Mechanical Engineering Commons^™

Visualizing The Flow Induced By An Air Curtain Over A Mannequin Using Stereo Particle Image Velocimetry, John Edward Fernandes

Mechanical and Aerospace Engineering Theses - Archive

Air curtains find widespread applications in today's world, such as in malls, supermarkets, airports, cold storage, etc., to allow easy pedestrian movement between two different environments. There is interest in understanding the flow induced by traffic through the air curtain in terms of energy efficiency and the ability to provide isolation from contaminants and airborne pathogens. To develop an understanding of the flow, an initial exploratory study was performed using a static mannequin. A stereo particle image velocimetry (SPIV) system was set up to map the flow of the air curtain, installed on top of the doorway, over a mannequin. …

Characterization Of Thermal Challenges In Electronics : Leakage Current, Co-Architectural Design And Rack Level Cooling, Uthaman Raju

Mechanical and Aerospace Engineering Theses - Archive

Since the advent of transistors and integrated circuits the complexity and functionality of the electronic products has gone up. In line with this, the scaling of the products is catching up at all levels of packaging. Current electronics era is driven by a mantra - "Miniaturization". Recently the number of transistors on high end microprocessor has exceeded a billon mark. The design at board level becomes sophisticated to meet the growing demands. All of these lead to thermal and reliability challenges. A good thermal design is one which makes sure that the chip is operating at its rated frequency or …

Analysis Of Wind Turbine Transverse Vibration, Matt Hein, Whitney Karpen

The Journal of Undergraduate Research

Large wind turbines have become an appealing choice for renewable electrical energy production throughout the world. The United States Midwest contains massive potential for wind energy development and is therefore being primed for large wind turbines to harvest this resource and bring it to market. Because of this, safety concerns have arisen in regard to their ability to withstand the harsh climate of the region. Analysis of the transverse vibration caused by severe weather will be preformed. A simplified model will allow for an analytical solution and displacement graphs produced with MATLAB code. This information will allow for an unbiased …

Cartilage Growth And Remodeling: Modulation Of Balance Between Proteoglycan And Collagen Network In Vitro With Β-Aminopropionitrile, Anna Asanbaeva, Koichi Masuda, Eugene J-M.A. Thonar, Stephen M. Klisch, Robert L. Sah

Mechanical Engineering

Objective

To examine the effect of β-aminopropionitrile (BAPN), an inhibitor of lysyl oxidase, on growth and remodeling of immature articular cartilage in vitro.

Design

Immature bovine articular cartilage explants from the superficial and middle layers were cultured for 13 days in serum-containing medium with or without BAPN. Variations in tissue size, accumulation of proteoglycan and collagen (COL), and tensile mechanical properties were assessed.

Results

The inclusion of serum resulted in expansive tissue growth, stimulation of proteoglycan and COL deposition, and a diminution of tensile integrity. Supplementation of medium with BAPN accentuated this phenotype in terms of a further increase in …

Cal Poly Wind Power Research Center, Patrick Lemieux, John Ridgely

Mechanical Engineering

The Wind Power Research Center is being created at California State Polytechnic University in San Luis Obispo, California. This center brings together faculty, undergraduate and graduate students, and industry partners to conduct applied research and education in support of the wind power industry. Particular emphasis is given to research which serves the needs of manufacturers of smaller wind turbines, and to educating engineers who are well trained to work in all segments of the wind power industry.

A Two-Disk Extended Jeffcott Rotor Model Distinguishing A Shaft Crack From Other Rotating Asymmetries, Xi Wu, Jim Meagher

Mechanical Engineering

A mathematical model of a cracked rotor and an asymmetric rotor with two disks representing a turbine and a generator is utilized to study the vibrations due to imbalance and side load. Nonlinearities typically related with a “breathing” crack are included using a Mayes steering function. Numerical simulations demonstrate how the variations of rotor parameters affect the vibration response and the effect of coupling between torsional and lateral modes. Bode, spectrum, and orbit plots are used to show the differences between the vibration signatures associated with cracked shafts versus asymmetric shafts. Results show how nonlinear lateral-torsional coupling shifts the resonance …

Response Of A Warped Flexible Rotor With A Fluid Bearing, Jim Meagher, Xi Wu, Chris Lencioni

Mechanical Engineering

A two-complex-degrees-of-freedom model is developed and compared to experimental data for various amounts of rotor bow and its orientation to mass imbalance of the rotor. The equation of motion is developed by adding constant forces that rotate with the rotor to a Bently-Muszynska two-mode isotropic rotor model with a plane journal bearing. Diagnostic information discernable from probes at the bearing is explored and compared to midspan response, where previous research has concentrated. The model presented also extends earlier work by representing the effect of a nonrigid bearing. Good agreement between the analytical model and experiment demonstrates that the analysis presented …

Meshless Hemodynamics Modeling And Evolutionary Shape Optimization Of Bypass Grafts Anastomoses, Zaher El Zahab

Electronic Theses and Dissertations

Objectives: The main objective of the current dissertation is to establish a formal shape optimization procedure for a given bypass grafts end-to-side distal anastomosis (ETSDA). The motivation behind this dissertation is that most of the previous ETSDA shape optimization research activities cited in the literature relied on direct optimization approaches that do not guaranty accurate optimization results. Three different ETSDA models are considered herein: The conventional, the Miller cuff, and the hood models. Materials and Methods: The ETSDA shape optimization is driven by three computational objects: a localized collocation meshless method (LCMM) solver, an automated geometry pre-processor, and a genetic-algorithm-based …

An Improved Thermoregulatory Model For Cooling Garment Applications With Transient Metabolic Rates, Johan Westin

Electronic Theses and Dissertations

Current state-of-the-art thermoregulatory models do not predict body temperatures with the accuracies that are required for the development of automatic cooling control in liquid cooling garment (LCG) systems. Automatic cooling control would be beneficial in a variety of space, aviation, military, and industrial environments for optimizing cooling efficiency, for making LCGs as portable and practical as possible, for alleviating the individual from manual cooling control, and for improving thermal comfort and cognitive performance. In this study, we adopt the Fiala thermoregulatory model, which has previously demonstrated state-of-the-art predictive abilities in air environments, for use in LCG environments. We validate the …

Pressure Losses Experienced By Liquid Flow Through Pdms Microchannels With Abrupt Area Changes, Jonathan Wehking

Electronic Theses and Dissertations

Given the surmounting disagreement amongst researchers in the area of liquid flow behavior at the microscale for the past thirty years, this work presents a fundamental approach to analyzing the pressure losses experienced by the laminar flow of water (Re = 7 to Re = 130) through both rectangular straight duct microchannels (of widths ranging from 50 to 130 micrometers), and microchannels with sudden expansions and contractions (with area ratios ranging from 0.4 to 1.0) all with a constant depth of 104 micrometers. The simplified Bernoulli equations for uniform, steady, incompressible, internal duct flow were used to compare flow through …

User-Defined Patterning Of Neural Progenitor Cells On 3d Micropillar Arrays Using Round Cross-Sectional Geometry, Specific Dimen, Andrea Wesser

Electronic Theses and Dissertations

The ability to control stem cell functions, particularly neuronal progenitors, has long since been believed to be the key to successful treatment of neurodegenerative disorders such as Alzheimer's, Parkinson's and accidents involving head trauma. The neurology field calls for many new solutions to address the controlled neural stem cell seeding and placement of cells for neural tissue regeneration. Self-assembled monolayers (SAM) from the alkanethiol group provide a straightforward applicable, reliable treatment for cell adhesion. An ODT/gold treatment was used to adhere the cells to patterned areas, due mainly to a high confluence of cells attracted to it, as well as …

Nebraska Summary: S607 Challenger Mt575b, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Nebraska Summary: S659 Challenger Mt675c Scr, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Nebraska Summary: S657 Challenger Mt655c Scr, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Nebraska Summary: S654 Agco Dt250b, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Nebraska Summary: S687 New Holland T6030 Elite As, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Nebraska Summary: S680 Case-Ih Maxxum 130 Pro, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Nebraska Summary: S674 New Hollang T6050 Elite Pc, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Nebraska Summary: S717 Case-Ih Farmall 85c, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Nebraska Summary: S716 Case-Ih Farmall 75c, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Nebraska Summary: S737 Case-Ih Farmall 105u, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Nebraska Summary: S766 New Holland Td5050, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Tractor Test 1938: New Holland T2330, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Test 1922: John Deere 7230 Diesel, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Test 1936: Case-Ih Magnum 335 Diesel, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Test 1931: Challenger Mt975b Diesel, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Test 1926: John Deere 9630 Diesel, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Analysis Of Gas Dynamic Waves In Explosively Actuated Valves, Blaise H. Paul

LSU Master's Theses

A mathematical model is formulated for assessing quasi-one-dimensional gas dynamics occurring within axis-symmetric explosively actuated valves. The model describes complete valve operation and accounts for pressure-dependent explosive combustion within an actuator, compressible product gas flow within the actuator, through a small port, and into and within a gas expansion chamber. The gas dynamic waves induce piston motion at the terminal end of the expansion chamber which is needed for valve operation. The model is mathematically posed as an initial-boundary-value problem in terms of generalized coordinates to facilitate numerical computations on a domain that volumetrically expands due to combustion and piston …

Nanoclay Reinforced Polymer Composite And Its Application To Hybrid Composite Structures, Gefu Ji

LSU Master's Theses

The purpose of this study was to find the optimum mixing technique that leads to maximum gain in mechanical, thermal, and fire-retardant properties of vinyl ester based nanocomposites. Specifically, five combinations of incremental mixing intensity were applied to five groups of samples that were made of vinyl ester resin reinforced by 1 wt. % of montmorillonite (MMT). Changes in mechanical properties associated with each mixing combination were examined through a variety of tests, which were low velocity impact test, bending test, compression test, and dynamic mechanical analysis (DMA). Additionally, changes in thermal properties (e.g., thermal diffusivity, glass transition temperature) and …

Design And Realization Of An Electrophoretron Cycler, Celine Raymonde Ramet

LSU Master's Theses

Polymerase Chain Reaction (PCR) is a powerful enzymatic reaction commonly used to amplify specific sequences of Deoxyribo Nucleic Acid (DNA). Since the introduction of the lab on a chip concept, numerous Continuous Flow PCR cyclers were realized with success at the micro scale. As reducing the reactor size and improving thermal management led to reduced sample volumes, results could be achieved much faster with these CF-PCR cyclers than with common commercial cycler. Furthermore, most of these demonstrated CF-PCRs are nowadays evolving towards high-throughput systems. However, most CF-PCR cyclers require complex manipulations and are not flexible (e.g. fixed number of cycles, …