Mechanical Engineering Commons^™

In Vitro Assessment Of Laser Sintered Bioactive Glass Scaffolds With Different Pore Geometries, Krishna C. R. Kolan, Albin Thomas, Ming-Chuan Leu, Greg Hilmas

Mechanical and Aerospace Engineering Faculty Research & Creative Works

The pore geometry of bioactive glass scaffolds intended for use in bone repair or replacement is one of the most important parameters that could determine the rate of bone regeneration. The pore geometry would also affect the mechanical properties of the scaffolds and their rate of degradation. Scaffolds with five different architectures, having ~50% porosity, were fabricated with silicate (13–93) and borate (13–93B3) based bioactive glasses using a laser sintering process. An established, late-osteoblasts/early-osteocytes cell line was used to perform cell proliferation tests on the scaffolds. The results indicated that the cells proliferate significantly more on the scaffolds which mimic …

Mechanical Engineering News, Georgia Southern University

Mechanical Engineering: News & Publications (2013-2023)

• Georgia Southern hosts prestigious National Science Foundation Research Experience for Undergraduates (REU) in Green- Engineered Transportation Technologies

Adjustable Resonance Frequency Of Rf-Mems Capacitor By Using Comb- Drive Actuators: A Design Approaches, Agus Santoso Tamsir, Sandy Tannu Wijaya, Dato’ Burhanuddin Yeop Majlis

Makara Journal of Technology

The needs of smaller size RF varactor is a must today, and MEMS comes to be the potential one. In this paper we proposed an adjustable resonance RF-MEMS varactor by using comb-drive actuators placing in each side of the square movable plate. In our preliminary simulation, we found that the device can work properly but some constraints comes such as the dominancies of harmonic resonance frequencies that influences into the nominal capacitances. Therefore for the next step of development we have to find out the window of the structural dimension for a certain spans and a certain operating frequencies.

Make Or Buy Analysis Model Based On Tolerance Design To Minimize Manufacturing Cost And Quality Loss, Cucuk Nur Rosyidi, Reza Rizkichani Akbar, Wakhid Ahmad Jauhari

Makara Journal of Technology

In a manufacturing company, manufacturing costs, or component prices, and tolerance will affect the price and the quality of a product. Companies must produce high-quality products with low manufacturing costs in order to keep their products competitive in the market; however, it is difficult to produce a high-quality product with a low manufacturing cost. Companies have difficulties in determining the components to be produced using their own manufacturing facilities (make) or outsourced to their suppliers (buy). Hence, a make or buy analysis is needed to minimize the manufacturing costs and quality loss and to determine the optimum alternative regarding make …

Observation Of Tunneling Effects In Lateral Nanowire Pn Junctions, Sri Purwiyanti, Arief Udhiarto, Daniel Moraru, Takeshi Mizuno, Djoko Hartanto, Michiharu Tabe

Makara Journal of Technology

As electronic device dimensions are continuously reduced, applied bias conditions significantly change and the transport mechanisms must be reconsidered. Tunneling devices are promising for scaled-down electronics because of expected high-speed operation and relatively low bias. In this work, we investigated the tunneling features in silicon-oninsulator lateral nanowire pn junction and pin junction devices. By controlling the substrate voltage, tunneling features can be observed in the electrical characteristics. We found that the minimum substrate voltage required for tunneling to occur in pn junctions is higher as compared with pin junctions. The main cause of these effects relies in the difference between …

Argon Ion Irradiation Effect On The Magnetic Properties Of Fe-Al2o3 Nano Granular Film, Setyo Purwanto, Isao Sakamoto

Makara Journal of Technology

We studied the effect of Argon (Ar) ion irradiation on Fe-Al2O3 nanogranular thin film. X-ray diffraction (XRD) patterns show that the ion dose might promote the growth of the Fe2O3 phase from an amorphous phase to a crystalline phase. The magnetic and magnetoresistance properties were investigated using a vibrating sample magnetometer (VSM) and a four point probe (FPP). The results suggest that percolation concentration occurred at the 0.55 Fe volume fraction and with a maximum magnetoresistance (MR) ratio of 3%. The present MR ratio was lower than that of previous results, which might be related to the existence of the …

Digestibility Of Betung Bamboo Fiber Following Fungal Pretreatment, Widya Fatriasari, Wasrin Syafii, Nyoman J. Wistara, Khaswar Syamsu, Bambang Prasetya

Makara Journal of Technology

This research evaluated the effect of fungal pretreatment of betung bamboo fibers and enzymatic- and microwaveassisted hydrolysis on the reducing sugar yield. The enzymatic hydrolysis of the pretreated biomass was carried out with cellulase and 10 and 20 FPU/g of substrate in a shaking incubator at 50 °C and 150 rpm for 48 h. The sulfuric acid concentration used in the microwave-assisted acid hydrolysis was 1.0, 2.5, and 5%, either with or without the addition of activated carbon. Microwave irradiation (330 Watt) was applied for 5–12.5 min. The yield of reducing sugar was better with the microwave-assisted acid hydrolysis, and …

Electron Emission Characteristics Of Multi-Gated Field Emitters, Hidenori Mimura, Yoichiro Neo, Toru Aoki, Tomoya Yoshida, Masayoshi Nagao

Makara Journal of Technology

We have developed a multi-gated field emitter (FE) such as a quadruple-gated FE with a three-stacked electrode lens and a quintuple-gated FE with a four-stacked electrode lens. Both the FEs can focus the electron beam. However, the quintuple-gated FE has a stronger electron convergence than the quadruple-gated FE, and a beam crossover is clearly observed for the quintuple-gated FE.

Properties Of Lignin From Oil Palm Empty Fruit Bunch And Its Application For Plywood Adhesive, Lucky Risanto, Euis Hermiati, Yanni Sudiyani

Makara Journal of Technology

Lignin from lignocellulosic biomass is a potential biopolymer for wood adhesive. The aims of this study were to characterize lignin isolated from the black liquor of oil palm empty fruit bunch fiber pretreated with steam explosion in alkaline conditions and to examine the bond quality of aqueous polymer isocyanate (API) adhesive prepared from lignin, natural rubber latex (NRL), and polyvinyl alcohol (PVA) as base polymers with isocyanate crosslinkers. Lignin was precipitated from the black liquor by adding hydrochloric acid; then the precipitate was separated by filtration, thoroughly washed with water up to pH 2 and pH 5, and dried. The …

The Gaussian Orthogonal Laplacianfaces Modelling In Feature Space For Facial Image Recognition, Arif Muntasa

Makara Journal of Technology

Dimensionality reduction based on appearance has been interesting issue on the face image research fields. Eigenface and Fisherface are linear techniques based on full spectral features, for both Eigenface and Fisherface produce global manifold structure. Inability of them in yielding local manifold structure have been solved by Laplacianfaces and further improved by Orthogonal Laplacianfaces, so it can yield orthogonal feature vectors. However, they have also a weakness, when training set samples have non-linear distribution. To overcome this weakness, feature extraction through data mapping from input to feature space using Gaussian kernel function is proposed. To avoid singularity, the Eigenface decomposition …

Series-Interconnected Plastic Dye-Sensitized Solar Cells Prepared By Low- Temperature Binder-Free Titania Paste, Erlyta Septa Rosa, Lia Muliani, Shobih Shobih, Jojo Hidayat, Brian Yuliarto

Makara Journal of Technology

The aim of this research is to study dye-sensitized solar cells (DSSC). This was implemented on a flexible polyethylene terephthalate (PET) substrate using a mixture of transparent and scattered mesoporous anatase-titania as the electron transport layer for the photoelectrode. This mixture of anatase titania performed a dual function of light scattering and efficient dye absorption. In this study, a porous nano-TiO2 film was prepared on indium tin oxide (ITO) coated polyethylene terephthalate (PET) by using a binder-free titania paste; on it, a DSSC was fabricated. The paste which contained a mixture of TiO2 nanoparticles, acid chloride, and ethanol was printed …

An Assessment Of Acoustic Contrast Between Long And Short Vowels Using Convex Hulls, Erin F. Haynes, Michael Taylor

Mechanical Engineering

An alternative to the spectral overlap assessment metric (SOAM), first introduced by Wassink [(2006). J. Acoust. Soc. Am. 119(4), 2334–2350], is introduced. The SOAM quantifies the intra- and inter-language differences between long–short vowel pairs through a comparison of spectral (F1, F2) and temporal properties modeled with best fit ellipses (F1 × F2 space) and ellipsoids (F1 × F2 × duration). However, the SOAM ellipses and ellipsoids rely on a Gaussian distribution of vowel data and a dense dataset, neither of which can be assumed in endangered languages or languages with limited available data. The method presented in this paper, called …

Foss Big Data Storage Solution, Nurdeen Salami

STAR Program Research Presentations

NASA projects require a reliable approach to store large volumes of data. Accordingly, it is crucial to adopt a lightweight, reliable, and scalable database. Current NASA databases bear costly license fees with undesirable speed and flexibility. The purpose of utilizing the AERO Institute as an IT test bed, or “Sandbox,” is to design, build, test, and implement software solutions prior to transfer to NASA projects. Cassandra coupled with the Astyanax API is a viable solution for storing big data. Store a minimum of 2GB of C-FOSS data in multiple file formats (.csv, .log, .xml, and .jpg). Use benchmark tests to …

Space Race: Capturing An Orbiting Sample And A Nation’S Imagination, Stephanie La Liberte, Andrew Chavarin, Shubham Gogna, C. Daniel Thomas, Vy Phung, Gabriel Udomkesmalee

STAR Program Research Presentations

A proposed architecture for future planetary sample return missions would consist of capturing on-orbit a sample container (collected from the surface of a planetary body and launched into space) and transferring the sample container into an earth return/reentry capsule. A challenge to this proposed architecture is integrating space applicable sensor technologies with sufficient capturing devices. While useful technologies on Earth, Earth-related rendezvous/capture technologies, such as magnetic field sensors, sound-based sensors, and Earth orbit-based radios like GPS, are not applicable to space. Inspired by the in-orbit sample capture challenge, NASA JPL has designed the Space Rendezvous And Capture Experiment (Space RACE). …

Atomistic Simulation And Virtual Diffraction Characterization Of Alumina Interfaces: Evaluating Structure And Stability For Predictive Physical Vapor Deposition Models, Shawn Patrick Coleman

Graduate Theses and Dissertations

The objectives of this work are to investigate the structure and energetic stability of different alumina (Al₂O₃) phases using atomistic simulation and virtual diffraction characterization. To meet these objectives, this research performs molecular statics and molecular dynamics simulations employing the reactive force-field (ReaxFF) potential to model bulk, interface, and surface structures in the θ-, γ-, κ-, and α-Al₂O₃ system. Simulations throughout this study are characterized using a new virtual diffraction algorithm, developed and implemented for this work, that creates both selected area electron diffraction (SAED) and x-ray diffraction (XRD) line profiles without assuming …

Development Of An In Vitro System For Evaluation Of Prosthetic Vein Valves, Ross Gorman

All Theses

Chronic venous insufficiency is a chronic disorder where venous pressure is not reduced during exercise. In a healthy individual, the vein valves and muscle pumps of the extremities combine to allow for a reduction in venous pressure during exercise. Consistent high pressure in the leg can lead to disability, pain, and ulcer formation. Typical causes of chronic venous insufficiency are venous reflux and acute venous obstruction. Research is under way to develop a prosthetic vein valve that can easily be implanted with a minimally invasive catheter procedure which addresses chronic venous insufficiency. This thesis discusses development of an in vitro …

Cost Effectiveness Of 2015 Iecc Compliance Using The Hers Index, Florida Solar Energy Center, Philip W. Fairey

FSEC Energy Research Center®

The EnergyGauge HERS software tool is used to examine the 2012 IECC Standard Reference Design (IECC SRD) configuration for three-bedroom, one-story 2000 ft² and three-bedroom, two-story 2,400 ft² single-family homes in sixteen representative U.S. cities. The energy use of the 2012 SRD homes is compared against the energy use of homes complying with the 2015 IECC using the ERI compliance method. HERS simulations for each home are conducted for both a best case home orientation and a worst case home orientation. Improvements to the 2012 IECC SRD homes are made such that the HERS Index for the homes …

Electrokinetic Instabilities In Ferrofluid Microflows, Dhileep Thanjavur Kumar

All Theses

Lab-on-a-chip devices have been increasingly used in the past two decades for chemical and biomedical analysis. These devices employ the concepts of microfluidics and offer the promise of incorporating multiple laboratory processes onto a single portable chip. Electric field has been often employed in microfluidic devices for the ease of fluid and sample control as well as the convenience of chip integration and interfacing. Flow instabilities can take place when two fluids of unequal electrical properties are pumped through a microchannel under the application of an adequately strong electric field. The study of these electrokinetic instabilities in microfluidic devices is …

Fatigue-Induced Failure In Horizontal-Axis Wind-Turbine (Hawt) Blades And Hawt Drivetrain Gears, Varun Chenna

All Theses

Wind energy is one of the most promising and the fastest growing installed alternative-energy production technologies. In fact, it is anticipated that by 2030, at least 20% of the U.S. energy needs will be met by various onshore and offshore wind-farms [a collection of wind-turbines (converters of wind energy into electrical energy) at the same location]. A majority of wind turbines nowadays fall into the class of the so-called Horizontal Axis Wind Turbines (HAWTs). Turbine blades and the gearbox are perhaps the most critical components/subsystems in the present designs of HAWTs. The combination of high failure rates (particularly those associated …

Effects Of Local Ph On The Formation And Regulation Of Cristae Morphologies, Dong Hoon Song, Jonghyun Park, Martin A. Philbert, Ann Marie Sastry, Wei Lu

Mechanical and Aerospace Engineering Faculty Research & Creative Works

Cristae, folded subcompartments of the inner mitochondrial membrane (IMM), have complex and dynamic morphologies. Since cristae are the major site of adenosine triphosphate synthesis, morphological changes of cristae have been studied in relation to functional states of mitochondria. In this sense, investigating the functional and structural significance of cristae may be critical for understanding progressive mitochondrial dysfunction. However, the detailed mechanisms of the formation and regulation of these cristae structures have not been fully elucidated. Among the hypotheses concerning the regulation of cristae morphologies, we exclusively investigate the effects of the local pH gradient on the cristae morphologies by using …

A Verification Of Steady State Discontinuous Solutions Using The Method Of Manufactured Solutions For Finite Volume Computational Fluid Dynamic Codes, Benjamin Grier

All Dissertations

When applying the method of manufactured solutions (MMS) on computational fluid dynamic (CFD) software, it is traditionally a requirement that all solutions be continuous on the computational domain. This stipulation is limiting for the verification and validation of CFD solutions where discontinuities are frequent. This work details the development of a discontinuous MMS method for finite volume codes. The CFD code used throughout this research is a cell centered, finite volume, 1st order, Eulerian scheme within the software AVUS (Air Vehicles Unstructured Solver) which is combined with uniform structured grids. This code is used as a representative testing platform with …

Effects Of Relaxed Assumptions On The State Switching Technique, Stephen Ilardi

HIM 1990-2015

This thesis explores the effects of two assumptions commonly used in mathematical models related to a piezoelectric damping method known as State Switching. The technique relies on changing the stiffness state of a piezoelectric patch through control of the electrical boundary conditions. The transition between stiffness states is assumed to occur instantaneously and in concurrence with the switch event. In actuality, the transition will occur over a finite time and will trail behind the switch event by a finite time. For these assumptions to be valid, the effects of switch duration and delay on the performance of the State Switching …

Modeling Financial Markets Using Concepts From Mechanical Vibrations And Mass-Spring Systems, Michael Gandia

HIM 1990-2015

This thesis describes a method of modeling financial markets by utilizing concepts from mechanical vibration. The models developed represent multi-degree of freedom, mass-spring systems. The economic principles that drive the design are supply and demand, which act as springs, and shareholders, which act as masses. The primary assumption of this research is that events cannot be predicted but the responses to those events can be. In other words, economic stimuli create responses to a stock’s price that is predictable, repeatable and scientific. The approach to determining the behavior of various financial markets encompassed techniques such as Fast Fourier Transform and …

Development And Applications Of The Expanded Equivalent Fluid Method, Bharath Kumar Kandula

Dissertations

Ocean acoustics is the study of sound in the oceans. Electromagnetic waves attenuate rapidly in the water medium. Sound is the best means to transmit information underwater. Computational numerical simulations play an important role in ocean acoustics. Simulations of acoustic propagation in the oceans are challenging due to the complexities involved in the ocean environment. Different methods have been developed to simulate underwater sound propagation. The Parabolic-Equation (PE) method is the best choice in several ocean acoustic problems. In shallow water acoustic experiments, sound loses some of its energy when it interacts with the bottom. An equivalent fluid technique was …

Conflict Management And Model Consistency In Multi-User Cad, Ammon Ikaika Hepworth

Theses and Dissertations

The NSF Center for e-Design, Brigham Young University (BYU) site has re-architected Computer Aided Design (CAD) tools, enabling multiple users to concurrently create, modify and view the same CAD part or assembly. This technology allows engineers, designers and manufacturing personnel to simultaneously contribute to the design of a part or assembly in real time,enabling parallel work environments within the CAD system. Multi-user systems are only as robust and efficient as their methods for managing conflicts and preserving model consistency. Conflicts occur in multi-user CAD when multiple users interoperate with the same or dependent geometry. Some conflicts can lead to model …

Electroencephalography(Eeg) Data Collection And Processing Through Machine Learning, Jayshree Desai

Graduate Theses and Dissertations

Machine learning methods are an excellent way for understanding the neural basis of human decision making. Some machine learning systems try to eradicate the need for human intuition in data analysis whereas others embrace a collective approach between humans and machines. The objective of this project is to collect Electroencephalography (EEG) signals through wireless sensors, and the process the collected signals through machine learning methods. The EEG data is collected using three EEG electrodes, each being the positive, negative and ground terminals respectively. Since the signal measures in the unit of micro-volts it needs to be amplified using amplifier circuit. …

Theoretical And Computational Design Analysis Of A Harmonica Type Aeroelastic Energy Harvester, Songkai Wang

All Theses

A wind energy harvester inspired by music playing harmonicas was proposed for micro-power generation. The energy harvester utilizes flow-excited self-sustained oscillations of a piezoelectric cantilever beam mounted in a wind pipe to generate electric power. The dependence of the energy harvester's power generation performance on a set of the design parameters such as the chamber volume, aperture width and beam dimensions has been studied previously. However, the performance of the nonlinear multi-physics system with two-way fluid structure coupling also depends on other design parameters such as the geometry of the oscillatory beam, the beam mounting configuration and the geometry of …

Analytical And Experimental Analysis Of Magnetorheological Elastomers, Sarah Trabia

UNLV Theses, Dissertations, Professional Papers, and Capstones

Many engineering applications ranging from robotic joints to shock and vibration mitigation can benefit by incorporating components with variable stiffness. In addition, variable stiffness structures can provide haptic feedback (the sense of touch) to the user. In this work, it is proposed to study Magnetorheological Elastomers (MRE), where iron particles within the elastomer compound develop a dipole interaction energy, to be used in a device for haptic feedback. A novel feature of this MRE device is to introduce a field-induced variable shear modulus bias via a permanent magnet and using a current input to the electromagnetic control coil to change …

Neutron Spectroscopy With Scintillation Detectors Using Wavelets, Jessica Hartman

UNLV Theses, Dissertations, Professional Papers, and Capstones

The purpose of this research was to study neutron spectroscopy using the EJ-299-33A plastic scintillator. This scintillator material provided a novel means of detection for fast neutrons, without the disadvantages of traditional liquid scintillation materials. EJ-299-33A provided a more durable option to these materials, making it less likely to be damaged during handling. Unlike liquid scintillators, this plastic scintillator was manufactured from a non-toxic material, making it safer to use, as well as easier to design detectors. The material was also manufactured with inherent pulse shape discrimination abilities, making it suitable for use in neutron detection.

The neutron spectral unfolding …

Feedback Speed Control Of A Small Two-Stroke Internal Combustion Engine That Propels An Unmanned Aerial Vehicle, Paul D. Fjare

UNLV Theses, Dissertations, Professional Papers, and Capstones

Unmanned aerial vehicles (UAV) require intelligent control of their power source. Small UAV are typically powered by electric motors or small two-stroke internal combustion (IC) engines. Small IC engines allow for longer flight times but are more difficult to control and cause significant ground noise. A hybrid operation that uses the engine at high altitudes and the electric motors at low altitudes is desired. This would allow for extended flight with acceptable ground noise levels. Since the engine can not be restarted in the air it must be able to remain at idle for an extended time without stalling. A …