Mechanical Engineering Commons^™

Measurement Sensitivity In Tapping-Mode Atomic Force Microscopy Using A Bi-Harmonic Drive Signal, Santosh R. Kodandarama, Douglas A. Bristow

Mechanical and Aerospace Engineering Faculty Research & Creative Works

In tapping mode atomic force microscopy, surface features are measured indirectly via the amplitude of the tapping cantilever. a change in surface profile is detectable only if it results in an amplitude change that is significant enough to be measured by the optics. Previous works have focused on improving sensitivity through the system's Q-factor, either by changing physical cantilever properties or using feedback control, but those approaches undesirably slow down the dynamic response. in this work we take a novel approach to sensitivity amplification by reshaping the tapping trajectory. by shaping the trajectory so that the probe spends a greater …

A Comparison Of Hemodynamic Performance In Mehcanical And Biological Heart Valve Prostheses, Philip Mathew

Masters Theses and Doctoral Dissertations

Heart valve prostheses are used to replace heart valves in patients afflicted with valvular heart disease. The malfunctioning heart valve adversely affects the fluid mechanical performance. While the choice of mechanical VS biological valve prostheses is dependent on the patient, the biological valves should have improved hemodynamic performance compared to the mechanical valves. This work focused on CFD analysis of the Starr-Edwards caged ball valve and a biological valve and serves to validate the improved hemodynamics of the latter valve in comparison to the former. Commercial CFD software (CFD-GEOM, CFD-ACE, CFD-VIEW) are used for the analys is. The main results …

An Investigation On Pulsing Performance Of Mn Class Bi-Propellant Thrusters, Carlos Francisco Gomez

Open Access Theses & Dissertations

With the advancement of technology and machining methods, considerable attention has been focused in manufacturing micro thrusters for micro spacecraft applications (Yetter et al, 2003). Micro propulsion systems are currently being investigated for Miniature Kill Vehicles (MKV) and Micro Satellite Systems (MSS) with an emphasis in reducing weight and cost but without affecting performance. Reducing the weight seems practical when reducing the size of the propulsion system, but problems are encountered with system design.

In addition, propulsion requirements strongly influence choice in propellant and complexity. A thorough understanding of stabilizing thrust levels and the ability to control the propulsion system …

Simulation Algorithm And Validation Of A Photovoltaic Water Pumping System, I. Odeh, Y. Yohannis, Brian Norton

Articles

A photovoltaic (PV) water pumping system has been modelled using TRNSYS considering a power supply, a direct current (DC)/alternating current (AC) inverter, an AC induction motor, a centrifugal pump, a well, a water storage tank, and an overflow protection device. The model emulates actual pumping head curves, uses numerical methods to determine pump system working points, and includes a storage tank as a component in the system. It simulates PV-powered water pumping systems, constant voltage tracking, voltage frequency modulation, and maximum power point tracking algorithms; variable inverter frequency with variable motor efficiency, variable inverter frequency with constant motor efficiency, and …

Multi-Objective Optimization Of Mechanical Elements Using Artificial Bee Colony Optimization Technique, Vimal J. Savsani, R V. Rao, D P. Vakharia

Early Career Technical Journal (ECTJ)

Proceedings of the ASME Early Career Technical Conference, October 1-2, 2010. Woodruff School of Mechanical Engineering, Georgia Institute of Technology, Atlanta, Georgia

pp. 146-152

Test 1979: Kubota M100x, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Test 1981: New Holland Ts6020, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Test 1978: Massey Ferguson 2680hd, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Test 1975: Massey Ferguson 2650hd, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Test 1969: John Deere 8295r, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Test 1976: Massey Ferguson 2660hd, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Test 1967: John Deere 8245r, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Test 1966: John Deere 8225r, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Test 1972: John Deere 8345r, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Test 1968: John Deere 8270r, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Structural Health Monitoring With Piezoelectric Wafer Active Sensors—Predictive Modeling And Simulation, Victor Giurgiutiu

Faculty Publications

This paper starts a review of the state of the art in structural health monitoring with piezoelectric wafer active sensors and follows with highlighting the limitations of the current approaches which are predominantly experimental. Subsequently, the paper examines the needs for developing a predictive modeling methodology that would allow to perform extensive parameter studies to determine the sensing method’s sensitivity to damage and insensitivity to confounding factors such as environmental changes, vibrations, and structural manufacturing variability. The thesis is made that such a predictive methodology should be multi-scale and multi-domain, thus encompassing the modeling of structure, sensors, electronics, and power …

Structural Health Monitoring With Piezoelectric Wafer Active Sensors--Predictive Modeling And Simulation, Victor Giurgiutiu

Faculty Publications

This paper starts a review of the state of the art in structural health monitoring with piezoelectric wafer active sensors and follows with highlighting the limitations of the current approaches which are predominantly experimental. Subsequently, the paper examines the needs for developing a predictive modeling methodology that would allow to perform extensive parameter studies to determine the sensing method’s sensitivity to damage and insensitivity to confounding factors such as environmental changes, vibrations, and structural manufacturing variability. The thesis is made that such a predictive methodology should be multi-scale and multi-domain, thus encompassing the modeling of structure, sensors, electronics, and power …

Nebraska Summary: S779 Tym T603, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Nebraska Summary: S777 Massey Ferguson 7480, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Nebraska Summary: S774 Massey Ferguson 6480, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Nebraska Summary: S773 Massey Ferguson 6475, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Nebraska Summary: S772 Massey Ferguson 6465, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

A Novel Image Processing Platform Development For Preprocessing Images With Two-Phase Microstructures Containing Isolated Particles, Yuxiu Zhang

Wayne State University Theses

A novel image processing platform is developed in this thesis for pre-processing the images of two-phase microstructures containing isolated particles based on Matlab®. The two phases in this work represent martensite particles and ferrite matrix in Dual Phase steels that are developed for lightweight automotive body structures. An automated image processing tool is useful for obtaining statistical microstructure characteristics, important for better understanding material's deformation and fracture behavior. However, a generalized commercial software can not automatically realize the microstructural features of special interest, and a user-specified pre-processing tool is needed.

This platform utilizes the Matlab® GUI technique, Matlab image processing …

Effect Of Alternative Fuels On Aftertreatment Device, Bunpreet Singh

Wayne State University Theses

EFFECT OF ALTERNATIVE FUELS ON THE AFTERTREATMENT DEVICE.

by

BUNPREET SINGH

Dec 2010

Advisor: Dr. Dinu Taraza

Major: Mechanical Engineering

Degree: Master of Science

There is no doubt that globally, alternative fuels have attained the center of attention in order to reduce the dependency on fossil fuels. A lot of research has been conducted on the alternative fuels in the automotive industry pertaining to the sustainability, engine performance and the emission characteristics.

The focus of this study is to investigate the effect of alternative fuels (JP8, Soy-based B20, and S8) on the aftertreatment device. Different fuel properties (both physical and …

Test 1973: John Deere 8345 Rt Ivt, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Newsletter 43 Issue 3 - Fall 2010 - Nuts And Bolts

Friends of the Larsen Tractor Museum

No abstract provided.

Crack Nucleation In A Peridynamic Solid, S. A. Silling, O. Weckner, E. Askari, Florin Bobaru Ph.D.

Department of Engineering Mechanics: Faculty Publications

A condition for the emergence of a discontinuity in an elastic peridynamic body is proposed, resulting in a material stability condition for crack nucleation. The condition is derived by determining whether a small discontinuity in displacement, superposed on a possibly large deformation, grows over time. Stability is shown to be determined by the sign of the eigenvalues of a tensor field that depends only on the linearized material properties. This condition for nucleation of a discontinuity in displacement can be interpreted in terms of the dynamic stability of plane waves with very short wavelength. A numerical example illustrates that cracks …

Influence Of Interactions Between Turbulence And Radiation On Transmissivities In Hypersonic Turbulent Boundary Layers, A. M. Feldick, L. (Lian) Duan, M. F. Modest, M. P. Martín, D. A. Levin

Mechanical and Aerospace Engineering Faculty Research & Creative Works

In the current paper, a high-fidelity large eddy simulation solver is coupled to our modified line-by-line radiative transport equation solver to study the effects of absorption turbulence-radiation interations in a hypersonic turbulent boundary layer, representative of the Orion CEV entering Earth's atmosphere, at peak heating condition. The turbulent and radiation fields represent extreme conditions typical of Orion, as the simulated boundary layer represents the region of high turbulence coupled to region of highest incident radiation. A simplification in the calculation of molecular spectra with a single temperature property database in allows for tractable calculation of spectral properties. A comparison of …

Direct Numerical Simulation Of Hypersonic Turbulent Boundary Layers. Part 2. Effect Of Wall Temperature, L. (Lian) Duan, I. Beekman, M. P. Martín

Mechanical and Aerospace Engineering Faculty Research & Creative Works

In this paper, we perform direct numerical simulation (DNS) of turbulent boundary layers at Mach 5 with the ratio of wall-to-edge temperature T w/T ℘ from 1.0 to 5.4 (Cases M5T1 to M5T5). The influence of wall cooling on Morkovin's scaling, Walz's equation, the standard and modified strong Reynolds analogies, turbulent kinetic energy budgets, compressibility effects and near-wall coherent structures is assessed. We find that many of the scaling relations used to express adiabatic compressible boundary-layer statistics in terms of incompressible boundary layers also hold for non-adiabatic cases. Compressibility effects are enhanced by wall cooling but remain insignificant, and the …

Direct Detection Of No Produced By High-Temperature Surface-Catalyzed Atom Recombination, Dušan A. Pejaković, Jochen Marschall, Lian Duan, Maria P. Martin

Mechanical and Aerospace Engineering Faculty Research & Creative Works

The surface-catalytic recombination of oxygen and nitrogen atoms to form nitric oxide was confirmed by the direct detection of product NO molecules, using single-photon laser-induced fluorescence spectroscopy. Experiments were performed from room temperature to 1200 K in a quartz diffusion-tube sidearm reactor enclosed in a high temperature tube furnace. Atomic nitrogen was generated using a microwave discharge, and atomic oxygen was produced via the rapid gas-phase titration reaction N + NO → O + N2. The use of isotopically labeled titration gases 15N16O and 15N18O allowed for the unambiguous identification of nitric oxide produced by the O + N surface …