

Electronic Theses and Dissertations

High-fidelity chemical kinetic models are critical in predictive modeling during design and optimization of next generation energy systems. Shock tube provides an ideal tool to investigate high-temperature chemical kinetics. Non-intrusive laser absorption diagnostics provide in-situ measurements of quantitative, time-resolved species concentration data in this complex chemically reacting system. In this work, shock tube and laser absorption spectroscopy were utilized to measure species concentration time-histories during pyrolysis and oxidation of organo-phosphorous compounds (OPCs). The experiments data obtained were used as benchmark to develop an improved kinetic model of OPCs combustion. Interest in combustion chemistry of OPCs is associated to their use …

Employing 2-D Cfd & Lrb Model Around Trees To Improve Vawt Placement, David Chukwuebuka Bassey

All Graduate Theses, Dissertations, and Other Capstone Projects

In the placement of vertical axis wind turbines, trees are a constant presence in the vicinity. They are found to grow at different height and shape configurations. And in areas such as the Minnesota State University, Mankato (MNSU) campus, they serve as blockage to airflow; limiting the efficiency of installed turbines. This work sets the precedent for the validation of vegetative numerical models created for the Xcel Energy Research Development Fund (RDF) project.

Using two-dimensional (2-D) numerical simulations of porous cylinders placed in a rectangular medium of air, insight into the flow profile and distribution in the leeward side of …

Study Of American Wood Pellet Stove Emissions, Sergio Gamarra

All Graduate Theses, Dissertations, and Other Capstone Projects

Problem: The EPA (Environmental Protection Agency) had not specified emissions performance standards for pellet burning stoves. Instead they were lumped in with cordwood burning stoves. IRETI’s decision to pursue this baseline study was guided by Minnesota’s concurrent “2025 Energy Action Plan” and the EPA’s pellet stove testing method development. Wood pellet fuel, a renewable resource, and the technology developed to utilize it for residential heating should be further studied to examine how together they both stand up to newly developed EPA emissions testing methods. This will establish a benchmark for testing American technology, thus guiding IRETI’s efforts of introducing foreign …

Development Of Physics Based Machine Learning Algorithms, Rob Jennings

Master’s Theses

In this study, a baseball pitch was examined to try to understand its behavior, and make a predictive model of it. A baseball pitch was tested experimentally with a wind tunnel and modeled computationally with COMSOL CFD software. Five input variables (spin rate, sting angle, seam orientation: Y axis, seam orientation: Z axis, and air velocity) were controlled, with force in three axes recorded as outputs. The experimental and computational results were examined and seen to be interdependent for all input variables. Experimental and computational data were both insufficient for predicting system behavior. Experimental data collection would have required an …

Solar Powered Atmospheric Water Generation, Ben Conser

Master’s Theses

Several atmospheric water generation (AWG) system configurations were analyzed to determine the feasibility of AWG as a method to combat water stress. In order to best combat water stress, AWG must be implemented in such a way which minimizes the energetic and monetary cost of water production. Thermodynamic and economic analyses were used to compare the performance of several AWG system configurations. Metrics such as specific energy consumption (SEC) and levelized cost of water (LCOW), which measure the energetic and monetary cost of water production respectively, were used to compare each system. Using this approach, the optimal system configuration was …

Analysis And Control Of Fiber-Reinforced Elastomeric Enclosures (Frees), Soheil Habibian

Master’s Theses

While rigid robots are extensively used in various applications, they are limited in the tasks they can perform and can be unsafe in close human-robot interactions. Soft robots on the other hand surpass the capabilities of rigid robots in several ways, such as compatibility with the work environments, degrees of freedom, manufacturing costs, and safe interactions with the environment. This thesis studies the behavior of Fiber-Reinforced Elastomeric Enclosures (FREEs) as a particular type of soft pneumatic actuator that can be used in soft manipulators. A dynamic lumped-parameter model is created to simulate the motion of a single FREE under various …

Structures And Daq System For The Lox/Lch4 500 And 2000 Lbf. Rocket Engines, Rachel Pilgrim

Open Access Theses & Dissertations

With the progression of space exploration and research, new alternative fuels and fuel combinations have been discovered. The ability to produce methane from Mars' atmosphere and oxygen from Mars' regolith has led to the two becoming a great alternative propellant combination for rocket propulsion systems. To further advance LOX/LCH4 propulsion systems, a 500 and 2000 lbf rocket engine were designed and manufactured and are to be launched from the MIRO cSETR Technology Research and Innovation Acceleration Park (tRIAc) in Fabens, Texas for data collection and analysis. The objective of this thesis is to give a thorough overview of the static …