Mechanical Engineering Commons^™

Project Plan - Mentoring, Abigail Lisjak, Patrick Gray, Timothy Leonard, Adam Foster

Sustainability and Connectivity

A presentation that includes the ideal goal for the project as well as how the project can relate to the other projects in the class.

An Analytical Model To Predict The Length Of Oxygen-Assisted, Swirled, Coal And Biomass Flames, David Arthur Ashworth

Theses and Dissertations

Government regulations to reduce pollutants and increasing environmental awareness in the power generation industry have encouraged coal power plants to begin firing biomass in their boilers. Biomass generally consists of larger particles which produce longer flames than coal for a given burner. The length of the flame is important in fixed-volume boilers because of its influence on heat transfer, corrosion, deposition, and pollutant formation. Many pulverized fuel burners employ a series of co-annular tubes with various flows of fuel and air to produce a stabilized flame. A variable swirl burner with three co-annular tubes, each of variable diameter, has been …

Design Of A 3d Printable Mechanical Time Simulating Solar System Model For Use In Stem Education, Mark Bedford Moffett

Theses and Dissertations

The use of designed tools to assist with relating abstract ideas to reality is now a possibility with the use of the modern manufacturing method of 3D printing. The inner four planets’ natural orbital periods with respect to Earth were modeled in SolidWorks and then fabricated using 3D printing. A 3D printable mechanical time simulating solar system model used in science, technology, engineering, and mathematics (STEM) could assist with the user’s understanding of the history of science, planetary orbital mechanics, gearing ratios, 3D printing, and systematically constructing a project using instructions. This paper describes the design of a 3D printable …

2017 (Spring) Ensi Informer Magazine, Morehead State University. Engineering Sciences Department

ENSI Informer Magazine Archive

The ENSI Informer Magazine published in the spring of 2017.

Predictive Modeling Of A Buoyancy-Operated Cooling Tower Under Saturated Conditions - I: Adjoint Sensitivity Model, Dan Gabriel Cacuci, Federico Di Rocco

Faculty Publications

A cooling tower discharges waste heat produced by an industrial plant to the external environment. The amount of thermal energy discharged into the environment can be determined by measurements of quantities representing the external conditions, such as outlet air temperature, outlet water temperature, and outlet air relative humidity, in conjunction with computational models that simulate numerically the cooling tower's behavior. Variations in the model's parameters (e.g., material properties, model correlations, boundary conditions) cause variations in the model's response. The functional derivatives of the model response with respect to the model parameters (called "sensitivities") are needed to quantify such response variations …

Corgi: Compute Oriented Recumbent Generation Infrastructure, Christopher Allen Hunt

Master's Theses

Creating a bicycle with a rideable geometry is more complicated than it may appear, with today’s mainstay designs having evolved through years of iteration. This slow evolution coupled with the bicycle’s intricate mechanical system has lead most builders to base their new geometries off of previous work rather than expand into new design spaces. This crutch can lead to slow bicycle iteration rates, often causing bicycles to all look about the same. To combat this, several bicycle design models have been created over the years, with each attempting to define a bicycle’s handling characteristics given its physical geometry. However, these …

Me-Em Enewsbrief, March 2017, Department Of Mechanical Engineering-Engineering Mechanics, Michigan Technological University

Department of Mechanical and Aerospace Engineering eNewsBrief

No abstract provided.

Formation Of Mound-Like Multiscale Surface Structures On Titanium By Femtosecond Laser Processing, Edwin Peng, Alfred Tsubaki, Craig A. Zuhlke, Ryan Bell, Meiyu Wang, Dennis R. Alexander, George Gogos, Jeffrey E. Shield

Department of Mechanical and Materials Engineering: Dissertations, Theses, and Student Research

Surface Functionalization Technique • Femtosecond Laser Surface Processing (FLSP) • Utilize high power, femtosecond (10-15 s) laser pulses • Produce self-organized, multiscale surface micro/nanostructures • Diverse range of applicable substrates: semiconductors, metals, polymers, & composites

Why? • What are the different types of FLSP structures on Ti? • Physical evidence needed for FLSP formation models • Optimize FLSP of Ti for biomedical & other applications

How? • Obtain evidence of mound growth processes by examining underlying microstructure • Utilize dual beam Scanning Electron Microscope-Focused Ion Beam instrument to cross section surface structures & fabricate transmission electron microscopy samples

The Development Of A Vertical-Axis Wind Turbine Wake Model For Use In Wind Farm Layout Optimization With Noise Level Constraints, Eric Blaine Tingey

Theses and Dissertations

This thesis focuses on providing the means to use vertical-axis wind turbines (VAWTs) in wind farms as an alternative form of harnessing wind energy in offshore and urban environments where both wake and acoustic effects of turbines are important considerations. In order for VAWTs to be used in wind farm layout analysis and optimization, a reduced-order wake model is needed to calculate velocities around a turbine quickly and accurately. However, a VAWT wake model has not been available to accomplish this task. Using vorticity data from computational fluid dynamic (CFD) simulations of VAWTs and cross-validated Gaussian distribution and polynomial surface …

Binder-Jet Printing Of Fine Stainless Steel Powder With Varied Final Density, Mohsen Ziaee, Eric M. Tridas, Nathan B. Crane

Faculty Publications

Binder jetting is an additive manufacturing process that produces relatively weak porous parts that are strengthened through sintering and/or infiltration. This paper reports on two different methods of preparing fine 316 stainless steel powder and their impact on the final sintered density and dimensions relative to direct printing into -22 micron powder. The first method uses agglomerates of fine powder. In the second, nylon 12 powders are mixed with the steel powder as a fugitive space holder to increase porosity. Sintered density and sintering shrinkage of agglomerate material are shown to vary with the density of the spread powder bed. …

Assessing The Sunguide® And Steward Databases, Florida Solar Energy Center, Richard Raustad

FSEC Energy Research Center®

This report is a final research report for Assessing the SunGuide® and STEWARD Databases project of the Electric Vehicle Transportation Center (EVTC) at the University of Central Florida (UCF). The Electric Vehicle Transportation Center is a University Transportation Center funded by the Research and Innovative Technology Administration of the U.S. Department of Transportation. The EVTC is a research and education center whose projects prepare the U.S. transportation system for the influx of electric vehicles into a sustainable transportation network and investigate the opportunity these vehicles present to enhance electric grid modernization efforts. The EVTC is led by UCF's Florida Solar …

The Influence Of Bmss On The Characterization And Modeling Of Series And Parallel Li-Ion Packs, Sandra Castano-Solis, Daniel Serrano-Jimenez, Lucia Gauchia, Javier Sanz

Michigan Tech Publications, Part 1

This work analyzes the effects of a BMS (battery management system) on the characterization and modeling of series and parallel connections of Li-ion cell packs. The Li-ion pack studied consists of four series modules connected in parallel. This pack has been characterized by means of charge, discharge and frequency tests. As a result of these tests, series and parallel influence on battery parameters have been determined. A model considering the effects of a BMS is established and compared with a model based on a single-cell approach. Experimental validations show that the single cell based approach gives poor results in comparison …

Pv-Driven Heat Pump Water Heater Final Report, Florida Solar Energy Center, Carlos Colon

FSEC Energy Research Center®

As part of the effort towards zero energy buildings and high efficiency water heating systems, the Florida Solar Energy Center (FSEC) working under contract with the National Renewable Energy laboratories (NREL) has successfully completed a demonstration of a photovoltaic heat pump water heater (PV-HPWH) concept. The system integrates two 310Wp solar photovoltaics (PV) modules and grid tied micro-inverters with a commercially available 50-gallon HPWH. The project showcases innovative strategies for distributed PV thermal systems that limit grid interaction and provide increased thermal energy storage. The system utilizes a custom appliance control module (ACM) interface to vary thermostat settings (115 °F …

Electric Vehicle Charging Technologies Analysis And Standards, Florida Solar Energy Center, J. Doug Kettles

FSEC Energy Research Center®

This project has evaluated the technologies and standards associated with Electric Vehicle Service Equipment (EVSE) and the related infrastructure, and the major cost issue related to electric vehicle (EV) charging -- the cost of utility power. The technology assessment report evaluated safety standards for infrastructure, highway and vehicles and the barriers and challenges of deploying an expanded network of EV charging stations. The report also made recommendations to help standardize and expedite EVSE infrastructure and charging network deployment.

Persistent Operation Of Mobile Robots, Nina Mahmoudian

TechTalks

Success of numerous unmanned mobile missions in space, air, ground, and water is measured by the ability of the robots to usefully operate for extended time in dynamic and uncertain environments. This talk will provide an overview of the recent progress towards performing autonomous long-term missions. The approach includes task and energy routing scheduling, efficient path planning and coordination, and low-infrastructure platforms. The goal is to provide practical solutions by lowering deployment and operating costs, while also increasing efficiency, endurance and persistence during complex missions like disaster responses and long-term science discoveries.

Doe Apra-E Nextcar Program On Connected And Automated Vehicles In Collaboration With Gm, Jeffrey D. Naber

TechTalks

Within the $3.5M ARPA-e NEXTCAR program, Michigan Tech in collaboration with GM will development and demonstrate on a fleet of eight 2017 Chevrolet Volts and a mobile connected cloud computing center, a Vehicle Dynamics and Powertrain (VD&PT) model-based predictive controller (MPC) encompassing a real-time VD&PT dynamic model leveraging vehicle conductivity (V2X) with real-time traffic modeling and predictive speed horizons and eco-routing. The objective is to achieve a minimum of 20% reduction in energy consumption (electric + fuel) through the first ever real-time implementation and connection of route planning, powertrain energy management MPC algorithms. Connectivity data from vehicles, infrastructure, GPS, traffic …

Cost Effectiveness Of Energy Efficiency And On-Site Photovoltaic Power For 2015 International Energy Conservation Code Eri (Energy Rating Index) Compliance, Florida Solar Energy Center, Philip W. Fairey

FSEC Energy Research Center®

EnergyGauge® USA v.5.1 is used to simulate the energy use of one-story, three bedroom, 2000 ft², single-family, frame homes in sixteen representative U.S. climates comprising all eight IECC climate zones. The energy use of the Section R406.2 minimum efficiency home (the Baseline Home) is compared against the energy use of homes complying with the prescriptive requirements of Section R402 of the 2015 IECC and against homes complying with the Section R406 Energy Rating Index (ERI) Compliance Alternative. The improvement cost and energy savings of the improved homes relative to the Baseline Home are then used to determine the cost effectiveness …

Phonon Interference In Crystalline And Amorphous Confined Nanoscopic Films, Zhi Liang, Thomas E. Wilson, Pawel Keblinski

Mechanical and Aerospace Engineering Faculty Research & Creative Works

Using Molecular Dynamics Phonon Wave Packet Simulations, We Study Phonon Transmission Across Hexagonal (H)-BN and Amorphous Silica (A-SiO₂) Nanoscopic Thin Films Sandwiched by Two Crystalline Leads. Due to the Phonon Interference Effect, the Frequency-Dependent Phonon Transmission Coefficient in the Case of the Crystalline Film (Si|h-BN|Al Heterostructure) Exhibits a Strongly Oscillatory Behavior. in the Case of the Amorphous Film (Si|a-SiO₂|Al and Si|a-SiO₂|Si Heterostructures), in Spite of Structural Disorder, the Phonon Transmission Coefficient Also Exhibits Oscillatory Behavior at Low Frequencies (Up to ∼1.2 THz), with a Period of Oscillation Consistent with the Prediction from the Two-Beam …

Laser Shock Wave Assisted Patterning On Niti Shape Memory Alloy Surfaces, Dovletgeldi Seyitliyev, Peizhen Li, Khomidkhodza Kholikov, Byron Grant, Haluk E. Karaca, Ali O. Er

Mechanical Engineering Faculty Publications

An advanced direct imprinting method with low cost, quick, and less environmental impact to create thermally controllable surface pattern using the laser pulses is reported. Patterned micro indents were generated on Ni₅₀Ti₅₀ shape memory alloys (SMA) using an Nd:YAG laser operating at 1064 nm combined with suitable transparent overlay, a sacrificial layer of graphite, and copper grid. Laser pulses at different energy densities which generates pressure pulses up to 10 GPa on the surface was focused through the confinement medium, ablating the copper grid to create plasma and transferring the grid pattern onto the NiTi surface. Scanning …

Recoverable Stress Induced Two-Way Shape Memory Effect On Niti Surface Using Laser-Produced Shock Wave, Dovletgeldi Seyitliyev, Peizhen Li, Khomidkhodza Kholikov, Byron Grant, Zachary Thomas, Orhan Alal, Haluk E. Karaca, Ali O. Er

Mechanical Engineering Faculty Publications

The surfaces of Ni50Ti50 shape memory alloys (SMAs) were patterned by laser scribing. This method is more simplistic and efficient than traditional indentation techniques, and has also shown to be an effective method in patterning these materials. Different laser energy densities ranging from 5 mJ/pulse to 56 mJ/pulse were used to observe recovery on SMA surface. The temperature dependent heat profiles of the NiTi surfaces after laser scribing at 56 mJ/pulse show the partially-recovered indents, which indicate a "shape memory effect (SME)" Experimental data is in good agreement with theoretical simulation of laser induced shock wave propagation inside NiTi SMAs. …

Effect Of Sky Conditions On Light Transmission Through A Suspended Particle Device Switchable Glazing, Aritra Ghosh, Brian Norton, Aidan Duffy

Articles

A suspended particle device (SPD) switchable glazing changes its state from opaque to transparent in the presence of a power supply. SPD glazing's near normal transmission varies with incident angle and clearness index. Due to a lower diffuse component, higher glazing transmission ensues at higher clearness indices. Transmittance values for different azimuthal incident angle for a SPD glazing for its “transparent” and “opaque” states have been determined. In Dublin, below 0.5 clearness index, isotropic diffuse transmittance was prevailed while transmission of direct insolation was dominant above 0.5 clearness index. For south facing vertical plane SPD glazing transmittance in its transparent …

In-House Fabrication Of Temperature Sensitive Paint For Turbine Cooling Research, Mayur D. Patel, Mark A. Ricklick

Beyond: Undergraduate Research Journal

The Temperature Sensitive Paint (TSP) is a widely used method in measuring and visualizing flow separation and heat transfer. Compared to the cost and time consumption needed for methods such as pitot tubes, temperature sensitive paint is a cheaper alternative. Due to high usage in College of Engineering research projects, it was determined that in house fabrication of temperature sensitive paint would reduce time and cost limitations. For initial stages, literature research was performed to determine the recipe of intensity based TSP with luminophore and polymer binder that operated optimum at temperatures from 0-100°C. Europium III thenoyltrifluoroacetonate was determined to …

Mechanical Engineering News, Georgia Southern University

Mechanical Engineering: News & Publications (2013-2023)

• Nanotechnology and Cancer Exploratory Collaborative Symposium

Implications Of Electric Vehicle Penetration On State And Federal Highway Revenues, Florida Solar Energy Center, Kevin Schleith

FSEC Energy Research Center®

This report summarizes the results of research conducted to determine if current and near future electric vehicle (EV) sales will have an impact on motor fuel tax revenues as part of the Federal Highway Trust Fund (HTF). Gasoline and diesel fuel taxes account for $31.1 billion or about 87% of the HTF. The project results were accomplished by conducting a review of existing industry and government reports that detail fuel tax revenues and an analysis of EV sales from 2010 through 2016. Results show, that as of January 2017, the lost fuel tax revenue from EV sales of 560,000 vehicles …

Electric Vehicle Life Cycle Cost Analysis, Florida Solar Energy Center, Richard Raustad

FSEC Energy Research Center®

This project compared total life cycle costs of battery electric vehicles (BEV), plug-in hybrid electric vehicles (PHEV), hybrid electric vehicles (HEV), and vehicles with internal combustion engines (ICE). The analysis considered capital and operating costs in order to present an equal comparison of differing vehicles. The analysis also included photovoltaic (PV) and workplace charging options. The overall goal was to define the total vehicle cost of ownership over 5, 10, 15, and 20 year life expectancies. The developed life cycle cost computer program will allow any individual to compare life cycle costs of any vehicle.

In Vivo Pharmacological Evaluations Of Pilocarpine-Loaded Antioxidant-Functionalized Biodegradable Thermogels In Glaucomatous Rabbits, Shih-Feng Chou, Li-Jyuan Luo, Jui-Yang Lai

Mechanical Engineering Faculty Publications and Presentations

To alleviate oxidative stress-induced ocular hypertension, grafting of antioxidant molecules to drug carriers enables a dual-function mechanism to effectively treat glaucomatous intraocular pressure (IOP) dysregulation. Providing potential application for intracameral administration of antiglaucoma medications, this study, for the first time, aims to examine in vivo pharmacological efficacy of pilocarpine-loaded antioxidant-functionalized biodegradable thermogels in glaucomatous rabbits. A series of gallic acid (GA)-grafted gelatin-g-poly(N-isopropylacrylamide) (GN) polymers were synthesized via redox reactions at 20-50 °C. Our results showed that raising redox radical initiation reaction temperature maximizes GA grafting level, antioxidant activity, and water content at 40 °C. Meanwhile, increase in overall hydrophilicity of …

Collective Nonaffine Displacements In Amorphous Materials During Large-Amplitude Oscillatory Shear, Nikolai V. Priezjev

Mechanical and Materials Engineering Faculty Publications

Using molecular dynamics simulations, we study the transient response of a binary Lennard-Jones glass subjected to periodic shear deformation. The amorphous solid is modelled as the three-dimensional Kob-Andersen binary mixture at a low temperature. The cyclic loading is applied to slowly annealed, quiescent samples, which induces irreversible particle rearrangements at large strain amplitudes, leading to stress-strain hysteresis and a drift of the potential energy towards higher values. We find that the initial response to cyclic shear near the critical strain amplitude involves disconnected clusters of atoms with large nonaffine displacements. In contrast, the amplitude of shear stress oscillations decreases after …

A Vertical Axis Wave Turbine With Hydrofoil Blades, Yingchen Yang, Isaiah Diaz, Sergio Soto Quintero

Mechanical Engineering Faculty Publications

This work discusses a new wave energy converter (WEC) design that, when deployed in waves, performs unidirectional rotation about a vertical shaft. The uniqueness of this new WEC design is on utilizing omnidirectional water flow generated by waves to drive a rotor to perform unidirectional rotation about a vertical axis. This unique feature circumvents the frequency-dependent issue of common WECs, and eliminate realignment needs to cope with dynamically changing wave propagation directions. The key component of the WEC is a rotor, which has a vertical shaft with a number of blades mounted to it. Each blade has a hydrofoil-shaped cross …

Comparative Performance Of Two Ventilation Strategies In A Hot-Humid Climate, Florida Solar Energy Center, Sarah Widder

FSEC Energy Research Center®

ASHRAE Standard 62.2, 'Ventilation and Indoor Air Quality in Low-Rise Buildings,' is the most commonly referenced residential ventilation standard in the United States. It is currently required by ENERGY STAR Version 3 (V3), the 2012 International Energy Conservation Code, the U.S. Department of Energy's Zero Energy Ready Home Program, many state weatherization programs, and many other home performance programs. The standard calls for ventilation levels that are perceived by some builders and contractors to cause indoor moisture issues in hot-humid climates unless mitigated by supplemental dehumidification systems, which increase overall energy consumption. Therefore, many high-performance home builders in a hot-humid …

Skin Strain Measurement To Predict Knee Joint Angles Through Nanocomposite Stain Gauges, Adin Martineau, James Tracy, Gavin Collins, Parker Rosquist, Dustin A. Bruening, Matt K. Seeley, David T. Fullwood, Anton E. Bowden

Biomedical Engineering Western Regional Conference

Explores the possibility of using high deflection nanocomposite strain gauges as knee joint angle sensor.