Mechanical Engineering Commons^™

Experimental Observation Of Sphere Symmetric Isolated Single Droplet Combustion In A Converging Channel, Mason Carrington Williams

Theses and Dissertations

Spherically symmetric isolated single droplet combustion has been observed mainly in microgravity conditions. This study sought to determine if spherically symmetric combustion can be produced in a lab-scale experiment using flow acceleration to counteract the effects of buoyancy. The experiment was conducted in a converging channel that decreased in width along its length to accelerate the flow and limit the formation of a boundary layer. The rate at which the area decreased was governed by the initial velocity condition set at the channel inlet.

The droplets were generated using a piezoelectric actuator which forced fuel out of an injector with …

Leveraging Automated Fiber Placement Computer Aided Process Planning Framework For Defect Validation And Dynamic Layup Strategies, Joshua Allen Halbritter

Theses and Dissertations

Process planning represents an essential stage of the Automated Fiber Placement (AFP) workflow. It develops useful and efficient machine processes based upon the working material, composite design, and manufacturing resources. The current state of process planning requires a high degree of interaction from the process planner and could greatly benefit from increased automation. Therefore, a list of key steps and functions are created to identify the more difficult and time-consuming phases of process planning. Additionally, a set of metrics must exist by which to evaluate the effectiveness of the manufactured laminate from the machine code created during the Process Planning …

Development Of System Pressure Drop Calculation Methods For Dilute Phase Pneumatic Conveying, Ross Daniel Gorman

Theses and Dissertations

This work is focused on dilute and dense phase pneumatic conveying of bulk solids. The motivation of this work is to use industrial data to scale up existing models for pressure drop in pneumatic conveying systems, determine which models best predict pressure drop in full conveying systems, and find the empirical coefficients that go with these models.

Several major research objectives were accomplished by this work. First, system pressure drop methods were evaluated in this research. Other researchers have focused on single pipe section type pressure drops. Second, the data used in this research both for the machine learning evaluations …

Timing Deterministic Structural Model Updating Considering Impact And Fatigue Damage, Jason Michael Smith Jr.

Theses and Dissertations

Naval ship structures such as support trusses, hull sections, driving machinery, and load-bearing beams are subjected to various damage states that develop on short-term (i.e. impact) and long-term (i.e. fatigue) timescales. Naval structures fitted with a structural health monitoring system with damage detection abilities will enable appropriate real-time adjustments to the ships’ posture and control policies and thus have increased survivability and lethality. A digital twin can provide real-time condition assessment of naval structures when conjoined with a decision-making framework will increase naval ship survivability through informed response management. A fundamental challenge for the development of digital twins is reliable …

Vision Controlled Autonomous Stakebot For Driving Stakes And Its Digital-Twin, Corey Lee Leydig

Theses and Dissertations

In this thesis a novel vision-based AI driven autonomous ‘StakeBot’ is proposed to serve the agricultural 4.0 industries of the future. In recent years supply, demand and production of vegetables that are harvested from plants with weak stems like bell pepper, tomato, eggplant has been significantly up by several fold. With growing demand and new green-house establishments across the country production of vegetables will require a tremendous number of labors which will be hard to supply soon. To overcome the issues in addition to the labor shortages, automation through robotics will be the only viable solution. Plants like bell peppers …

An Artificial Intelligence Approach To Fatigue Crack Length Estimation From Acoustic Emission Signals, Shane T. Ennis

Theses and Dissertations

As in service aircraft begin to age and fatigue, a method for evaluating the operational life they are currently operating under and have remaining comes into question. Structural health monitoring is (SHM) is a popular method of structural analysis with growing interest in the aerospace industry. SHM is capable of damage assessment and structural life estimations.

The ultimate goal of the research presented in this thesis is to develop a methodology of classifying the length of a fatigue crack though the use of machine learning. The thesis has three major chapters as described below.

The first chapter deals with the …

An Autonomous Aerial Drone System For Water Fluorescence Mapping And Targeted Sampling, Kazi Ragib Ishraq Sanim

Theses and Dissertations

At present, aerial drones, also known as Uncrewed Aircraft Systems (UAS) or Unmanned Aerial Vehicles (UAV), are increasingly used in time and effort-heavy scientific exploration applications. One such application is inspecting the physical, chemical, and biological state of water bodies. This thesis presents a novel autonomous system capable of sensing water properties and collecting up to three 250 mL water samples from multiple sampling locations. The system features a customized aerial drone with an in-house built fluorescence sensor and pumping mechanism. It can also map the gradient of fluorescent content across the body of water to determine the best sampling …

Nondestructive Damage Detection And Stress Corrosion Crack Mitigation In Stainless Steel Plates, Andrew Philip Campbell

Theses and Dissertations

The ability to inspect and detect damage within a structure without permanent damage has broad appeal in a range of engineering applications from aerospace structures to nuclear facilities. Non-destructive evaluation (NDE) using guided ultrasonic Lamb waves has growing potential and popularity in these fields. Lamb waves are known for being sensitive to material properties and various defects across the thickness such as cracks in metallic structures and delamination or debonding in composite structures. Research has also been done on the development of fully non-contact system that generates and detects Lamb waves, particularly focused on the use of pulsed laser for …

Comprehensive Process Planning Optimization Framework For Automated Fiber Placement, Alex Ryan Brasington

Theses and Dissertations

Advanced composite materials came about in 1966 and have since been widely used due to the possibility of superior structural performance while also achieving weight reductions. Such opportunities have led to composite materials being used to fabricate complex components, often in the aerospace sector. Most components, especially in aviation, are on a large scale and are outside the capabilities of traditional composite manufacturing techniques. Traditional manufacturing methods are also labor intensive, time consuming, have a high level of material scrap, and are prone to human error. This has led to the need for innovative manufacturing solutions to withstand the ever-increasing …

Multidimensional Transport-Coupled Numerical Investigation Of Non-Premixed Low-Temperature Flame In Atmospheric And High-Pressure Systems, Sudipta Saha

Theses and Dissertations

Gas-phase chemical reactions coupled with multidimensional fluid flow and heat and mass transport are found in various applications, i.e., from conventional engine applications to novel combustion techniques. With the goal of understanding such complex coupling in reacting flow systems, this dissertation work focuses on developing multi-physics simulation frameworks to investigate the effect of multidimensional transport on flame dynamics. This study primarily focuses on the modeling and simulation of low temperature flame formation in i) a canonical experimental setting with counterflow burners and ii) a supercritical water medium (i.e., hydrothermal flame).

In the first part of the dissertation, simulations of the …

Modeling The Effects Of Radiation On Microelectromechanical Resonators, David D. Lynes

Theses and Dissertations

As the use of MEMS becomes more prolific in air, space, defense, and power applications, they will be exposed to more extreme radiation environments. This dissertation explores the effects of ionizing and nonionizing radiation on MEMS. AlN-on-Si based piezoelectric bulk acoustic wave resonators were irradiated by gamma-rays and silicon ions while measuring S-parameters in situ. Changes to the resonator and equivalent circuit parameters are extracted. The resonators demonstrated resilience against the effects of radiation-induced charge trapping. However, radiation-induced atomic displacements caused shifts to resonant frequency. From these data, an atomistic model is derived to describe the relationship between radiation type …

Shock Induced Trailing Edge Separation Effect On F-16 Limit-Cycle Oscillation, Eric D. Stubblefield

Theses and Dissertations

No abstract provided.

Detonation Confinement In A Second-Generation Radial Rotating Engine, John T. Ursino

Theses and Dissertations

In recent years, Rotating Detonation Engines (RDEs) have been coupled with turbomachinery to harness the benefits of detonative combustion. A novel type of RDE, referred to as the disk or Radial RDE (RRDE), has been developed in pursuit of length and weight savings compared to a traditional annular flow RDE. This design includes a disk-shaped device within which reactants flow from the outer radius, detonate, and exit the inner radius. In this paper several modifications have been made to a previously tested RRDE to address issues that arose with the original design. The combustion chamber diameter has been increased to …

Development Of Novel Turbomachinery Manufacturing Methods, Timothy P. Winkler

Theses and Dissertations

Compact turbine engines are of increasing interest as a means of propulsion for small, lightweight, low cost, unmanned aerial systems. This study looks to leverage advancements in novel manufacturing technology to produce turbomachinery components while simultaneously reducing costs and manufacturing time. To determine the feasibility of drop-in replacements for stock components this study focused on several research areas. This included materials research on both polymer-reinforced and ceramic materials, specimen tensile testing to determine temperature-dependent material properties, finite element analysis of multiple candidate materials, design and fabrication of a spin test rig, and physical spin testing of manufactured components to predict …

Material Property Dependence Of Nanoparticle Silicon Carbide Alloying In Additively Manufactured Molybdenum, Andrew P. Mason

Theses and Dissertations

The structural performance of additively manufactured Mo printed by LPBF can be significantly improved by nanoparticle alloying. Previous AFIT studies of SiC nanoparticle addition conducted by Ellsworth (2022) et al. demonstrated increased powder consolidation, leading to reduced porosity, increased microhardness, and a shift in atomic defect concentrations. The addition of defected SiC particles is proposed to reduce in situ oxidation by acting as a sacrificial oxidizing agent and contributing to the formation of Mo disilicide secondary phases. This study investigated the relationship between laser powder bed fusion Mo microscale and nanoscale properties with varying SiC particle size while maintaining a …

Biogas Combustion Characteristics In A Concentric Flow Slot Burner: Effects Of Co2 Concentration On Stability And Flame Structure, Maged Kiriakos

Theses and Dissertations

Biogas combustion is affected by the concentration of carbon dioxide. The successful applications of Biogas as a sustainable renewable alternative fuel produced from waste depend on its combustion stability, heat release, and pollution level. The aim of the current study is to apply new combustion technology and study the stability and combustion characteristics of natural gas with different percentages of carbon dioxide from 0 to 40% simulating biogas fuel. The stability characteristics and the temperature profiles of turbulent planar flames at different levels mixture inhomogeneity are investigated and presented in this work. The flames are created in a newly developed …

Accurate Evaluation Of The Direction-Dependent Mechanical Properties Of Ideal Single Crystals: A Comparative Ab Initio Study, Jaylan Ali Elhalawani

Theses and Dissertations

The mechanical properties of a single crystal or a grain in a polycrystalline material are highly dependent on the direction of the applied load. Key properties of interest are the Young’s modulus and the Poisson ratio in the small strain limit, and the ideal tensile strength in the large strain regime. Prior atomistic computations of these properties interchangeably used two approaches. In one approach the stress-strain response is explicitly calculated via a numerical tensile test experiment. In the second approach the second order single crystal elastic constants are computed via small deformations and then used in analytical equations to derive …

Estimating Solar Energy Production In Urban Areas For Electric Vehicles, Shaimaa Ahmed

Theses and Dissertations

Cities have a high potential for solar energy from PVs installed on buildings' rooftops. There is an increased demand for solar energy in cities to reduce the negative effect of climate change. The thesis investigates solar energy potential in urban areas. It tries to determine how to detect and identify available rooftop areas, how to calculate suitable ones after excluding the effects of the shade, and the estimated energy generated from PVs. Geographic Information Sciences (GIS) and Remote Sensing (RS) are used in solar city planning. The goal of this research is to assess available and suitable rooftops areas using …

A 3d Bioprinted Hydrogel Microfluidic Device For Screening Applications, Anant Bhusal

Theses and Dissertations

The microfluidic enabled the integration of engineered miniaturized tissue models for drug screening. Conventional polydimethylsiloxane or plastic-based devices require multiple fabrication steps, which are challenging. We developed a 3D bioprinting approach to create prototypes of hydrogel-based multi-material microfluidic devices integrated with microtissue models. The approach utilizes poly(ethylene glycol) diacrylate and gelatin-methacryloyl to create microfluidic chips using multi-material bioprinting capacity with a high resolution of 15µm on x-y and 50µm on the z-axis and post-printing viability of >90%. We demonstrated easy regulation of stiffness from 24±5 kPa to 1,180±9 kPa and burst pressure from 16±1kPa to 256±19 kPa in the chip …

Using Dielectric Scatters To Selectively Excite Embedded Eigenstates In Cavity Resonators, Olugbenga Joshua Gbidi

Theses and Dissertations

Bound states in the continuum (BICs) are waves that remain in the continuous spectrum of radiating waves that carry energy, however, still localized within the spectrum. BICs, also embedded eigenmodes, exhibit high quality factors that have been observed in optical and acoustic waveguides, photonic structures, and other material systems. Presently, there are limited means to select these BICs in terms of the quality factor and their excitation. In this work, we show that a different type of BIC, Quasi-BICs (Q-BICs), in open resonators can have their quality attuned by introducing embedded scatters. Using microwave cavities and dielectric scatters as an …

Material Extrusion-Based Additive Manufacturing: G-Code And Firmware Attacks And Defense Frameworks, Haris Rais

Theses and Dissertations

Additive Manufacturing (AM) refers to a group of manufacturing processes that create physical objects by sequentially depositing thin layers. AM enables highly customized production with minimal material wastage, rapid and inexpensive prototyping, and the production of complex assemblies as single parts in smaller production facilities. These features make AM an essential component of Industry 4.0 or Smart Manufacturing. It is now used to print functional components for aircraft, rocket engines, automobiles, medical implants, and more. However, the increased popularity of AM also raises concerns about cybersecurity. Researchers have demonstrated strength degradation attacks on printed objects by injecting cavities in the …

Thermal Performance And Fluid Flow Studies Of Twisted Tape Inserts Using Scaled Surrogate Fluids For Molten Salt Energy Applications, Arturo Cabral

Theses and Dissertations

Global energy consumption is expected to increase with population growth and innovative clean sources of energy are sought out that can help meet the needs of a continuously power-hungry world. Some of these innovative sources of energy use molten salts as their operating and cooling fluid, such as fission reactors, fusion reactors, and solar power with energy storage. Molten salts are considered due to their efficient heat transfer properties, thermal energy storage capabilities, and high operating temperatures. To expedite their deployment, a further understanding of the heat transfer systems is required to accurately design and develop the heat transfer components …

Advanced Modeling And Innovative Transcranial Magnetic Stimulation Coil Designs For The Treatment Of Neurological Disorders, Mohannad Tashli

Theses and Dissertations

Transcranial magnetic stimulation (TMS) is a safe, effective and non-invasive treatment for several mental and psychiatric disorders. TMS is an FDA approved treatment and is commonly applied to patients who do not respond to medications for the treatment of clinical depression, smoking cessation, obsessive-compulsive disorder and migraine. Recently, there has been an increase in the development of electromagnetic neuromodulation techniques targeted at enhancing the effectiveness of TMS devices for the treatment of mental diseases. In TMS stimulation, focality is an important factor which determines the specificity of the pulses induced in different brain tissues. The electromagnetic pulses must be confined …

Aerosol Synthesis Of Tungsten Bronze Particles For Nir Shielding, Hao Tu

Theses and Dissertations

This dissertation emphasizes the need for efficient energy use in buildings and transportation due to global warming and the energy crisis. It suggests that improving energy efficiency can help reduce energy consumption and emissions and support sustainability. The dissertation introduces various transparent materials that can block near-infrared (NIR) radiation from solar radiation to save energy and money, and it highlights the growing market value of such products. The dissertation compares tungsten bronze with other NIR shielding materials and shows its advantages. The dissertation introduces a cheap and environmentally friendly method for continuously producing tungsten bronze particles via aerosol synthesis. Particle …

Pms And Gas Pollutants Removal By Electret Filter Media And Metal-Organic Frameworks (Mofs), Yu Zhang

Theses and Dissertations

Indoor air quality (IAQ) has been becoming a major concern worldwide because statistical data showed that the indoor concentrations of gas pollutants, e.g., volatile organic compounds (VOCs) and particulate matters (PMs) are often 2–5 times higher than that of outdoors. Especially, people spend 87% of their time indoors and increasing to more than 90% during COVID-19 pandemic. The high concentration of these indoor air pollutants is mainly due to the reduced air exchange rate for the design of energy-efficient building construction and the increased usage of furnishings, glues, paints, furnaces, etc., leading to VOC outgassing and particle emission. Evidence has …

Design, Development And Evaluation Of The Ruggedized Edge Computing Node (Recon), Sahil Girin Patel

Theses and Dissertations

The increased quality and quantity of sensors provide an ever-increasing capability to collect large quantities of high-quality data in the field. Research devoted to translating that data is progressing rapidly; however, translating field data into usable information can require high performance computing capabilities. While high performance computing (HPC) resources are available in centralized facilities, bandwidth, latency, security and other limitations inherent to edge location in field sensor applications may prevent HPC resources from being used in a timely fashion necessary for potential United States Army Corps of Engineers (USACE) field applications. To address these limitations, the design requirements for RECON …

Molecular Dynamics Of High Temperature Hydrogen Attack, Mike Travis Bodden Connor

Theses and Dissertations

High temperature hydrogen attack (HTHA) is a damage mechanism that only affects carbon steel and low alloy material. Most of the data regarding HTHA are experimental-driven. Even though this approach has been successful, there are still much more things that the oil and gas industry does not understand about HTHA. The regions that were considered safe (below the Nelson curves) have experienced catastrophic failure. Our research consists of performing Molecular Dynamics (MD) and the Nudge Elastic Band (NEB) calculation of HTHA to better understand the atomistic behavior of this damage mechanism.

Numerical Study Of Advanced Solar Receiver Tubes Based On A Coupled Thermo-Mechanical Analysis For Concentrated Solar Power Tower Plant, Shawn Michael Hatcher

Theses and Dissertations

The search for more sustainable energy to match the growing energy demand begins with finding more dispatchable resources such as solar energy. As one of the promising solar technologies, concentrated solar power (CSP) has a full capacity to store thermal energy for extended operation. Nevertheless, some key components in CSP systems usually face extreme environment, such as uneven solar flux, cyclic thermal expansion, structural degradation on the solar absorber tubes in a Concentrated Solar Power Tower (CSPT) Plant. In this study, we applied Multiphysics simulation to explore the benefits of introducing optimized fins for heat transfer enhancement and uniform temperature …

A Constitutive Material Model For Simulating Texture Evolution And Anisotropy Effects In Cold Spray., Creston Michael Giles

Theses and Dissertations

Cold spray has seen rapid advancement since its inception and has shown significant potential as a method of additive manufacturing. However, the large plastic deformation and repeated heating/cooling cycles that the material undergoes during the cold spray process can result in gradients in material structure and large residual stresses. The purpose of this study is to extend the existing EMMI material model to include anisotropic material response through the use of orientation distribution functions to predict residual stresses and anisotropy resulting from cold spray and similar additive manufacturing processes. Through the use of a finite element simulation, yield surfaces for …

Development Of Alternative Air Filtration Materials And Methods Of Analysis, Ivan Philip Beckman

Theses and Dissertations

Clean air is a global health concern. Each year more than seven million people across the globe perish from breathing poor quality air. Development of high efficiency particulate air (HEPA) filters demonstrate an effort to mitigate dangerous aerosol hazards at the point of production. The nuclear power industry installs HEPA filters as a final line of containment of hazardous particles. Advancement air filtration technology is paramount to achieving global clean air. An exploration of analytical, experimental, computational, and machine learning models is presented in this dissertation to advance the science of air filtration technology. This dissertation studies, develops, and analyzes …