Mechanical Engineering Commons^™

System And Device For Characterizing Shape Memory Alloy Wires, Robert Ryan Vallance, Bruce L. Walcott, James E. Lumpp, Sumanth Chikkamaranahalli, Osamah A. Rawashdeh, Eric Wolsing

Mechanical Engineering Faculty Patents

Instruments and methods for measuring a property of a shape memory alloy are provided. The instrument includes a base plate, a non-contact movable mass, a force gauge, an actuator, a biasing spring, a heater for heating the shape memory alloy, and a non-contact displacement detector. The biasing spring and the shape memory alloy are disposed whereby a force applied thereby is applied substantially through a center of stiffness of the movable mass. The displacement detector measures a displacement of the movable mass in a colinear direction with a direction of movement of the movable mass and with a direction of …

Integrating Value Stream Mapping And Simulation, Michelle E. Scullin

Theses and Dissertations

An important principle in Lean manufacturing, value stream mapping (VSM) can be helpful in understanding how process flow and information flow affect each other. A VSM is a static picture of a process that allows the user to see where value is added into the value stream. Simulation is used to evaluate the behavioral issues of processes. In a manufacturing realm this means simulation shows how each operation affects other operations so determinations can be made about where bottlenecks or other problems exist in the process. Theoretically, the integration of VSM and Simulation can aide in process improvement by showing …

Ortho-Planar Mechanisms For Microelectromechanical Systems, Craig P. Lusk

Theses and Dissertations

A method for representing the design space of ortho-planar mechanisms has been developed. The method is based on the Theorem of Equality of Orientation Set Measures (TEOSM) which allows mechanisms to be represented by points in an abstract space. The method is first developed for single loop planar folded mechanisms with revolute joints, and later extended to mechanisms with prismatic joints and to spherical folded mechanisms. Functions which assign a value to each point in design space can be used to describe classes of mechanisms and evaluate their utility for MEMS design. Additionally, this work introduces the use of spherical …

Vision-Based Target Localization From A Small, Fixed-Wing Unmanned Air Vehicle, Joshua D. Redding

Theses and Dissertations

Unmanned air vehicles (UAVs) are attracting increased attention as their envelope of suitable tasks expands to include activities such as perimeter tracking, search and rescue assistance, surveillance and reconnaissance. The simplified goal of many of these tasks is to image an object for tracking or information-gathering purposes. The ability to determine the inertial location of a visible, ground-based object without requiring a priori knowledge of its exact location would therefore prove beneficial. This thesis discusses a method of localizing a ground-based object when imaged from a fixed-wing UAV. Using the target's pixel location in an image, with measurements of UAV …

Evaluation Of Accuracy And Efficiency Of Some Simulation And Sampling Methods In Structural Reliability Analysis, Christopher D. Eamon, Michel D. Thompson, Zhenyu Liu

Civil and Environmental Engineering Faculty Research Publications

Numerous simulation and sampling methods can be used to estimate reliability index or failure probability. Some point sampling methods require only a fraction of the computational effort of direct simulation methods. For many of these methods, however, it is not clear what trade-offs in terms of accuracy, precision, and computational effort can be expected, nor for which types of functions they are most suited. This study uses nine procedures to estimate failure probability and reliability index of approximately 200 limit state functions with characteristics common in structural reliability problems. The effects of function linearity, type of random variable distribution, variance, …

Enhancing Student Learning In Mechanics Through Rapid-Feedback, Jennifer Kadlowec, John Chen, Dexter Whittinghill

Mechanical Engineering

In this project our goal is to improve student learning in engineering mechanics courses. The aim to improve learning was accomplished by providing rapid feedback to students of their understanding of key concepts and skills being taught. The feedback system acts as a catalyst to encourage students, working in pairs, to assist each other in correcting misconceptions or deepening each other’s understanding of the concept or skill at hand. Furthermore, the system allows the professor to assess the students’ level of comprehension or misconception in a just-in-time fashion, and thus guide the pace of covering the material. The feedback is …

Flexible Roofing Facility: 2004 Summer Test Results, Florida Solar Energy Center, Danny Parker

FSEC Energy Research Center®

The Flexible Roof Facility (FRF) is a test facility in Cocoa, Florida designed to evaluate five roofing systems at a time against a control roof with black shingles and vented attic (Figure E-1). Since 1989 the testing has evaluated how roofing systems impact summer residential cooling energy use and peak demand. In the summer of 2004, the following roofing systems were tested. Materials tested were: Galvalume® unfinished (unpainted) 5-vee metal with vented attic (3rd year of exposure), galvanized unfinished 5-vee metal with vented attic (3rd year of exposure, black shingles with standard attic ventilation (Control Test Cell), white standing seam …

Study Of Blast Wave Impact On Concrete, Ajit Geevarghese John

Mechanical and Aerospace Engineering Theses - Archive

The past decade has brought an upsurge of terrorist attacks throughout the world. A common form of attack is bombings employed against a civilian structure. These bombs lead to blast waves resulting from high explosive bursts in air, causing severe structural damage to buildings that often collapse before evacuation is possible. These blast waves subject the buildings to repeated dynamic loading in the form of reflecting shock waves which then finally lead to their destruction. Many studies have been carried out to understand the static loading of these structures. The current study is to protect existing buildings from an explosion. …

Research For Dynamic Seal Friction Modeling In Linear Motion Hydraulic Piston Applications, Brian Edward Suisse

Mechanical and Aerospace Engineering Theses - Archive

This paper presents a unique physics-based analytic model for dynamic seal friction in hydraulic actuators as a function of cylinder pressure, seal material, piston rod dimensions, piston rod seal gland dimensions, and other influencing factors. Results from a series of friction tests are presented. Finite element analysis of an installed seal is used to predict contact stress between the seal and the gland, providing a normal force against the sealing surface. This information is used to determine coefficients of friction within the test specimen. From the analysis, a pressure-sensitive model is generated. The friction model is overlaid on the test …

Investigation Of Minimum Response For Damage Assessment, Jeffrey Kirk

Mechanical and Aerospace Engineering Theses - Archive

Assessment of structural damage based on changes in vibratory response characteristics has been researched for many years, with much attention directed toward the use of modal parameters. Modal responses contribute to form points of local minima in the frequency response of a system. The frequency and amplitude values corresponding to these points of minimum response can be analytically determined, experimentally measured, and shown to exhibit sensitivity to damage. This work was performed to investigate the possible contribution that explicitly targeted minimum response information could provide in a damage detection process. A simple 6-DOF discrete spring-mass system was used to conduct …

Design And Fabrication Of A Prototype Fabry-Perot Cavity For The Compton Polarimeter Upgrade At Jefferson Lab, Deepa Deepa

Mechanical & Aerospace Engineering Theses & Dissertations

Upcoming experiments at Hall A at Jefferson lab require 1 % absolute accuracy of the electron beam polarization measurement at 0.85 Ge V energy. The Compton polarimeter at Hall A is capable of measuring beam polarization with 3 - 4 % accuracies at this beam energy. Hence it was proposed to upgrade the present Compton by doubling the laser frequency [2]. The present Compton polarimeter operates with a 1064 nm, continuous wave laser at 200 mW. This power is enhanced to 1.5 kW using a 0.85 m long Fabry-Perot Cavity. Changing to 532 nm laser with the same power would …

Mechanics Of Hydrogenated Amorphous Carbon Deposits From Electron-Beam-Induced Deposition Of Paraffin Precursor, W. Ding, D. A. Dikin, X. Chen, R. D. Piner, R. S. Ruoff, E. Zussman, X. Wang, Xiaodong Li

Faculty Publications

Many experiments on the mechanics of nanostructures require the creation of rigid clamps at specific locations. In this work, electron-beam-induced deposition(EBID) has been used to depositcarbonfilms that are similar to those that have recently been used for clamping nanostructures. The film deposition rate was accelerated by placing a paraffin source of hydrocarbon near the area where the EBIDdeposits were made. High-resolution transmission electron microscopy, electron-energy-loss spectroscopy, Raman spectroscopy, secondary-ion-mass spectrometry, and nanoindentation were used to characterize the chemical composition and the mechanics of the carbonaceous deposits. The typical EBIDdeposit was found to be hydrogenated amorphous carbon (a-C:H) having …

Investigation And Applications Of Latin Hypercube Sampling Methods, Prashant K. Patel

Mechanical & Aerospace Engineering Theses & Dissertations

The Latin hypercube sampling method, sometimes called the stratified sampling method, is a commonly used variance reduction method. Recently, the optimal Latin hypercube sampling method (OLH) and the modified optimal Latin hypercube sampling method (MOLH) are introduced in the literature, which use the genetic algorithm to adjust the distance between sampled points.

This paper will compare the basic Latin hypercube, the optimal Latin hypercube and the modified optimal Latin hypercube methods for generating the sample points for statistical application and curve fitting, in te1ms of accuracy and efficiency. Analytical and structural examples are used in this thesis to facilitate the …

Attribution Standardization For Integrated Concurrent Engineering, Tyson J. Baker

Theses and Dissertations

Product design is a creative process, often subject to rapid and numerous design change requirements. To facilitate geometric redesign iterations, Parametric Computer-Aided Design CAD) systems were introduced. To manage the numerous product design iterations produced by parametric CAD systems, Product Data Management (PDM) systems were developed to capture, document, and manage each product revision. PDM has proved effective thus far at managing design history. However, PDM is built upon database management systems (DBMS), which have the capability of doing far more than simply managing product revision history. Product data consists not only of the physical geometry used to describe it, …

An Analysis Of Microstructure And Corrosion Resistance In Underwater Friction Stir Welded 304l Stainless Steel, Tad Dee Clark

Theses and Dissertations

An effective procedure and parameter window was developed for underwater friction stir welding (UWFSW) 304L stainless steel with a PCBN tool. UWFSW produced statistically significant: increases in yield strengths, decreases in percent elongation. The ultimate tensile strength was found to be significantly higher at certain parameters. Although sigma was identified in the UWFSWs, a significant reduction of sigma was found in UWFSWs compared to ambient FSWs. The degree of sensitization in UWFSWs was evaluated using double loop EPR testing and oxalic acid electro-etched metallography. Results were compared to base metal, ambient FSW, and arc welds. Upper and lower sensitization localization …

Two-Dimensional Grain Boundary Percolation In Alloy 304 Stainless Steel, Brent L. Adams, John A. Basinger, David T. Fullwood, E. R. Homer

Faculty Publications

This work was supported by the MRSEC program of the National Science Foundation under Award Number DMR-0079996. An experimentally-obtained percolation threshold for high-angle random grain boundary networks in alloy 304 stainless steel is compared to thresholds predicted by percolation theory. A discrepancy occurs in the two values (0.46 experimental and 0.65 theoretical). Possible reasons for the discrepancy are explored. The grain boundary network appears to be composed of two distinct sub-networks, with the 'outer' network acting as the dominant contributor to the percolating paths.

An Investigation Of Contact Path And Kinematic Error Of Face-Gear Drives, Tsang-Dong Chung, Yun-Yuan Chang

Journal of Marine Science and Technology–Taiwan

Based on the face-gear generation process, the analytical geometry of face-gear drive with its mathematical model for tooth contact analysis of face-gear and spur pinion meshing was derived. In this paper, contact path and transmission error due to assembly misalignment are analyzed by using the proposed mathematical model and the tooth contact analysis. The effects of assembly error along the axis of face-gear, misalignment of crossed and angular displacement between axes of a spur pinion and a face-gear are all investigated. The results are illustrated by several examples

Collaborative Experimentation And Simulation: A Pathway To Improving Student Conceptualization Of The Essentials Of System Dynamics And Control Theory, Javier A. Kypuros, Thomas J. Connolly

Mechanical Engineering Faculty Publications and Presentations

The overarching goal of this research is to improve conceptualization of System Dynamics and Controls concepts by incorporating a Web-facilitated curriculum to enable intercampus collaboration and remotely-accessible or virtual systems. This approach will complement lecture-based curricula and will strongly enhance students’ conceptualization and exposure to System Dynamics and Controls fundamentals by providing less restricted exposure to a variety of systems that encompass the more important Dynamic Systems concepts. The plan involves the development of a System Dynamics Concepts Inventory and the implementation and assessment of three Web-enabled laboratory formats: (1) inter-campus collaborative experimentation, (2) remotely-accessible experiments, and (3) virtual system …

Introduction To Product Design And Innovation: A Cross Disciplinary Mini Curriculum, Patricia Backer, Seth Bates

Faculty Publications

For the past two years, faculty at San Jose State University (SJSU) have implemented a three- semester minicurriculum in Product Design and Manufacturing. The project follows the Project- Based Learning (PBL) model and is central to the Certificate Program in Product Design in the Mechanical Engineering Department, the Manufacturing Systems concentration in the Department of Aviation and Technology, and the Industrial Design Program in the School of Art and Design. Students in the three courses in the minicurriculum face design challenges while being instructed about the constraints of manufacturability. In each course, students develop three to four products. All products …

The Effectiveness Analysis Of The Online Tools For Engineering Faculty Needs, Ismail Fidan, Jianbiao Pan, Leijun Li

Industrial and Manufacturing Engineering

As the use of Internet is increasing dramatically, many faculty members are using it in their teaching, research, and services. The Internet also provides faculty easy access to employee benefits and other information. Many universities are using or plan to use online teaching. Lately, many editorial and funding agencies have also started to initiate online review and decision-making system. These systems have eased the burden on both reviewers and agencies. In this study, a survey was prepared and conducted to investigate the effectiveness of the online tools for faculty needs in authors’ institutions and some other United States universities. The …

Experimental Nonlinear Tracking Control For Nonholonomic Mobile Robots With Input Constraints, Timothy Mclain, Randal W. Beard, Wei Ren, Ji-Sang Sun

Faculty Publications

This paper presents experimental results of nonlinear trajectory tracking controllers for nonholonomic mobile robots with fixed-wing UAV-like input constraints. Programmed to emulate an unmanned air vehicle flying at constant altitude, a nonholonomic mobile robot is assigned to follow a desired trajectory to transition through a sequence of targets in the presence of static and dynamic threats. Two velocity controllers with input constraints are proposed for tracking control. Hardware results using these two velocity controllers are compared to simulation results of dynamic controllers based on nonsmooth backstepping to demonstrate the effectiveness of our approach.

Effect Of Chaos And Stochastics Induced By Internal Waves On Acoustic Wave Propagation, Tatiana A. Andreeva, William W. Durgin

Office of the Provost Scholarship

In the present paper the eikonal equation is considered in the form of a second order, nonlinear ordinary differential equation with harmonic excitation due to internal wave. The harmonic excitation is taken imperfect, i.e. there is a random phase modulation due to Gaussian white noise. The amplitude and wavelength of the acoustic wave are used as the principle signal characteristics in bifurcation analysis. The regions of instability, identified using the bifurcation diagrams, examined through phase diagrams and Poincare maps. The effect of stochastic nature in addition to chaotic one of internal waves is demonstrated by means of comparison of the …

Development Of High Efficiency Air Conditioner Condenser Fans, Florida Solar Energy Center, Danny Parker

FSEC Energy Research Center®

With sponsorship from the U.S. Department of Energy, a research project has designed, fabricated and tested improvements to an air conditioner outdoor unit fan system. The primary objective was to improve condenser fan performance while reducing motor power. We also examined potential changes to the condenser exhaust configuration to enhance air moving efficiency performance. A secondary objective was to provide sound reductions as lower noise AC equipment is important to consumers.

Within conducted tests, an improved high efficiency fan design and advanced exhaust diffuser section reduced fan motor power requirements by approximately 49 W (26%) while providing superior air flow. …

Sequential Deposition Of Copper/Alumina Composites, X. Wang, J. Ma, A. Maximenko, E.A. Olevsky, M.B. Stern, B.M. Guenin

Industrial and Manufacturing Engineering

No abstract provided.

Introducing Feedback Control To First Year Engineering Students Using Labview, Samuel Bogan Daniels, David Harding, Michael Collura

Mechanical and Industrial Engineering Faculty Publications

This paper discusses the introduction of basic feedback control concepts and applications specifically selected for first year engineering & applied science students. These activities are introduced in the second half of a first semester class that is part of a sequence of first and second year courses used to develop a strong foundation for programs in various engineering disciplines. This sequence of courses uses a Multidisciplinary Engineering Foundation Spiral¹ in the form of a four-semester sequence of engineering courses, matched closely with the development of students’ mathematical sophistication and analytical capabilities and integrated with coursework in the sciences. 1 . …

Stability Of Transport And Rate Processes [Review], Yaşar Demirel

Papers in Thermal Mechanics

About fifty years ago, the Turing instability demonstrated that even simple reaction-diffusion systems might lead to spatial order and differentiation, while the Rayleigh-Bénard instability showed that the maintenance of nonequilibrium might be the source of order in fluids subjected to a thermodynamic force above a critical value. Therefore, distance from global equilibrium in the form of magnitude of a thermodynamic force emerges as another constraint of stability; some systems may enhance perturbations, and evolve to highly organized states called the dissipative structures after a critical distance on the thermodynamic branch. Although the kinetics and transport coefficients represent short-range interactions, chemical …

Evaluation Of A Two Dimensional Analysis Method As A Screening And Evaluation Tool For Anterior Cruciate Ligament Injury, Scott G. Mclean, K. Walker, K. R. Ford, G. D. Myer, T. E. Hewett, Antonie J. Van Den Bogert

Mechanical Engineering Faculty Publications

Background: Increased knee valgus predicts the risk of anterior cruciate ligament (ACL) injury, particularly in women. Reducing injury rates thus relies on detecting and continually evaluating people with relatively large valgus motions.

Objectives: To examine the potential of a two dimensional (2D) video analysis method for screening for excessive valgus.

Methods: Ten female and 10 male National Collegiate Athletic Association basketball players had three dimensional (3D) knee valgus and two dimensional (2D) frontal plane knee angle quantified during side step, side jump, and shuttle run tasks. 3D valgus was quantified from external marker coordinates using standard techniques, and 2D data …

Mercury Experience And Capabilities, University Of North Dakota. Energy And Environmental Research Center

EERC Brochures and Fact Sheets

Brochure about the Energy & Environmental Research Center’s (EERC’s) mercury research capabilities. Describes the EERC facilities and mercury testing technology. [This item is an outdated or superseded version and retained for historical purposes only. It may no longer reflect current information, policies, or practices.]

Special Issue: Engineering Applications Of Representations Of Function, Part 2, Robert B. Stone, Amaresh Chakrabarti

Mechanical and Aerospace Engineering Faculty Research & Creative Works

No abstract provided.

Three-Dimensional Radiative Transfer In An Isotropically Scattering, Plane-Parallel Medium: Generalized X- And Y-Functions, D. W. Mueller, A. L. Crosbie

Mechanical and Aerospace Engineering Faculty Research & Creative Works

The topic of this work is the generalized X- and Y-functions of multidimensional radiative transfer. the physical problem considered is spatially varying, collimated radiation incident on the upper boundary of an isotropically scattering, plane-parallel medium. an integral transform is used to reduce the three-dimensional transport equation to a one-dimensional form, and a modified Ambarzumian's method is used to derive coupled, integro-differential equations for the source functions at the boundaries of the medium. the resulting equations are said to be in double-integral form because the integration is over both angular variables. Numerical results are presented to illustrate the computational characteristics of …