Mechanical Engineering Commons^™

Bio-Inspired Wings In High Freestream Turbulence: A Numerical And Experimental Study, Alexia Martinez Ibarra

Theses and Dissertations

The aerodynamics and flow field characteristics of a NACA 0010 airfoil with leading-edge modifications were investigated in flow with freestream turbulence intensity of 4%. A set of 4 airfoils, each of them with different wavelength (4, 8, 10, 12 tubercles along the spanwise direction) was experimentally studied. An unmodified NACA 0010 airfoil was used as baseline. The Reynolds number was varied from 201,200 to 351,600. The angle of attack was varied within the range of -6 to 20 degrees. Several techniques were used to investigate the characteristics of the airfoils such as wake profile surveys, 6-axis force measurements, and Particle …

A Study On Reaction Rate Factors Of A Single-Step Combustion Mechanism For Gasoline Hcci Combustion, Pakawat Panuwatsuk

Theses and Dissertations

Homogeneous Charge Compression Ignition (HCCI) engine has been invented to achieve the advantages of both diesel and gasoline engines. HCCI engine can run with a higher compression ratio like diesel engine in order to achieve high thermal efficiency. Meanwhile, like gasoline engine, the engine produces less NOx gas and particulate matters than diesel engine. However, there are several difficulties associated with HCCI combustion, which still require further development to the engine. The most important issues are autoignition timing and narrow operational range. In order to develop an HCCI engine, a numerical simulation can significantly save cost, time and resources over …

Analysis Of Polyester Interleafs For Toughness Enhancement In Composite Structures, Adnan Gheryani

Theses and Dissertations

Delamination between composite layers is one of primary weaknesses in composite material structure. Various researchers have developed techniques to control delamination in laminated structures. One of these techniques is “interleaving,” adding high toughness material to key interfaces in a laminate. This research studies using polyester veil as a low-cost interleaf alternative to other materials and focuses on a non-woven, polyester spunbond material. Two different interleaf thicknesses, 0.18 mm and 0.74 mm are primarily used. In addition, fine 4 g/m2 polyester was also compared. Carbon/epoxy composites are manufactured using 2x2 Twill 24”-12k carbon fibers embedded in an epoxy resin, with polyester …

Living Docks: Structural Implications And Determination Of Force Coefficients Of Oyster Mats On Dock Pilings In The Indian River Lagoon, Ryan Christiansen

Theses and Dissertations

Brevard County, Florida, is facing rapid population growth and increased pollution entering the Indian River Lagoon (IRL), impairing water quality and damaging the ecosystem. This is problematic not only for public health and environmental stability, but also for the economy. The Living Docks initiative was created to combat environmental degrade in the lagoon and restore natural functions back to the ecosystem. With increased urbanization along coastal systems, there is opportunity for new forms of ecological engineering such as Living Docks, which attaches oyster mats to dock pilings as a means to promote the growth of filter feeding organisms. It is …

Thermal Management Design Of A 6u Cubesat With A High-Power Additive Manufacturing Payload Using Analytical Modeling With Experimental Validation, Todd Wayne Fennell Jr.

Theses and Dissertations

As the capacity of compact battery technology for spacecraft missions continue to improve, small payloads are less constrained by power limitations, thus relatively high-power applications may be considered. AddCube is a mission to develop a platform, conforming to the 6U CubeSat Standard capable of demonstrating on-orbit Additive Manufacturing technology. A critical concern is the development and demonstration of a thermal management design that is capable of handling the significant waste heat generated by the high-power Additive Manufacturing payload while maintaining component temperatures throughout the spacecraft within an acceptable range. This effort includes a trade study for the evaluation of candidate …

Nonlinear Attitude Control For A 6u Cubesat With A Flexible, Deployable Boom, Jared Walker

Theses and Dissertations

A satellite attitude control system was developed in MathWork’s Simulink for a 6U CubeSat with a flexible appendage payload. The flexible appendage is a boom that is able to store into a compact size and deploy out to 1 meter. The boom deploys a sensor attached to the end of the boom. The boom/sensor payload was modeled as a spring-mass-damper system. The equivalent spring constant of the payload was determined by the the natural frequency of the system. A modal analysis in ANSYS Mechanical was used to determine the natural frequencies and mode shapes of the payload. The attitude control …

Examining The Impact Of Student Motivation On Performance In Mechanical Engineering Design Courses, Elisabeth Kames

Theses and Dissertations

Design courses are an integral component of undergraduate engineering education. Design is recognized as one of the primary responsibilities of an engineer in industry. New designs are responsible for stimulating sales and company growth.1 This dissertation outlines a study seeking to explore the impact of student motivation factors on course performance of mechanical engineering students in design courses. The first design course, cornerstone design, takes place during the first semester of freshman year. The second course, capstone design, takes place during the student’s final year of undergraduate study. An adapted version of the Motivated Strategies for Learning Questionnaire (MSLQ) is …

Damage Evaluation Of Rolling Element Bearings For Shipboard Machinery, Brenna Lyn Feirer

Theses and Dissertations

Rolling element bearings perform an essential role in most all rotating machinery. To prevent degradation to machine performance, unforeseen costs and unexpected system failure, bearing fault diagnosis and prognosis are used. Acoustic Emission (AE) introduces high sensitivity, early and rapid detection of cracking, and real time monitoring that can alarm once cracking is noticed.

The purpose of this research is to nondestructively monitor the crack growth in rolling element bearings in a marine environment and to determine the acoustic emission parameters which embody crack initiation and propagation. The intellectual merit lies in:

1. the signal alarm developed from an AE …

Design And Testing Of A Supercritical Carbon Dioxide Plasma Reactor, Gregory Belk

Theses and Dissertations

The objective of this project was to design, build, and test a plasma reactor capable of operating in the supercritical conditions. The reactor allows for the initiation of a plasma discharge in different fluids driven by a direct current (DC) power supply operating either in steady state mode or pulsing mode. The reactor was specifically designed for igniting plasmas within supercritical carbon dioxide, which has a pressure of 72.9 atm and 31.1 degrees Celsius.

A series of runs were conducted for varying pressures and inter-electrode separation, which allowed testing the operation regimes of the reactors. Finally, plasma experiments were conducted …

Design Of Bio-Inspired Multifrequency Acoustic Sensors And Metamaterial Energy Harvesting Smart Structures, Mohammadsadegh Saadatzi

Theses and Dissertations

Due to the limited availability and high depletion rates of nonrenewable sources of energy as well as environmental concerns, the scientific community has started to explore many alternative clean sources of energies. It is identified that civil, mechanical and Aerospace structures are always subjected to acoustic noises and vibration which could potentially be used as renewable source of energy. Roads and Industrial noise barriers are used inside industrial facilities alongside the walls, around construction pillars, nearby machinery and other equipment to separate quite work zones, protect walls, deliver extra safety and precautions while diminish sound and vibrational pressure. We hypothesized …

Tow-Path Characterization For Automated Fiber Placement, Roudy Wehbe

Theses and Dissertations

Automated Fiber Placement (AFP) is a manufacturing process used to fabricate large composite structures for aerospace applications. During the process, the machine head deposits multiple bands of composite material named tows over a prescribed path. Temperature, speed, and compaction pressure can be varied to obtain a good layup quality. For conventional laminated plate structures manufactured using the AFP process, fibers are laid at constant angles (0°, 90°, ±45°) in straight paths. However, to manufacture complex shell structures or variable stiffness plates, curved paths are necessary in the design leading to a length mismatch between the parallel edges of the towpath. …

Kinetic And Multidimensional Transport Coupled Numerical Investigation Of Nox Formation During Syngas And Natural Gas Combustion, Sheikh Farhan Ahmed

Theses and Dissertations

The primary objective of this thesis work is focused on the chemical kinetic modeling of the formation of Oxides of Nitrogen (collectively termed as NOx), regarded as a major pollutant emitted by combustion devices, and the application of that model to simulate transport coupled multidimensional distribution of NOx in a reacting flow. The underlying motivation of this kinetic modeling is the noted discrepancies among the existing models, which become critical in selecting the correct model in advanced gas turbine and engine research. The first part of this work is the performance evaluation and comparison of the existing models. Based on …

The Manufacturing And Characterization Of Pseudo-Woven Carbon Fiber Composite Architectures For Enhanced Damage Tolerance, Cyrus Vakili Rad

Theses and Dissertations

Traditional unidirectional carbon fiber reinforced polymer matrix composites exhibit brittle failure, limited toughness, and poor damage tolerance often resulting in the overdesign of composite systems. This work focuses on the automated fiber placement (AFP) manufacturing and characterization of a new family of pseudo-woven (PW) laminate architectures aimed to enhance impact resistance and damage tolerance. The PW laminate architecture uses a specialized in situ AFP process implementing tow skips to produce its laminate architecture. This results in a heterogeneous architecture possessing spatially variable in-plane material properties unlike traditional laminated composites. This heterogeneity is associated with topological variations in the fiber orientations …

Efficient Design Optimization Methodology For Manufacturable Variable Stiffness Laminated Composite Structures, Mazen Albazzan

Theses and Dissertations

Because of their superior mechanical and environmental properties compared to traditional metals, fiber-reinforced composite materials have earned a widespread acceptance for different structural applications. The tailoring potential of composites to achieve high specific stiffness and strength has promoted them as promising candidates for constructing lightweight structures. From that aspect, designers have tackled the problem of designing composite laminates, which is inherently challenging due to the presence of non-linear, non-convex, and multi-dimensional optimization problems with discrete and continuous design variables. However, despite their increased usage, the possible improvements that can be achieved by composite laminates have not been fully exploited. With …

Acoustic Emission And Guided Wave Modeling And Experiments For Structural Health Monitoring And Non-Destructive Evaluation, Roshan Prakash Joseph

Theses and Dissertations

This dissertation is organized into major parts. In Part I of the dissertation, plate guided waves due to an acoustic emission (AE) event are analytically studied in the context of seismic moment tensor sources. The guided wave propagation elastodynamic equation corresponding to a point source applied to the plate in an arbitrary direction is modified in order to describe the case when the source is a seismic moment tensor of various tensor components. This part of the dissertation also discusses the analytical modeling of AE test sources such as pencil lead break, hammer hit excitation, etc.

In Part II of …

Effects Of Material Characteristics And Equipment Configuration On Profilometry Scanning Results For Error Mitigation In Automated Fiber Placement, Jacob Ondeck

Theses and Dissertations

The Automated Fiber Placement manufacturing process is a method for constructing layered composite parts. This is done by placing tapes of material on a tool using a compaction roller and heat to tackify the material [1]. This manufacturing process is not new, but latest equipment generations can still introduce randomly occurring defects, presenting often as tow twists, gaps, unintentional overlaps and even missing tows during the layup process. These defects deviate the manufactured structure from the as-designed structure, and have been proven to introduce stress concentration sources, which can ultimately undermine the performance of a structure [2]. To detect and …

Strain Components In Friction Stir Extrusion, Megan Ryan

Theses and Dissertations

Friction stir extrusion is a solid state process that uses a rotating die to perform extrusions. This process can be used to directly recycle waste from machining processes and has been shown to produce wires with desirable mechanical properties. In order to better understand the friction stir extrusion process, the effect of the process parameters on the strain distribution in the wires needs to be understood. The process parameters evaluated in this work are die advance rate, die rotational seed, and die geometry. A total of 16 wires were extruded using different combinations of these process parameters. Marker wires were …

Influence Of Dynamic Multiaxial Transverse Loading On Ultrahigh Molecular Weight Polyethylene Single Fiber Failure, Frank David Thomas

Theses and Dissertations

High performance fibers such as ultrahigh molecular weight polyethylene (UHMWPE) are often used for ballistic impact applications in the form of textile fabrics and composite laminates. In order to predict the ballistic performance of such materials, single-fiber experiments are performed to quantify the material behavior at smaller length scales, which can be applied to larger length scales as a result. Failure of UHMWPE is well understood as a function of simple tension at low and high strain rates, as well as under various multiaxial loading states. However, experimental characterization of single UHMWPE fibers under transverse loading at high strain rates …

Characterization Of Reactive Ion Etch Chemistries Using Direct Write Lithography, Dylan T. Martin-Abood

Theses and Dissertations

The DoD requires a variety of COTS and number of custom microelectronics to provide important functionality to critical military systems. Photolithography and DRIE are two techniques commonly used in the development of deep anisotropic features for the fabrication and modification of microelectronics and MEMS. However, standard photolithography techniques are ineffective for unique substrate geometries and DRIE processes require a chemical passivation step only applicable to Si substrates. This work confirmed the capability of RIE using DWL to perform deep, highly selective, anisotropic etching on elevated, non-circular substrates.

Investigation Study Of A Novel Oscillating Thermo-Magneto-Electric Generator, Abdulrahman Mohammed Homadi

Theses and Dissertations

In this dissertation, we present a unique system working as a generator that takes the advantage of waste heat dissipation from an application to generate electricity by induction. This system can be called a thermo-magneto-electric generator (TMEG), because it deals with a heat source, heat sink, and magnetic field generated by a permanent magnet (PM) and works to generate voltage by induction. The magnetic energy is the resource power of this system due to the existence of the magnetic material (ferromagnetic), and the reason of the movement is the change in the amount of magnetic energy repeated by the change …

Examining Career And Technical Education Practitioner Preparation And Professional Development Needs, Shane Wilson Lange

Theses and Dissertations

This quantitative study was used to investigate Illinois automotive educator professional development needs and to identify the demographic landscape of Illinois secondary and post-secondary automotive teachers. The study should bring a greater understanding of what automotive teachers feel they need to learn in order to continue as successful educators. A modified Borich (1980) needs assessment model was used to identify the perceived importance and ability levels for 32 professional competencies. Mean Weighted Discrepancy Scores (MWDS) were calculated using the importance and ability scores in order to report the professional development need. The administered survey was also utilized to examine their …

Effects Of High Freestream Turbulence And Conduction On Film Cooling Effectiveness Of Shaped Holes, Richard A. Macias Jr.

Theses and Dissertations

With technological advancements allowing higher turbine temperatures, film cooling continues to be an important research area. The Film Cooling Rig (FCR) was fitted with a turbulence generator to vary freestream turbulence intensity and length scale, enabling the effects of high freestream turbulence on overall effectiveness to be studied. A cylindrical hole and laidback fan-shaped hole were investigated over a range of Advective Capacity Ratio (ACR) for freestream turbulence intensities of 2%, 10%, and 15%. For a given ACR, increasing the turbulence intensity resulted in lower overall effectiveness values due to the larger heat transfer coefficient that comes from turbulent ow. …

Detonation Confinement In A Radial Rotating Detonation Engine, Kavi Muraleetharan

Theses and Dissertations

Radial Rotating Detonation Engines (RRDE) have provided an opportunity for use of a pressure-gain combustor in a more compact form compared to an axial RDE. A successfully tested RRDE has operated over a wide range of test conditions and produced detonation modes with one, two, and three waves. The presence of multiple waves located the detonation waves to the outer radius, while one wave modes operated closer to the inner radius. Locating the detonation wave closer to the inner diameter resulted in less time for combustion prior to the radial turbine. Subsequently, this tended to decrease efficiency. To attempt to …

Design And Analysis Of A Compact Combustor For Integration With A Jetcat P90 Rxi, Daniel Holobeny

Theses and Dissertations

Ultra Compact Combustors are a novel approach to modern gas turbine combustor designs that look to reduce the overall combustor length and weight. A previous study integrated an Ultra Compact Combustor into a JetCat P90 RXi turbine engine and achieved self-sustained operation with a length savings of 33% relative to the stock combustor. However, that combustor could not operate across the full stock engine performance range due to flameout at increased mass ow rates as reactions were pushed out of the primary zone. To ensure reactions stayed in the primary zone, a new design with a larger combustor volume was …

Evaluating The Effectiveness Of Aerospace Materials, Vehicle Shape And Astronaut Position At Lowering The Whole Body Effective Dose Equivalent In Deep Space, Daniel K. Bond

Theses and Dissertations

As future crewed, deep space missions are being planned, it is important to assess how spacecraft design can be used to minimize radiation exposure. Collectively with shielding material, vehicle shape and astronaut position must be used to protect astronauts from the two primary sources of space radiation: Galactic Cosmic Rays (GCR) and Solar Particle Events (SPE). GCRs, which are composed of low intensity, highly energetic, and fully ionized stable and meta-stable isotopes, are considered a chronic source of radiation risk to the astronauts. SPEs, which originate from solar coronal mass ejections, are composed mostly of high intensity protons that can …

Development Of An Anatomically And Electrically Conductive Brain Phantom For Transcranial Magnetic Stimulation, Hamzah A. Magsood

Theses and Dissertations

Transcranial Magnetic Stimulation (TMS) is a non-invasive technique for diagnostics, prognostic, and treatments of various neurological diseases. However, the lack of anatomically realistic brain phantoms has made the experimental verification of stimulation strength in the form of induced electric fields/voltages in the brain tissues an impediment to developing new TMS coils, stimulators, and treatment protocols. There are significant technological, safety, and ethical limitations to test the potential TMS treatment procedures or develop enhancements and refine them on humans or animals. This work aims to bridge the gap by introducing and developing an innovative manufacturing and fabrications process to produce a …

Development Of A Single Use Device Intended To Wash Blood Clot Debris From A Stent Retriever In The Operating Room, Shane Diller

Theses and Dissertations

Ischemic stroke is a life-threatening condition that requires immediate surgical intervention to remove the blood clot that is lodged in the blood vessels of the brain. Mechanical thrombectomy, performed by an endovascular surgeon, involves inserting a stent retriever, which deploys distally and attempts to capture the clot when dragged backwards. A complication prevalent in 50% - 67% of cases is that the blood clot is only partially removed and clings to the mesh framework of the stent. The operating surgeon must either clean the debris from the stent retriever, to be reinserted or throw the stent retriever away and open …

Quantification And Modeling Of Bladder Biomechanics Mechanisms Linking Spontaneous Rhythmic Contractions And Dynamic Elasticity To Detrusor Overactivity, Zachary E. Cullingsworth

Theses and Dissertations

Overactive bladder (OAB) is a chronic condition affecting approximately 20% of adults in the United States. Detrusor overactivity (DO) is the presence of non-voiding contractions in the detrusor (bladder) muscle during filling and is present in some individuals with OAB. DO is currently identified visually during a urodynamics (UD) study involving pressure catheters and filling and voiding of the bladder to evaluate function. UD provides limited subtyping of DO, and an incomplete understanding of mechanisms contributing to OAB.

Aim 1 of this study was to develop objective tools to quantify, subgroup and better understand …

Peridynamic Approaches For Damage Prediction In Carbon Fiber And Carbon Nanotube Yarn Reinforced Polymer Composites, Forrest E. Baber

Theses and Dissertations

Aerospace structures are increasingly utilizing advanced composites because of their high specific modulus and specific strength. While the introduction of these material systems can dramatically decrease weight, they pose unique certification challenges, often requiring extensive experimental testing in each stage of the design cycle. The expensive and time-consuming nature of experimental testing necessitates the advancement of simulation methodologies to both aid in the certification process and assist in the exploration of the microstructure design space.

Peridynamic (PD) theory, originating from Sandia National Lab’s in the early 2000’s, is a nonlocal continuum-based method that reformulates the equation of motion into an …

Strategies And Devices For Improving Respiratory Drug Delivery To Infants And Children With Cystic Fibrosis, Karl Bass

Theses and Dissertations

Cystic Fibrosis (CF) is a degenerative disease, which causes thickening of the airway surface liquid and reduced mucociliary clearance, which provides an ideal habitat for bacterial infections. Early treatment of CF in children can prevent chronic infection, improve quality of life, and increase life expectancy. The most predominant bacteria found in CF-diseased lungs is Pseudomonas aeruginosa (Pa), which can be treated with inhaled tobramycin. Excipient enhanced growth (EEG) powder formulations are well suited for administering tobramycin to children, as the EEG approach provides minimal upper airway loss and targeted drug delivery. This method uses an initially small aerosol for high …