Mechanical Engineering Commons^™

Thermal Models Of Railroad Wheels And Bearings, Kevin D. Cole, Constantine M. Tarawneh, Arturo A. Fuentes, B. M. Wilson, L. Navarro

Department of Mechanical and Materials Engineering: Faculty Publications

The rolling surface for railroad wheels can be a heat source that may have an impact on the performance of the wheel bearing. In this study, experimental data from an electrically-heated railroad wheel set is analyzed by constructing thermal models of the wheel set. A steady finite-element model, a steady-analytical model, and a transient lumped-parameter model are discussed. Model parameters are determined from careful comparisons with the experimental data. The lumped-parameter model given here is intended as a simple predictive tool for determining when wheel heating caused by rail operations will have an impact on bearing temperature. The model parameters …

Engineering Sport Safety: A Study Of Equestrian Cross Country Eventing, Katherine M. Kahmann

University of Kentucky Master's Theses

The sport of equestrian cross country eventing has seen many serious and even fatal injuries due to rotational horse falls in recent years. The sport originally consisted of horse and rider teams jumping stationary, wood fences. However, in a move towards increasing safety for horses and riders, frangible and deformable safety devices have been emerging in the field. This thesis provides an overview of safety designs that are currently available and those that are on the horizon. Also, a path-finder method of evaluating and developing safety fence designs was outlined and applied to two distinct designs, a hinged gate and …

Characterization Of Defects In Metal Sheets Via Infrared Thermography, Marc Anthony Harik

University of Kentucky Master's Theses

Defects in Aluminum, Stainless steel and galvanized steel sheets are studied in reflection mode infrared thermography. The effect of material properties, surface finish, heating intensity, heater emission spectra, pixel size and defect size are studied. Contrast is governed by heat quality, emissivity and defect geometry—which follows a logarithmic trend. The diameter detected via infrared thermography is found to be at least 30% larger than the measured diameter and sub-pixel defects can be detected. The use of gradient and Laplacian of temperature is introduced as a means of increasing defect contrast and mitigating heater variation.

Transitional Flow Prediction Of A Compressor Airfoil, Vivek Hariharan

University of Kentucky Master's Theses

The steady flow aerodynamics of a cascade of compressor airfoils is computed using a two-dimensional thin layer Navier-Stokes flow solver. The Dhawan and Narasimha transition model and Mayle‟s transition length model were implemented in this flow solver so that transition from laminar to turbulent flow could be included in the computations. A method to speed up the convergence of the fully turbulent calculations has been introduced. In addition, the effect of turbulence production formulations and including streamline curvature correction in the Spalart-Allmaras turbulence model on the transition calculations is studied. These transitional calculations are correlated with the low and high …

Numerical Modeling Of The Dynamic Response Of A Multi-Bilinear-Spring Support System, Trey D. Gilliam

University of Kentucky Master's Theses

The Alpha Magnetic Spectrometer is an International Space Station Experiment that features a unique nonlinear support system with no previous flight heritage. The experiment consists of multiple straps with piecewise-linear stiffness curves that support a cryogenic magnet in three-dimensional space inside of a vacuum chamber. The stiffness curves for each strap are essentially bilinear and switch between two distinct slopes at a specified displacement. This highly nonlinear support system poses many questions in regards to feasible computational methods of analysis and possible response behavior. This thesis develops a numerical model for a multi-bilinear-spring support system motivated by the Alpha Magnetic …

Investigation And Modeling Of Ice Fracture In Cold Ocean Engineering Applications, Rocky S. Taylor

Link Foundation Ocean Engineering and Instrumentation Fellowship Reports

Ice conditions present a significant challenge in the design of ships and structures for the development of offshore energy resources in cold ocean environments. Many regions throughout the world including Alaska, Canada, Russia, Norway, Kazakhstan and China are developing offshore energy resources in ice-prone environments. The growth and stability of the global economy is closely linked to that of our energy supply, and offshore industrial activity in Northern regions has increased significantly in recent years. One of the most significant engineering challenges when designing structures for ice environments is the estimation of design ice loads. The design load scenario for …

Molecular Simulation Of The Infrared Absorption Cross Section And Thermophysical Properties Of A Polyatomic Fluid, Zhi Liang

Doctoral Dissertations

"The work presented in this dissertation aims at ab initio calculations of the infrared absorption cross section, heat capacity, self-diffusion coefficient, shear viscosity and thermal conductivity of a polyatomic fluid with the aid of statistical mechanics. The simulation is firstly focused on calculating single-molecule properties such as molecular structure, vibrational energy eigen values and transition dipole moments using an efficient method based on the density functional theory. Based on these ab initio results, the infrared absorption cross sections are determined by the Fermi's Golden rule, and the thermophysical properties are determined from molecular dynamics simulations. Using carbon dioxide as an …

Freeze Extrusion Fabrication Of 13-93 Bioactive Glass Scaffolds For Bone Repair, Nikhil D. Doiphode

Masters Theses

"We have investigated Freeze Extrusion Fabrication (FEF) of 13-93 bioactive glass to fabricate three dimensional scaffolds for bone tissue engineering. Bioactive glass paste was prepared for consistent extrusion through micro-nozzle and controlled porosity scaffolds were fabricated using additive manufacturing FEF. CAD models were prepared for different scaffold designs and computer controlled layer-by-layer deposition of pseudoplastic paste was carried out to in accordance. Liquid nitrogen assisted freezing of pastes was used for the consolidation of deposited layers. Post processing binder burnout and sintering schedules were designed for evaporation of organic binder and densification of glass. Sintering shrinkage was measured, and X-ray …

Performance Evaluation Of A Novel Diesel Fuel Air Separation And Filtration System For An Indirect Injection Diesel Engine, Michael Ray Hess

Masters Theses

"The objective of this research was to evaluate an air/fuel separation system known as a Fuel Preporator. The device's efficacy was determined by studying the effect of air entrainment on engine performance and fuel consumption of a General Motors 6.5 L naturally aspirated indirect injection (IDI) diesel engine. A test bed was developed to accommodate the test engine and test methods were adapted from federal regulations for steady-state engine testing (40 CFR 89 Subpart E). Cases of 0%, 5%, 10%, and 20% volumetric air entrainment were investigated for engine operation with and without the Fuel Preporator. Key measured engine performance …

Design And Critical Performance Evaluation Of Horizontal Axis Hydrokinetic Turbines, Suchi Subhra Mukherji

Masters Theses

"The current work discusses the hydrodynamic performance of horizontal axis hydrokinetic turbines (HAHkT) under different turbine geometries and flow conditions. Hydrokinetic turbines are a class of zero-head hydropower systems which utilize kinetic energy of flowing water to drive a generator. However, such turbines often suffer from low-efficiency. A detailed computational fluid dynamics study was performed using a low-order k-[omega] SST (Shear Stress Transport) turbulence model to examine the effect of each of tip-speed ratio, solidity, angle of attack and number of blades on the performance of small HAHkTs with a power capacity of 10 kW. The numerical models (both two-dimensional …

Integration And Characterization Of An Electrical Storage System For A Hydrogen Fuel Cell Plug-In Hybrid Electric Vehicle, Edward Alexei Anculle Arauco

Masters Theses

"Hydrogen fuel cell hybrid vehicles are an advance technology that promises to solve the energy crisis in transportation and green houses emissions. Even more, Plug-in or extended range vehicles can add diversity in energy sources. Extended range vehicles have the capability to extract energy from the grid and hence reduce the cost of operation of the vehicle. EcoCAR: the NeXt Challenge is a Noth [sic] American competition with seventeen schools participating across North America. Missouri S&T is developing a Fuel Cell Plug-in Hybrid electric vehicle which has a large lithium-ion battery able to store 16 kWh. The fuel cell powertrain …

Scaffold Based In-Vitro Osteodistraction For Bone Tissue Engineering, Cesar Adrian Terrazas

Open Access Theses & Dissertations

Engineering of hard tissues such as bone is a challenge because of the limited ability of the body to heal large defects. Current treatment options, such as employing bone sections from the patient or a deceased donor have been utilized for some time now with various degrees of success. However, these methods still exhibit many limitations such as limited supply and the possibility of transmission of disease.

To address the many limitations of bone grafts, synthetic engineered substitutes have been developed and widely researched for nearly three decades. Generally termed scaffolds, these are matrices that serve the purpose of temporary …

An Investigation On Pulsing Performance Of Mn Class Bi-Propellant Thrusters, Carlos Francisco Gomez

Open Access Theses & Dissertations

With the advancement of technology and machining methods, considerable attention has been focused in manufacturing micro thrusters for micro spacecraft applications (Yetter et al, 2003). Micro propulsion systems are currently being investigated for Miniature Kill Vehicles (MKV) and Micro Satellite Systems (MSS) with an emphasis in reducing weight and cost but without affecting performance. Reducing the weight seems practical when reducing the size of the propulsion system, but problems are encountered with system design.

In addition, propulsion requirements strongly influence choice in propellant and complexity. A thorough understanding of stabilizing thrust levels and the ability to control the propulsion system …

A Variational Approach To Non-Newtonian Flow In Angular Pores: An Application To Enchanced Oil Recovery, Nithin Kavoori

Open Access Theses & Dissertations

With an alarming rise in carbon dioxide (CO2) emission from anthropogenic sources, CO2 sequestration has become an attractive choice to mitigate the emission. Some popular storage media for CO2 are oil reservoirs, deep coal-bed, deep oceanic-beds. These have been used for the long term CO2 storage. Due to special lowering viscosity and surface tension property of CO2, it has been widely used for enhanced oil recovery. The sites for CO2 sequestration or enhanced oil recovery mostly consist of porous rocks. In this thesis work, I focus on understanding the flow through porous at pore-level using variational approach.

Variational approach is …

Experimental And Analytical Study Of The Surface Texturing Enhanced Lubrication Elements, Yifan Qiu

LSU Doctoral Dissertations

Surface texturing is a method that modifies the frictional surface of a nominally flat tribocomponent by shallow patterns. It is found that with added patterns to the surface of a mechanical face seal or thrust bearing, their tribological performance improves, i.e. both friction and wear rate decrease. The current research concentrates on the analysis of hydrodynamic effect responsible for the performance enhancement of the spiral groove patterns and dimples on mechanical seal-like structures and the experimental evaluation of the tribological behavior of these structures. Surface textures considered are: dimple texture and spiral groove pattern. In the research on the dimple …

Model-Based Nonlinear Control Of Active Tilting-Pad Bearings, An Wu

LSU Doctoral Dissertations

A promising mechanical bearing candidate for active operation is the tilting-pad bearing. The proposed active tilting-pad bearing has linear actuators that radially translate each pad. The use of feedback control in determining the actuator forces allows for the automatic, continuous adjustment of the pad position during the operation of the rotating machine. In the first part of the dissertation, we develop a nonlinear dynamic model of the active bearing system. The hydrodynamic force produced by the fluid film is modeled as a nonlinear, squeeze-film damper plus repellent spring. A model-based nonlinear controller is then designed to exponentially regulate the rotor …

The Effect Of Anisotropic Surface Energy On The Stability Of Micro And Nano Wires, Ping Du

LSU Doctoral Dissertations

A liquid thread of radius R will break up into drops if the axial wavelength of the surface perturbation L > 2πR. If L < 2πR, the thread is stable and will remain intact. This is Rayleigh’s stability criterion based on a continuum model. We use molecular dynamics to simulate the evolution of Lennard-Jones liquid threads with equilibrium radius R = 2.3-6.6, where R has been non-dimensionalized by the distance at which the Lennard-Jones potential equals zero. We find that if R is fixed, the wavelength L is bounded by L_min and L_max. For L > L_max the thread always breaks up and stays as drops, and for L < L_min the thread remains intact. However, for L_min < L < L_max, the thread oscillates continuously among several shapes. The appearance of various shapes can be explained by the energy fluctuation of the system.

We also simulate the evolution of Lennard-Jones nanowires with equilibrium radius R = 1.57, 2.58, 3.59, and 4.60 by molecular dynamics. The wires …

Modeling And Simulation For Shape Memory Polymer Based Self-Healing Syntactic Foam, Wei Xu

LSU Doctoral Dissertations

Syntactic foams, renowned for their low density and high mechanical properties, are enjoying continuing growth in various civilian and military sectors. However, like laminated composites, foam cored structures are vulnerable to impact damages and suffering from inabilities in repairing macro-scale cracks. A self-healing mechanism for structural damage is genuinely desired. A recent development in self-healing structural damage is a two-step close then heal (CTH) scheme proposed by Li and Nettles [1] and elucidated by Li and Uppu [2], by mimicking the self-healing process of human skin. This concept has been further demonstrated in Nji and Li’s work [3] that a …

Phase Investigation Of Zirconia Fibers And Their Applications On Solid Oxide Fuel Cells (Sofcs), Luping Li

LSU Master's Theses

Pure zirconia nanofibers were fabricated by electrospinning zirconia-polymer precursor and subsequent annealing. Fiber properties such as polymer decomposition, crystallization formation, phase transformation, surface morphologies, etc., were investigated by various techniques, including thermogravimetric analysis (TGA) and differential thermal analysis (DTA), high temperature differential scanning calorimeter (HTDSC), powder X-ray diffractometer (XRD), field emission scanning electron microscopy (FESEM), etc. It was found the crystallization of as-spun fibers started at 450 °C and the initial crystallized zirconia phase was tetragonal (t), which began transforming to monoclinic (m) phase at 650 °C as evidenced by XRD; HTDSC showed at different thermal circles, the m-to-t transformation …

A Portable Phonatory Feedback Device For Patients With Speech Disorders, Richie Sajan

LSU Master's Theses

Vocal intensity-related speech disorders such as dysarthria and vocal nodules can limit quality of life and reduce the patient’s ability to interact with family, socialize, or pursue employment. Behavioral speech therapies exist to address these issues but have limited effectiveness because they are expensive and clinic-based. The ability to monitor vocal intensity outside of the clinical setting will greatly aid in the treatment of these speech disorders, enabling patients to make quicker progress by reinforcing techniques learned in the clinic. The Voice Volume Monitor (VVM) is a portable and cost-effective therapeutic aid designed for this purpose, providing real-time feedback regarding …

Uv-Lithographic Patterning Of Micro-Features On A Conical Mold Insert, Justin P. Huber

University of Kentucky Master's Theses

In past studies, several techniques have been employed to create microscopic features on relatively simple surfaces. Of these, lithography-based techniques have proven effective at manufacturing large fields of deterministic microasperities and microcavities on planar and cylindrical substrates. The present study focuses on adapting UV-lithography to a more complex substrate. Machined from stainless steel, a conical mold insert introduces an interesting geometry designed for the injection molding of radial lip seal elastomer. The distinct shape of this mold insert poises unique challenges to a conventional lithography procedure. Spray application is investigated as a feasible means to deposit layers of photoresist on …

Sustainable Resource Utilization In Manufacturing Of Printed Circuit Board Assembly: Exergy Analysis Of The Process, Subramaniam Saiganesh

University of Kentucky Master's Theses

Engineering for sustainable development requires prudent utilization of resources under economic, environmental and societal constraints. Resource utilization must follow a holistic approach. This brings in a need for comprehensive metrics which are simple, standard and universal. Thermodynamics may offer a metric that focuses on both quality and quantity of energy resources which may carry information to be combined with other metrics. This metric may be a thermodynamic property called exergy or available energy, which provides a better insight into resource use in both energy and non-energy producing systems. This thesis is devoted to a study of the exergy concept in …

Interfacial Thermal Conductivity Using Multiwall Carbon Nanotubes, Carissa Don Russell

University of Kentucky Master's Theses

Shrinking volume, coupled with higher performance, microprocessors and integrated circuits have led to serious heat dissipation issues. In an effort to mitigate the excessive amounts of waste heat and ensure electronic survivability, heat sinks and spreaders are incorporated into heat generating device structures. This inevitability creates a thermal pathway through an interface. Thermal interfaces can possess serious thermal resistances for heat conduction. The introduction of a thermal interface material (TIM) can drastically increase the thermal performance of the component. Exceptional thermal properties of multiwall carbon nanotubes (MWCNTs) have spurred interest in their use as TIMs. MWCNTs inherently grow in vertically-oriented, …

Characterization Of Ni-Rich Nitihf Based High Temperature Shape Memory Alloys, Gurdish S. Ded

University of Kentucky Master's Theses

Among the potential high temperature shape memory alloys, due to its low cost, medium ductility and high work output NiTiHf seems to be the most promising HTSMA for a wide range of applications in the 100-250ºC. A detailed investigation into the shape memory properties and transformation behavior for the Ni-rich HTSMA with the compositions of Ni_45.3Cu₅Ti_29.7Hf₂₀, Ni_50.3Ti_29.7Hf₂₀ and Ni_45.3Pd₅Ti_29.7Hf₂₀ was carried out. It is possible to form Ni-rich precipitates in Ni-rich NiTiHf alloys and tailor the TTs by heat treatments …

Characterization Of Composite Piezoelectric Materials For Smart Joint Applications, Hari Prasad Konka

LSU Master's Theses

Piezoelectric materials have the ability to provide desired transformation from mechanical to electrical energy and vice versa. When a mechanical force is applied to the piezoelectric material an electrical voltage is generated and when an electrical voltage is applied to the piezoelectric material it gets strained or deformed. Owing to these characteristics piezoelectric materials can be used as a sensor, an actuator, as well as a power generation unit. The high brittleness property of the original piezoelectric material is one of the major constraints in using them in the engineering applications. In order to overcome this disadvantage the composite piezoelectric …

Elastohydrodynamic Analysis Of Spur Gears Using Load-Sharing Concept: Running-In And Steady-State, Saleh Akbarzadeh

LSU Doctoral Dissertations

Gears are widely used in industry and hence their performance is of vital importance. Under the typical operating conditions of gears, the lubricant layer formed between the teeth of the pinion and the gear cannot completely separate the surfaces and contact of asperities of the pinion and gear occurs. This case is usually referred to as mixed lubrication problem. In this research the load-sharing concept has been employed to predict the performance of the pinion-gear system. The load-sharing concept is an efficient method to solve the mixed lubrication problem and is capable to predict the thickness of the lubricant film, …

Macroinstability And Perturbation In Turbulent Stirred Tank Flows, Somnath Roy

LSU Doctoral Dissertations

Impeller stirred tank reactors (STRs) are commonly used in the chemical processing industries for a variety of mixing and blending technologies. In this research, a numerical study of flow and mixing inside turbulently agitated STRs are carried out. An immersed boundary method (IBM) is utilized to represent moving impeller geometries in the background of multi-block structured curvilinear fluid. The IBM This curvilinear-IBM methodology is further combined with the large eddy simulation (LES) technique to address the issue of modeling unsteady turbulent flows in the STR. Verification of the combined IBM-LES implementation strategy in curvilinear coordinates is done through comparisons with …

Degradation Behavior Of Shape Memory Polymer Due To Water And Diesel Fuel, Mohammad Nazmul Hasan Nahid

LSU Master's Theses

Shape memory polymers (SMP) are smart materials, which have the ability to memorize the original or permanent shape. Owing to this characteristic SMP can be used as a sensor, a transplant, as well as structural materials in wide range of applications. Despite its importance, its degradation behavior is still not completely known; and only a limited amount of work has been reported in the literature. In this thesis, the experiments have been carried out to evaluate the degradation behavior of Veriflex- SMP (industry supplied SMP samples) upon exposure to two different types of liquids; water and diesel fuel separately. It …

Near-Field Radiative Transfer: Thermal Radiation, Thermophotovoltaic Power Generation And Optical Characterization, Mathieu Francoeur

University of Kentucky Doctoral Dissertations

This dissertation focuses on near-field radiative transfer, which can be defined as the discipline concerned with energy transfer via electromagnetic waves at sub-wavelength distances. Three specific subjects related to this discipline are investigated, namely nearfield thermal radiation, nanoscale-gap thermophotovoltaic (nano-TPV) power generation and optical characterization. An algorithm for the solution of near-field thermal radiation problems in one-dimensional layered media is developed, and several tests are performed showing the accuracy, consistency and versatility of the procedure. The possibility of tuning near-field radiative heat transfer via thin films supporting surface phononpolaritons (SPhPs) in the infrared is afterwards investigated via the computation of …