Mechanical Engineering Commons^™

Test 1895: Case Ih Cx 70/C 70 Diesel, Nebraska Tractor Test Lab

Nebraska Tractor Tests

No abstract provided.

Test 1894: Case Ih Cx 60/ C 60 Diesel, Nebraska Tractor Test Lab

Nebraska Tractor Tests

No abstract provided.

Nebraska Summary: S296 New Holland Ts 110, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Bolt Bearing Behavior Of Engineered Wood Composites, Stephen J. Carstens, David Pollock

Faculty Publications - Biomedical, Mechanical, and Civil Engineering

The goal of this research was to gain a better understanding of the bolt bearing behavior of engineered wood composites made from yellow poplar lumber. Lumber specimens included in this study were laminated veneer lumber, strandbased lumber, yellow poplar lumber, and Douglas-fir larch lumber. Testing followed the half-hole and full-hole configuration as set forth in ASTM Standard D5764 (1998).

In a previous study by Wilkinson (1991), a strong correlation was shown between bearing strength perpendicular to grain and bolt diameter. This study supports Wilkinson's finding for bearing strength perpendicular-to-grain based on the half hole test configuration. Other findings in this …

Analysis Of Ductile To Cleavage Transition In Part-Through Cracks Using The Cell Model Incorporating Statistics, Xiaosheng Gao, J. Faleskog, C. Fong Shih

Mechanical Engineering Faculty Research

This paper describes an approach to study ductile/cleavage transition in ferritic steels using the methodology of a cell model for ductile tearing incorporating weakest link statistics. The model takes into account the constraint effects and puts no restriction on the extent of plastic deformation or amount of ductile tearing preceding cleavage failure. The parameters associated with the statistical model are calibrated using experimental cleavage fracture toughness data, and the effect of threshold stress on predicted cleavage fracture probability is investigated. The issue of two approaches to compute Weibull stress, the ‘history approach’ and the ‘current approach’, is also addressed. The …

Spin-Up In A Tank Induced By A Rotating Bluff Body, R. Daniel Maynes, J. Klewicki, P. Mcmurty

Faculty Publications

Spin-up of a turbulent flow in a cylindrical tank caused by a rotating bluff body has been investigated using flow visualization, fluid velocity measurements, and hydrodynamic torque measurements. During the spin-up process three distinct temporal regimes exist. These regimes are: (i) a build-up regime where the torque and the tangential velocity fluctuations in the close proximity of the body remain constant; (ii) a decay regime where these quantities decay with power-law relations; and (iii) a mean flow steady state where these values remain relatively constant. Experiments were conducted in two tanks differing in volume by a factor of 80 and …

The Presence Of Edge Contact And Its Influence On The Debonding Of Patched Panels, Anette M. Karlsson, W. J. Bottega

Mechanical Engineering Faculty Publications

A formulation is presented which accounts for configurations of debonding patched cylindrical panels for which the edge of the debonded segment of the patch maintains sliding contact with the corresponding base structure. The formulation is incorporated with that which accounts for configurations for which a contact zone is present and for which no contact between the debonded segments of the patch and base structure occurs during debonding. Analyses are performed for two types of loading conditions: Applied circumferential tension and applied internal pressure. Results of numerical simulations based on analytical solutions of the problems of interest are presented in the …

Combining Wavelets And Hotelling Transforms In Image Query, Sol Neeman Ph.D.

Engineering Studies Faculty Publications and Creative Works

In the "content based" image query, also referred to as "query by example," "similarity retrieval" or "sketch retrieval," the query image is provided by the user either as a sketch of the object, as the output of a scanner or a video camera. Some of the difficulties associated with content based image query are described in [1], e.g. significant difference between the "query image" and the "target image," artifacts and poor resolution of the query image make a straightforward comparison of images using L1 and l2 metrics not effective.

In [2] a new strategy is suggested based on wavelet decomposition …

Computation Of Flame Base Height Of A Turbulent Diffusion Flame Resulting From A Methane Jet, A. S. Kheireddine, S. K. Chaturvedi, T. O. Mohieldin

Mechanical & Aerospace Engineering Faculty Publications

This work summarizes numerical results for a diffusion flame formed from a cylindrical tube fuel injector, issuing a gaseous methane jet vertically in a quiescent atmosphere. The primary objective is to predict the flame base height and other flame characteristics as a function of the fuel jet velocity. A finite volume scheme is used to discretize the time-averaged Navier-Stokes equations for the reacting flow resulting from the turbulent fuel jet motion. The turbulent stresses, and heat and mass fluxes are computed from a Reynolds stress turbulence model. A chemical kinetics model involving two-step chemistry is employed for the oxidation of …

The Integrated Systems Engineering Laboratory- An Innovative Approach To Vertical Integration Using Modern Instrumentation, Ajay Mahajan, Maurice Walworth, David Mcdonald, Kevin Scmaltz

Mechanical Engineering Faculty Research

The current paradigm in engineering course instruction builds on a lecture prerequisite structure but ignores the need for a laboratory prerequisite structure. Educational quality is therefore diminished as instructors optimize specific laboratories but fail to optimize the overall program laboratory experience. This paper presents a learning environment based on modern instrumentation that forces students to use not only concepts and skills acquired from the lecture, but also actual data and models acquired from lower division laboratories, in upper division laboratories. The vertical integration occurs because students must utilize their previous laboratory work as a reference and/or building blocks as they …

Nebraska Summary 363: Massey Ferguson 8250 Diesel 32-Speed, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA

The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data.

EXPLANATION OF THE TEST PROCEDURES

Purpose

The purpose of …

Nebraska Summary 302: Massey Ferguson 6265 Diesel 32-Speed, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA

The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data.

EXPLANATION OF THE TEST PROCEDURES

Purpose

The purpose of …

Nebraska Summary 305: Massey Ferguson 6290 Diesel 32-Speed, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA

The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data.

EXPLANATION OF THE TEST PROCEDURES

Purpose

The purpose of …

Nebraska Summary 317: Massey Ferguson 263 Diesel 8-Speed, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA

The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data.

EXPLANATION OF THE TEST PROCEDURES

Purpose

The purpose of …

Nebraska Summary 316: Massey Ferguson 243 Diesel 8-Speed, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA

The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data.

EXPLANATION OF THE TEST PROCEDURES

Purpose

The purpose of …

Test 1760: Case Ih Mx 240 Diesel, Nebraska Tractor Test Lab

Nebraska Tractor Tests

No abstract provided.

Test 1761: Case Ih Mx 270 Diesel, Nebraska Tractor Test Lab

Nebraska Tractor Tests

No abstract provided.

Test 1885: New Holland 9282 Quadrasync/New Holland 9184 Quadrasync Diesel, Nebraska Tractor Test Lab

Nebraska Tractor Tests

No abstract provided.

Tests 1910 & 1911: New Holland Tl 80 Diesel, Nebraska Tractor Test Lab

Nebraska Tractor Tests

No abstract provided.

Tests 1914 & 1915: New Holland Tl 90 Diesel, Nebraska Tractor Test Lab

Nebraska Tractor Tests

No abstract provided.

Tests 1908 & 1916: New Holland Tl 100 Diesel, Nebraska Tractor Test Lab

Nebraska Tractor Tests

No abstract provided.

Test 1900 & 1901: New Holland Tn 55d/New Holland Tn 55s Diesel, Nebraska Tractor Test Lab

Nebraska Tractor Tests

No abstract provided.

Tests 1902 & 1903: New Holland Tn 65d/New Holland Tn 65s Diesel, Nebraska Tractor Test Lab

Nebraska Tractor Tests

No abstract provided.

Test 1834: New Holland Ts110 Diesel, Nebraska Tractor Test Lab

Nebraska Tractor Tests

No abstract provided.

Test 1829: New Holland Ts90 Diesel, Nebraska Tractor Test Lab

Nebraska Tractor Tests

No abstract provided.

Test 1886: New Holland Tv-140/New Holland Tv-145 Diesel, Nebraska Tractor Test Lab

Nebraska Tractor Tests

No abstract provided.

Test 1874 & 1878: Challenger Mt 545 Diesel, Nebraska Tractor Test Lab

Nebraska Tractor Tests

No abstract provided.

Tests 1847 & 1848: Challenger Mt 565 Diesel, Nebraska Tractor Test Lab

Nebraska Tractor Tests

No abstract provided.

Test 1869: Challenger Mt 665 Diesel, Nebraska Tractor Test Lab

Nebraska Tractor Tests

No abstract provided.

Test 1762: White 6510 Diesel, Nebraska Tractor Test Lab

Nebraska Tractor Tests

No abstract provided.