Mechanical Engineering Commons^™

High Strain Rate Characteristics Of Rubber Modified Syntactic Foams, Paul Wehmer

LSU Master's Theses

This thesis deals with the characterization of hybrid syntactic foams under high strain rates (HSR) ranging from 450/s to 1000/s. The foams studied are comprised of epoxy resin matrix filled with 63% volume fraction glass microspheres and 2% volume fraction of ground rubber fragments. The focus of this study is to compare the strength, ultimate strain, and modulus of these composite materials at high strain rates and quasi-static conditions and to find out the effects of HSR on the failure mode and fracture behavior of these materials. Split Hopkinson Pressure Bar (SHPB) apparatus is used for the HSR testing. Foams …

Experimental And Numerical Investigation Of Fluid Flow And Heat Transfer In Microchannels, Wynn Allen Phillips

LSU Master's Theses

Microchannels are of current interest for use in heat exchangers where very high heat transfer performance is desired. Microchannels provide very high heat transfer coefficients because of their small hydraulic diameters. In this study, an investigation of fluid flow and heat transfer in microchannels is conducted. A review of the literature published regarding fluid flow and heat transfer in microchannels is provided in this study. A thorough background on the theory of internal convective heat transfer is provided as well. A critical analysis of some of the published heat transfer experiments on microchannels is also given. It was found that …

Nanoclay Syntactic Foam Composites, Sameer Leo Peter

LSU Master's Theses

Syntactic foams are composite materials in which the matrix phase is reinforced with hollow particles called microballoons. They possess low moisture absorption, low thermal conductivity and high damage tolerance because of their compositions. Traditionally, syntactic foams are used in many high strength applications such as in aerospace and marine industries, thus there is a need to achieve both high compressive strength and high fracture strain with minimal increase in density. This research studies the effect of nanoclay on the high strain rate mechanical properties of syntactic foams. Nanoclay reinforced syntactic foams are fabricated by adding 1, 2 and 5% volume …

Design, Fabrication, And Testing Of A Micro Fuel Injection Swirler For Lean Premixed Combustion In Gas Turbine Engines, Anthony Louis Giglio

LSU Master's Theses

Due to growing energy demands and the need for increased fuel consumption efficiency, environmental protection agencies are imposing more stringent emissions regulations on gas turbine combustion systems with emphasis on NOx emissions reduction. Emerging technological combustion schemes to reduce NOx commonly employ lean premixed combustion. Decreases in NOx are globally obtained by flame temperature decrease and locally improved by homogeneity of the reacting mixture. A new micro fuel injection swirler, capable of providing efficient and rapid mixing over a short distance, is presented in this thesis. The conception of the Micro Fuel Injection Swirler (MFIS) was motivated by the need …

Freezing Processes In Cell Suspensions Evaluated Using Cryomicroscopy, Tathagata Acharya

LSU Master's Theses

This thesis aims at evaluating the freezing response of three different cell types, Pacific Oyster embryos, Jurkats and Helas, using the technique of cryomicroscopy. The choice of cells was primarily based on supporting ongoing research work at the Bioengineering Laboratory, Department of Mechanical Engineering at Louisiana State University in Baton Rouge. On a secondary basis, the cells were chosen based on their contrasting nature. While Pacific Oyster being a favorite food in USA calls for successful techniques of cryopreservation of their embryos in order to keep up with the growing demand, Jurkat and HeLa are undesired malignant human cells that …

Quasi-Static And Impact Characterization Of Sandwich Structures With An Iso-Grid Stiffened Syntactic Foam Core, Venkata Sandeep Chakka

LSU Master's Theses

In this study, a novel hybrid sandwich structure with an integrated, iso-grid stiffened syntactic foam core was fabricated and evaluated by impact test and static test. Sandwich beams with different grid cell areas were prepared using a pin-guided dry weaving process. Low velocity impact test on different locations (rib, node, and bay) was conducted with varying hammer weight and impact velocities by an instrumented impact testing machine. Ultrasonic C-scan was utilized before and after impact to identify the damage induced by impact. Scanning Electron Microscopy observation was also implemented to visualize the impact damage at micro- length scale. Compressions after …

Test 1941: John Deere 9330 Diesel, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

A Precision Instrument For Research Into Nanolithographic Techniques Using Field-Emitted Electron Beams, King-Fu Hii

University of Kentucky Doctoral Dissertations

Nanomanufacturing is an active research area in academia and industry due to the ever-growing demands for precision surface modifications of thin films or substrates with nanoscale features. Conventional lithographic techniques face many challenges as they approach their fundamental limits. Consequently, new nanomanufacturing tools, fabrication techniques, and precision instruments are being explored and developed to meet these challenges. It has been hypothesized that direct-write nanolithography might be achieved by using a field-emitted electron beam for nanomachining. This dissertation moves this research one step closer by developing a precision instrument that can enable the integration of direct-write nanolithography by a field-emitted electron …

Photolithography Based Patterning Of Bacteriorhodopsin Films, Christopher M. Anton

Dissertations, Master's Theses and Master's Reports - Open

The patterning of photoactive purple membrane (PM) films onto electronic substrates to create a biologically based light detection device was investigated. This research is part of a larger collaborative effort to develop a miniaturized toxin detection platform. This platform will utilize PM films containing the photoactive protein bacteriorhodopsin to convert light energy to electrical energy.

Following an effort to pattern PM films using focused ion beam machining, the photolithography based bacteriorhodopsin patterning technique (PBBPT) was developed. This technique utilizes conventional photolithography techniques to pattern oriented PM films onto flat substrates. After the basic patterning process was developed, studies were conducted …

Bislug Flow In Circular And Noncircular Channels And The Role Of Interface Stretching On Energy Dissipation, Joseph E. Hernandez

Dissertations, Master's Theses and Master's Reports - Open

The area of microfluidics has increased in popularity with such fields as MEMS, microreactors, microscaleheat exchangers, etc. A comprehensive understanding of dissipation mechanisms for fluid flow in microchannels is required to accurately predict the behavior in these small systems. Tests were performed using a constant pressure potential created by two immiscible fluids juxtaposed in a microchannel. This study focused on the flow and dissipation mechanisms in round and square microchannels. There are four major dissipation mechanisms in slug flow; wall shear, dissipation at the contact line, menisci interaction and the stretching of the interface. A force balance between the internal …

Carbon Conversion During Bubbling Fluidized Bed Gasification Of Biomass, Kevin Timmer

Faculty Work Comprehensive List

Gasification is one means of transforming biomass so that it can be more easily utilized as a renewable source of thermal energy, transportation fuel, and chemicals. Under typical gasification conditions it is not uncommon that a portion of the carbon entering with the biomass leaves the reactor unconverted as char. Understanding and improving carbon conversion during biomass gasification in an atmospheric bubbling fluidized bed reactor is the focus of this study.

To better understand the intricacies of biomass gasification a carbon conversion analytic methodology was developed. The methodology is based on a mass balance of the fixed carbon entering and …

American Electric Power, Jun-Ki Choi, Bhavik R. Bakshi

Mechanical and Aerospace Engineering Faculty Publications

The Encyclopedia of Global Warming and Climate Change helps readers learn about the astonishingly intricate processes that make ours the only planet known to be habitable. These three volumes include more than 750 articles that explore major topics related to global warming and climate change—ranging geographically from the North Pole to the South Pole, and thematically from social effects to scientific causes.

Attribution Of Global Warming, Jun-Ki Choi, Bhavik R. Bakshi

Mechanical and Aerospace Engineering Faculty Publications

The Encyclopedia of Global Warming and Climate Change helps readers learn about the astonishingly intricate processes that make ours the only planet known to be habitable. These three volumes include more than 750 articles that explore major topics related to global warming and climate change—ranging geographically from the North Pole to the South Pole, and thematically from social effects to scientific causes.

Design For Manufacturing For Friction Stir Welding, Harish Bagaitkar

Masters Theses

"This thesis is divided in two parts. In the first part, technical feasibility of implementing Friction Stir Welding (FSW) for automobile chassis fabrication is discussed using a case study. In the case study, Design for Manufacturing (DFM) principles are applied to manufacture an aluminum automobile chassis. Various DFM issues such as Tool Accessibility Issue, Joint Configuration Issue, and Fixture Support Issue along with relevant guidelines such as component geometry change and component elimination are discussed in the first section. Results show that more than 50% of the chassis joints can be welded using FSW technique. The second part of the …

Indication Of Cylinder Pressure Rise Rate By Means Of Vibration And Acoustic Emissions Of An Internal Combustion Engine, Jeffery A. Massey

Masters Theses

"The focus of this study is to investigate the ability of the vibration and acoustic emissions of an internal combustion engine to indicate the cylinder pressure rise rate (PRR). Investigations are conducted on both a small-single cylinder spark-ignition (SI) engine and a larger multi-cylinder compression-ignition (CI) engine. Vibration measurements were made on both engines, however only acoustic measurements were made on the SI engine. Specific vibration and acoustic frequency bands were identified as correlating to energy generated from combustion and energy generated by cylinder cavity resonances"--Abstract, page iii.

Fabrication Of Soy Oil Epoxy Resin Based Composites, Vinay Prabhakar Pai

Masters Theses

"A renewable resource derived epoxidized ester - Epoxidized Allyl Soyate (EAS) yields a versatile epoxy resin system that can be used in pure form combination with bis-phenol epoxy systems to obtain high strength composite materials. EAS containing composites materials exhibit higher toughness and impact resistance than the traditional bis-phenol epoxy composites. These resin systems were found to be compatible with different fibers and screens such as glass fibers, glass mats, carbon fibers and metallic wire screens including those obtained from an automobile tire recycling process. The materials were tested for mechanical properties including tensile and flexure strengths. The highest tensile …

Numerical Study Of Energy Utilization In Nozzle/Plume Flow-Fields Of High-Speed Air-Breathing Vehicles, Althea Grace Wilson

Masters Theses

"Focused local energy deposition in both internal and external flow-fields associated with high-speed aerospace vehicles can provide many system level benefits. This study specifically analyzes the effects of targeted (local) energization of the flow in the nozzle and afterbody flow-field regions of a hypersonic lifting body configuration. Benefits are shown to include the generation of a favorable vehicle pitching moment (nose-down) increment associated with such energy deposition and a reduced local and overall thermal load in both combustor and nozzle for all cases examined. These results have been obtained by modeling the nozzle/afterbody region of a simple generic 2-D wave-rider/lifting …

Femtosecond Laser Micro-Structuring Of Silicon Wafer In Water Confinement, Songping Wu

Masters Theses

"This thesis investigates the use of femtosecond laser induced surface morphology on silicon wafer surface in water confinement. Unlike irradiation of silicon surfaces in the air, there are no laser induced periodic structures, but irregular roughness is formed when the silicon wafer is ablated under water. Interestingly, a particular parameter combination enables a smooth surface, which can improve the surface quality of micro-machining products. This thesis first investigates the single ablation and multi-pulse ablation processes in order to study the effects of laser parameters on ablation morphology, as well as the basic physics and mechanism of the laser-material interaction process …

Individual-Based Artificial Ecosystems For Design And Optimization, Shivakar Vulli

Masters Theses

"Individual-based modeling has gained popularity over the last decade, mainly due to the paradigm's proven ability to address a variety of problems seen in many disciplines, including modeling complex systems from bottom-up, providing relationship between component level and system level parameters, and discovering the emergence of system-level behaviors from simple component level interactions. Availability of computational power to run simulation models with thousands to millions of agents is another driving force in the widespread adoption of individual-based modeling. This thesis proposes an individual-based modeling approach for solving engineering design and optimization problems using artificial ecosystems"--Abstract, page iii.

Fault Propagation Timing Analysis To Aid In The Selection Of Sensors Fro Health Management Systems, Jeremy Johnson

Masters Theses

"Sensor data is processed to assess performance and health of complex systems. Proper sensor selection, placement, and implementation are critical to build an effective health management system. For complex systems in which the timely assessment of the health is desired to avoid expensive consequences of failure, sensor placement is vital. The ability to identify a critical failure early is completely dependent on sensor location within the fault propagation path. A strategy for assessing a sensor suite with respect to timely critical failure detection is presented in this thesis. To illustrate the strategy, Fault Propagation Timing Analysis (FPTA) will be performed …

Sensitivity Analysis Of Relative Worth In Empirical And Simulation-Based Qfd Matrices, Robins Mathai Kalapurackal

Masters Theses

"Quality Function Deployment (QFD) is one of the most popular design tools used in product development. One of the objectives of QFD is to map customer requirements to product requirements and calculate their relative worth. A product requirement with a large relative worth indicates that it is an important product requirement in satisfying customer requirements. QFD applications use various rating scales in quantifying the degree of mapping from customer requirements to product requirements and various worth calculation methods to calculate the relative worth. The purpose of this paper is to study the sensitivity of relative worth when different rating scales …

Sorting Automated Concept Generator Results Based On Manufacture And Assembly Concerns, Kerry Ryan Poppa

Masters Theses

"Early in the design process, it is desirable to produce a large number of potential solutions. Completely exploring a problem's solution space is an unreasonable expectation for an unaided designer or design team. Computational tools have emerged to help designers more fully explore possible solutions. These automated concept generators use knowledge from existing designs and the desired functionality of the new product to suggest solutions. Existing automated concept generation methods produce many candidate solutions, but produce unmanageably large sets of solutions. Techniques are needed to organize the set of concepts into smaller groups, more easily parsed by the human designer. …

Parameter Estimation Of Systems With Deadzone And Deadband And Emulation Using Xpc Target, Jeffrey James Lentz

Masters Theses

"The first paper presents a new approach for online parameter estimation using multiple recursive least squares estimations implemented simultaneously to determine system model parameters, as well as a deadzone and/or deadband. the online adaptive estimation scheme was verified in simulation using MATLAB Simulink and verified experimentally for a DC motor driven cart, an electro-hydraulic pilot valve system, and a free cart loosely coupled to a DC motor driven cart by a pin that fits loosely in a slot...The second paper demonstrates the use of the Mathworks xPC Target environment for validation of a control system and emulation of a physical …

Aflp Fingerprint Analysis Of Hybrid Salamanders In The Missouri Caverns Section Of Onondaga Cave, Maria Louise Potter

Masters Theses

"Two species and one subspecies of salamander in the genus Eurycea, two species of Plethodon and one species of Typhlotriton (recently considered to be Eurycea) salamander currently reside in an area of Onondaga Cave known as the Missouri Caverns section. Due to the presence of two known interbreeding subspecies of salamanders, Eurycea Longicauda (Long-tailed salamander) and Eurycea longicauda melanopleura (Dark-sided salamander), the possibility may exist for interbreeding of one or all of these taxa. Specifically, it is hypothesized that the two species of Eurycea longicauda may interbreed with Eurycea lucifuga (Cave salamander). through visual assessment and phenotypic analysis, …

Development Of A Direct Evaporation Bismuth Hall Thruster, Dean Richard Massey

Dissertations, Master's Theses and Master's Reports - Open

Hall thrusters have been under active development around the world since the 1960’s. Thrusters using traditional propellants such as xenon have been flown on a variety of satellite orbit raising and maintenance missions with an excellent record. To expand the mission envelope, it is necessary to lower the specific impulse of the thrusters but xenon and krypton are poor performers at specific impulses below 1,200 seconds.

To enhance low specific impulse performance, this dissertation examines the development of a Hall-effect thruster which uses bismuth as a propellant. Bismuth, the heaviest non-radioactive element, holds many advantages over noble gas propellants from …

Multiscale Constitutive Modeling Of Polymer Materials, Pavan Kumar Valavala

Dissertations, Master's Theses and Master's Reports - Open

Materials are inherently multi-scale in nature consisting of distinct characteristics at various length scales from atoms to bulk material. There are no widely accepted predictive multi-scale modeling techniques that span from atomic level to bulk relating the effects of the structure at the nanometer (10^-9 meter) on macro-scale properties. Traditional engineering deals with treating matter as continuous with no internal structure. In contrast to engineers, physicists have dealt with matter in its discrete structure at small length scales to understand fundamental behavior of materials. Multiscale modeling is of great scientific and technical importance as it can aid in designing …

Fabrication And Characterization Of Molecular Spintronics Devices, Pawan Tyagi

University of Kentucky Doctoral Dissertations

Fabrication of molecular spin devices with ferromagnetic electrodes coupled with a high spin molecule is an important challenge. This doctoral study concentrated on realizing a novel molecular spin device by the bridging of magnetic molecules between two ferromagnetic metal layers of a ferromagnetic-insulator-ferromagnetic tunnel junction on its exposed pattern edges. At the exposed sides, distance between the two metal electrodes is equal to the insulator film thickness; insulator film thickness can be precisely controlled to match the length of a target molecule. Photolithography and thin-film deposition were utilized to produce a series of tunnel junctions based on molecular electrodes of …

An Integrated Framework For Applying Lean Manufacturing And Other Strategies In Mass Customization Environments, Gregory Brandon Stump

University of Kentucky Master's Theses

Manufacturing organizations are facing fragmented markets and increased demand of variety from consumers. As a result, many of these firms have adopted mass customization manufacturing strategies in an effort to offer their customers the freedom of choice while maintaining operational efficiency. Lean manufacturing strategies have also seen heavy use in manufacturing environments. This study investigates the possibilities of integrating lean manufacturing principles and practices into mass customization environments in order to improve system performance. The feasibility of other manufacturing strategies such as agility, Quick Response Manufacturing and the Theory of Constraints assisting in the application of lean manufacturing for mass …

Performance Optimization Of A Structured Cfd Code - Ghost On Commodity Cluster Architectures, Pavan K. Kristipati

University of Kentucky Master's Theses

This thesis focuses on optimizing the performance of an in-house, structured, 2D CFD code – GHOST, on commodity cluster architectures. The basic philosophy of the work is to optimize the cache usage of the code by implementing efficient coding techniques without changing the underlying numerical algorithm. Various optimization techniques that were implemented and the resulting changes in performance have been presented. Two techniques, external and internal blocking that were implemented earlier to tune the performance of this code have been reviewed. What follows is further tuning effort in order to circumvent the problems associated with using the blocking techniques. Later, …

Elastic-Plastic Indentation Deformation In Homogeneous And Layered Materials: Finite Element Analysis, Siva Naga Venkata Ravi Kiran Kurapati

University of Kentucky Master's Theses

The complex phenomenon of indentation deformation is studied using finite element analysis for both homogeneous and layered materials. For the homogeneous materials, the elastic-plastic deformation at large indentation depth is studied. The variation of the load-displacement curves as well as the variation of the energy ratio with the applied indentation depth for different strain hardening indices is presented. The power law relation between the indentation load and depth for shallow indentation becomes invalid for deep indentation. The ratio of plastic energy to total mechanical work is a linear function of the ratio of residual indentation depth and maximum indentation depth. …