Mechanical Engineering Commons^™

Low-Cost Inkjet Process For 3-D Printing, Christopher T. Schmitt

Mechanical Engineering Undergraduate Honors Theses

This paper presents a low-cost 3-D inkjet process design. Current commercially available 3-D inkjet printers (e.g., Objet Connex) that are capable of multi-material printing are expensive and out-of-reach of most consumers. While fused deposition modeling and other extrusion-based hybrid processes for multi-material printing are becoming available, these techniques are slow and relatively low-resolution. This research attempts to fill the gap by presenting a simple and low-cost solution to bring desktop 3-D inkjet to the community by utilizing components from an Epson inkjet printer. The mechanical system was designed with maximum utilization of the Epson carriage system with the addition of …

Influence Of Hydrogen Concentration And Distribution On Fracture In Nickel, Arturo Sucre Melfi

Mechanical Engineering Undergraduate Honors Theses

Hydrogen embrittlement is a main factor in the premature failure of metals under stress. Using molecular dynamics (MD) simulations, two models were built in order to study how the presence of hydrogen at interstitial positions within the nickel lattice affects how it fractures. The first model was a 3D single crystal nickel sample, while the other was the same nickel model but with different concentrations and locations of hydrogen positioned at or near the crack tip. Two aspects of fracture were studied and compared between the different simulations: the crack tip velocity and dislocation nucleation from the crack tip. Analysis …

Droplet Generation At Megahertz Frequencies, John C. Miers

Mechanical Engineering Undergraduate Honors Theses

Droplet formation has been a fascinating subject to scientists for centuries due to its natural beauty and importance to both scientific and industrial applications, such as inkjet printing, reagent deposition, and spray cooling. However, the droplet generation frequency of common drop-on-demand jetting techniques is mostly limited to ~10 kHz. This paper presents an investigation of the possibility of jetting at megahertz frequencies in order to boost the productivity of drop-on-demand material deposition by ~100 times. The focus of this paper is to understand the limitations of generating droplets at a megahertz frequency and to explore possible solutions for overcoming these …

Automatic Dependent Surveillance-Broadcast For Detect And Avoid On Small Unmanned Aircraft, Matthew Owen Duffield

Theses and Dissertations

Small unmanned aircraft systems (UAS) are rapidly gaining popularity. As the excitement surrounding small UAS has grown, the Federal Aviation Administration (FAA) has repeatedly stated that UAS must be capable of detecting and avoiding manned and unmanned aircraft. In developing detect-and-avoid (DAA) technology, one of the key challenges is identifying a suitable sensor. Automatic Dependent Surveillance-Broadcast (ADS-B) has gained much attention in both the research and consumer sectors as a promising solution. While ADS-B has many positive characteristics, further analysis is necessary to determine if it is suitable as a DAA sensor in environments with high-density small UAS operations. To …

Error Propagation Dynamics Of Piv-Based Pressure Field Calculation, Zhao Pan

Theses and Dissertations

Particle Image Velocimetry (PIV) based pressure field calculation is becoming increasingly popular in experimental fluid dynamics due to its non-intrusive nature. Errors propagated from PIV results to pressure field calculations are unavoidable, and in most cases, non-negligible. However, the specific dynamics of this error propagation process have not been unveiled. This dissertation examines both why and how errors in the experimental data are propagated to the pressure field by direct analysis of the pressure Poisson equation. Error in the pressure calculations are bounded with the error level of the experimental data. The error bounds quantitatively explain why and how many …

Thermal Conductivity Measurements Of Nanomaterials, Javier Acosta Martinez

Theses and Dissertations

Thermal conductivity “k” can be defined as a material property where heat is diffused due to a temperature gradient within the material. Among the applications for thermal conductivity are: thermoelectrics, thermal interface materials, thin films, insulation, among many others. A study was made to compare the different types of studies of thermal conductivity of nanomaterials, as well as, a comparison among the different types of setups used to measure thermal conductivity. For this study a custom made thermal conductivity tester was built, this tester was validated by measuring materials with both low and high thermal conductivity, and comparing the results …

Numerical Simulation Of Tip Clearance Impact On A Pumpjet Propulsor, Lin Lu, Guang Pan, Jing Wei, Yipeng Pan

Ocean Engineering and Marine Sciences Faculty Publications

Numerical simulation based on the Reynolds Averaged NaviereStokes (RANS) Computational Fluid Dynamics (CFD) method had been carried out with the commercial code ANSYS CFX. The structured grid and SST keu turbulence model had been adopted. The impact of noncondensable gas (NCG) on cavitation performance had been introduced into the Schnerr and Sauer cavitation model. The numerical investigation of cavitating flow of marine propeller E779A was carried out with different advance ratios and cavitation numbers to verify the numerical simulation method. Tip clearance effects on the performance of pumpjet propulsor had been investigated. Results showed that the structure and characteristics of …

Nonlinear Dynamics Of Electrostatically Actuated Nanotweezers, Bin Liu

Theses and Dissertations

Bin Liu, Nonlinear Dynamics of Electrostatically Actuated Nanotweezers. Master of Science (MS), May 2016, 77 pp, 6 tables, 59 figures, references, 25 titles. The amplitude-frequency response of electrostatic nanotube nanotweezer device system is investigated; soft alter current was setting at near half natural frequency impulse on nanotubes which are referred to as two arms, parametric and primary resonances will be shown in the results, respectively. Firstly we are using the Method of Multiple Scales (MMS) analytical model; results will be compared with Reduced Order Model (ROM). By variation and comparison of multiple parameters including van der wall molecular forces, electrostatic …

Graphene-Based Nanomaterials For Hydrogen Generation And Storage, Lin Wei

Theses and Dissertations

Hydrogen energy is promising candidate to replace fossil fuel. However, the usage of hydrogen energy was greatly limited due to its generation and storage. In this thesis report, the author synthesized novel metal/carbon nanomaterials used for the hydrogen storage and hydrogen evolution reaction. These materials were characterization by XRD, Raman, XPS, SEM, EDX, etc. And the surface area and the hydrogen storage properties were tested by ASAP 2020, using the BET measurement and hydrogen isotherm curves to discuss the gas adsorption properties. As for hydrogen evolution reaction, the materials were made into electrodes and tested with LSV, CV to shows …

Techno-Economic Assessment Of Micro-Algae Production Systems, Justin Hoffman

All Graduate Plan B and other Reports, Spring 1920 to Spring 2023

Global oil consumption is rising at an unprecedented rate renewing interest in alternative fuels. Micro-algae represents a promising feedstock due to inherent advantages such as high solar energy efficiencies, large lipid fractions, and utilization of various waste streams including industrial flue gas. Current technological challenges have limited the commercial viability of microalgae based biofuel production systems. This study directly evaluates and compares the economic viability of biomass production from two different open cultivation platforms, 1) algal turf scrubbers and 2) open raceway ponds. Modular sub-process models were developed and leveraged for the economic comparison of the systems on the metrics …

Investigating The Effect Of Carbon Nanotube Functionalization In A Polydimethylsiloxane Composite Through Use Of A Stepped Bar Apparatus, Matthew I. Ralphs

All Graduate Theses and Dissertations, Spring 1920 to Summer 2023

Thermal interface materials (TIMs) are used in transporting heat away from a circuit or electronic module. Composite materials are a popular research area for TIMs because they allow the desired properties to be joined in a composite to take advantage of the best properties from all the constituents involved. The composite selected for this study uses carbon nanotubes (CNT) as the filler and an elastomeric polymer for the matrix, specifically a multiwalled carbon nanotube (MWCNT) / polydimethylsiloxane (PDMS) composite. This study looks at chemical modification (functionalization) of the CNTin an effort to produce a better bond between the CNT and …

Neutron-Gamma Discrimination In Elpasolite Scintillator Detector, Brittany Morgan

UNLV Theses, Dissertations, Professional Papers, and Capstones

Existing nuclear stockpiles and weapons-making capabilities imperil the global community. Current nonproliferation efforts involve the research and development of newer, more efficient detection systems that can be deployed for the interdiction and monitoring of special nuclear materials (SNM). Spontaneous and induced fission events in SNM produce neutrons and gamma rays, which can be detected and analyzed, in particular, using scintillator detectors. Various electronic data acquisition systems and data analysis methods have been employed to record and characterize neutron and photon signatures. The goal of this thesis is to develop a new method of discrimination between neutrons and photons in the …

On The Scattering Of An Acoustic Plane Wave By A Soft Prolate Spheroid, Joseph Michael Borromeo

UNLV Theses, Dissertations, Professional Papers, and Capstones

This thesis solves the scattering problem in which an acoustic plane wave of propagation number K1 is scattered by a soft prolate spheroid. The interior field of the scatterer is characterized by a propagation number K2, while the field radiated by the scatterer is characterized by the propagation number K3. The three fields and their normal derivatives satisfy boundary conditions at the surface of the scatterer. These boundary conditions involve six complex parameters depending on the propagation numbers. The scattered wave also satisfies the Sommerfeld radiation condition at infinity. Through analytical methods, series representations are constructed for the interior field …

Portable High Throughput Digital Microfluidics And On-Chip Bacteria Cultures, Yiyan Li

UNLV Theses, Dissertations, Professional Papers, and Capstones

An intelligent, portable, and high throughput digital microfluidic (DMF) system is developed. Chapter 1 introduces microfluidics and DMF systems. In Chapter 2, a low-cost and high resolution capacitive-to-digital converter integrated circuit is used for droplet position detection. A field-programmable gate array FPGA is used as the integrated logic hub of the system for highly reliable and efficient control of the circuit. In this chapter a fast-fabricating PCB (printed circuit board) substrate microfluidic system is proposed. Smaller actuation threshold voltages than those previously reported are obtained. Droplets (3 µL) are actuated using 200 V, 500 Hz DC pulses. Droplet positions can …

Mechanical Properties And Microstructure Evolution Of 17-4 Ph Stainless Steel Processed By Laser-Powered Bed Fusion., Harish Irrinki

Electronic Theses and Dissertations

Laser powder bed fusion (L-PBF) is a potential manufacturing route for the production of tooling using different steel materials. However, there is a limited understanding of how the mechanical properties and microstructures of the L-PBF produced parts vary with change in powder type and process conditions. The current research studied the influence of L-PBF process parameters on mechanical properties and microstructures of 17-4PH stainless steel using gas and water-atomized powders. The results demonstrate the feasibility of using water-atomized powders as starting raw materials instead of typically used gas-atomized powders to fabricate parts in the L-PBF process at high energy densities.

Effect Of Non-Uniform Air-Side Velocity Distribution On Heat Transfer Model Predictions For Microchannel Condenser., Zachary Chapin

Electronic Theses and Dissertations

This is a study of the effects on heat transfer capacity predictions of microchannel condensers when airflow is maldistributed due to the shape of the condenser. The three shapes investigated in this study are flat, U-shape and roll. Each coil was tested in a water calorimeter and those results were compared to the model prediction. The model prediction was calculated using CoilDesigner™ modeling software with standard correlations. Using the uniform airflow assumption, the model over predicted the heat capacity measured in the calorimeter by 5-11% depending on the coil and inlet conditions. The local airflow velocity was measured using a …

The Effects Of Ball Interactions On The Dynamic Behavior Of A Ball Balancer Rotating At Speeds Above The Translational Resonant Frequency Of The System., Gregory A. Dedow

Electronic Theses and Dissertations

Many applications are inherently rotational in nature. These applications range from industrial products to consumer products. As seen in a traditional frequency response plot, the motion of a rotating imbalance does not approach zero as the forcing frequency is increased. Unlike a traditional forced mass spring oscillator, the motion of the rotating imbalance approaches some non-zero value. To account for this residual motion, some systems utilize a balancing device to reduce this motion. These balancing devices can be passive or active, depending on the design considerations. This paper will focus on the traditional, passive ball-type balancer due to its simplicity …

Computing Research In Academia: Classifications, Keywords, Perceptions, And Connections, Sung Han Kim

Theses and Dissertations

The Association for Computing Machinery (ACM) recognizes five computing disciplines: Computer Science (CS), Computer Engineering (CE), Information Technology (IT), Information Systems (IS), and Software Engineering (SE). Founded in 1947 the ACM is the world's largest society for computing educators, researchers, and professionals. While Computer Science has been a degree program since 1962, the other four are relatively new. This research focuses on understanding the graduate research in four of the five ACM disciplines (CS, CE, IT, and IS) using a large body of thesis and dissertation metadata. SE is not found in the metadata and graduate work in SE is …

Xhab Microgravity Food Growth Chamber, Nathan I. Stacey

Undergraduate Honors Capstone Projects

NASA and other organizations are preparing to send humans deeper into space, including a NASA manned mission to Mars in the 2030s, in order to learn more about our universe and the origin of life and to ensure the survival of the human race. Long journeys in space require efficient, dependable, and sustainable methods to provide for astronauts' metabolic needs such as oxygen, water, and food. In order for microgravity plant growth chambers to become a viable solution, several challenges encountered by past growth chambers must be resolved.

One problem with existing space food growth chambers is hypoxia, or lack …

Pedicle Lengthening Spacer, David S. Wood

Undergraduate Honors Capstone Projects

In the lumbar region of the spine, the spinal cord travels through a small hole in your vertebrae called the spinal canal. There is a medical condition where the spinal canal becomes restricted. This condition is called stenosis. There are several reasons for this pinching of the spinal column. These include the growth of bone spurs, the accumulation of ligaments in the canal, or a genetic trait. When these occur in the lower five vertebrae (the lumbar region), it is called lumbar stenosis. The symptoms of Lumbar Stenosis are shooting pain through the legs, especially during activity, and feelings of …

Real-Time Optimization Based Power Flow Controller For Energy Consumption And Emissions Reduction In A Parallel Hev, Abdulla Abdulaziz Karmustaji

Doctoral Dissertations and Master's Theses

As the regulations on the fuel economy and emissions standards become higher, Hybrid Electric Vehicles (HEV) are gaining more popularity in the market. HEVs improvements in fuel economy and emissions strongly depend on the energy management strategy. An optimization based power flow controller is presented in this thesis to find the appropriate power split between the Internal Combustion Engine (ICE) and the electric motor to reduce the energy consumption and emissions. However, emissions were not taken into consideration in results due to lack of reliable results. A basic power flow controller was built to compare to the optimization based controller. …

Modified Trajectory Shaping Guidance For Autonomous Path Following Control Of Platooning Ground Vehicles, Ishmaal T. Erekson

All Graduate Theses and Dissertations, Spring 1920 to Summer 2023

This thesis proposes a modification of trajectory shaping guidance to provide more accurate path convergence in curved paths. The object of this thesis is to apply this simple guidance law to platooning control to ensure all vehicles in the platoon converge to a desired constant radius path at a desired vehicle separation distance. To show the viability of this new guidance law, it is shown mathematically to be exponentially stable. It is also confirmed through simulations and on ground robots.

Mild Traumatic Brain Injury: Combined In Silico And In Vitro Studies, Yi Hua

Department of Mechanical and Materials Engineering: Dissertations, Theses, and Student Research

Mild traumatic brain injury (TBI) is a significant public health concern worldwide and has attracted significant attention due to high-impact sport as well as improvised explosive devices used in military conflicts. The earliest sign of mild TBI is associated with cognitive, behavioral and physical/somatic changes, which are commonly invisible to existing medical techniques. Thus it is essential to target mechanisms of mild TBI and its associated damage measures for earlier diagnosis/treatment and enhanced protection strategies.

In this work, the mechanism of blast-induced mild TBI was inspected through integrated in silico and in vitro models. A three-dimensional (3D) human head model …

Understanding Pyrotechnic Shock Dynamics And Response Attenuation Over Distance, Richard J. Ott

All Graduate Theses and Dissertations, Spring 1920 to Summer 2023

Component requirements govern design and production in the aerospace industry. One such potential requirement for a component is the survival and continued function upon exposure to shock environments. A shock event is a high amplitude, short duration traveling wave that induces large loads on components in its path that can cause degradation of electronic components, cracks and fractures in brittle materials, local plastic deformation, and materials to experience accelerated fatigue life. In defining these environments for new structures, industry experts rely mainly on empirical data. Measurements from similar structures are scaled and enveloped to create a predicted bounding case. This …

A Method To Enhance The Heat Transfer Mechanism In Metal Particle Porous Beds With Applicability To Paramagnetic Materials For Hydrogen Storage, Shahin Shafiee

Theses and Dissertations

This research introduces a heat transfer enhancement method for porous beds of either ferromagnetic and paramagnetic materials. Throughout this work, it is shown that applying magnetic fields, not only enhances the heat transfer rate in particle beds but also improves hydrogenation properties of lanthanum nickel. The first section of the work is focused on heat transfer in iron oxide beds under magnetism. This stage studies effect of different magnetic field configurations and intensities on conduction improvement. The second phase of the work, studies the effect of utilizing magnetic fields on hydriding properties of a selected metal hydride. Experimentation has proven …

Investigating The Effect Of Capping Layers On Final Thin Film Morphology After A Dewetting Process, Benjamin C. White

All Graduate Theses and Dissertations, Spring 1920 to Summer 2023

Nanoparticles on a substrate have numerous applications in nanotechnology, from enhancements to solar cell efficiency to improvements in carbon nanotube growth. Producing nanoparticles in a cheap fashion with some control over size and spacing is difficult to do, but desired. This work presents a novel method for altering the size and spacing of nickel and gold nanoparticles. Dewetting is a methodology to reduce thin films to an ensemble of discrete droplets. The introduction of alumina capping layers to thin nickel films during a pulsed laser-induced dewetting process has yielded reductions in the mean and standard deviation of radii and pitch …

Path Following By A Quadrotor Using Virtual Target Pursuit Guidance, Abhishek Manjunath

All Graduate Theses and Dissertations, Spring 1920 to Summer 2023

Missile guidance laws have been solely developed to follow and intercept a target thereby destroying or damaging it. In this research, the primary objective is to modify and adopt a missile guidance law to be used on a quadrotor to follow a virtual target. The target is termed 'virtual' as it only exists mathematically in the form of equations. The goal is to have the quadrotor successfully following the predefined path (described by the target) while maintaining a fixed distance from the virtual target. To ensure viability and assess performance, a detailed comparison with another path following law is made.

Impact Of Heavy Metal Contamination From Coal Flue Gas On Microalgae Biofuel And Biogas Production Through Multiple Conversion Pathways, Derek E. Hess

All Graduate Theses and Dissertations, Spring 1920 to Summer 2023

Microalgae has a great potential to help alleviate the world's current dependence on fossil fuels. Microalgae is a single celled organism that produces lipids as a food storage device much like humans and animals store fat. These lipids are a kind of oil that when harvested can be utilized as biofuel.

As the technology surrounding using microalgae as a source of biofuel has advanced key bottlenecks in the eventual large-scale production of microalgae based biofuel have been discovered. One of these bottlenecks is the need to cheaply supply carbon for microalgae growth. One idea that has emerged as a plausible …

Quadrotor Uav Path Following Using Trajectory Shaping, Parwinder Singh Mehrok

All Graduate Theses and Dissertations, Spring 1920 to Summer 2023

The propose of this research is to develop a path following control law known as Trajectory Shaping. The approach is to develop a three- dimensional (3D) version of it from an existing two-dimensional (2D) model. Apart from research on this 3D control law, a multirotor unmanned aerial vehicle (UAV) platform, having four rotors and known as quadrotor is designed from the ground up for validating the concept of path following. Several pre-defined paths like the circle and figure-eight trajectories are used to apply the newly developed version of this control law. The existing 2D concept of Trajectory Shaping guidance …

Throttleable Gox/Abs Launch Assist Hybrid Rocket Motor For Small Scale Air Launch Platform, Zachary S. Spurrier

All Graduate Theses and Dissertations, Spring 1920 to Summer 2023

The ability for an aircraft-based launch platform to place an orbital payload onto a nominal launch trajectory at a higher energy state -- altitude, velocity, flight path angle, and azimuth --using highly-efficient air breathing propulsion instead of a much lower-efficiency rocket system, offers the potential for a significantly smaller launch vehicle. An airborne platform also provides the ability to launch from multiple locations and allows for significantly increased "system responsiveness." The NASA Armstrong Flight Research Center’s Towed Glider Air-Launch System (TGALS) is a small-scale flight research project investigating the feasibility for a remotely-piloted, towed, glider system to act as a …