Mechanical Engineering Commons^™

An Efficient Constructive Heuristic To Balance Trade-Offs Between Makespan And Flowtime In Permutation Flow Shop Scheduling, Feidi Dang, Wei Li, Honghan Ye

Mechanical Engineering Faculty Publications

Balancing trade-offs between production cost and holding cost is critical for production and operations management. Utilization of a production line affects production cost, which relates to makespan, and work-in-process (WIP) inventories in a production line affect holding cost, which relate to flowtime. There are trade-offs between two objectives, to minimize makespan and to minimize flowtime. Without addressing trade-off balancing issues in flow shop scheduling, WIP inventories are still high in manufacturing, generating unnecessary holding cost. However, utilization is coupled with WIP inventories. Low WIP inventory levels might lower utilization and generate high production cost. Most existing constructive heuristics focus only …

Assessing Production Line Risk Using Bayesian Belief Networks And System Dynamics, Sudhir Punyamurthula, Fazleena Badurdeen

Mechanical Engineering Faculty Publications

Increased complexity in product design, strict regulations and a changing market make risk assessment critical for successful operations. Failure in responding quickly to raw material shortages, downtimes, deteriorating equipment conditions or other operational issues can prove to be an expensive affair. A company-wide risk assessment includes both external and internal operations. However, external/supplier risk assessment has been of major interest. Even though the scope of risk assessment at the production line level is not as broad as it is at the supply chain level, assessing risk would help recognize vulnerable areas of the production line, which would in turn help …

Low-Cost Experimental System For Center Of Mass And Center Of Pressure Measurement, Cai Xia Yang

Mechanical Engineering Faculty Publications

Falls happen when the center of mass of body is outside of its base of support and the recovery of the center of mass back to the base of support failed. Balance ability is an essential ability needed for humans' daily routine activities. Improving balance ability should result in a better and more convenient way of living. There are various factors influence on balance ability. The focus of this paper is to investigate which factors have the greatest effect on balance. Balance ability is measured by deviations of center of pressure in both x-direction (side-to-side) and y-direction (front-to-back) with the …

Considerations For Atmospheric Measurements With Small Unmanned Aircraft Systems, Jamey D. Jacob, Phillip B. Chilson, Adam L. Houston, Suzanne Weaver Smith

Mechanical Engineering Faculty Publications

This paper discusses results of the CLOUD-MAP (Collaboration Leading Operational UAS Development for Meteorology and Atmospheric Physics) project dedicated to developing, fielding, and evaluating integrated small unmanned aircraft systems (sUAS) for enhanced atmospheric physics measurements. The project team includes atmospheric scientists, meteorologists, engineers, computer scientists, geographers, and chemists necessary to evaluate the needs and develop the advanced sensing and imaging, robust autonomous navigation, enhanced data communication, and data management capabilities required to use sUAS in atmospheric physics. Annual integrated evaluation of the systems in coordinated field tests are being used to validate sensor performance while integrated into various sUAS platforms. …

Texas Sour Orange Juice Used In Scaffolds For Tissue Engineering, Mandana Akia, Nataly Salinas, Cristobal Rodriguez, Robert Gilkerson, Luis A. Materon, Karen Lozano

Mechanical Engineering Faculty Publications

Fine fibers of polyhydroxybutyrate (PHB), a biopolymer, were developed via a centrifugal spinning technique. The developed fibers have an average diameter of 1.8 µm. Texas sour orange juice (SOJ) was applied as a natural antibacterial agent and infiltrated within the fibrous membranes. The antibacterial activity against common Gram-positive and Gram-negative bacteria (Staphylococcus aureus and Escherichia coli, respectively) was evaluated as well as cell adhesion and viability. The PHB/SOJ scaffolds showed antibacterial activity of up to 152% and 71% against S. aureus and E. coli, respectively. The cell studies revealed a suitable environment for cell growth and cell attachment. The outcome …

Compensation For Inertial And Gravity Effects In A Moving Force Platform, Sandra K. Hnat, Ben J.H. Van Basten, Antonie J. Van Den Bogert

Mechanical Engineering Faculty Publications

Force plates for human movement analysis provide accurate measurements when mounted rigidly on an inertial reference frame. Large measurement errors occur, however, when the force plate is accelerated, or tilted relative to gravity. This prohibits the use of force plates in human perturbation studies with controlled surface movements, or in conditions where the foundation is moving or not sufficiently rigid. Here we present a linear model to predict the inertial and gravitational artifacts using accelerometer signals. The model is first calibrated with data collected from random movements of the unloaded system and then used to compensate for the errors in …

Vibration-Based Defect Detection For Freight Railcar Tapered-Roller Bearings, Joseph Montalvo, Constantine Tarawneh, Arturo A. Fuentes

Mechanical Engineering Faculty Publications

The railroad industry currently utilizes two wayside detection systems to monitor the health of freight railcar bearings in service: The Trackside Acoustic Detection System (TADS™) and the wayside Hot-Box Detector (HBD). TADS™ uses wayside microphones to detect and alert the conductor of high risk defects. Many defective bearings may never be detected by TADS™ due to the fact that a high risk defect is considered a spall which spans more than 90% of a bearing’s raceway, and there are less than 20 systems in operation throughout the United States and Canada. Much like the TADS™, the HBD is a device …

Developing And Testing An Electronic Homework System To Improve Student Engagement And Learning In Engineering Thermodynamics, Stephen Crown, Constantine Tarawneh, Jazmin Ley

Mechanical Engineering Faculty Publications

An electronic homework delivery system was developed for an advanced undergraduate engineering thermodynamics course due to limitations in available electronic homework systems. A commercially available system was effectively used in the introductory course for simple problems. The complexity of problems in the advanced course made adoption of the same system problematic as students needed feedback in the problem solving process. A system was devised that delivers individual problems to each student, provides feedback throughout the process, and records results for assessment. The system has helped students become more active in homework assignments in both completing assignments and in doing original …

Impact Of Hysteresis Heating Of Railroad Bearing Thermoplastic Elastomer Suspension Pad On Railroad Bearing Thermal Management, Oscar O. Rodriguez, Arturo A. Fuentes, Constantine Tarawneh

Mechanical Engineering Faculty Publications

It is a known fact that polymers and all other materials develop hysteresis heating due to the viscoelastic response or internal friction. The hysteresis or phase lag occurs when cyclic loading is applied leading to the dissipation of mechanical energy. The hysteresis heating is induced by the internal heat generation of the material, which occurs at the molecular level as it is being disturbed cyclically. Understanding the hysteresis heating of the railroad bearing elastomer suspension element during operation is essential to predict its dynamic response and structural integrity, as well as to predict the thermal behavior of the railroad bearing …

Defect Prognostics Models For Spall Growth In Railroad Bearing Rolling Elements, Nancy De Los Santos, Constantine Tarawneh, Robert E. Jones, Arturo A. Fuentes

Mechanical Engineering Faculty Publications

Prevention of railroad bearing failures, which may lead to catastrophic derailments, is a central safety concern. Early detection of railway component defects, specifically bearing spalls, will improve overall system reliability by allowing proactive maintenance cycles rather than costly reactive replacement of failing components. A bearing health monitoring system will provide timely detection of flaws. However, absent a well verified model for defect propagation, detection can only be used to trigger an immediate component replacement. The development of such a model requires that the spall growth process be mapped out by accumulating associated signals generated by various size spalls. The addition …

An Analysis Of The Efficacy Of Wayside Hot-Box Detector Data, Constantine Tarawneh, James Aranda, Veronica Hernandez, Claudia J. Ramirez

Mechanical Engineering Faculty Publications

Wayside hot-box detectors (HBDs) are devices that are currently used to monitor bearing, axle, and brake temperatures as a way of assessing railcar component health and to indicate any possible overheating or abnormal operating conditions. Conventional hot-box detectors are set to alarm whenever a bearing is operating at a temperature that is 94.4°C (170°F) above ambient, or when there is a 52.8°C (95°F) temperature difference between two bearings that share an axle. These detectors are placed adjacent to the railway and utilize an infrared sensor in order to obtain temperature measurements. Bearings that trigger HBDs or display temperature trending behavior …

Uat Ads-B Data Anomalies And The Effect Of Flight Parameters On Dropout Occurrences, Asma Tabassum, William Semke

Mechanical Engineering Faculty Publications

An analysis of the performance of automatic dependent surveillance-broadcast (ADS-B) data received from the Grand Forks, North Dakota International Airport was carried out in this study. The purpose was to understand the vulnerabilities of the universal access transceiver (UAT) ADS-B system and recognize the effects on present and future air traffic control (ATC) operation. The Federal Aviation Administration (FAA) mandated all the general aviation aircraft to be equipped with ADS-B. The aircraft flying within United States and below the transition altitude (18,000 feet) are more likely to install a UAT ADS-B. At present, unmanned aircraft systems (UAS) and autonomous air …

3d Numerical Study Of Multiphase Counter-Current Flow Within A Packed Bed For Post Combustion Carbon Dioxide Capture, Li Yang, Fang Liu, Zhengchang Song, Kunlei Liu, Kozo Saito

Mechanical Engineering Faculty Publications

The hydrodynamics within counter-current flow packed beds is of vital importance to provide insight into the design and operational parameters that may impact reactor and reaction efficiencies in processes used for post combustion CO₂ capture. However, the multiphase counter-current flows in random packing used in these processes are complicated to visualize. Hence, this work aimed at developing a computational fluid dynamics (CFD) model to study more precisely the complex details of flow inside a packed bed. The simulation results clearly demonstrated the development of, and changes in, liquid distributions, wetted areas, and film thickness under various gas and liquid …

Fracture Initiation In A Transversely Isotropic Solid: Transient Three Dimensional Analysis, Louis Milton Brock

Mechanical Engineering Faculty Publications

A transversely isotropic solid is at rest, and contains a semi-infinite, plane crack. The axis of rotational material symmetry lies in the crack plane. Application of normal point forces to each face of the crack causes transient 3D growth. The related problem of discontinuities in displacement and traction that exist on regions that exhibit dynamic similarity is first considered. Analytic results are obtained in integral transform space. These lead to equations of the Wiener–Hopf type for the fracture problem. Analytic solutions are again obtained and, upon inversion, subjected to a dynamic energy release rate criterion that includes kinetic energy. A …

Development And Optimization Of Alumina Fine Fibers Utilizing A Centrifugal Spinning Process, Mandana Akia, Dulce Capitanachi, Misael E. Martinez, Carlos Hernandez, Hector De Santiago, Yuanbing Mao, Karen Lozano

Mechanical Engineering Faculty Publications

Highlights

• Successful synthesis of AIP/PVA composite fibers using Forcespinning® techniques.

• Optimization of the operating parameters applying response surface methodology (RSM).

• Fabrication of mesostructured gamma alumina and highly crystalline alpha alumina fine fibers.

Abstract

Aluminum isopropoxide and poly(vinylalcohol) fine fibers were successfully fabricated and optimized utilizing the response surface methodology. The optimized composite fibers showed mean fiber diameter of 304 nm. The fiber samples were calcined at different temperatures to attain both gamma and alpha phases of alumina. Various characterization methods including scanning electron microscopy, thermogravimetric analysis, x-ray diffraction and nitrogen adsorption/desorption analysis were conducted. The BET analysis …

Research And Development Of Powder Brazing Filler Metals For Diamond Tools: A Review, Fei Long, Peng He, Dusan P. Sekulic

Mechanical Engineering Faculty Publications

Powder brazing filler metals (PBFMs) feature a number of comparative advantages. Among others, these include a low energy consumption, an accurate dosage, a good brazeability, a short production time, and a high production efficiency. These filler metals have been used in the aerospace, automobile, and electric appliances industries. The PBFMs are especially suitable for diamond tools bonding, which involves complex workpiece shapes and requires accurate dosage. The recent research of PBFMs for diamond tools is reviewed in this paper. The current applications are discussed. The CuSnTi and Ni-Cr-based PBFMs have been the two commonly used monolayer PBFMs. Thus, the bonding …

Study Of Near-Cup Droplet Breakup Of An Automative Electrostatic Rotary Bell (Esrb) Atomizer Using High-Speed Shadowgraph Imaging, Jacob E. Wilson, Stephen William Grib, Adnan Darwish Ahmad, Michael W. Renfro, Scott A. Adams, Ahmad Salaimeh

Mechanical Engineering Faculty Publications

Electrostatic Rotary bell (ESRB) atomizers are used as the dominant means of paint application by the automotive industry. They utilize the high rotational speed of a cup to induce primary atomization of a liquid along with shaping air to provide secondary atomization and transport. In order to better understand the fluid breakup mechanisms involved in this process, high-speed shadowgraph imaging was used to visualize the edge of a serrated rotary bell at speeds varying between 5000 and 12,000 RPM and with a water flow rate of 250 ccm. A multi-step image processing algorithm was developed to differentiate between ligaments and …

Evaluation Of A Novel Finite Element Model Of Active Contraction In The Heart, Xiaoyan Zhang, Zhan-Qiu Liu, Kenneth S. Campbell, Jonathan F. Wenk

Mechanical Engineering Faculty Publications

Finite element (FE) modeling is becoming a widely used approach for the investigation of global heart function. In the present study, a novel model of cellular-level systolic contraction, which includes both length- and velocity-dependence, was implemented into a 3D non-linear FE code. To validate this new FE implementation, an optimization procedure was used to determine the contractile parameters, associated with sarcomeric function, by comparing FE-predicted pressure and strain to experimental measures collected with magnetic resonance imaging and catheterization in the ventricles of five healthy rats. The pressure-volume relationship generated by the FE models matched well with the experimental data. Additionally, …

The Use Of Fe3o4/Carbon Composite Fibers As Anode Materials In Lithium Ion Batteries, Howard Campos, Jonathan Ayala, Carolina Valdes, Jason Parsons, Mataz Alcoutlabi

Mechanical Engineering Faculty Publications

In the present work, results on the synthesis and mass production of polymer/ceramic composite fibers through Forcespinning® (FS) are reported. Magnetite (Fe3O4), has been considered as a good anode material for Lithium‒Ion Batteries (LIBs) due to its high theoretical capacity (~924 mAhg-1), low cost, and low toxicity. The Fe3O4/carbon composite, in the present study, was achieved through Forcespinning iron (III) acetylacetonate /polyacrylonitrile (PAN) precursor solution with stabilization in air at 280°C followed by carbonization at 600°C under argon. The electrochemical cyclic performance of Fe3O4/C composite fibers was investigated by galvanostatic charge/discharge experiments. The results showed the Fe3O4/C composite fiber anode …

Scalable Patterning Using Laser-Induced Shock Waves, Saidjafarzoda Ilhom, Khomidkhodza Kholikov, Peizhen Li, Claire Ottman, Dylan Sanford, Zachary Thomas, Omer San, Haluk E. Karaca, Ali O. Er

Mechanical Engineering Faculty Publications

An advanced direct imprinting method with low cost, quick, and minimal environmental impact to create a thermally controllable surface pattern using the laser pulses is reported. Patterned microindents were generated on Ni₅₀Ti₅₀ shape memory alloys and aluminum using an Nd: YAG laser operating at 1064 nm combined with a suitable transparent overlay, a sacrificial layer of graphite, and copper grid. Laser pulses at different energy densities, which generate pressure pulses up to a few GPa on the surface, were focused through the confinement medium, ablating the copper grid to create plasma and transferring the grid pattern onto …

Optimal Mixed Tracking/Impedance Control With Application To Transfemoral Prostheses With Energy Regeneration, Gholamreza Khademi, Hanieh Mohammadi, Hanz Richter, Daniel J. Simon

Mechanical Engineering Faculty Publications

We design an optimal passivitybased tracking/impedance control system for a robotic manipulator with energy regenerative electronics, where the manipulator has both actively and semi-actively controlled joints. The semi-active joints are driven by a regenerative actuator that includes an energy-storing element. Method: External forces can have a large influence on energy regeneration characteristics. Impedance control is used to impose a desired relationship between external forces and deviation from reference trajectories. Multi-objective optimization (MOO) is used to obtain optimal impedance parameters and control gains to compromise between the two conflicting objectives of trajectory tracking and energy regeneration. We solve the MOO problem …

Modeling Of Nitihf Using Finite Difference Method, Nazanin Farjam, Reza Mehrabi, Haluk E. Karaca, Reza Mirzaeifar, Mohammad Elahinia

Mechanical Engineering Faculty Publications

NiTiHf is a high temperature and high strength shape memory alloy with transformation temperatures above 100oC. A constitutive model based on Gibbs free energy is developed to predict the behavior of this material. Two different irrecoverable strains including transformation induced plastic strain (TRIP) and viscoplastic strain (VP) are considered when using high temperature shape memory alloys (HTSMAs). The first one happens during transformation at high levels of stress and the second one is related to the creep which is rate-dependent. The developed model is implemented for NiTiHf under uniaxial loading. Finite difference method is utilized to solve the proposed equations. …

Selective Laser Melting Of Ni-Rich Niti: Selection Of Process Parameters And The Superelastic Response, Narges Shayesteh Moghaddam, Soheil Saedi, Amirhesam Amerinatanzi, Ehsan Saghaian, Ahmadreza Jahadakbar, Haluk E. Karaca, Mohammad Elahinia

Mechanical Engineering Faculty Publications

Material and mechanical properties of NiTi shape memory alloys strongly depend on the fabrication process parameters and the resulting microstructure. In selective laser melting, the combination of parameters such as laser power, scanning speed, and hatch spacing determine the microstructural defects, grain size and texture. Therefore, processing parameters can be adjusted to tailor the microstructure and mechanical response of the alloy. In this work, NiTi samples were fabricated using Ni_50.8Ti (at.%) powder via SLM PXM by Phenix/3D Systems and the effects of processing parameters were systematically studied. The relationship between the processing parameters and superelastic properties were investigated …

Influence Of Slm On Compressive Response Of Niti Scaffolds, Narges Shayesteh Moghaddam, Soheil Saedi, Amirhesam Amerinatanzi, Ahmadreza Jahadakbar, Sayed Ehsan Saghaian, Haluk E. Karaca, Mohammad Elahinia

Mechanical Engineering Faculty Publications

Porous Nickel-Titanium shape memory alloys (NiTi-SMAs) have attracted much attention in biomedical applications due to their high range of pure elastic deformability (i.e., superelasticity) as well as their bone-level modulus of elasticity (E≈12-20 GPa). In recent years, Selective Laser Melting (SLM) has been used to produce complex NiTi components. The focus of this study is to investigate the superelasticity and compressive properties of SLM NiTi-SMAs. To this aim, several NiTi components with different level of porosities (32- 58%) were fabricated from Ni_50.8Ti (at. %) powder via SLM PXM by Phenix/3D Systems, using optimum processing parameter (Laser power-P=250 W, …

Experimental Examination Of Vorticity Stripping From A Wing-Tip Vortex In Free-Stream Turbulence, Hari C. Ghimire, Sean C. C. Bailey

Mechanical Engineering Faculty Publications

Time-resolved stereoscopic particle image velocimetry measurements were conducted of a wing-tip vortex decaying in free-stream turbulence. The objective of the research was to experimentally investigate the mechanism causing the increased rate of decay of the vortex in the presence of turbulence. It was observed that the circulation of the vortex core experienced periods of rapid loss and recovery when immersed in free-stream turbulence. These events were not observed when the vortex was in a laminar free stream. A connection was made between these events and distortion of the vortex, coinciding with stripping of core fluid from the vortex core. Specifically, …

Modeling Of Aggregation And Gelation Of Nanoparticles Using Quadrature Method Of Moments, Elsayed Abdelfatah, Maysam Pournik

Mechanical Engineering Faculty Publications

Applications of Nanotechnology are growing significantly in the petroleum industry such as oil recovery, and well stimulation. In aqueous media, silica nanoparticles aggregate if there is sufficient attractive energy between nanoparticles. Aggregate size distribution evolves as aggregation continues, and once it spans the space, it forms a gel. The objective of this study is to study the aggregation and gelation kinetics in the batch. Population Balance equation (PBE) is used to model the kinetics of aggregation. Quadrature method of moments (QMOM) is used to convert the PBE with continuous distribution of nanoparticle size into a set of moment equations for …

Functionalized Graphene Oxide As Reinforcement In Epoxy Based Nanocomposites, F. V. Ferreira, F. S. Brito, W. Franceschi, E. A. N. Simonetti, L. .S Cividanes, Mircea Chipara, Karen Lozano

Mechanical Engineering Faculty Publications

The effects of amine-modified graphene oxide on dispersion and micro-hardness of epoxy based nanocomposites are reported. Graphene oxide was prepared by the modified Hummers method followed by hexamethylenediamine functionalization. Analysis conducted through Fourier transform infrared spectroscopy, Raman spectroscopy, X-ray photoelectron spectroscopy and atomic force microscopy-based infrared spectroscopy show that the functionalization process effectively promoted a replacement of oxygen with amine groups while simultaneously creating defects in the graphitic structure. An increase in hardness was observed for the developed nanocomposites.

Formation Of Two-Way Shape Memory Effect In Niti Alloy Using Pulsed Laser Irradiation, Saidjafarzoda Ilhom, Khomidkhodza Kholikov, Peizhen Li, Dovletgeldi Seyitliyev, Zachary Thomas, Duvall Roberts, Omer San, Haluk E. Karaca, Ali O. Er

Mechanical Engineering Faculty Publications

Shape memory alloys (SMAs) are a unique class of smart materials and they were employed in various applications in engineering, biomedical, and aerospace technologies. Here, we report an advanced, efficient, and low-cost direct imprinting method with low environmental impact to create thermally controllable surface patterns. Patterned microindents were generated on Ni₅₀Ti₅₀ (at. %) SMAs using an Nd:YAG laser with 1064 nm wavelength at 10 Hz. Laser pulses at selected fluences were focused on the NiTi surface and generated pressure pulses of up to a few GPa. Optical microscope images showed that surface patterns with tailorable sizes can …

Direct Numerical Simulation Of Transverse Ripples: 1. Pattern Initiation And Bedform Interactions, ‪Nadim Zgheib, J. J. Fedele, D. C. J. D. Hoyal, M. M. Perillo, S. Balachandar

Mechanical Engineering Faculty Publications

We present results of coupled direct numerical simulations between flow and a deformable bed in a horizontally periodic, turbulent open channel at a shear Reynolds number of Reτ = 180. The feedback between the temporally and spatially evolving bed and the flow is enforced via the immersed boundary method. Using the near-bed flow field, we provide evidence on the role of locally intense near-bed vortical structures during the early stages of bed formation, from the emergence of quasi-streamwise streaks to the formation of incipient bedform crestlines. Additionally, we take a new look at a number of defect-related bedform interactions, …

Direct Numerical Simulation Of Transverse Ripples: 2. Self-Similarity, Bedform Coarsening, And Effect Of Neighboring Structures, ‪Nadim Zgheib, J. J. Fedele, D. C. J. D. Hoyal, M. M. Perillo, S. Balachandar

Mechanical Engineering Faculty Publications

Coupled bed-flow direct numerical simulations investigating the early stages of pattern formation and bedform (ripple) interactions were examined in a previous paper (Part 1), making use of the resolved flow field. In this paper (Part 2), we compare our results to published experimental data and provide an extensive quantitative analysis of the bed using spectral analysis and two-point correlations. The effect of the mobile rippled bed on the flow structure and turbulence is investigated locally (at specific streamwise locations) and over the entire computational domain. We show that developing ripples attain a self-similar profile in both the shape and the …