Mechanical Engineering Commons^™

Child Carrier: Senior Project, Cordell Hollingsworth, Jacob Puppo, Drew Sapp

Mechanical Engineering

No abstract provided.

High Temperature Hepa Filter Test Unit Upgrades, Alexander Krippner, Ian Corcorran, Michael Burlando

Mechanical Engineering

No abstract provided.

High Speed Jet Turbine Test Final Report, Kenneth Enstrom, Cameron Naugle, Isaac Thomas, Cody Lee

Mechanical Engineering

At high flight altitudes and speeds, external airplane elements are subject to immense loads. External devices must be put through testing that simulates these loads to ensure safety of the device. Our system will subject a device in need of testing to a jet of air, similar to wind seen on the surface of an airplane. The High Speed Air Jet Turbine Test project team has been tasked to design, build, and test an apparatus capable of acquiring real world flight data for micro-ram air turbines (microRAT). The micro-RAT is a device that provides power to an electrical device by …

Sae Baja Dynamic Loading, Ryan Flatland, Christian George, Nick Bonafede

Mechanical Engineering

Cal Poly’s SAE Baja team undertook a project to measure the loads applied to an offroad buggy via the ground, including any obstacles. Originally, the ground loads pertaining to suspension, drivetrain, and chassis were based on rough estimates and historical part failures. This led to large safety factors, overbuilt parts, unknown part life, and improperly designed points of failure. In order for the team’s designs to advance to the next level of competition, an accurate set of loading cases were required. The main focus of the project was the suspension loads measured with strain gauges and a shock potentiometer, however …

Human Knee Joint Finite Element Model Using A Two Bundle Anterior Cruciate Ligament: Validation And Gait Analysis, Nicholas A. Czapla, Meghan K. Sylvia, Zachary F. Lerner, David J. Tuttle, Otto J. Schueckler, Scott J. Hazelwood, Stephen M. Klisch

Mechanical Engineering

No abstract provided.

Pseudo-Rigid Body Method For Reducing Soft Tissue Artifact: Validation And Application To Gait, Jake E. Deschamps, Karim C. Dudum, Eshan M. Dandekar, Scott Hazelwood, Stephen M. Klisch

Mechanical Engineering

No abstract provided.

Design And Implementation Of An Instrumented Pedal For Cycling Biomechanics Research, Luke I. Kraemer, Juan D. Gutierrez-Franco, Jake E. Deschamps, Karim C. Dudum, Eshan M. Dandekar, Scott Hazelwood, Hemanth V. Porumamilla, Stephen M. Klisch

Mechanical Engineering

No abstract provided.

Development Of A Human Knee Joint Finite Element Model To Investigate Cartilage Stress During Walking In Obese And Normal Weight Adults, Meghan K. Slyvia, Nicholas A. Czapla, Zachary F. Lerner, David J. Tuttle, Otto J. Schueckler, Scott Hazelwood, Stephen M. Klisch

Mechanical Engineering

No abstract provided.

Using Opensim To Predict Knee Joint Moments During Cycling, Karim C. Dudem, Jake E. Deschamps, Juan D. Gutierrez-Franco, Luke I. Kraemer, Alejandro M. Gonzalez-Smith, Eshan M. Dandekar, Scott Hazelwood, Stephen M. Klisch

Mechanical Engineering

No abstract provided.

Development And Implementation Of A Long-Term Freshmen Service Project: The Design And Deployment Of An Engineering Outreach Experience For Underserved Populations, James M. Widdmann, Brian P. Self, Peter Schuster

Mechanical Engineering

Freshmen year programs in engineering have received recent and growing attention as a method to engage first year students in their profession and start them on a path to success. Service learning is a well-known pedagogical method that has been shown to improve retention, especially of underrepresented groups in engineering, and to promote deeper learning through reflection. This paper describes the implementation of a new long-term (full year) service learning project where 240 freshmen mechanical engineering students worked together in small teams to design and deploy an engineering outreach experience for a designated age-group of 4th-11th grade students. This educational …

Forest Sign Maker, Victor Espinosa Iii, Kevin Ly, Lisa Yip

Mechanical Engineering

Executive Summary:

The Inyo National Forest is arguably one of the most beautiful locations in California, containing natural masterpieces such as Mount Whitney and the Ancient Bristlecone Pine Forest. Despite its magnificence, the Inyo National Forest can be a treacherous region. The Friends of the Inyo take pride in being able to facilitate the viewing experience for all outdoorsmen by maintaining the mountain trails, which includes providing adequate trail signage.

Unfortunately, there is a fundamental issue with the recent state of trail signage in the Inyo National Forest: the rate at which signs are being vandalized or naturally destroyed is …

Tadpole Tandem Electrically Assisted Tricycle, Austin Frederickson, Anthony Jacques, Kris Lawrence, Preston Mcelroy

Mechanical Engineering

The purpose of this senior project was to investigate the possibility of making bikes (as a regular mode of transportation) look much more appealing to the general public. To that end, an electric motor assist system was added to make it easier for the operators of the vehicle. A fairing was added to protect the rider from wind and rain, and an electrical subsystem consisting of a microcontroller and many other components was also added. The electrical subsystem was meant to store the information of different riders, calculate calories burned using a heart beat sensor, and increase visibility using strategically-placed …

Compact Tire Tester, Jess Mccafferty, Daniel Rodman, Michael Schuster, Connor West

Mechanical Engineering

No abstract provided.

Freedom Ski, Toby A. Goldsteinholm, Ashley Scharff, Justin Satnick, Markus Rutner

Mechanical Engineering

The current availability of water skis for people who are paraplegic or quadriplegic is very limited. The aim of our project is to design a system that improves upon the current models of specialized water skis. Our intent is to create a waterski system that is structurally stable and handles responsively, in order to ensure that anyone is capable of effectively using our system to waterski.

The main client of our project is Quality of Life Plus, an organization that aims to aid veterans of the armed forces who have physical disabilities to still enjoy a good quality of life. …

Mechanical Prosthetic Hand For Navy Seal, Ryan Burke, Michael Friedman, Jose Lemus, Heather Martin

Mechanical Engineering

Quality of Life Plus has been improving the lives of many wounded servicemen and first responders around the country. Its mission is to foster and generate innovations to aid and improve the quality of life for those injured in the line of duty. This project is the fifth iteration of designing a prosthetic hand for an active duty Navy SEAL. The first iterations have been myoelectric systems where sensors are attached to the user’s muscles to actuate the prosthetic. However, the most recent has been a purely mechanical system, and was shoulder actuated. The design was more robust, it was …

Jonathan’S Natural Juices Mechanical Juice Dispenser, Andrew Meyer, Jesus Gutierrez, Danielle Lauinger

Mechanical Engineering

Team AJD was tasked with trying to create a juice dispenser that did not utilize pumps, but rather explore the venturi effect to see if it could be a suitable substitute. The venturi effect is when a fluid in a pipe goes through a gradual reduction in diameter in a pipe to increase the velocity and lower the pressure of a fluid. Utilizing this principle the team constructed a testing device to be able to run tests and verify the theory. The team was able to verify that the venturi effect was able to make juice at the correct mix …

Team Solar Sip, Patrick Fillingham, Wesley Goodson, Kenneth Li

Mechanical Engineering

No abstract provided.

Smart Water Meter, Jeff Hufford, Eric Adler, Garrett Hall

Mechanical Engineering

No abstract provided.

Solar Decathlon 2015, Solar Cal Poly; Solar Cal Poly Project Engineers, Cristina Paquin, Julien Blarel, Sanchit Joshi

Mechanical Engineering

No abstract provided.

Cable Drag Test, Alex Powers, Brandon Sadiarin, George Rodriguez Iv, Torey Kruisheer

Mechanical Engineering

The Smooth Shifters is a team composed of Alex Powers, Brandon Roy Sadiarin, George Rodriguez, and Torey Kruisheer. We are four senior mechanical engineering students at California Polytechnic State University (Cal Poly) in San Luis Obispo, California that are working on a senior design project for Specialized Bicycle Components, Inc. located in Morgan Hill, California. We will be under the advisement of Professor Sarah T. Harding of the mechanical engineering department at Cal Poly.

Specialized, one of today’s leading bicycle companies, is in need of a test setup that measures brake and shifter cable drag. High performance cyclists using time …

Cal Poly Sae Formula Electric Chassis, Brandon Stitt, Rachel Brooks, Christopher L. Pell

Mechanical Engineering

The Cal Poly Formula Electric team has been in need of a chassis redesign, making that a logical choice for a senior project. The original goal of the project was to build the lightest possible frame while still maintaining adequate strength and stiffness. The existing frame made a good starting point. The steel tube spaceframe weighed a colossal 105 lb. There was ample room for improvement, even with a similar spaceframe design. The greatest potential to reduce weight lay in submitting designs under the Alternative Frame (AF) rule set. This could avoid the added weight of many required tubes. The …

Human Powered Vehicle Frame Design, Matthew S. Allen, Peter B. Aumann, Trent J. Hellmann

Mechanical Engineering

This report discusses the Human Powered Vehicle Frame Design senior project’s contributions to the design, manufacture, testing, and competition of the Cal Poly Human Powered Vehicle Club’s 2015 vehicle, Sweet Phoenix. The project’s guiding rules and timeline were dictated by the ASME Human Powered Vehicle Challenge (HPVC), held in April 2015. The Club sought to improve upon its previous vehicle, Aria, which suffered from a range of faults including a catastrophic structural failure at the 2014 HPVC. Largely in response to this failure, the Frame Design project’s major focus was Sweet Phoenix’s frame, from concept to manufacturing. During the design …

Deltronic Solutions Delta 3d Printer, Ramon Santos, Justin James, Taylor Chris, Stephen Marshall, Paul Maalouf

Mechanical Engineering

The Delta 3D Printer project is a 2014-2015 Cal Poly ME senior project sponsored by Dr. Jose Macedo, Professor and Department Chair of the Cal Poly IME Department; Yaskawa America, Inc., industry-leading producer of high-quality electronic drives and motors; and Bell-Everman, Inc., producer of high-precision embedded motion systems. The Delta 3D Printer project was conceived by Dr. Macedo as a collaboration between Cal Poly engineering and Yaskawa America. The majority of delta 3d printers on the market utilize stepper motors to control the print head motion. The 3D printer for this project was designed to use servo motors instead of …

Vibration Table For Environmental Chamber, Michael Czabaranek, Dylan De Caussin

Mechanical Engineering

No abstract provided.

Tesseract, Edgar Uribe, Vanessa Faune

Mechanical Engineering

PolySat is a student-run, Cal Poly research program in which students develop small satellites, known as CubeSats, to be sent into space. Since the start of the program in 2000, PolySat has developed eight 10cm x 10cm x10cm CubeSats. Recently, the team has developed two satellites of double, and triple, that size for NASA-KSC & AI-Solutions and the National Science Foundation. The recent volumetric expansion has been driven by high demand for further satellite functionality, which necessitates large power generation capabilities. To remain competitive in the growing CubeSat industry, PolySat must develop a platform that can provide enough power to …

Carbon Fiber Monocoque Development For A Formula Sae Racecar, Andrew Cunningham, Andrew Ferrell, Matthew Lee, Tony Loogman

Mechanical Engineering

Monocoque development of the 2015 Cal Poly Formula SAE racecar from design to competition.

Mini-Hand Extension, Aulivia Bounchaleun, Haden Cory, Scott Onsum, Zack Phillips

Mechanical Engineering

Lam Research supplies equipment for manufacturing silicon wafers used in semiconductor manufacturing. Their equipment is highly sophisticated and therefore costly, both in time and money, to repair. Much of the time and money spent to service those machines when they require maintenance or repair is spent on disassembly, so Lam seeks a faster way to service their equipment. Al Schoepp, a Senior Technical Director at Lam Research, came to Cal Poly seeking a team of students to design and build a device that could emulate the human hand well enough to handle hardware and thread nuts and bolts but also …

Final Design Report For An Automatic Diffraction Grating, Timothy Jung, Edlin Garcia, Kelly Rorden

Mechanical Engineering

The Automatic Diffraction Grating project explored using said technology to measure the angular separation between binary stars. This system would be a dramatic improvement from the current, fixed and manually adjusted diffraction gratings in use, increasing the capability of observatories to conduct autonomous studies of binary systems. Ideally, realizing such a system would be accomplished using a simple design and off the shelf parts, so that the project could easily replicated. The design of this system was approached with a broad look at the possible mechanisms that could be used to effectively construct an Automatic Diffraction Grating, as well as …

Pier2pier: Final Report, Kevin Nelson, Anthony Miller, Paul Maalouf, Chahan Shah

Mechanical Engineering

No abstract provided.

Active Fog Catcher, Michael Giglio, Carson Hand, William Beechinor, Kai Zhang

Mechanical Engineering

The active fog catching senior project team has been asked to develop a device that will harvest water from the atmosphere, namely fog, using active means. The project will be centered on maximizing water collection rate, with efficiency as a secondary concern. The final design utilizes a refrigeration system in which fans pull air across the cold evaporators inside of a duct. Water condenses on the evaporators and drain into a collection container. It was decided to focus on maximizing water collection at the cost of efficiency because the feasibility of actively harvesting fog must be proved before trying to …