Mechanical Engineering Commons^™

3-Dimensional Flow Measurements In Square Coaxial Jets, Thomas Lagarde

LSU Master's Theses

Results from un-forced experiments conducted in the three-dimensional flow emanating from coaxial contoured nozzles with square cross section and parallel sides are presented and discussed. Two experiments were conducted with the inner to outer jet nominal velocity ratio equal to l=0.5 and l=1.5. The Reynolds number of the outer jet based on the hydraulic diameter of the outer nozzle exit was in both cases 16,000. A multi-position hot-wire anemometry method was used for measurements in the three-dimensional turbulent flow using a dual film sensor (X-probe). A methodology was developed and implemented to derive the mean-velocity components and Reynolds stresses corrected …

Modeling And Experimentation Of Drying Of Adipose Derived Adult Stem Cells, Surbhi Mittal

LSU Master's Theses

Development of protocols for storing desiccated cells at ambient temperatures offers tremendous economic and practical advantages over traditional storage procedures such as cryopreservation and freeze-drying. An integrated frame work of experimentation and modeling is adopted in the present work to develop procedures for storage of adult stem cells at ambient temperature. As a first step, we have measured the post-rehydration membrane integrity of two passages, Passage-0 (P0) and Passage-1 (P1), of human adipose-derived stem cells (hASCs). hASCs were dried using a convective stage at three different drying rates (slow, moderate and rapid) in D-PBS with trehalose (50 mM) and glycerol …

Simulations And Experimental Analysis Of High-Aspect-Ratio Diffusive Micro-Mixers, Amit Maha

LSU Master's Theses

Passive (diffusional) mixing has been used in designing high-aspect-ratio micro-mixers for the purpose of performing the Liagase Detection Reaction (LDR). A simple model was used to design such mixers optimized for pressure drop or time required to deliver a prescribed volume of mixture. The types of mixers considered are simple, cheap, and durable and can perform over a broad range of volumetric flow rates at reasonably modest pressure drops. The fluids typically have a very low diffusion coefficient of=1.2x10^10m^2/s, and thus diffusional mixing can only be effective in high-aspect-ratio micro-channels. A realizable aspect ratio of 6 has been considered initially …

Perceived Importance Of National Occupational Cadd Skill Standards Among Faculty Of Nait Accredited Institutions, Ronald Shava

Dissertations and Theses @ UNI

This study presents a descriptive survey that examined the importance and relevance of National Occupational CARD Skills based on the perceptions of faculty teaching at National Association of Industrial Technology (NAIT) accredited institutions. The major goal of the study was to determine what National Occupational CADD Skill Standards are relevant and important to faculty teaching CARD courses. The study was also designed to determine ratings of the perceived importance and relevance of National Occupational CADD Skill Standards by faculty teaching CADD courses at NAIT accredited institutions based on their area of specialization, professional ranking, and teaching experience. This study provided …

Transient Non-Linear Heat Conduction Solution By A Dual Reciprocity Boundary Element Method With An Effective Posteriori Error Estimator, Eduardo Divo, Alain J. Kassab

Publications

A Dual Reciprocity Boundary Element Method is formulated to solve non-linear heat conduction problems. The approach is based on using the Kirchhoff transform along with lagging of the effective non-linear thermal diffusivity. A posteriori error estimate is used to provide effective estimates of the temporal and spatial error. A numerical example is used to demonstrate the approach.

Development And Performance Characteristics Of An Ultrasound Angioplasty Device, Graham Gavin, Garrett Mcguinness, Finbar Dolan, M.S. J. Hashmi

Conference Papers

INTRODUCTION The effect of atherosclerosis is well documented and many procedures such as balloon angioplasty and stentimplantation have been developed to reopen occluded arteries. However, there are considerable differences in the material properties of various atherosclerotic lesions as they develop. Many authors have suggested that rigid calcified plaques may require specific procedures that target this rigid material through de-bulking or complete removal (Salunke et al, 1997). Ultrasound angioplasty is the delivery of high power low frequency ultrasound via a wire waveguide to the lesion location. This results in distal tip wire displacements of up to 100um peak-to-peak (p-p) at frequencies …

Autonomous Vehicle Technologies For Small Fixed-Wing Uavs, Randal Beard, Derek Kingston, Morgan Quigley, Deryl Snyder, Reed Christiansen, Walt Johnson, Timothy Mclain, Michael A. Goodrich

Faculty Publications

The objective of this paper is to describe the design and implementation of a small semi-autonomous fixed-wing unmanned air vehicle. In particular we describe the hardware and software architectures used in the design. We also describe a low weight, low cost autopilot developed at Brigham Young University and the algorithms associated with the autopilot. Novel PDA and voice interfaces to the UAV are described. In addition, we overview our approach to real-time path planning, trajectory generation, and trajectory tracking. The paper is augmented with movie files that demonstrate the functionality of the UAV and its control software.

P-Version Time-Discontinuous Galerkin's Method For Nonlinear Transient Heat Transfer Analysis And Sensitivity Analysis, Ta-Cheng Chien

Mechanical & Aerospace Engineering Theses & Dissertations

The finite element method is a powerful tool for approximating the solution of most engineering problems. Traditionally, the finite element method uses linear approximation of field variables over each element, where numerical results converge to the exact solution by increasing the number of elements. A newer finite element method called the p-version finite element method uses higher-order elements which assume a polynomial of order p for the approximation on each element. Here, the approximation will achieve accuracy without increasing the number of elements but by increasing the value of order p.

The focus of this research is on …

Nonlinear Flutter Of Curved Panels Under Yawed Supersonic Flow Using Finite Elements, Mohamed Salim Azzouz

Mechanical & Aerospace Engineering Theses & Dissertations

In the extensive published literature on panel flutter, a large number of papers are dedicated to investigation of flat plates in the supersonic flow regime. Very few authors have extended their work to flutter of curved panels. The curved geometry generates a pre-flutter behavior, triggering a static deflection due to a static aerodynamic load (SAL) over the panel as well as dynamic characteristics unique to this geometry. The purpose of this dissertation is to provide new insights in the subject of flutter of curved panels. Finite element frequency and time domain methods are developed to predict the pre/post flutter responses …